The Deposition and Burning Characteristics During Slagging Co-Firing Coal and Wood: Modeling and Numerical Simulation

Numerical analysis was used to study the deposition and burning characteristics of combining co-combustion with slagging combustion technologies in this paper. The pyrolysis and burning kinetic models of different fuels were implanted into the WBSF-PCC2 (wall burning and slag flow in pulverized co-combustion) computation code, and then the slagging and co-combustion characteristicsespecially the wall burning mechanism of different solid fuels and their effects on the whole burning behavior in the cylindrical combustor at different mixing ratios under the condition of keeping the heat input samewere simulated numerically. The results showed that adding wood powder at 25% mass fraction can increase the temperature at the initial stage of combustion, which is helpful to utilize the front space of the combustor. Adding wood powder at a 25% mass fraction can increase the reaction rate at the initial combustion stage; also, the coal ignitability is improved, and the burnout efficiency is enhanced by about 5% of suspension and deposition particles, which is helpful for coal particles to burn entirely and for combustion devices to minimize their dimensions or sizes. The results also showed that adding wood powder at a proper ratio is helpful to keep the combustion stability, not only because of the enhancement for the burning characteristics, but also because the running slag layer structure can be changed more continuously, which is very important for avoiding the abnormal slag accumulation in the slagging combustor. The theoretic analysis in this paper proves that unification of co-combustion and slagging combustion technologies is feasible, though more comprehensive and rigorous research is needed.

A comparative study of thermolysis characteristics and kinetics of seaweeds and fir wood

Thermal analysis and thermolysis kinetics of three kinds of seaweeds and fir wood (M. glyptostriboides Huet Cheng), a kind of typical land plant, had been conducted. The results showed that thermal stability follows the order of Grateloupia filicina < Ulva lactuca < Dictyopteris divaricata < fir wood. A notable difference on heat flow between seaweeds and fir wood during thermolysis was that the former were mainly connected with exothermic processes at relatively lower temperature regimes. while the latter was connected with an apparent endotherm at a relatively higher temperature regime followed by a maximum exothermic peak. This suggested that the heat coupling might be realized if co-thermolysis of seaweeds and fir wood were carried out. The main devolatilization phase of each seaweed could be described by Avrami-Erofeev equation, which indicated that thermolysis of seaweeds follows the mechanism of random nucleation and nuclei growth, whereas that of fir wood by Z-L-T equation and its thermolysis mechanism was three-dimensional diffusion. The activation energies calculated for both seaweeds and fir wood increase as conversion increases. However, those for the former have wider distribution. (c) 2006 Elsevier Ltd. All rights reserved.

Short-term morphological changes after sand-digging during a sand sculpture activity

The morphology of the beach backshore and foreshore at Huiquan Bay, Qingdao, China, is characterized by a single intertidal sandbar system with a spring tide range of 4.59 m. The beach was measured with a laser total station of Leica TPS402. Contours of the beach were generated using data collected in March and November 2005. The survey method provided 2 mm measuring accuracy and 4-10 m horizontal spacing. The net accretion volume of the foreshore was about 11, 215 m(3) from March to November. After sand sculpture activity, the axis of the sand trough migrated onshore from about 3.5 m to 17.5 m on the foreshore beach in November. At the same time, the axis of the sandbar crest migrated onshore no more than 42.25 m on the northwest foreshore; and it migrated offshore no more than 23.75 m on the southeast foreshore. On the northwest and southeast foreshore beach, two strips of erosion areas with a thickness of 0-0.2 m appeared on the sandbar crest. Accretion occurred at the bottom of the sand trough with a thickness of similar to 0.2-0.6 m. The sandbar height decreased after sand sculpture activity, and it was no more than 0.7 m in March and 0.6 m in November. Human activities, such as sand digging on the sandbar crest during sand sculpture activity, also can disturb the beach morphology of intertidal bar systems. This phenomenon also was validated by comparison of beach morphology, the results of a color artificial tracer experiment and a sediment transportation trend prediction.

Lack of latitudinal trends in wood anatomy of Dodonaea viscosa (Sapindaceae), a species with a worldwide distribution

Latitudinal or altitudinal variation in several anatomical characters of wood is common for woody dicotyledonous genera with a wide distribution, but whether such variation exists at the species level is disputed. Latitudinal and altitudinal trends in wood anatomy of Dodonaea viscosa were studied, using 102 samples collected between 41.2degrees S and 33.3degrees N latitude and 7-2750 in altitude. We studied variation in four quantitative features: vessel element length, fiber length, vessel frequency, and tangential vessel diameter. Ontogenetic trends were minimal with a slight decrease or increase in the innermost stem and were negligible among the studied specimens. Throughout the distributional range of the species, no latitudinal trends were detected in either the Northern or Southern Hemispheres, Altitudinal trends were also nonexistent, except for two features in specimens from China and Japan. Absence of latitudinal or altitudinal trends in this widely distributed species suggests that in some species the species-level variation in wood anatomy is not controlled by ecological gradients.

