Insight into permeability of protein through microcapsule membranes

The objective of this paper is to analyze the characteristics of protein permeability in alainate-polylysine-alginate (APA) and alginate-chitosan-alginate (ACA) microcapsules by mathematical models based on the balance of chemical potential. The comparison between calculated results and experimental data shows that the models can describe the process of protein diffusion from microcapsule and protein release into microcapsule successfully. The influences of membrane composition on the permeability of ACA microcapsule have been investigated and analyzed. The effect of resistance on the mass transfer is further analyzed theoretically with the aid of mathematical modeling. (c) 2005 Elsevier B.V. All rights reserved.

Development of a triple stage heat transformer for the recycling of low temperature heat energy

Absorption heat transformers are thermodynamic systems which are capable of recycling industrial waste heat energy by increasing its temperature. Triple stage heat transformers (TAHTs) can increase the temperature of this waste heat by up to approximately 145˚C. The principle factors influencing the thermodynamic performance of a TAHT and general points of operating optima were identified using a multivariate statistical analysis, prior to using heat exchange network modelling techniques to dissect the design of the TAHT and systematically reassemble it in order to minimise internal exergy destruction within the unit. This enabled first and second law efficiency improvements of up to 18.8% and 31.5% respectively to be achieved compared to conventional TAHT designs. The economic feasibility of such a thermodynamically optimised cycle was investigated by applying it to an oil refinery in Ireland, demonstrating that in general the capital cost of a TAHT makes it difficult to achieve acceptable rates of return. Decreasing the TAHT's capital cost may be achieved by redesigning its individual pieces of equipment and reducing their size. The potential benefits of using a bubble column absorber were therefore investigated in this thesis. An experimental bubble column was constructed and used to track the collapse of steam bubbles being absorbed into a hotter lithium bromide salt solution. Extremely high mass transfer coefficients of approximately 0.0012m/s were observed, showing significant improvements over previously investigated absorbers. Two separate models were developed, namely a combined heat and mass transfer model describing the rate of collapse of the bubbles, and a stochastic model describing the hydrodynamic motion of the collapsing vapour bubbles taking into consideration random fluctuations observed in the experimental data. Both models showed good agreement with the collected data, and demonstrated that the difference between the solution's temperature and its boiling temperature is the primary factor influencing the absorber's performance.

Turbulence modelling and its effects on electronic systems

This paper presents simulated computational fluid dynamics (CFD) results for comparison against experimental data. The performance of four turbulence models has been assessed for electronic application areas considering both fluid flow and heat transfer phenomenon. CFD is vast becoming a powerful and almost essential tool for design, development and optimization in engineering problems. However turbulence models remain to be the key problem issue when tackling such flow phenomena. The reliability of CFD analysis depends heavily on the performance of the turbulence model employed together with the wall functions implemented. To be able to resolve the abrupt changes in the turbulent energy and other parameters near the wall a particularly fine mesh is necessary which unfortunately increases the computer storage capacity requirements. The objective of turbulence modelling is to enhance computational procdures of sufficient acccuracy and generality for engineers to anticipate the Reynolds stresses and the scalar transport terms.

A note on the prediction of liquid hold-up with the stratified roll wave regime for gas/liquidco-current flow in horizontal pipes.

