Gamma-irradiation effects on Ce-doped YAG crystals grown by Cz and TGT method

Gamma-rays radiation effects on Ce:YAG crystals grown by Czochralski (Cz) and temperature gradient techniques (TGT) have been studied by means of optical absorption and luminescence spectra. Valence of Ce3+ ion changes during the gamma-ray irradiation process and this result indicates Ce4+ ion may exist in both Cz-Ce:YAG and TGT-Ce:YAG crystals. Thermally stimulated luminescence measurements reveal intense thermoluminescence peaks in gamma-irradiated Ce:YAG crystals and trap parameters were calculated by general-order kinetics expression. (C) 2006 Elsevier B.V. All rights reserved.

晶格匹配氮化镓和氧化锌基外延薄膜衬底材料ScAlMgO4晶体生长研究

采用提拉法成功生长了氮化镓和氧化锌基外延薄膜晶格匹配的ScAlMgO4单晶衬底材料,晶体呈透明白色,尺寸为Ф30mm×59mm,表面部分沿解理面有裂纹.粉末X射线衍射（XRD）分析表明经1400℃固相反应烧结的原料基本合成了ScAlMgO4多晶相.初步的偏光显微镜观察、晶体的粉末XRD表征、透过光谱和双晶摇摆测试表明晶体具有较好的光学性质和结晶质量.研究表明晶体本身的层状结构、较大的温度梯度和热应力的不均匀性是生长过程中引起晶体开裂的几个主要原因.

温度梯度法生长Nd：YAG激光晶体的核心分布

用温度梯度法生长了直径为75mm大尺寸的Nd：YAG激光晶体，通过退火排除了生长过程中进入晶体的碳原子．用正交偏光显微镜观察了晶体的核心分布以及生长条纹．测试了室温下的吸收谱并利用吸收谱研究了Nd离子在YAG晶体中的分布．比较了温度梯度法与提拉法生长晶体的区别．

ScAlMgO_4晶体的生长缺陷

采用提拉法生长出φ30 mm×55 mm的ScAlMgO4晶体。在晶体生长过程中有轻微的挥发,粉末X射线衍射分析表明:挥发物质为MgO单相。运用扫描电镜、光学显微镜以及高分辨X射线衍射仪对晶体中的包裹物、开裂、生长条纹和小角晶界缺陷进行了研究。结果表明:温度梯度和热应力是形成晶体中缺陷的主要原因。通过合理设计温场,控制固-液界面的形状及冷却过程的降温速率,可以提高晶体的完整性。

导模法和温度梯度法生长r面蓝宝石(英文)

r面(0112)蓝宝石晶体可用作制备非极性GaN薄膜的衬底。采用温度梯度法(temperature gradient technique,TGT)和导模法(edge-defined film-fed crystal growth,EFG)生长了质量良好的r面蓝宝石晶体。利用双晶衍射、光学显微镜、光谱仪观察和分析了晶体的结构和缺陷。结果表明:TGT法生长的r蓝宝石晶体的双晶摇摆曲线对称性好,半高宽值仅为18 rad.s,位错密度为4×103 cm-2,透过率达83%,晶体质量好。与TGT法相比,EFG法生长的r面蓝宝石晶体的结构完整性较差,位错密度为5×105 cm-2,透过率仅为75%。但是EFG法具有晶体生长速度快,后期加工成本低的优点。

Influence of carbon on the thermoluminescence and optically stimulated luminescence of α -Al2O3:C crystals

alpha-Al2O3:C crystal shows excellent thermoluminescence (TL) and optically stimulated luminescence (OSL) properties but the real role carbon plays in this crystal is still not clearly understood so far. In this work, alpha-Al2O3:C crystal doping with different amounts of carbon were grown by the temperature gradient technique, and TL and OSL properties of as-grown crystals were investigated. Additionally, a mechanism was proposed to explain the role of carbon in forming the TL and OSL properties of alpha-Al2O3:C. TL and OSL intensities of as-grown crystals increase with the increasing amount of carbon doping in the crystal, but no shift is found in the glow peak location at 465 K. As the amount of carbon doping in the crystals decreases, OSL decay rate becomes faster. With the increase in heating rate, the integral TL response of as-grown crystals decreases and glow peak shifts to higher temperatures. TL response decrease rate increases with the increasing amount of carbon doping in the crystals. All the TL and OSL response curves of as-grown crystals show linear-sublinear-saturation characteristic, and OSL dose response exhibits higher sensitivity and wider linear dose range than that of TL. The crystal doping with 5000 ppm carbon shows the best dosimetric properties. Carbon plays the role of a dopant in alpha-Al2O3:C crystal and four-valent carbon anions replace the two-valent anions of oxygen during the crystal growth process, and large amounts of oxygen vacancies were formed, which corresponds to the high absorption coefficient of F and F+ centers in the crystals.

