System integration design in MEMS - A case study of micromachined load cell

One of the critical issues in large scale commercial exploitation of MEMS technology is its system integration. In MEMS, a system design approach requires integration of varied and disparate subsystems with one of a kind interface. The physical scales as well as the magnitude of signals of various subsystems vary widely. Known and proven integration techniques often lead to considerable loss in advantages the tiny MEMS sensors have to offer. Therefore, it becomes imperative to think of the entire system at the outset, at least in terms of the concept design. Such design entails various aspects of the system ranging from selection of material, transduction mechanism, structural configuration, interface electronics, and packaging. One way of handling this problem is the system-in-package approach that uses optimized technology for each function using the concurrent hybrid engineering approach. The main strength of this design approach is the fast time to prototype development. In the present work, we pursue this approach for a MEMS load cell to complete the process of system integration for high capacity load sensing. The system includes; a micromachined sensing gauge, interface electronics and a packaging module representing a system-in-package ready for end characterization. The various subsystems are presented in a modular stacked form using hybrid technologies. The micromachined sensing subsystem works on principles of piezo-resistive sensing and is fabricated using CMOS compatible processes. The structural configuration of the sensing layer is designed to reduce the offset, temperature drift, and residual stress effects of the piezo-resistive sensor. ANSYS simulations are carried out to study the effect of substrate coupling on sensor structure and its sensitivity. The load cell system has built-in electronics for signal conditioning, processing, and communication, taking into consideration the issues associated with resolution of minimum detectable signal. The packaged system represents a compact and low cost solution for high capacity load sensing in the category of compressive type load sensor.

e-SURAKSHAK: A Cyber-Physical Healthcare System with Service Oriented Architecture

In this paper we present the design of ``e-SURAKSHAK,'' a novel cyber-physical health care management system of Wireless Embedded Internet Devices (WEIDs) that sense vital health parameters. The system is capable of sensing body temperature, heart rate, oxygen saturation level and also allows noninvasive blood pressure (NIBP) measurement. End to end internet connectivity is provided by using 6LoWPAN based wireless network that uses the 802.15.4 radio. A service oriented architecture (SOA) 1] is implemented to extract meaningful information and present it in an easy-to-understand form to the end-user instead of raw data made available by sensors. A central electronic database and health care management software are developed. Vital health parameters are measured and stored periodically in the database. Further, support for real-time measurement of health parameters is provided through a web based GUI. The system has been implemented completely and demonstrated with multiple users and multiple WEIDs.

Métodos e técnicas de Design Centrado no Usuário: um levantamento a partir da usabilidade de produtos do CTIC/Fiocruz