This note presents a simple model for prediction of liquid hold-up in two-phase horizontal pipe flow for the stratified roll wave (St+RW) flow regime. Liquid hold-up data for horizontal two-phase pipe flow [1, 2, 3, 4, 5 and 6] exhibit a steady increase with liquid velocity and a more dramatic fall with increasing gas rate as shown by Hand et al. [7 and 8] for example. In addition the liquid hold-up is reported to show an additional variation with pipe diameter. Generally, if the initial liquid rate for the no-gas flow condition gives a liquid height below the pipe centre line, the flow patterns pass successively through the stratified (St), stratified ripple (St+R), stratified roll wave, film plus droplet (F+D) and finally the annular (A+D, A+RW, A+BTS) regimes as the gas rate is increased. Hand et al. [7 and 8] have given a detailed description of this progression in flow regime development and definitions of the patterns involved. Despite the fact that there are over one hundred models which have been developed to predict liquid hold-up, none have been shown to be universally useful, while only a handful have proven to be applicable to specific flow regimes [9, 10, 11 and 12]. One of the most intractable regimes to predict has been the stratified roll wave pattern where the liquid hold-up shows the most dramatic change with gas flow rate. It has been suggested that the momentum balance-type models, which give both hold-up and pressure drop prediction, can predict universally for all flow regimes but particularly in the case of the difficult stratified roll wave pattern. Donnelly [1] recently demonstrated that the momentum balance models experienced some difficulties in the prediction of this regime. Without going into lengthy details, these models differ in the assumed friction factor or shear stress on the surfaces within the pipe particularly at the liquid–gas interface. The Baker–Jardine model [13] when tested against the 0.0454 m i.d. data of Nguyen [2] exhibited a wide scatter for both liquid hold-up and pressure drop as shown in Fig. 1. The Andritsos–Hanratty model [14] gave better prediction of pressure drop but a wide scatter for liquid hold-up estimation (cf. Fig. 2) when tested against the 0.0935 m i.d. data of Hand [5]. The Spedding–Hand model [15], shown in Fig. 3 against the data of Hand [5], gave improved performance but was still unsatisfactory with the prediction of hold-up for stratified-type flows. The MARS model of Grolman [6] gave better prediction of hold-up (cf. Fig. 4) but deterioration in the estimation of pressure drop when tested against the data of Nguyen [2]. Thus no method is available that will accurately predict liquid hold-up across the whole range of flow patterns but particularly for the stratified plus roll wavy regime. The position is particularly unfortunate since the stratified-type regimes are perhaps the most predominant pattern found in multiphase lines.

The VLT-FLAMES survey of massive stars: atmospheric parameters and rotational velocity distributions for B-type stars in the Magellanic Clouds

Aims.We aim to provide the atmospheric parameters and rotational velocities for a large sample of O- and early B-type stars, analysed in a homogeneous and consistent manner, for use in constraining theoretical models. Methods: Atmospheric parameters, stellar masses, and rotational velocities have been estimated for approximately 250 early B-type stars in the Large (LMC) and Small (SMC) Magellanic Clouds from high-resolution VLT-FLAMES data using the non-LTE TLUSTY model atmosphere code. This data set has been supplemented with our previous analyses of some 50 O-type stars (Mokiem et al. 2006, 2007) and 100 narrow-lined early B-type stars (Hunter et al. 2006; Trundle et al. 2007) from the same survey, providing a sample of ~400 early-type objects. Results: Comparison of the rotational velocities with evolutionary tracks suggests that the end of core hydrogen burning occurs later than currently predicted and we argue for an extension of the evolutionary tracks. We also show that the large number of the luminous blue supergiants observed in the fields are unlikely to have directly evolved from main-sequence massive O-type stars as neither their low rotational velocities nor their position on the H-R diagram are predicted. We suggest that blue loops or mass-transfer binary systems may populate the blue supergiant regime. By comparing the rotational velocity distributions of the Magellanic Cloud stars to a similar Galactic sample, we find that (at 3s confidence level) massive stars (above 8 M?) in the SMC rotate faster than those in the solar neighbourhood. However there appears to be no significant difference between the rotational velocity distributions in the Galaxy and the LMC. We find that the v sin i distributions in the SMC and LMC can modelled with an intrinsic rotational velocity distribution that is a Gaussian peaking at 175 km s-1 (SMC) and 100 km s-1 (LMC) with a 1/e half width of 150 km s-1. We find that in NGC 346 in the SMC, the 10-25 M? main-sequence stars appear to rotate faster than their higher mass counterparts. It is not expected that O-type stars spin down significantly through angular momentum loss via stellar winds at SMC metallicity, hence this could be a reflection of mass dependent birth spin rates. Recently Yoon et al. (2006) have determined rates of GRBs by modelling rapidly rotating massive star progenitors. Our measured rotational velocity distribution for the 10-25 M? stars is peaked at slightly higher velocities than they assume, supporting the idea that GRBs could come from rapid rotators with initial masses as low as 14 M? at low metallicities.