α-Al_2O_3:C晶体的热释光和光释光特性

以高纯α-Al2O3和石墨为原料,采用温梯法生长了α-Al2O3:C晶体,使用RisΦTL/OSL-DA-15型热释光和光释光仪研究了其热释光和光释光特性.α-Al2O3:C晶体在462K附近有单一热释光峰,发射波长位于410nm.随着辐照剂量的增加,热释光强度逐渐增强,462K的热释光特征峰位置保持不变.α-Al2O3:C晶体的光释光衰减曲线由快衰减和慢衰减两个部分组成,随着辐照剂量的增加,快衰减部分衰减速率变化不大,而慢衰减部分衰减速率加快.在5×10-6—10Gy剂量范围内,α-Al2O3:C晶体的热释光剂量响应呈现良好的线性关系,30Gy时达到饱和;光释光剂量响应在5×10-6—60Gy剂量范围内呈现良好的线性关系,100Gy时达到饱和.与热释光相比,光释光剂量响应具有更高的灵敏度和更宽的线性剂量响应范围.

Growth of alpha-Al2O3:C crystal with highly sensitive optically stimulated luminescence

In this work. an alpha-Al2O3:C crystal was directly grown by the temperature gradient technique (TGT) using Al2O3 and graphite powders as the raw materials. The optical, optically stimulated luminescence (OSL) properties and dosimetric characteristics of as-grown crystal were investigated. As-grown alpha-Al2O3:C crystal shows strong absorption band at 205, 230 and 256 nm. Three-dimensional thermoluminescence (TL) emission spectrum of the crystal shows a single emission peak at similar to 415 nm. The OSL decay curve can be fitted to two exponentials, the faster component and the slower component. The OSL response of the crystal shows a linear-sublinear-saturation characteristic. As-grown alpha-Al2O3:C crystal shows excellent linearity in the dose range from 5 x 10(-6) to 50 Gy. For doses higher than the saturation dose (100 Gy). the OSL sensitivity decreases as the dose increases. Crown Copyright (C) 2008 Published by Elsevier B.V. All rights reserved.

Study of Al2O3/MgF2 HR coatings at 355 nm

With the present work we tried to study the effective methods to improve the laser-induced damage threshold (LIDT) and reflectance of HR coatings at 355 nm. The work presented in this paper wits part of an ongoing study about vacuum annealing. It was dedicated to study the effects Of Vacuum annealing with different temperature gradients on the structure, optical properties and laser-induced damage threshold (LIDT) of 355nm Al2O3/MgF2HR coatings. A number of samples were prepared by electron beam evaporation using the same deposition process with an optimal deposition temperature of 280 degrees C. After deposition, samples were annealed in the coating chamber for 3 h with different temperature gradients. Morphologies of the samples were observed by Leica-DMRXE. Microscope, Structure of the samples had been characterized by X-ray diffraction (XRD). Transmittance and reflectance of the samples were measured by Lambda 900 Spectrometer, The LIDT of the samples was measured by a 355 nm Nd:YAG laser with a pulse width of 8 ns. It was found that the temperature gradient of vacuum annealing had significant effects on the morphology, structure, absorption, and LIDT of the samples, (c) 2005 Elsevier Ltd. All rights reserved.

Thermodynamic damage mechanism of transparent films caused by a low-power laser

A new model for analyzing the laser-induced damage process is provided. In many damage pits, the melted residue can been found. This is evidence of the phase change of materials. Therefore the phase change of materials is incorporated into the mechanical damage mechanism of films. Three sequential stages are discussed: no phase change, liquid phase change, and gas phase change. To study the damage mechanism and process, two kinds of stress have been considered: thermal stress and deformation stress. The former is caused by the temperature gradient and the latter is caused by high-pressure drive deformation. The theory described can determine the size of the damage pit. (c) 2006 Optical Society of America.