A relação causal entre métodos de projeto e a usabilidade de produtos de comunicação e informação foi o tema desse estudo que buscou identificar o estado da arte sobre um processo de projeto que resulte em mais usabilidade na web. A partir dessa identificação, avaliou-se as melhorias que poderiam ser adotadas nos processos de desenvolvimento de interfaces utilizados por uma equipe específica da Fundação Oswaldo Cruz (CTIC - Fiocruz). Entendeu-se que um método de projeto deve estar atualizado em relação aos conhecimentos de áreas como a Ergonomia, a Interação Humano-computador e o Design de Interação. Para isso, adotou-se a hipótese de que o processo de projeto deve combinar três aspectos: a) um significativo envolvimento do usuário ao longo do processo; b) o uso de sucessivas iterações para configurar o produto e c) uma combinação mínima de técnicas relacionadas a objetivos específicos de cada fase de uma abordagem de Design Centrado no Usuário. Para contribuir com o desenvolvimento de métodos e técnicas que melhorem a usabilidade, descreveu-se as características dos métodos registrados na literatura e praticados por profissionais externos à Fundação Oswaldo Cruz (Fiocruz). A partir dessas informações, o estudo direcionou-se para o segundo objetivo específico: identificar melhorias nos métodos e técnicas aplicáveis no caso do CTIC Fiocruz. Através da combinação da revisão de literatura e da pesquisa de campo foram produzidas informações sobre tipos de fluxo dos métodos, tipos de envolvimento dos usuários, quantidade e gravidade de problemas de usabilidade observadas pelos profissionais e a validade de base geral de método para diferentes produtos. A primeira rodada de entrevista foi realizada para melhor entender o contexto da hipótese e a relação entre suas variáveis. A segunda rodada identificou as características do processo de projeto utilizado no CTIC. A partir dessas informações, aplicou-se duas técnicas com profissionais externos. Um questionário on-line foi utilizado para levantar informações bem específicas, em sua maioria de características quantitativas. A última técnica aplicada foi um card sorting on-line que apresentou um caso de projeto em que os profissionais indicaram quais técnicas seriam utilizadas diante de dois cenários diferentes: um mais favorável e outro restritivo. A análise demonstrou que a maioria dos profissionais acredita que os problemas de usabilidade são consequência da falta de determinadas abordagens e técnicas. Por isso, esses profissionais combinam fluxos iterativos com um significativo envolvimento do usuário no processo. Foram sugeridas melhorias para o método utilizado no CTIC sintetizadas através de um processo de Design Centrado no Usuário como ponto de partida que aplica o conceito tradicional de usabilidade (performance). Assim que possível, esse processo deve ser aperfeiçoado ao incluir o conceito de experiência do usuário que considera também os aspectos emocionais e hedonômicos na interação.

Design and Evaluation of a Retrofittable Electric Snow Melting System for Pavements

Gemstone Team SnowMelt

Massive MIMO with Non-Ideal Arbitrary Arrays: Hardware Scaling Laws and Circuit-Aware Design

Massive multiple-input multiple-output (MIMO) systems are cellular networks where the base stations (BSs) are equipped with unconventionally many antennas, deployed on colocated or distributed arrays. Huge spatial degrees-of-freedom are achieved by coherent processing over these massive arrays, which provide strong signal gains, resilience to imperfect channel knowledge, and low interference. This comes at the price of more infrastructure; the hardware cost and circuit power consumption scale linearly/affinely with the number of BS antennas N. Hence, the key to cost-efficient deployment of large arrays is low-cost antenna branches with low circuit power, in contrast to today’s conventional expensive and power-hungry BS antenna branches. Such low-cost transceivers are prone to hardware imperfections, but it has been conjectured that the huge degrees-of-freedom would bring robustness to such imperfections. We prove this claim for a generalized uplink system with multiplicative phasedrifts, additive distortion noise, and noise amplification. Specifically, we derive closed-form expressions for the user rates and a scaling law that shows how fast the hardware imperfections can increase with N while maintaining high rates. The connection between this scaling law and the power consumption of different transceiver circuits is rigorously exemplified. This reveals that one can make the circuit power increase as p N, instead of linearly, by careful circuit-aware system design.