Extraction and purification of triterpenic acids from eucalypt bark

A indústria da pasta e do papel é um sector importante da economia mundial, particularmente a que assenta em espécies de Eucalyptus. No entanto, essas indústrias geram quantidades significativas de correntes secundárias de subprodutos e resíduos de biomassa que podem ser exploradas em aplicações de valor acrescentado em vez de serem queimadas para produção de energia. Um exemplo nobre pode ser a produção de ácidos triterpénicos com estruturas dos tipos lupano, oleanano e ursano, dada a sua abundância em alguns destes resíduos, em particular na casca, adotando o conceito de biorrefinaria integrada numa fábrica de pasta. Estes compostos são conhecidos pelas suas inúmeras actividades biológicas, por exemplo, antioxidante, anti-inflamatória e antitumoral, e podem encontrar aplicações em produtos de elevado valor, tais como cosméticos, nutracêuticos ou farmacêuticos. Neste sentido, o estudo das potencialidades das cascas das espécies de eucalipto mais exploradas enquanto fontes de compostos triterpénicos é um tópico relevante. Por conseguinte, foram analisados e comparados em pormenor os teores e composições em ácidos triterpénicos (TTAs) das cascas externas de várias espécies de eucalipto (E. globulus, E. grandis, E. urograndis, E. maidenii e E. nitens). Os teores dos principais TTAs identificados nestas espécies variaram entre 4.5 g/kg no E. urograndis e 21.6 g/kg no E. nitens. Observou-se que as cascas externas de Eucalyptus de zonas temperadas e Mediterrânicas, nomeadamente E. nitens e E. globulus, são mais ricas em TTAs que as espécies de regiões tropicais e subtropicais. Além disso, a casca externa do E. globulus é claramente a mais rica em ácidos com estruturas do tipo ursano enquanto a do E. nitens é a mais rica em ácidos do tipo oleanano e lupano. Estes resultados levaram-nos a estudar a extração dos TTAs da casca de Eucalyptus, bem como a sua posterior concentração e purificação, a qual foi efetuada por extração sólido-líquido convencional combinada com a precipitação de solutos, e por extração com fluidos supercríticos (SFE). No que diz respeito à primeira abordagem referida, foi desenvolvido neste trabalho um método patenteado que permite obter extratos enriquecidos em TTAs das cascas de eucalipto baseado em tecnologias disponíveis no imediato. Em relação à segunda abordagem, e de forma a apostar em processos de baixo impacto ambiental exigidos pelas biorrefinarias do futuro, a SFE surge como uma opção natural. Assim, foi efetuada a SFE da casca caduca do E. globulus com dióxido de carbono puro e modificado para recuperar a fração de TTAs, e os resultados foram comparados com os obtidos por extração em Soxhlet com diclorometano. Foram realizados estudos preliminares sobre a influência da pressão (100-200 bar), a adição de co-solvente (0, 5 e 8% m/m de etanol), e operação em múltiplos passos a fim de avaliar a aplicabilidade da alternativa supercrítica para a sua produção eficiente e selectiva. Os resultados destacaram a influência da pressão e o importante papel resumo (cont.) desempenhado pelo co-solvente neste processo, cujo efeito foi mais relevante do que o aumento da pressão em várias dezenas de bar. Este trabalho foi depois otimizado, usando o planeamento factorial de experiências e a metodologia de superfícies de resposta, para analisar a influência da temperatura (40-60 ºC), pressão (100-200 bar), e teor de etanol (0.0-5.0% m/m) na recuperação dos TTAs e respectiva concentração nos extractos. Nestes intervalos, as melhores condições de operação encontradas foram 200 bar, 40 °C e 5% de etanol, para as quais os modelos de regressão estatisticamente validados previram um rendimento de extração de 1.2% com 50% de concentração em TTAs, correspondendo ao rendimento em TTAs de 5.1 g/kg de casca e uma recuperação de 79.2% comparativamente ao valor do Soxhlet. Os TTAs livres e acetilados apresentaram tendências de extracção bastante distintas devido às suas diferentes afinidades para o CO2 causadas pelas diferentes polaridades: os derivados acetilados aproximam-se de um patamar máximo a cerca de 200 bar e 5% de etanol, enquanto a extração dos TTAs livres apresenta uma tendência sempre crescente no intervalo de condições estudado. Foram também medidas curvas cumulativas de SFE da casca do E. globulus de forma a analisar o comportamento cinético do processo em termos de rendimento total, rendimento em TTAs, rendimento em TTAs livres, rendimento em TTAs acetilados, e concentração dos TTAs nos extractos. Foi analisada a influência da pressão, temperatura, teor de co-solvente e caudal do dióxido de carbono sobre as respostas anteriores. Os dados experimentais foram modelados com os modelos Logístico, de Dessorção, de Placa Plana Simples, e de Difusão. Na globalidade, os resultados confirmaram que a pressão e o teor de etanol têm um efeito significativo sobre as curvas de extração, os rendimentos finais e as concentrações dos extratos, e mostraram a presença de limitações externas à transferência de massa em alguns ensaios. Mais uma vez, as famílias individuais de TTAs livres e acetilados apresentaram diferentes tendências de extracção. A modelação permitiu-nos confirmar não só o importante papel desempenhado pela difusão intraparticular na SFE, mas também a contribuição da resistência no filme em alguns ensaios. Após a análise de todos os resultados, foi efetuado um ensaio em duas etapas em série, possibilitando o enriquecimento do teor em TTAs no extracto devido às diferentes condições adotadas em cada etapa. Por último, um éster metílico de um ácido triterpénico do tipo oleanano - morolato de metilo - foi identificado pela primeira vez enquanto componente da casca de Eucalyptus na casca externa do Eucalyptus grandis x globulus, onde ocorre em teores elevados. A sua extração com CO2 supercrítico foi também realizada, visando a conceção de uma alternativa de extração ambientalmente benigna para este composto. A 200 bar e 60 ºC, a remoção do morolato de metilo atingiu um patamar às 6 h para 5.1 kg h-1 de CO2 / kg de casca. Em geral, e de forma semelhante à SFE da casca do E. globulus, os TTAs acetilados foram mais significativamente extraídos quando comparados com os seus ácidos livres, o que está diretamente relacionado com a natureza menos polar destas moléculas. O trabalho apresentado nesta tese é uma contribuição para a valorização de uma corrente de biomassa com baixo valor na indústria de pasta em duas vertentes complementares. Por um lado, aumentou o conhecimento da composição lipofílica das cascas de Eucalyptus spp. com interesse comercial para a produção de pasta, destacando o seu potencial enquanto fontes de ácidos triterpénicos. Por outro lado, foram desenvolvidos dois processos alternativos e facilmente integráveis numa fábrica de pasta para a sua exploração a partir da casca: um baseado em tecnologias convencionais bem estabelecidas a nível industrial, prevendo a sua aplicação a curto prazo, e um outro baseado na SFE, seguindo as tendências das futuras biorrefinarias.