Aplicações do formalismo de Keldysh ao transporte e ao bombeamento de calor em nanoestruturas

Num regime balísstico e a baixas temperaturas, a fórmula de Landauer dá uma boa descrição do transporte de calor para nano-junções conectadas a dois fios acoplados a banhos térmicos a temperaturas diferentes. Partindo de um modelo microscópico e utilizando o método de funções de Green fora do equilíbrio, é possível obter uma expressão para a condutância térmica na nano-junção equivalente a fórmula de Landauer. Esta depende dos valores das constantes de acoplamento entre os modos de fônons da região central e dos fios, além do gradiente térmico. A expressão para a condutância térmica é muito semelhante aquela obtida para a condutância elétrica. Neste trabalho nós apresentamos o método para o cálculo de grandezas relacionadas ao transporte térmico em um regime onde não há um gradiente de temperatura entre os reservatórios mas o sistema sofre uma perturbação dependente do tempo. Ou seja, com uma escolha conveniente da parametrização temporal dos termos de acoplamento entre a nano-junção e os fios é possível produzir uma corrente de calor na ausência de diferença de temperaturas entre os banhos térmicos aos quais os fios estão conectados. Esse fenômeno caracteriza o bombeamento de calor. Desenvolvemos uma teoria de transporte dependente do tempo para descrever o bombeamento. A teoria é geral, dependendo da densidade de fônons, da intensidade e dependência temporal do acoplamento. Aplicamos o formalismo em um modelo simples demonstrando que, em princípio, é possível bombear calor através de uma cadeia linear de átomos sem gradiente térmico.

黑龙江嘉荫地区古新世孢粉植物群及古植被、古气候研究

植物是环境变化的重要指示物之一。晚白垩至早第三纪时期，全球生态系统发生了剧烈变化，研究这一时期植物对了解地质历史时期环境变化趋势, 认识和保护当今环境有重要意义。我国黑龙江省嘉荫县有这一时期的地层发育，其中乌云煤矿和白山头是主要的露头剖面。前人曾从地质时代、孢粉及植物化石角度对这两个剖面进行过研究，但是仍有部分问题尚存争议。在本项工作中，我们对两个剖面的孢粉样品进行了系统采样，部分孢粉类型同时在光镜和电镜下进行了拍照。我们还对存在争议的这两个剖面的地质时代进行了讨论。同时，首次用共存分析法对这两个剖面的在沉积时期的气候进行了整体及分段的定量重建。另外，我们结合中其它地点的气候重建工作对不同时期的纬度温度梯度进行了研究。 乌云煤矿和白山头两个乌云组剖面的古新世孢粉植物群的研究结果表明：乌云煤矿孢粉植物群主要是与榛属（Corylus），桤木属（Alnus），桦木属（Betula），榆属（Ulmus）及松属（Pinus）有亲缘关系的植物；白山头剖面的孢粉植物类型与乌云煤矿基本一致，但是其中针叶类植物的花粉所占比重较大。 根据乌云煤矿与白山头剖面的孢粉类型在地层中的分布，以及与其它古新世地层的对比，我们认为乌云煤矿与白山头含孢粉段的地质时代为古新世。 用共存分析法得到乌云组古新世气候参数有两组。孢粉类型的共存结果为：年均温14.8-14.9℃，年降水量816-1389mm；植物化石类型的共存结果为：年均温16.3-16.8℃, 年降水：1124-1623mm。对乌云煤矿与白山头两个剖面孢粉带中的孢粉类型的气候参数分别进行共存，结果表明，除乌云煤矿孢粉第三带到第四带外，乌云地区的年均温在整个沉积时期均呈上升趋势；年均降水量的变化趋势与年均温基本一致。 根据从古新世到现代不同地点气候定量重建的年均温参数，我们计算得到了不同时期纬度温度梯度变化的值：<0.1℃/古纬度（古新世）、 0.1℃/古纬度（始新世）、0.45℃/纬度（中新世）、0.55℃/纬度（上新世）。结合当今全球的平均温度梯度值（0.7℃/纬度），我们得出纬度温度梯度的值从古新世以来呈不断上升的趋势。这一结果显示65Ma 以来赤道与极地间的温度差异逐渐增大，同时也提示了全球温度可能呈下降趋势。

On the trend of prawn catch off Paradeep

The distribution and landings of important varieties of prawns off Paradeep coast, Orissa, in relation to the climatic and hydrographic conditions from 1970-1976 are presented. The prawn fishery as a whole, showed a quadrennial cycle along the coast. The post-monsoon migration of all varieties of prawns along the coast directly depends on the annual precipitation. Temperature gradient, fluctuations in salinity and southerly wind in the Bay of Bengal influence the migration of the different species of prawns.

Operational Optimization of GaN Thin Film Growth Employing Numerical Simulation in a Showerhead MOCVD Reactor

A detailed reaction-tran sport model was studied in a showerhead reactor for metal organic chemical vapor deposition of GaN film by using computational fluid dynamics simulation. It was found that flat flow lines without swirl are crucial to improve the uniformity of the film growth, and thin temperature gradient above the suscptor can increase the film deposition rate. By above-mentioned research, we can employ higher h (the distance from the susceptor to the inlet), P (operational pressure) and the rate of susceptor rotation to improve the film growth.