Study of the mechanisms of shear transfer in fiber-reinforced concrete elements

matlab functions for the validation of push-off tests results

Influence of advanced load simulation models on fatigue design of jackets for offshore wind turbines.

Constant developments in the field of offshore wind energy have increased the range of water depths at which wind farms are planned to be installed. Therefore, in addition to monopile support structures suitable in shallow waters (up to 30 m), different types of support structures, able to withstand severe sea conditions at the greater water depths, have been developed. For water depths above 30 m, the jacket is one of the preferred support types. Jacket represents a lightweight support structure, which, in combination with complex nature of environmental loads, is prone to highly dynamic behavior. As a consequence, high stresses with great variability in time can be observed in all structural members. The highest concentration of stresses occurs in joints due to their nature (structural discontinuities) and due to the existence of notches along the welds present in the joints. This makes them the weakest elements of the jacket in terms of fatigue. In the numerical modeling of jackets for offshore wind turbines, a reduction of local stresses at the chord-brace joints, and consequently an optimization of the model, can be achieved by implementing joint flexibility in the chord-brace joints. Therefore, in this work, the influence of joint flexibility on the fatigue damage in chord-brace joints of a numerical jacket model, subjected to advanced load simulations, is studied.

Advanced mechanics of materials with microstructure

The study of advanced materials aimed at improving human life has been performed since time immemorial. Such studies have created everlasting and greatly revered monuments and have helped revolutionize transportation by ushering the age of lighter–than–air flying machines. Hence a study of the mechanical behavior of advanced materials can pave way for their use for mankind’s benefit. In this school of thought, the aim of this dissertation is to broadly perform two investigations. First, an efficient modeling approach is established to predict the elastic response of cellular materials with distributions of cell geometries. Cellular materials find important applications in structural engineering. The approach does not require complex and time-consuming computational techniques usually associated with modeling such materials. Unlike most current analytical techniques, the modeling approach directly accounts for the cellular material microstructure. The approach combines micropolar elasticity theory and elastic mixture theory to predict the elastic response of cellular materials. The modeling approach is applied to the two dimensional balsa wood material. Predicted properties are in good agreement with experimentally determined properties, which emphasizes the model’s potential to predict the elastic response of other cellular solids, such as open cell and closed cell foams. The second topic concerns intraneural ganglion cysts which are a set of medical conditions that result in denervation of the muscles innervated by the cystic nerve leading to pain and loss of function. Current treatment approaches only temporarily alleviate pain and denervation which, however, does not prevent cyst recurrence. Hence, a mechanistic understanding of the pathogenesis of intraneural ganglion cysts can help clinicians understand them better and therefore devise more effective treatment options. In this study, an analysis methodology using finite element analysis is established to investigate the pathogenesis of intraneural ganglion cysts. Using this methodology, the propagation of these cysts is analyzed in their most common site of occurrence in the human body i.e. the common peroneal nerve. Results obtained using finite element analysis show good correlation with clinical imaging patterns thereby validating the promise of the method to study cyst pathogenesis.

Experimental and Analytical Study of Masonry Infill Reinforced Concrete Frames Retrofitted with Steel Braces

In the present work a seismic retrofitting technique is proposed for masonry infilled reinforced concrete frames based on the replacement of infill panels by K-bracing with vertical shear link. The performance of this technique is evaluated through experimental tests. A simplified numerical model for structural damage evaluation is also formulated according to the notions and principles of continuum damage mechanics. The proposed model is calibrated with the experimental results. The experimental results have shown an excellent energy dissipation capacity with the proposed technique. Likewise, the numerical predictions with the proposed model are in good agreement with experimental results.