Mathematical modelling of supercritical CO2 extraction of volatile oils from aromatic plants

The modelling of the experimental data of the extraction of the volatile oil from six aromatic plants (coriander, fennel, savoury, winter savoury, cotton lavender and thyme) was performed using five mathematical models, based on differential mass balances. In all cases the extraction was internal diffusion controlled and the internal mass transfer coefficienty (k(s)) have been found to change with pressure, temperature and particle size. For fennel, savoury and cotton lavender, the external mass transfer and the equilibrium phase also influenced the second extraction period, since k(s) changed with the tested flow rates. In general, the axial dispersion coefficient could be neglected for the conditions studied, since Peclet numbers were high. On the other hand, the solute-matrix interaction had to be considered in order to ensure a satisfactory description of the experimental data.

Heat transfer coefficients from Newtonian and non-Newtonian fluids flowing in laminar regime in a helical coil

This study aimed to carry out experimental work to obtain, for Newtonian and non-Newtonian fluids, heat transfer coefficients, at constant wall temperature as boundary condition, in fully developed laminar flow inside a helical coil. The Newtonian fluids studied were aqueous solutions of glycerol, 25%, 36%, 43%, 59% and 78% (w/w) and the non-Newtonian fluids aqueous solutions of carboxymethylcellulose (CMC), a polymer, with concentrations 0.1%, 0.2%, 0.3%, 0.4% and 0.6% (w/w) and aqueous solutions of xanthan gum (XG), another polymer, with concentrations 0.1% and 0.2% (w/w). According to the rheological study performed, the polymer solutions had shear thinning behavior and different values of elasticity. The helical coil used has internal diameter, curvature ratio, length and pitch, respectively: 0.004575 m, 0.0263, 5.0 m and 11.34 mm. The Nusselt numbers for the CMC solutions are, on average, slightly higher than those for Newtonian fluids, for identical Prandtl and generalized Dean numbers. As outcome, the viscous component of the shear thinning polymer tends to potentiate the mixing effect of the Dean cells. The Nusselt numbers of the XG solutions are significant lower than those of the Newtonian solutions, for identical Prandtl and generalized Dean numbers. Therefore, the elastic component of the polymer tends to diminish the mixing effect of the Dean cells. A global correlation, for Nusselt number as a function of Péclet, generalized Dean and Weissenberg numbers for all Newtonian and non-Newtonian solutions studied, is presented.

