Simultaneous biosorption of methylene blue and trivalent chromium onto olive stone

In this work, olive stone (OS) was utilized to investigate its capacity as biosorbent for methylene blue (MB) and Cr(III), which are usually present in textile industry effluents. Equilibrium and kinetic experiments were performed in batch experiments. The biosorption process followed pseudo-second-order kinetics. The equilibrium data were fitted with several models, but Langmuir and Sips models best reproduced the experimental results. Maximum biosorption capacities were 3.296 mg/g (0.0116 mmol/g) and 4.990 mg/g (0.0960 mmol/g) for MB and Cr(III), respectively. Several operation variables, such as
biosorbent mass, flow rate, and initial concentration on the removal of dye and metal, were evaluated in column system. The removal efficiency improved as OS mass increased and decreased when flow rate and initial concentration increased. Also, MB uptake was substantially decreased by increasing the initial concentration of Cr(III), ranging from 6.09 to 2.75 mg/g. These results show that the presence of Cr(III) significantly modifies the biosorption capacity of MB by the OS. These results suggest that OS is a potential low-cost food industry waste for textile industry wastewater treatment.

Mechanism of Alizarin Red S and Methylene Blue Biosorption onto Olive Stone: Isotherm study in Single and Binary Systems

The biosorption process of anionic dye Alizarin Red S (ARS) and cationic dye methylene blue (MB) as a function of contact time, initial concentration and solution pH onto olive stone (OS) biomass has been investigated. Equilibrium biosorption isotherms in single and binary systems and kinetics in batch mode were also examined. The kinetic data of the two dyes were better described by the pseudo second-order model. At low concentration, ARS dye appeared to follow a two-step diffusion process, while MB dye followed a three-step diffusion process. The biosorption experimental data for ARS and MB dyes were well suited to the Redlich-Peterson isotherm. The maximum biosorption of ARS dye, qmax = 16.10 mg/g, was obtained at pH 3.28 and the maximum biosorption of MB dye, qmax = 13.20 mg/g, was observed at basic pH values. In the binary system, it was indicated that the MB dye diffuses firstly inside the biosorbent particle and occupies the biosorption sites forming a monodentate complex and then the ARS dye enters and can only bind to untaken sites; forms a tridentate complex with OS active sites.

The Middle Stone Age of Eastern Africa

The Middle Stone Age (MSA) covers the evolution, emergence, and dispersal of Homo sapiens. This article focuses on archaeological data and on published material from key stratified sites with some form of geochronological control from across eastern Africa. The MSA is often characterised by a shift from handaxe production towards discoidal and Levallois techniques. Although evidence for the controlled use of fire remains minimal, it seems likely that MSA hominins used it, as well as being highly skilled in working stone and probably bone and wood. MSA hominins appear to have exploited a range of different ecozones and many MSA sites are focused on ecotones, maximising access to resources. Over time, use of rockshelters and caves also seems to have increased. Although much work remains, the MSA is presently one of the most exciting and dynamic periods in the study of human evolution.

The inventorying of building stone performance-in-use to assess susceptibility to decay

The Natural Stone Database for Northern Ireland was constructed to address the paucity of information available to stone conservation practitioners within the region. Almost 2000 listed buildings and monuments were surveyed over three years to produce an interactive GIS database. This contained information on stone sources, together with details of stone condition and decay processes. This paper uses elements of this GIS to investigate stone decay patterns across Northern Ireland. The results demonstrate that as the level of stone decay increases, so does the proportion of buildings with sandstone as the primary stone type. It appears that a
higher open porosity level combined with Northern Ireland’s wetter climate and maritime location leads to rapid wetting and drying cycles within sandstones. This is coupled with the ingress and crystallisation of marine and other salts within stone pores leading to considerably
higher rates of decay than for any other stone type.

The comparative in situ hygrothermal performance of Hemp and Stone Wool insulations in vapour open timber frame wall panels

An in situ experiment in a full scale timber frame test building was carried out to compare the hygrothermal performance of Hemp and Stone Wool insulations of identical thermal conductivity. Hemp and Stone Wool insulations were installed in timber frame wall panels without vapour barrier. The comparison was made in terms of heat transfer properties, likelihood of mould growth and condensation. Step changes in internal relative humidity were performed to explore the effect of high and normal internal moisture load on the wall panels. No significant difference between the average equivalent thermal transmittance (U-values) of the panels incorporating Hemp and Stone Wool insulations was observed. The average equivalent U-values of the panels were closer to the calculated U-values of the panels based on the manufacturers’ declared thermal conductivity of Hemp and Stone Wool insulations. It was observed that the placement of heat flux sensor along the depth of the insulation had significant influence on the measured equivalent U-value of the panels during high internal moisture load. The frequency and likelihood of condensation was higher in the interface of Stone Wool and Oriented Strand Board (OSB). In terms of the parametric assessment of mould germination potential, relative humidity, temperature and exposure conditions in the insulation-OSB interfaces were found to be favourable to germination of mould spore. However, when the insulations were dismantled, no mould was visually detected.

Quasi steady state and dynamic hygrothermal performance of fibrous Hemp and Stone Wool insulations: Two innovative laboratory based investigations

Moisture and heat management properties of Hemp and Stone Wool insulations were studied by mounting them between a hot and a cold climate chamber. Both insulations were exposed to identical hygrothermal boundary conditions. Quasi steady state and dynamic tests were carried out at a range of relative humidity exposures. The likelihood of interstitial condensation was assessed and equivalent thermal conductivity values of the insulations were determined. The adsorption-desorption isotherms of the insulations were also determined in a dynamic vapour sorption (DVS) instrument. It was observed that the likelihood of condensation was higher in Stone Wool insulation than in Hemp insulation. Hemp insulation performed better in managing moisture due to its high hygric inertia and water absorption capacity. It was observed that the equivalent thermal conductivity of Stone Wool insulation was dependent on enthalpy flow and phase change of moisture. The equivalent thermal conductivity of Hemp insulation was close to its declared thermal conductivity in dynamic conditions when high relative humidity exposures were transient. In quasi steady state boundary conditions, when the insulation was allowed to reach the equilibrium moisture content at ranges of relative humidity, there was a moisture dependent increase of thermal conductivity in Hemp insulation.