Scalable Intelligence for Scheduling Systems

A personalização é um aspeto chave de uma interação homem-computador efetiva. Numa era em que existe uma abundância de informação e tantas pessoas a interagir com ela, de muitas maneiras, a capacidade de se ajustar aos seus utilizadores é crucial para qualquer sistema moderno. A criação de sistemas adaptáveis é um domínio bastante complexo que necessita de métodos muito específicos para ter sucesso. No entanto, nos dias de hoje ainda não existe um modelo ou arquitetura padrão para usar nos sistemas adaptativos modernos. A principal motivação desta tese é a proposta de uma arquitetura para modelação do utilizador que seja capaz de incorporar diferentes módulos necessários para criar um sistema com inteligência escalável com técnicas de modelação. Os módulos cooperam de forma a analisar os utilizadores e caracterizar o seu comportamento, usando essa informação para fornecer uma experiência de sistema customizada que irá aumentar não só a usabilidade do sistema mas também a produtividade e conhecimento do utilizador. A arquitetura proposta é constituída por três componentes: uma unidade de informação do utilizador, uma estrutura matemática capaz de classificar os utilizadores e a técnica a usar quando se adapta o conteúdo. A unidade de informação do utilizador é responsável por conhecer os vários tipos de indivíduos que podem usar o sistema, por capturar cada detalhe de interações relevantes entre si e os seus utilizadores e também contém a base de dados que guarda essa informação. A estrutura matemática é o classificador de utilizadores, e tem como tarefa a sua análise e classificação num de três perfis: iniciado, intermédio ou avançado. Tanto as redes de Bayes como as neuronais são utilizadas, e uma explicação de como as preparar e treinar para lidar com a informação do utilizador é apresentada. Com o perfil do utilizador definido torna-se necessária uma técnica para adaptar o conteúdo do sistema. Nesta proposta, uma abordagem de iniciativa mista é apresentada tendo como base a liberdade de tanto o utilizador como o sistema controlarem a comunicação entre si. A arquitetura proposta foi desenvolvida como parte integrante do projeto ADSyS - um sistema de escalonamento dinâmico - utilizado para resolver problemas de escalonamento sujeitos a eventos dinâmicos. Possui uma complexidade elevada mesmo para utilizadores frequentes, daí a necessidade de adaptar o seu conteúdo de forma a aumentar a sua usabilidade. Com o objetivo de avaliar as contribuições deste trabalho, um estudo computacional acerca do reconhecimento dos utilizadores foi desenvolvido, tendo por base duas sessões de avaliação de usabilidade com grupos de utilizadores distintos. Foi possível concluir acerca dos benefícios na utilização de técnicas de modelação do utilizador com a arquitetura proposta.

Exploration de l’expérience de tirer son lait par les mères : constats dans une optique de design

Le tire-lait est un appareil conçu pour aider les mères durant l’allaitement. Selon la recherche préliminaire effectuée, c’est un thème très peu exploré dans les études; il est donc difficile d’affirmer si le produit répond correctement aux besoins reliés à son usage et à son utilité ou comment il s’intègre dans l’allaitement. Les fondements de l’étude exploratoire ont été bâtis sur ces enjeux dans le but de comprendre l’expérience d’usage du tire-lait. Inspirée de l’approche phénoménologique centrée sur l’usager, l’étude a permis d’amasser des données qualitatives à travers des entrevues semi-dirigées auprès de sept participantes. L’analyse de ces données a permis d’identifier les thèmes importants qui ont mené à des constats, rédigés dans une optique de design. L’étude a trouvé que c’est souvent quand la réalité de l’allaitement au sein rattrape les mères qu’elles vont vouloir se procurer un tire-lait, en s’inspirant des marques utilisées dans les hôpitaux par manque de temps. Le tire-lait devient alors principalement utile pour se désengorger et pour la liberté qu’il procure, s’intégrant dans une routine. Le tire-lait est par contre peu ergonomique; il semble y avoir un décalage entre le concept proposé et les manipulations réelles, notamment au niveau de la mise en marche, des bouteilles et des embouts. Ces résultats de l’étude pourraient être intégrés dans le tire-lait pour mieux représenter la réalité du contexte, de la pratique et de l’usage du produit. Ils pourraient ainsi nourrir le processus de conception dans un projet futur afin d’améliorer le design du tire-lait.

Le design participatif au sein d’entreprises : une exploration des opportunités et limites perçues par des concepteurs de produits