QL-CONST1: an expert system for quality level prediction in concrete structures

Current trends in the fields of artifical intelligence and expert systems are moving towards the exciting possibility of reproducing and simulating human expertise and expert behaviour into a knowledge base, coupled with an appropriate, partially ‘intelligent’, computer code. This paper deals with the quality level prediction in concrete structures using the helpful assistance of an expert system, QL-CONST1, which is able to reason about this specific field of structural engineering. Evidence, hypotheses and factors related to this human knowledge field have been codified into a knowledge base. This knowledge base has been prepared in terms of probabilities of the presence of either hypotheses or evidence and the conditional presence of both. Human experts in the fields of structural engineering and the safety of structures gave their invaluable knowledge and assistance to the construction of the knowledge base. Some illustrative examples for, the validation of the expert system behaviour are included.

Influence of the Second Flexural Mode on the Response of High-Speed Bridges

This paper deals with the assessment of the contribution of the second flexural mode to the dynamic behaviour of simply supported railway bridges. Alluding to the works of other authors, it is suggested in some references that the dynamic behaviour of simply supported bridges could be adequately represented taking into account only the contribution of the fundamental flexural mode. On the other hand, the European Rail Research Institute (ERRI) proposes that the second mode should also be included whenever the associated natural frequency is lower than 30 Hz]. This investigation endeavours to clarify the question as much as possible by establishing whether the maximum response of the bridge, in terms of displacements, accelerations and bending moments, can be computed accurately not taking account of the contribution of the second mode. To this end, a dimensionless formulation of the equations of motion of a simply supported beam traversed by a series of equally spaced moving loads is presented. This formulation brings to light the fundamental parameters governing the behaviour of the beam: damping ratio, dimensionless speed $ \alpha$=VT/L, and L/d ratio (L stands for the span of the beam, V for the speed of the train, T represents the fundamental period of the bridge and d symbolises the distance between consecutive loads). Assuming a damping ratio equal to 1%, which is a usual value for prestressed high-speed bridges, a parametric analysis is conducted over realistic ranges of values of $ \alpha$ and L/d. The results can be extended to any simply supported bridge subjected to a train of equally spaced loads in virtue of the so-called Similarity Formulae. The validity of these formulae can be derived from the dimensionless formulation mentioned above. In the parametric analysis the maximum response of the bridge is obtained for one thousand values of speed that cover the range from the fourth resonance of the first mode to the first resonance of the second mode. The response at twenty-one different locations along the span of the beam is compared in order to decide if the maximum can be accurately computed with the sole contribution of the fundamental mode.

A damage model for seismic retrofitting of structures

Numerous damage models have been developed in order to analyse the seismic behavior. Among the different possibilities existing in the literature, it is very clear that models developed along the lines of Continuum Damage Mechanics are more consistent with the definition of damage like a phenomenon with mechanical consequences as they include explicitly the coupling between damage and mechanical behavior. On the other hand, for seismic processes, phenomena such as low cycle fatigue may have a pronounced effect on the overall behavior of the frames and, therefore, its consideration turns out to be very important. However, many of existing models evaluate the damage only as a function of the maximum amplitude of cyclic deformation without considering the number of cycles. In this paper, a generalization of the simplified model proposed by Flórez is made in order to include the low cycle fatigue. Such model employs in its formulation irreversible thermodynamics and internal state variable theory.

Vibrations of Short Span Railway Bridges for High Speed Lines

The physical model based on moving constant loads is widely used for the analysis of railway bridges. Nevertheless, this model is not well-suited for the study of short span bridges (L<=15-20 m), and the results it produces (displacements and accelerations) are much greater than those obtained experimentally. In this paper two factors are analysed which are believed to have an influence in the dynamic behaviour of short bridges. These two factors are not accounted for by the moving loads model and are the following: the distribution of the loads due to the presence of the sleepers and ballast layer, and the train-bridge interaction. Several numerical simulations have been performed in order to decide on their influence, and the results are presented and discussed herein.

Influence of the Second Bending Mode on the Response of High-Speed Bridges at Resonance

This paper deals with the assessment of the contribution of the second bending mode to the dynamic behavior of simply supported railway bridges. Traditionally the contributions of modes higher than the fundamental have been considered of little importance for the computation of the magnitudes of interest to structural engineers (vertical deflections, bending moments, etc.). Starting from the dimensionless equations of motion of a simply supported beam subjected to moving loads, the key parameters governing the dynamic behavior are identified. Then, a parametric study over realistic ranges of values of those parameters is conducted, and the influence of the second mode examined in detail. The main purpose is to decide whether the second mode should be taken into account for the determination of the maximum displacement and acceleration in high-speed bridges. In addition, the reasons that cause the contribution of the second bending mode to be relevant in some situations are highlighted, particularly with regard to the computation of the maximum acceleration.