Tecnologia lítica da Middle Stone Age da Gruta da Leba (Huíla, SW Angola)

África é hoje o foco principal na investigação sobre a problemática da emergência da humanidade. O registo arqueológico actual sugere que também alinhagem do Homo sapiens surgiu na África subsaariana, tornando a Middle Stone Age no período chave no debate sobre a emergência do comportamento humano moderno. Os primeiros indícios de comportamento humano presumivelmente moderno provêm da África do Sul, mas há um enorme vazio arqueográfico sobre as áreas limítrofes desse território como é o caso de Angola que podem trazer novos dados à discussão. A presente dissertação debruça-se sobre a colecção arqueológica da Gruta da Leba (Huíla, SW de Angola), actualmente parte do Arquivo Científico Tropical (Instituto de Investigação Científica Tropical), que permanece inédita, apesar de recolhida em escavação arqueológica pela Junta de Investigações do Ultramar durante os anos 1950, no âmbito da Missão Antropobiológica de Angola. O conjunto é composto por uma indústria lítica com mais de 1500 peças, bem como restos faunísticos e amostras de sedimentos, de uma sequência estratigráfica com três níveis de ocupação da Middle Stone Age. O principal objectivo deste estudo é caracterizar a produção e utilização dos materiais líticos da Middle Stone Age da Gruta da Leba, através da sistematização da informação de cariz tecnológico e tipológico do conjunto artefactual. A partir da análise dos materiais líticos é possível definir padrões de variabilidade na exploração das matérias-primas e cadeias operatórias de produção do sítio. Pretende-se, assim, enquadrar regionalmente as indústrias líticas no panorama mais alargado da Pré-História da África subsaariana, para a validação dos modelos crono-culturais convencionais e avaliação dos parâmetros teórico-metodológicos aplicados na abordagem à tecnologia lítica africana em relação à problemática do comportamento humano moderno.

Foundation Stone due date card

This is a due date card for the book titled Foundation Stone, with stamped dates from 1941-1943.

Population and landscape genetics of the stone marten and red fox in Portugal : implications for conservation management of common carnivores

Tese de doutoramento, Biologia (Biologia da Conservação), Universidade de Lisboa, Faculdade de Ciências, 2015

Implementação de um processo industrial de coloração de granito

O presente estágio foi desenvolvido na Britafiel. Um dos projectos em que a Empresa se encontra envolvida é o STOCO, pretendendo implementar à escala industrial um processo de coloração de pedra granítica natural para fins decorativos. Foi neste projecto que se enquadrou o estágio. O tema do estágio centra-se no processo de coloração de granito tendo como principal foco a implementação de um processo industrial de produção de granito colorido. O projecto STOCO nasce da necessidade de complementar a actividade da empresa com produtos de maior valor acrescentado para valorização da matéria-prima de base, o granito. STOCO, resultante de Stone Color, é o nome dado ao projecto e ao novo produto que é granito colorido, sob a forma de brita. Pretende-se obter um produto amigo do ambiente e com boas características: manter a textura natural da pedra granítica e assegurar uma boa resistência a factores agressivos. Estudos prévios de qualidade e de toxicidade mostraram que o produto STOCO desenvolvido até então apresenta um bom comportamento face a agressões climatéricas e que não compromete a vida das espécies usadas nos testes (peixes). Em relação aos lixiviados e resíduos da pedra colorida STOCO, estes não apresentaram qualquer problema ambiental, sendo considerado um produto amigo do ambiente. À data de início do presente trabalho estava em funcionamento um equipamento protótipo de produção de granito colorido (100 kg/partida), sendo a instalação e o arranque da unidade industrial (3 ton/h) concretizados no início de 2014, já no decorrer deste trabalho. Os objectivos cumpridos no âmbito deste trabalho foram então a implementação de uma linha industrial de produção de brita colorida, avaliação técnica do processo e do custo industrial de produção associado às matérias-primas. Neste relatório é descrito o processo inicial adoptado e apresentam-se as alterações efectuadas para melhoria do processo produtivo. Resolveram-se problemas como: definição e instalação de equipamentos complementares para a entrada e a saída da brita no equipamento industrial; pó excessivo na brita; cheiro intenso a gás e elevado ruído; adequação do sistema de pintura; e secagem incompleta da brita. Alguns destes problemas não foram totalmente resolvidos, mas sim minimizados. O equipamento industrial necessita ainda de alterações em diversas áreas, que foram identificadas e para as quais são feitas sugestões de melhoria. Conseguiu-se ainda fazer alguns testes para uma possível substituição de alguns constituintes da tinta. Os componentes que entram na composição base da tinta aquosa, são de modo simplificado: ligante, pigmento, solvente e aditivos. Os constituintes que mais encarecem a tinta, e consequentemente o processo em causa, são o ligante e o pigmento. Os estudos efectuados precisam de ser aprofundados, na tentativa de melhorar o processo minimizando os custos de produção. Formalizaram-se os procedimentos escritos de produção STOCO tanto para o protótipo como para o processo industrial e elaborou-se uma ficha técnica de produto para a brita colorida STOCO.