Calorimetric study of Wood alloy

The heat capacities of Wood alloy have been measured with an automatic adiabatic calorimeter over the temperature range of 80 similar to 360 K. The thermodynamic data of solid-liquid phase transition have been obtained from the heat capacity measurements. The melting temperature, enthalpy and entropy of fusion of the substance are 345.662 K, 18.47 J.g(-1) and 0.05343 J.g(-1).K-1, respectively. The necessary thermal data are provided for the low temperature thermodynamic study of the alloy.

Creating religious place in Ireland: Hindu public places of worship and the Indian sculpture park

This paper examines the creation of religious place. It argues that the designation of a place as “religious” is a subjective and creative act which is dependent upon the perception and past, or memory, of the viewer. The paper focuses specifically on the creation of public places of worship by Hindu groups in the Dublin city area of Ireland and on the varied perceptions of the Indian Sculpture Park in County Wicklow. The creation of public places of worship results in places classified as “religious” due to the intention of the creator, the terminology used and the types of activities that take place in the space. This is in contrast to places such as the Indian Sculpture Park in County Wicklow which was created as a secular space but which is viewed by some Hindus as an outdoor temple due to the presence of sculptures of the Hindu deity Ganesh. Other Hindus do not view the space as having any religious significance and so its religiosity is contested. This points to the fact that the creation of religious place is a creative act of interpretation which is dependent upon the perception and past of the viewer and which changes over time.

The Effect of Wood Burial and Submersion on Decomposition: Implications for Reducing Carbon Emissions

Gemstone Team Carbon Sinks

Three Hundred Years in Annapolis: Phase III Archaeological Investigations of the Anne Arundel County Courthouse Site (18AP63), Annapolis, Maryland

During the summer of 1994, Archaeology in Annapolis conducted archaeological investigations of the city block bounded by Franklin, South and Cathedral Streets in the city of Annapolis. This Phase III excavation was conducted as a means to identify subsurface cultural resources in the impact area associated with the proposed construction of the Anne Arundel County Courthouse addition. This impact area included both the upper and lower parking lots used by Courthouse employees. Investigations were conducted in the form of mechanical trenching and hand excavated units. Excavations in the upper lot area yielded significant information concerning the interior area of the block. Known as Bellis Court, this series of rowhouses was constructed in the late nineteenth century and was used as rental properties by African-Americans. The dwellings remained until the middle of the twentieth century when they were demolished in preparation for the construction of a Courthouse addition. Portions of the foundation of a house owned by William H. Bellis in the 1870s were also exposed in this area. Construction of this house was begun by William Nicholson around 1730 and completed by Daniel Dulany in 1732/33. It was demolished in 1896 by James Munroe, a Trustee for Bellis. Excavations in the upper lot also revealed the remains of a late seventeenth/early eighteenth century wood-lined cellar, believed to be part of the earliest known structure on Lot 58. After an initially rapid deposition of fill around 1828, this cellar was gradually covered with soil throughout the remainder of the nineteenth century. The fill deposit in the cellar feature yielded a mixed assemblage of artifacts that included sherds of early materials such as North Devon gravel-tempered earthenware, North Devon sgraffito and Northem Italian slipware, along with creamware, pearlware and whiteware. In the lower parking lot, numerous artifacts were recovered from yard scatter associated with the houses that at one time fronted along Cathedral Street and were occupied by African- Americans. An assemblage of late seventeenth century/early eighteenth century materials and several slag deposits from an early forge were recovered from this second area of study. The materials associated with the forge, including portions of a crucible, provided evidence of some of the earliest industry in Annapolis. Investigations in both the upper and lower parking lots added to the knowledge of the changing landscape within the project area, including a prevalence of open space in early periods, a surprising survival of impermanent structures, and a gradual regrading and filling of the block with houses and interior courts. Excavations at the Anne Arundel County Courthouse proved this to be a multi-component site, rich in cultural resources from Annapolis' Early Settlement Period through its Modern Period (as specified by Maryland's Comprehensive Historic Preservation Plan (Weissman 1986)). This report provides detailed interpretations of the archaeological findings of these Phase III investigations.

The Daedalus system: A tool for the Italian investigating magistrate

Daedalus is a computer tool, developed by an Italian magistrate - Carmelo Asaro - and integrated in his own daily routine as an investigating magistrate conducting inquiries, then as a prosecutor if and when the case investigated goes to court. This tool has recently been adopted by magistrates in judiciary offices throughout Italy, spawning moreover other related projects. First, this paper describes a sample session with daedalus. Next, an overview of an array of judicial tools leads to positioning daedalus in the context of the spectrum.