THEORETICAL ROAD DAMAGE DUE TO DYNAMIC TYRE FORCES OF HEAVY VEHICLES. PART 1: DYNAMIC ANALYSIS OF VEHICLES AND ROAD SURFACES.

Theory is presented for simulating the dynamic wheel forces generated by heavy road vehicles and the resulting dynamic response of road surfaces to these loads. Sample calculations are provided and the vehicle simulation is validated with data from full-scale tests. The methods are used in the accompanying paper to simulate the road damage done by a tandem-axle vehicle.

THEORETICAL ROAD DAMAGE DUE TO DYNAMIC TYRE FORCES OF HEAVY VEHICLES. PART 2: SIMULATED DAMAGE CAUSED BY A TANDEM-AXLE VEHICLE.

The literature relating to road surface failure and design is briefly reviewed and the conventional methods for assessing the road damaging effects of dynamic tire forces are examined. A new time domain technique for analyzing dynamic tire forces and four associated road damage criteria are presented. The force criteria are used to examine the road damaging characteristics of a simple tandem-axle vehicle model for a range of speed and road roughness conditions. It is concluded that for the proposed criteria, the theoretical service life of road surfaces that are prone to fatigue failure may be reduced significantly by the dynamic component of wheel forces. The damage done to approximately five per cent of the road surface area during the passage of a theoretical model vehicle at typical highway speeds may be increased by as much as four times.

A model for the erosive wear of rubber at oblique impact angles

A model has been developed to predict the erosive wear behaviour of elastomers under conditions of glancing impact by small hard particles. Previous work has shown the erosive wear mechanism of elastomers under these conditions to be similar in nature to that of abrasive wear by a sharp blade. The model presented here was developed from the model of Southern and Thomas for sliding abrasion, by combining their treatment of the growth of surface cracks with a model for particle impact in which the force - displacement relationship for an idealized flat-ended punch on a semi-infinite elastic solid was assumed. In this way an expression for the erosive wear rate was developed, and compared with experimental measurements of wear rate for natural rubber, styrene - butadiene rubber and a highly crosslinked polybutadiene rubber. Good qualitative agreement was found between the predictions of the model and the experimental measurements. The variation of erosion rate with impact velocity, impact angle, particle size, elastic modulus of the material, coefficient of friction and fatigue properties were all well accounted for. Quantitative agreement was less good, and the effects of erosive particle shape could not be accounted for. The reasons for these discrepancies are discussed. © 1992 IOP Publishing Ltd.

Road damage due to dynamic tyre forces measured on a public road

This paper describes a series of tests conducted on a UK trunk road, in which the dynamic tyre forces generated by over 1500 heavy goods vehicles (HGVs) were measured using a load measuring mat containing 144 capacitive strip sensors. The data was used to investigate the relative road damaging potential of the various classes of vehicles, and the degree of spatial repeatability of tyre forces present in a typical highway fleet. Approximately half the vehicles tested were found to contribute to a spatially repeatable pattern of pavement loading. On average, air suspended vehicles were found to generate lower dynamic load coefficients than steel suspended vehicles. However, air suspended vehicles also generated higher mean levels of theoretical road damage (aggregate force) than steel suspended vehicles, indicating that the ranking of suspensions depends on the pavement damage criterion used.

An integrated model of rolling tyre vibrations on a smooth road

We describe new results on the vibrations of rolling tyres, aimed at noise prediction for tyres of given design on a smooth road surface. This new approach incorporates our existing models, of smooth road-tyre interaction and belt vibration but includes additional features that are required for real tyre patterns. To this end, the model allows variable tread block size and grooves along the belt circumference; the density and angle of these grooves may also vary laterally. The key innovation is to treat the tyre belt as a laterally stacked series of rings, each of which is equipped with a set of viscoelastic springs around its circumference. It is shown how to use this construction to mimic the details of actual tyre patterns and, in conjunction with existing models, predict belt vibrations. The construction is applied to develop a ring discretisation for a real tyre that shows strong lateral variations. It is shown that the vibration amplitude is concentrated on a set of parallel lines in frequency-wavenumber space and that the tread pattern dictates the occurrence and spacing of these lines. Linkage to a boundary element calculation then allows quantification of the influence of tread parameters on radiated noise. Keywords: Vibration, tread pattern, tyre noise. Copyright © (2011) by the Institute of Noise Control Engineering.