La littérature contient une abondance d’information sur les approches de design impliquant les utilisateurs. Bien que les chercheurs soulèvent de nombreux avantages concernant ces approches, on en sait peu sur ce que les concepteurs des entreprises en pensent. Ce projet a pour but de connaître les perceptions des concepteurs de produits quant aux outils de design participatif puis, d’identifier les opportunités et limites qu’ils évoquent à ce sujet, et finalement, de faire des suggestions d’outils qui faciliteraient l’introduction du design participatif dans un processus de design existant. Après avoir fait un survol du domaine du design participatif et de ses outils, six cas sont étudiés au moyen d’entrevues semi-dirigées conduites auprès de concepteurs de produits. Les données sont analysées à l’aide de cartes cognitives. En ce qui concerne les outils de design participatif, les participants rencontrés perçoivent un accès direct aux besoins des utilisateurs et la possibilité de minimiser les erreurs en début de processus donc, d’éviter les modifications coûteuses qu’elles auraient entraînées. Les obstacles perçus par les concepteurs sont principalement liés à la résistance au changement, à la crainte de laisser créer ou décider les utilisateurs, ainsi qu’au manque de temps et de ressources de l’équipe. Finalement, sur la base des informations collectées, nous suggérons quatre outils de design participatif qui semblent plus intéressants : l’enquête contextuelle, les sondes, les tests de prototypes et l’approche « lead user ». Pour faire suite à ce travail, il serait intéressant d’élaborer un protocole de recherche plus exhaustif pour augmenter la portée des résultats, ou encore, d’appliquer le design participatif, dans une entreprise, afin d’explorer la satisfaction des gens quant aux produits conçus, les effets collatéraux sur les équipes impliquées, l’évolution des prototypes ou le déroulement des ateliers.

Rendre possible l’engagement en familiarité dans les CHSLD : les savoir-être d’une pratique de design centrée sur l’usager

Les défis associés au phénomène du vieillissement démographique de la population se manifestent sous plusieurs formes et à de nombreux égards. Il y a des questions générales comme celles qui touchent l’économique et d’autres, plus spécifiques et situées, comme celles des modalités assurant des services et des soins adéquats aux personnes vulnérables. Par exemple, le colloque « La qualité de l’expérience des usagers et des proches : vers la personnalisation des soins et des services sociaux », programmé dans le cadre des Entretiens Jacques Cartier à l’automne 2014, s’était donné comme objectif d’examiner l’expérience personnelle des usagers relativement aux prestations de soins de santé et à l’organisation des services sociaux. L’origine de ces réflexions réside dans la nécessité de trouver un meilleur équilibre des pouvoirs dans les relations d’aide ou la prestation de soin. Cette problématique sous-entend l’idée de rendre les usagers capables d’un certain contrôle par l’adoption d’approches permettant aux professionnels de faire des ajustements personnalisés. Cette thèse de doctorat s’inscrit directement dans le prolongement de cette problématique. La recherche vise à examiner les conditions en mesure de rendre possible, dans les Centres d’hébergement et de soins de longue durée (CHSLD), un rapport au monde catégorisé par ce que le sociologue Laurent Thévenot nomme le régime de la familiarité. Le régime de la familiarité fait référence aux réalités où l’engagement des personnes se déploie dans l’aisance. Autrement dit, ce régime d’engagement correspond à un rapport au milieu où la personne est en mesure de déployer ses habitudes, d’habiter le moment et de se sentir chez elle. Comme le montre Thévenot, ce type d’engagement commande la conception d’un monde qui offre aux personnes la possibilité d’articuler les modalités de leurs actions sur des repères qui font sens personnellement pour eux. Ainsi, l’objet de la recherche consiste à mieux comprendre la participation du design à la conception d’un milieu d’hébergement capable d’accueillir ce type d’engagement pragmatique. Les orientations associées à la conception de milieux d’hébergement capables de satisfaire de telles exigences correspondent largement aux ambitions qui accompagnent le développement des approches du design centrées sur l’usager, du design d’expériences et plus récemment du design empathique. Cela dit, malgré les efforts investis en ce sens, les capacités d’appropriation des usagers restent un problème pour lequel les réponses sont précaires. La thèse interroge ainsi le fait que les développements des approches de design, qui ont fait de l’expérience des usagers une préoccupation de premier plan, sont trop souvent restreints par des questions de méthodes et de procédures. Le développement de ces connaissances se serait fait au détriment de l’examen précis des savoir-être également nécessaires pour rendre les designers capables de prendre au sérieux les enjeux associés aux aspirations de ces approches. Plus spécifiquement, la recherche précise les qualités de l’expérience des établissements dont le design permet l’engagement en familiarité. L’enquête s’appuie sur une analyse des jugements posés par des équipes d’évaluation de la qualité du milieu de vie des CHSLD présents sur le territoire Montréalais. L’analyse a mené à la caractérisation de cinq qualités : l’accueillance, la convivialité, la flexibilité, la prévenance et la stabilité. Finalement, sous la forme d’un essai réflexif, un tableau de savoir-être est suggéré comme manière de rendre les designers capables de mettre en œuvre des milieux d’hébergement présentant les qualités identifiées. Cet essai est également l’occasion du développement d’un outil réflexif pour une pédagogie et une pratique vertueuse du design.