Project, modelling and simulation of air stripping columns for the treatment of groundwater contaminated with volatile organic compounds

Volatile organic compounds are a common source of groundwater contamination that can be easily removed by air stripping in columns with random packing and using a counter-current flow between the phases. This work proposes a new methodology for the column design for any particular type of packing and contaminant avoiding the necessity of a pre-defined diameter used in the classical approach. It also renders unnecessary the employment of the graphical Eckert generalized correlation for pressure drop estimates. The hydraulic features are previously chosen as a project criterion and only afterwards the mass transfer phenomena are incorporated, in opposition to conventional approach. The design procedure was translated into a convenient algorithm using C++ as programming language. A column was built in order to test the models used either in the design or in the simulation of the column performance. The experiments were fulfilled using a solution of chloroform in distilled water. Another model was built to simulate the operational performance of the column, both in steady state and in transient conditions. It consists in a system of two partial non linear differential equations (distributed parameters). Nevertheless, when flows are steady, the system became linear, although there is not an evident solution in analytical terms. In steady state the resulting system of ODE can be solved, allowing for the calculation of the concentration profile in both phases inside the column. In transient state the system of PDE was numerically solved by finite differences, after a previous linearization.

Practical software improve design and performance of a randomly packed air stripping column for removing volatile organic compounds from water

STRIPPING is a software application developed for the automatic design of a randomly packing column where the transfer of volatile organic compounds (VOCs) from water to air can be performed and to simulate it’s behaviour in a steady-state. This software completely purges any need of experimental work for the selection of diameter of the column, and allows a choice, a priori, of the most convenient hydraulic regime for this type of operation. It also allows the operator to choose the model used for the calculation of some parameters, namely between the Eckert/Robbins model and the Billet model for estimating the pressure drop of the gaseous phase, and between the Billet and Onda/Djebbar’s models for the mass transfer. Illustrations of the graphical interface offered are presented.

Impacts de l'écoulement souterrain sur la dégradation du pergélisol

Les changements climatiques mesurés dans le Nord-ouest canadien au cours du XXIe siècle entraînent une dégradation du pergélisol. Certaines des principales conséquences physiques sont la fonte de la glace interstitielle lors du dégel du pergélisol, l’affaissement du sol et la réorganisation des réseaux de drainage. L’effet est particulièrement marqué pour les routes bâties sur le pergélisol, où des dépressions et des fentes se créent de façon récurrente, rendant la conduite dangereuse. Des observations et mesures de terrain effectuées à Beaver Creek (Yukon) entre 2008 et 2011 ont démontré qu’un autre processus très peu étudié et quantifié dégradait le pergélisol de façon rapide, soit la chaleur transmise au pergélisol par l’écoulement souterrain. Suite aux mesures de terrain effectuées (relevé topographique, étude géotechnique du sol, détermination de la hauteur de la nappe phréatique et des chenaux d’écoulement préférentiels, température de l’eau et du sol, profondeur du pergélisol et de la couche active), des modèles de transfert de chaleur par conduction et par advection ont été produits. Les résultats démontrent que l’écoulement souterrain dans la couche active et les zones de talik contribue à la détérioration du pergélisol via différents processus de transfert de chaleur conducto-convectifs. L’écoulement souterrain devrait être pris en considération dans tous les modèles et scénarios de dégradation du pergélisol. Avec une bonne caractérisation de l’environnement, le modèle de transfert de chaleur élaboré au cours de la présente recherche est applicable dans d’autres zones de pergélisol discontinu.

