Admittance spectroscopy of Cu2ZnSnS4 based thin film solar cells

In this report, we propose an AC response equivalent circuit model to describe the admittance measurements of Cu2ZnSnS4 thin film solar cell grown by sulphurization of stacked metallic precursors. This circuit describes the contact resistances, the back contact, and the heterojunction with two trap levels. The study of the back contact resistance allowed the estimation of a back contact barrier of 246 meV. The analysis of the trap series with varying temperature revealed defect activation energies of 45 meV and 113 meV. The solar cell’s electrical parameters were obtained from the J-V curve: conversion efficiency, 1.21%; fill factor, 50%; open circuit voltage, 360 mV; and short circuit current density, 6.8 mA/cm2.

Planeamento de curto prazo de sistemas de energia solar usando técnicas de otimização robusta

Dissertação para obtenção do grau de Mestre em Engenharia Electrotécnica

Cu2ZnSnS4 solar cells prepared with sulphurized dc-sputtered stacked metallic precursors

In the present work we report the details of the preparation and characterization results of Cu2ZnSnS4 (CZTS) based solar cells. The CZTS absorber was obtained by sulphurization of dc magnetron sputtered Zn/Sn/Cu precursor layers. The morphology, composition and structure of the absorber layer were studied by scanning electron microscopy, energy dispersive spectroscopy, X-ray diffraction and Raman scattering. The majority carrier type was identified via a hot point probe analysis. The hole density, space charge region width and band gap energy were estimated from the external quantum efficiency measurements. A MoS2 layer that formed during the sulphurization process was also identified and analyzed in this work. The solar cells had the following structure: soda lime glass/Mo/CZTS/CdS/i-ZnO/ZnO:Al/Al grid. The best solar cell showed an opencircuit voltage of 345 mV, a short-circuit current density of 4.42 mA/cm2, a fill factor of 44.29% and an efficiency of 0.68% under illumination in simulated standard test conditions: AM 1.5 and 100 mW/cm2.

Growth and characterization of Cu2ZnSn(S,Se)4 thin films for solar cells

Cu2ZnSnS4 (CZTS) and Cu2ZnSnSe4 (CZTSe) with their band gap energies around 1.45 eV and 1.0 eV, respectively, can be used as the absorber layer in thin film solar cells. By using a mixture of both compounds, Cu2ZnSn(S,Se)4 (CZTSSe), a band gap tuning may be possible. The latter material has already shown promising results such as solar cell efficiencies up to 10.1%. In this work, CZTSSe thin films were grown in order to study its structure and to establish the best growth precursors. SEM micrographs reveal an open columnar structure for most samples and EDS composition profiling of the cross sections show different selenium gradients. X-ray diffractograms show different shifts of the kesterite/stannite (1 1 2) peak, which indicate the presence of CZTSSe. From Raman scattering analysis, it was concluded that all samples had traces of CZTS and CZTSSe. The composition of the CZTSSe layer was estimated using X-ray diffraction and Raman scattering and both results were compared. It was concluded that Se diffused more easily in precursors with ternary Cu–Sn–S phases and metallic Zn than in precursors with ZnS and/or CZTS already formed. It was also showed that a combination of X-ray diffraction and Raman scattering can be used to estimate the ratio of S per Se in CZTSSe samples.

Desempenho energético no âmbito do aquecimento solar térmico para as condições de utilização recomendadas pelo RSECE/RCCTE

Trabalho Final de Mestrado para obtenção do grau de Mestre em Engenharia Mecânica

Novos compostos orgânicos reticuláveis para aplicações em células fotovoltaicas

Trabalho Final de Mestrado para obtenção do grau de mestre em Engenharia Química e Biológica

PV system modeling by five parameters and in situ test

This paper focuses on a novel formalization for assessing the five parameter modeling of a photovoltaic cell. An optimization procedure is used as a feasibility problem to find the parameters tuned at the open circuit, maximum power, and short circuit points in order to assess the data needed for plotting the I-V curve. A comparison with experimental results is presented for two monocrystalline PV modules.

Bifacial dye-sensitized solar cells: a strategy to enhance overall efficiency based on transparent polyaniline electrode

Dye-sensitized solar cell (DSSC) is a promising solution to global energy and environmental problems because of its clean, low-cost, high efficiency, good durability, and easy fabrication. However, enhancing the efficiency of the DSSC still is an important issue. Here we devise a bifacial DSSC based on a transparent polyaniline (PANI) counter electrode (CE). Owing to the sunlight irradiation simultaneously from the front and the rear sides, more dye molecules are excited and more carriers are generated, which results in the enhancement of short-circuit current density and therefore overall conversion efficiency. The photoelectric properties of PANI can be improved by modifying with 4-aminothiophenol (4-ATP). The bifacial DSSC with 4-ATP/PANI CE achieves a light-to-electric energy conversion efficiency of 8.35%, which is increased by ,24.6% compared to the DSSC irradiated from the front only. This new concept along with promising results provides a new approach for enhancing the photovoltaic performances of solar cells.

PV system modeling by five parameters and in Situ test

This paper focuses on a novel formalization for assessing the five parameter modeling of a photovoltaic cell. An optimization procedure is used as a feasibility problem to find the parameters tuned at the open circuit, maximum power, and short circuit points in order to assess the data needed for plotting the I-V curve. A comparison with experimental results is presented for two monocrystalline PV modules.

Energia solar fotovoltaica: contributo para um roadmapping do seu desenvolvimento tecnológico

Trabalho realizado sob orientação do Prof. António Brandão Moniz para a disciplina “Sócio-Economia da Inovação” do Mestrado Engenharia Integrado em Engenharia Electrotécnica e Computadores realizado na Faculdade de Ciências e Tecnologia da Universidade Nova de Lisboa (Portugal)

Detecção e quantificação automática da actividade solar

Dissertação para obtenção do grau de Mestrado Integrado em Engenharia Electrotécnica e de Computadores

Técnica de separação de cor para fotocoagulação com luz solar concentrada

Dissertação apresentada na Faculdade de Ciências e Tecnologia da Universidade Nova de Lisboa para obtenção do grau de Mestre em Engenharia Biomédica

Módulo fotovoltaico com seguimento da posição solar

Dissertação apresentada na Faculdade de Ciências e Tecnologia da Universidade Nova de Lisboa para obtenção do grau de Mestre em Engenharia Electrotécnica e de Computadores

Desirable role in an international duopoly model with tariffs

In this paper, we study an international market model in which the home government imposes a tariff on the imported goods. The model has two stages. In the first stage, the home government chooses an import tariff to maximize a function that cares about the home firm’s profit and the total revenue. Then, the firms engage in a Cournot or in a Stackelberg competition. We compare the results obtained in the three different ways of moving on the decision make of the firms.

Environmental and international tariffs in a mixed duopoly

In this paper, we study the effects of environmental and trade policies in an international mixed duopoly serving two markets, in which the public firm maximizes the sum of consumer surplus and its profit. We also analyse the effects of privatization. The model has two stages. In the first stage, governments choose environmental taxes and import tariffs, simultaneously. Then, the firms engage in a Cournot competition, choosing output levels for the domestic market and to export. We compare the results obtained in the three different ways of moving on the decision make of the firms.