Modelling and simulation of a photovoltaic fuel cell hybrid system

A stand-alone power system is an autonomous system that supplies electricity to the user load without being connected to the electric grid. This kind of decentralized system is frequently located in remote and inaccessible areas. It is essential for about one third of the world population which are living in developed or isolated regions and have no access to an electricity utility grid. The most people live in remote and rural areas, with low population density, lacking even the basic infrastructure. The utility grid extension to these locations is not a cost effective option and sometimes technically not feasible. The purpose of this thesis is the modelling and simulation of a stand-alone hybrid power system, referred to as “hydrogen Photovoltaic-Fuel Cell (PVFC) hybrid system”. It couples a photovoltaic generator (PV), an alkaline water electrolyser, a storage gas tank, a proton exchange membrane fuel cell (PEMFC), and power conditioning units (PCU) to give different system topologies. The system is intended to be an environmentally friendly solution since it tries maximising the use of a renewable energy source. Electricity is produced by a PV generator to meet the requirements of a user load. Whenever there is enough solar radiation, the user load can be powered totally by the PV electricity. During periods of low solar radiation, auxiliary electricity is required. An alkaline high pressure water electrolyser is powered by the excess energy from the PV generator to produce hydrogen and oxygen at a pressure of maximum 30bar. Gases are stored without compression for short- (hourly or daily) and long- (seasonal) term. A proton exchange membrane (PEM) fuel cell is used to keep the system’s reliability at the same level as for the conventional system while decreasing the environmental impact of the whole system. The PEM fuel cell consumes gases which are produced by an electrolyser to meet the user load demand when the PV generator energy is deficient, so that it works as an auxiliary generator. Power conditioning units are appropriate for the conversion and dispatch the energy between the components of the system. No batteries are used in this system since they represent the weakest when used in PV systems due to their need for sophisticated control and their short lifetime. The model library, ISET Alternative Power Library (ISET-APL), is designed by the Institute of Solar Energy supply Technology (ISET) and used for the simulation of the hybrid system. The physical, analytical and/or empirical equations of each component are programmed and implemented separately in this library for the simulation software program Simplorer by C++ language. The model parameters are derived from manufacturer’s performance data sheets or measurements obtained from literature. The identification and validation of the major hydrogen PVFC hybrid system component models are evaluated according to the measured data of the components, from the manufacturer’s data sheet or from actual system operation. Then, the overall system is simulated, at intervals of one hour each, by using solar radiation as the primary energy input and hydrogen as energy storage for one year operation. A comparison between different topologies, such as DC or AC coupled systems, is carried out on the basis of energy point of view at two locations with different geographical latitudes, in Kassel/Germany (Europe) and in Cairo/Egypt (North Africa). The main conclusion in this work is that the simulation method of the system study under different conditions could successfully be used to give good visualization and comparison between those topologies for the overall performance of the system. The operational performance of the system is not only depending on component efficiency but also on system design and consumption behaviour. The worst case of this system is the low efficiency of the storage subsystem made of the electrolyser, the gas storage tank, and the fuel cell as it is around 25-34% at Cairo and 29-37% at Kassel. Therefore, the research for this system should be concentrated in the subsystem components development especially the fuel cell.