Aprofitament de residus vegetals per a la concentració i separació d'ions metàl·lics de solucions aquoses

La adsorció sobre carbó actiu és un tractament habitual para a l'eliminació de metalls contaminants d'afluents aquosos. Amb la finalitat de reduir el cost dels tractament actuals s'està estudiant la utilització d'adsorbents de baix cost com a substituts dels sorbents convencionals que s'utilitzen usualment en els tractaments d'aigües. En aquesta tesi s'ha avaluat la possibilitat d'aprofitar diversos residus vegetals procedents de processos agrícoles o residus industrials, com a sorbents per a l'eliminació de metalls de solucions aquoses. En concret, el treball s'ha centrat en assolir dos grans objectius, primer de tot, conèixer la possibilitat d'utilitzar el pinyol d'oliva com a adsorbent de metalls divalents de solucions aquoses, com són el Cd(II), Cu(II), Ni(II) i Pb(II), i en segon lloc, avaluar la utilització de quatre residus vegetals (escorça de yohimbe, rapa de raïm, suro i pinyol d'oliva) per a l'extracció de Cr(VI) de solucions aquoses i utilitzar el residu vegetal més apropiat com a base per tal d'obtenir un nou sorbent, amb més bona morfologia per ser utilitzat en sistemes d'eliminació de Cr(VI) en continu. Les dades cinètiques d'adsorció es van tractar amb el model cinètic de pseudo-segon ordre, amb el que es van determinar la velocitat inicial d'adsorció dels metalls. Els models d'isotermes d'equilibri de Langmuir i Freundlich es van utilitzar per descriure els equilibris d'adsorció i calcular els paràmetres de les isotermes. En els assajos amb mescles binàries de metalls, els resultats es van tractar amb el model ampliat de Langmuir. En aquest treball s'ha determinat, primerament, que el pinyol d'oliva és un bon sorbent dels metalls divalents estudiats. S'ha determinat que l'adsorció dels metalls varia amb el pH de la solució i que la presència de sals en la solució provoca una davallada en l'adsorció. També es va determinar la competència en l'adsorció entre els metalls al realitzar assajos en mescles binàries. Amb els estudis d'extracció de Cr(VI) amb els quatre materials s'ha determinat que aquests vegetals poden adsorbir el Cr(VI) en solució, tot i que la rapa i la yohimbe són els materials que presenten unes capacitats d'adsorció més elevades. Les anàlisis amb espectroscòpia electrònica de Raig-X realitzats en la rapa de raïm i la yohimbe en contacte amb Cr(VI) varen demostrar la presència del metall en els dos estats d'oxidació, Cr(VI) i Cr(III), evidenciant la participació del mecanisme de reducció de Cr(VI) en l'adsorció del metall sobre els materials. Amb l'encapsulació de la rapa de raïm es va incrementar significativament la capacitat d'adsorció del metall respecta a la seva utilització en la forma original. Les dades experimentals es van tractar amb un model de difusió i es va determinar el coeficient de difusió en l'adsorció en el sorbent amb diferent percentatge de rapa en l'interior. Finalment s'han realitzat estudis preliminars d'adsorció de crom hexavalent en continu utilitzant columnes de petites dimensions farcides amb el sorbent format per boles de rapa encapsulada en alginat càlcic. En aquests assajos s'ha determinat l'efecte en l'adsorció de metall de diversos paràmetres d'operació, com la concentració inicial de metall, el cabal i l'alçada de llit. El model de transferència de matèria i difusió en columna emprat pel tractament de les dades experimentals va mostrar l'efecte de la concentració inicial i del cabal en els coeficients de difusió i transferència de matèria. El model BDST no va predir correctament el temps de servei en els diferents paràmetres d'operació experimentats a causa de la complexitat del procés d'adsorció. Amb aquests assajos preliminars s'han establert les bases de l'adsorció de Cr(VI) amb el nou sorbent en sistemes en continu amb la finalitat de realitzar estudis posteriors d'eliminació del metall en columnes de majors dimensions.

Theoretical and experimental approaches towards the determination of solute effective diffusivities in foods

The aim of this review paper is to present experimental methodologies and the mathematical approaches used to determine effective diffusivities of solutes in food materials. The paper commences by describing the diffusion phenomena related to solute mass transfer in foods and effective diffusivities. It then focuses on the mathematical formulation for the calculation of effective diffusivities considering different diffusion models based on Fick's second law of diffusion. Finally, experimental considerations for effective diffusivity determination are elucidated primarily based on the acquirement of a series of solute content versus time curves appropriate to the equation model chosen. Different factors contributing to the determination of the effective diffusivities such as the structure of food material, temperature, diffusion solvent, agitation, sampling, concentration and different techniques used are considered. (c) 2005 Elsevier Inc. All rights reserved.