Extension of Euskalduna Conference Centre and Concert Hall: A Contemporary Application of Irregular Reciprocal Frames

Reciprocal frame structures, formed by a set of self-supported elements in a closed circuit, have long been used since antiquity to cover large spans with small elements. The roof structure of the Euskalduna conference centre and concert hall extension in Bilbao, covering an irregu- lar geometry of 3000 m2 with a maximum span of 45 m, presented an interesting opportunity to revisit the concept and to apply these classical systems. Furthermore, its analysis and develop- ment led to an interesting discussion on reciprocal frames. They showed great sensitivity of these systems to the local modification of a particular element, establishment of irregular load paths, mobilisation of almost the entire sys- tem when locally applying a punctual load and, finally, its large deformability. Besides, reciprocal frames present particular construction complexities and possibilities due to the moderate length of the structural elements, the predominance of shear-only connec- tions and the necessity of the entire system to be completely erected to guarantee its stability. Euskalduna extension, completed in 2012, is one of the largest and a very par- ticular case of irregular reciprocal frame structures built in the world. It shows the formal possibilities and potentiality of reciprocal frames to respond to free and irregular geometries.

Aplicación de algoritmos paramétricos de generación formal en el diseño estructural. La Ópera de Sídney desde una perspectiva contemporánea.

El importante desarrollo tecnológico e industrial surgido especialmente durante la segunda mitad del siglo pasado ha eliminado las históricas limitaciones técnicas en el ámbito de los pro-­? yectos arquitectónicos, desembocando en la situación actual en la que cualquier planteamiento formal puede ser analizado desde un punto de vista estructural, concluyéndose por tanto que ha desaparecido la barrera del análisis en lo que al desarrollo de un proyecto arquitectónico se refiere. En la actualidad, al igual que a finales del siglo XIX, nos encontramos en un periodo de transi-­? ción, y también, como entonces, es la tecnología la que orienta el cambio. No la tecnología de los nuevos materiales (hormigón y acero) como sucedía tras la revolución industrial sino que es la nueva tecnología digital aplicada a los sistemas de diseño, cálculo y fabricación la que están siendo el motor de la actual transformación. Hoy no es tanto el paradigma mecanicista el que prevalece en muchos casos en la concepción de los edificios sino que, nuevos elementos como la tecnología digital integrada está cambiando la forma de diseñar y concebir el entorno cons-­? truido. Ante este contexto cabría plantearse las siguientes cuestiones: ¿Puede el diseño paramétrico y la tecnología CAD-­?CAM-­?CAE en conjunción con los programas actuales de análisis estructural basados en el Método de los Elementos Finitos hacer más sencilla la construcción de estructu-­? ras ligeras y eficientes hoy en día? ¿Puede la tecnología digital ayudar a ampliar el abanico for-­? mal a la hora de diseñar edificios y a la vez permitir el uso de sistemas estructurales racionales que optimicen el consumo de materiales bajo dichas circunstancias?

New Courthouse at El Ejido

The courthouse at El Ejido has a trapezoid floor plan (47 m × 55/26 m) and comprises two distinct volumes that are structurally connected at the basement level and by the footbridges on the upper storeys. A third trapezoid unit featuring a glazed curtain wall facade cantilevers 8 m off the main facade of the front volume. This facade is a structural diaphragm wall, constituted by nine rows of vertical precast concrete members separated by horizontal cast-in-place, self-compacting concrete chords. The location of the courthouse in a seismic area and the small number of horizontal supports for the facade make this wall potentially vulnerable. The high risk, in particular, during construction required careful planning based on a detailed analysis of the interaction between the structure and the ancillary resources used to build it