Virtual reality Post Traumatic Stress Disorder (PTSD) exposure therapy results with active duty Iraq war combatants

Post Traumatic Stress Disorder (PTSD) is reported to be caused by traumatic events that are outside the range of usual human experience including (but not limited to) military combat, violent personal assault, being kidnapped or taken hostage and terrorist attacks. Initial data suggests that at least 1 out of 6 Iraq War veterans are exhibiting symptoms of depression, anxiety and PTSD. Virtual Reality (VR) delivered exposure therapy for PTSD has been used with reports of positive outcomes. The aim of the current paper is to present the rationale and brief description of a Virtual Iraq PTSD VR therapy application and present initial findings from its use with PTSD patients. Thus far, Virtual Iraq consists of a series of customizable virtual scenarios designed to represent relevant Middle Eastern VR contexts for exposure therapy, including a city and desert road convoy environment. User-centered design feedback needed to iteratively evolve the system was gathered from returning Iraq War veterans in the USA and from a system deployed in Iraq and tested by an Army Combat Stress Control Team. Results from an open clinical trial at San Diego Naval Medical Center of the first 18 treatment completers indicate that 14 no longer meet PTSD diagnostic criteria at post-treatment, with only one not maintaining treatment gains at 3 month follow-up. Clinical tests are also currently underway at Ft. Lewis, Emory University, Weill Cornell Medical College, Walter Reed Army Medical Center and 10 other sites. Other sites are preparing to use the application for a variety of PTSD and VR research purposes.

Expert system aid for design of overload line distribution networks

The use of expert system techniques in power distribution system design is examined. The selection and siting of equipment on overhead line networks is chosen for investigation as the use of equipment such as auto-reclosers, etc., represents a substantial investment and has a significant effect on the reliability of the system. Through past experience with both equipment and network operations, most decisions in selection and siting of this equipment are made intuitively, following certain general guidelines or rules of thumb. This heuristic nature of the problem lends itself to solution using an expert system approach. A prototype has been developed and is currently under evaluation in the industry. Results so far have demonstrated both the feasibility and benefits of the expert system as a design aid.

Virtual reality Post Traumatic Stress Disorder (PTSD) exposure therapy results with active duty OIF/OEF service members

Posttraumatic stress disorder (PTSD) is reported to be caused by exposure to traumatic events including (but not limited to) military combat, violent personal assault, being kidnapped or taken hostage and terrorist attacks. Initial data suggest that at least 1 out of 6 Iraq War veterans are exhibiting symptoms of depression, anxiety and PTSD. Virtual reality (VR) delivered exposure therapy for PTSD has been used with reports of positive outcomes. The aim of the current paper, is to present the rationale and brief description of a Virtual Iraq/Afghanistan PTSD VR therapy application and present initial findings from its use with PTSD patients. Thus far, Virtual Iraq/Afghanistan consists of a series of customizable virtual scenarios designed to represent relevant Middle Eastern VR contexts for exposure therapy, including a city and desert road convoy environment. User-centered design feedback, needed to iteratively evolve the system, was gathered from returning Iraq War veterans in the USA and from a system deployed in Iraq and tested by an Army Combat Stress Control Team. Results from an open clinical trial at San Diego Naval Medical Center of the first 20 treatment completers indicate that 16 no longer met PTSD screening criteria at post-treatment, with only one not maintaining treatment gains at 3 month follow-up.

Design and management of sustainable built environments

The United Nation Intergovernmental Panel on Climate Change (IPCC) makes it clear that climate change is due to human activities and it recognises buildings as a distinct sector among the seven analysed in its 2007 Fourth Assessment Report. Global concerns have escalated regarding carbon emissions and sustainability in the built environment. The built environment is a human-made setting to accommodate human activities, including building and transport, which covers an interdisciplinary field addressing design, construction, operation and management. Specifically, Sustainable Buildings are expected to achieve high performance throughout the life-cycle of siting, design, construction, operation, maintenance and demolition, in the following areas: • energy and resource efficiency; • cost effectiveness; • minimisation of emissions that negatively impact global warming, indoor air quality and acid rain; • minimisation of waste discharges; and • maximisation of fulfilling the requirements of occupants’ health and wellbeing. Professionals in the built environment sector, for example, urban planners, architects, building scientists, engineers, facilities managers, performance assessors and policy makers, will play a significant role in delivering a sustainable built environment. Delivering a sustainable built environment needs an integrated approach and so it is essential for built environment professionals to have interdisciplinary knowledge in building design and management . Building and urban designers need to have a good understanding of the planning, design and management of the buildings in terms of low carbon and energy efficiency. There are a limited number of traditional engineers who know how to design environmental systems (services engineer) in great detail. Yet there is a very large market for technologists with multi-disciplinary skills who are able to identify the need for, envision and manage the deployment of a wide range of sustainable technologies, both passive (architectural) and active (engineering system),, and select the appropriate approach. Employers seek applicants with skills in analysis, decision-making/assessment, computer simulation and project implementation. An integrated approach is expected in practice, which encourages built environment professionals to think ‘out of the box’ and learn to analyse real problems using the most relevant approach, irrespective of discipline. The Design and Management of Sustainable Built Environment book aims to produce readers able to apply fundamental scientific research to solve real-world problems in the general area of sustainability in the built environment. The book contains twenty chapters covering climate change and sustainability, urban design and assessment (planning, travel systems, urban environment), urban management (drainage and waste), buildings (indoor environment, architectural design and renewable energy), simulation techniques (energy and airflow), management (end-user behaviour, facilities and information), assessment (materials and tools), procurement, and cases studies ( BRE Science Park). Chapters one and two present general global issues of climate change and sustainability in the built environment. Chapter one illustrates that applying the concepts of sustainability to the urban environment (buildings, infrastructure, transport) raises some key issues for tackling climate change, resource depletion and energy supply. Buildings, and the way we operate them, play a vital role in tackling global greenhouse gas emissions. Holistic thinking and an integrated approach in delivering a sustainable built environment is highlighted. Chapter two demonstrates the important role that buildings (their services and appliances) and building energy policies play in this area. Substantial investment is required to implement such policies, much of which will earn a good return. Chapters three and four discuss urban planning and transport. Chapter three stresses the importance of using modelling techniques at the early stage for strategic master-planning of a new development and a retrofit programme. A general framework for sustainable urban-scale master planning is introduced. This chapter also addressed the needs for the development of a more holistic and pragmatic view of how the built environment performs, , in order to produce tools to help design for a higher level of sustainability and, in particular, how people plan, design and use it. Chapter four discusses microcirculation, which is an emerging and challenging area which relates to changing travel behaviour in the quest for urban sustainability. The chapter outlines the main drivers for travel behaviour and choices, the workings of the transport system and its interaction with urban land use. It also covers the new approach to managing urban traffic to maximise economic, social and environmental benefits. Chapters five and six present topics related to urban microclimates including thermal and acoustic issues. Chapter five discusses urban microclimates and urban heat island, as well as the interrelationship of urban design (urban forms and textures) with energy consumption and urban thermal comfort. It introduces models that can be used to analyse microclimates for a careful and considered approach for planning sustainable cities. Chapter six discusses urban acoustics, focusing on urban noise evaluation and mitigation. Various prediction and simulation methods for sound propagation in micro-scale urban areas, as well as techniques for large scale urban noise-mapping, are presented. Chapters seven and eight discuss urban drainage and waste management. The growing demand for housing and commercial developments in the 21st century, as well as the environmental pressure caused by climate change, has increased the focus on sustainable urban drainage systems (SUDS). Chapter seven discusses the SUDS concept which is an integrated approach to surface water management. It takes into consideration quality, quantity and amenity aspects to provide a more pleasant habitat for people as well as increasing the biodiversity value of the local environment. Chapter eight discusses the main issues in urban waste management. It points out that population increases, land use pressures, technical and socio-economic influences have become inextricably interwoven and how ensuring a safe means of dealing with humanity’s waste becomes more challenging. Sustainable building design needs to consider healthy indoor environments, minimising energy for heating, cooling and lighting, and maximising the utilisation of renewable energy. Chapter nine considers how people respond to the physical environment and how that is used in the design of indoor environments. It considers environmental components such as thermal, acoustic, visual, air quality and vibration and their interaction and integration. Chapter ten introduces the concept of passive building design and its relevant strategies, including passive solar heating, shading, natural ventilation, daylighting and thermal mass, in order to minimise heating and cooling load as well as energy consumption for artificial lighting. Chapter eleven discusses the growing importance of integrating Renewable Energy Technologies (RETs) into buildings, the range of technologies currently available and what to consider during technology selection processes in order to minimise carbon emissions from burning fossil fuels. The chapter draws to a close by highlighting the issues concerning system design and the need for careful integration and management of RETs once installed; and for home owners and operators to understand the characteristics of the technology in their building. Computer simulation tools play a significant role in sustainable building design because, as the modern built environment design (building and systems) becomes more complex, it requires tools to assist in the design process. Chapter twelve gives an overview of the primary benefits and users of simulation programs, the role of simulation in the construction process and examines the validity and interpretation of simulation results. Chapter thirteen particularly focuses on the Computational Fluid Dynamics (CFD) simulation method used for optimisation and performance assessment of technologies and solutions for sustainable building design and its application through a series of cases studies. People and building performance are intimately linked. A better understanding of occupants’ interaction with the indoor environment is essential to building energy and facilities management. Chapter fourteen focuses on the issue of occupant behaviour; principally, its impact, and the influence of building performance on them. Chapter fifteen explores the discipline of facilities management and the contribution that this emerging profession makes to securing sustainable building performance. The chapter highlights a much greater diversity of opportunities in sustainable building design that extends well into the operational life. Chapter sixteen reviews the concepts of modelling information flows and the use of Building Information Modelling (BIM), describing these techniques and how these aspects of information management can help drive sustainability. An explanation is offered concerning why information management is the key to ‘life-cycle’ thinking in sustainable building and construction. Measurement of building performance and sustainability is a key issue in delivering a sustainable built environment. Chapter seventeen identifies the means by which construction materials can be evaluated with respect to their sustainability. It identifies the key issues that impact the sustainability of construction materials and the methodologies commonly used to assess them. Chapter eighteen focuses on the topics of green building assessment, green building materials, sustainable construction and operation. Commonly-used assessment tools such as BRE Environmental Assessment Method (BREEAM), Leadership in Energy and Environmental Design ( LEED) and others are introduced. Chapter nineteen discusses sustainable procurement which is one of the areas to have naturally emerged from the overall sustainable development agenda. It aims to ensure that current use of resources does not compromise the ability of future generations to meet their own needs. Chapter twenty is a best-practice exemplar - the BRE Innovation Park which features a number of demonstration buildings that have been built to the UK Government’s Code for Sustainable Homes. It showcases the very latest innovative methods of construction, and cutting edge technology for sustainable buildings. In summary, Design and Management of Sustainable Built Environment book is the result of co-operation and dedication of individual chapter authors. We hope readers benefit from gaining a broad interdisciplinary knowledge of design and management in the built environment in the context of sustainability. We believe that the knowledge and insights of our academics and professional colleagues from different institutions and disciplines illuminate a way of delivering sustainable built environment through holistic integrated design and management approaches. Last, but not least, I would like to take this opportunity to thank all the chapter authors for their contribution. I would like to thank David Lim for his assistance in the editorial work and proofreading.

Using virtual environments for trigger identification in addiction treatment

This paper presents a novel application of virtual environments to assist in encouraging behavior change in individuals who misuse drugs or alcohol. We describe the user-centered design of a series of scenes to engage users in the identification of triggers and to encourage discussions about relevant coping skills. Results from the initial testing of this application with six service users showed variation in user responses. Results also suggested that the system should encourage group discussion and that it was linked to a small improvement in users’ confidence in understanding and identifying triggers.