On the Mixed Modulus of Smoothness and a Class of Double Fourier Series

MSC 2010: 42A32; 42A20

Elastic modulus study of gold thin film for use as an actuated membrane in a superconductive radio frequency (RF) microelectromechanical (MEM) switch

The objective of this research was to find Young's elastic modulus for thin gold films at room and cryogenic temperatures based on the flexional model which has not been previously attempted. Electrical Sonnet simulations and numerical methods using Abacus for the mechanical responses were employed for this purpose. A RF MEM shunt switch was designed and a fabrication process developed in house. The switch is composed of a superconducting YBa2 Cu3O7 coplanar waveguide structure with an Au bridge membrane suspended above an area of the center conductor covered with BaTiO3 dielectric. The Au membrane is actuated by the electrostatic attractive force acting between the transmission line and the membrane when voltage is applied. The value of the actuation force will greatly depend on the switch pull-down voltage and on the geometry and mechanical properties of the bridge material. Results show that the elastic modulus for Au thin film can be 484 times higher at cryogenic temperature than it is at room temperature. ^

Elastic modulus study of gold thin film for use as an actuated membrane in a superconductive radio frequency (RF) MicroElectroMechanical (MEM) switch

The objective of this research was to find Young's elastic modulus for thin gold films at room and cryogenic temperatures based on the flexional model which has not been previously attempted. Electrical Sonnet simulations and numerical methods using Abacus for the mechanical responses were employed for this purpose. A RF MEM shunt switch was designed and a fabrication process developed in house. The switch is composed of a superconducting YBa2Cu3O7 coplanar waveguide structure with an Au bridge membrane suspended above an area of the center conductor covered with BaTiO3 dielectric. The Au membrane is actuated by the electrostatic attractive force acting between the transmission line and the membrane when voltage is applied. The value of the actuation force will greatly depend on the switch pull-down voltage and on the geometry and mechanical properties of the bridge material. Results show that the elastic modulus for Au thin film can be 484 times higher at cryogenic temperature than it is at room temperature.

Measurements of stress-optic coefficient and Young's modulus in PMMA fibers drawn under different conditions

We have systematically measured the differential stress-optic coefficient, ΔC, and Young's modulus, E, in a number of PMMA fibers drawn with different stress, ranging from 2 up to 27 MPa. Effect of temperature annealing on those parameters was also investigated. ΔC was determined in transverse illumination by measuring the dependence of birefringence on additional axial stress applied to the fiber. Our results show that ΔC in PMMA fibers has a negative sign and ranges from -4.5 to -1.5×10-12 Pa -1 depending on the drawing stress. Increase of the drawing stress results in greater initial fiber birefringence and lower ΔC. The dependence of ΔC and initial birefringence upon drawing stress is nonlinear and gradually saturates for higher drawing stress. Moreover, we find that ΔC is linearly proportional to initial fiber birefringence and that annealing the fiber has no impact on the slope of this dependence. On the other hand, no clear dependence was observed between the fiber drawing stress and the Young's modulus of the fibers as measured using microscopic digital image correlation with the fibers tensioned using an Instron tension tester. © 2010 SPIE.

The swimming kinematics of larval Atlantic cod, Gadus morhua L., are resilient to elevated seawater pCO2

Kinematics of swimming behavior of larval Atlantic cod, aged 12 and 27 days post-hatch (dph) and cultured under three pCO2 conditions (control-370, medium-1800, and high-4200 µatm) from March to May 2010, were extracted from swim path recordings obtained using silhouette video photography. The swim paths were analyzed for swim duration, distance and speed, stop duration, and horizontal and vertical turn angles to determine whether elevated seawater pCO2-at beyond near-future ocean acidification levels-affects the swimming kinematics of Atlantic cod larvae. There were no significant differences in most of the variables tested: the swimming kinematics of Atlantic cod larvae at 12 and 27 dph were highly resilient to extremely elevated pCO2 levels. Nonetheless, cod larvae cultured at the highest pCO2 concentration displayed vertical turn angles that were more restricted (median turn angle, 15°) than larvae in the control (19°) and medium (19°) treatments at 12 dph (but not at 27 dph). Significant reduction in the stop duration of cod larvae from the high treatment (median stop duration, 0.28 s) was also observed compared to the larvae from the control group (0.32 s) at 27 dph (but not at 12 dph). The functional and ecological significance of these subtle differences are unclear and, therefore, require further investigation in order to determine whether they are ecologically relevant or spurious.

Progress and Research in Cybersecurity - Supporting a resilient and trustworthy system for the UK

Executive summary
Digital systems have transformed, and will continue to transform, our world. Supportive government policy, a strong research base and a history of industrial success make the UK particularly well-placed to realise the benefits of the emerging digital society. These benefits have already been substantial, but they remain at risk. Protecting the benefits and minimising the risks requires reliable and robust cybersecurity, underpinned by a strong research and translation system.
Trust is essential for growing and maintaining participation in the digital society. Organisations earn trust by acting in a trustworthy manner: building systems that are reliable and secure, treating people, their privacy and their data with respect, and providing credible and comprehensible information to help people understand how secure they are.
Resilience, the ability to function, adapt, grow, learn and transform under stress or in the face of shocks, will help organisations deliver systems that are reliable and secure. Resilient organisations can better protect their customers, provide more useful products and services, and earn people’s trust.
Research and innovation in industry and academia will continue to make important contributions to creating this resilient and trusted digital environment. Research can illuminate how best to build, assess and improve digital systems, integrating insights from different disciplines, sectors and around the globe. It can also generate advances to help cybersecurity keep up with the continued evolution of cyber risks.
Translation of innovative ideas and approaches from research will create a strong supply of reliable, proven solutions to difficult to predict cybersecurity risks. This is best achieved by maximising the diversity and number of innovations that see the light of day as products.
Policy, practice and research will all need to adapt. The recommendations made in this report seek to set up a trustworthy, self-improving and resilient digital environment that can thrive in the face of unanticipated threats, and earn the trust people place in it.
Innovation and research will be particularly important to the UK’s economy as it establishes a new relationship with the EU. Cybersecurity delivers important economic benefits, both by underpinning the digital foundations of UK business and trade and also through innovation that feeds directly into growth. The findings of this report will be relevant regardless of how the UK’s relationship to the EU changes.
Headline recommendations
● Trust: Governments must commit to preserving the robustness of encryption, including end-to-end encryption, and promoting its widespread use. Encryption is a foundational security technology that is needed to build user trust, improve security standards and fully realise the benefits of digital systems.
● Resilience: Government should commission an independent review of the UK’s future cybersecurity needs, focused on the institutional structures needed to support resilient and trustworthy digital systems in the medium and longer term. A self-improving, resilient digital environment will need to be guided and governed by institutions that are transparent, expert and have a clear and widely-understood remit.
● Research: A step change in cybersecurity research and practice should be pursued; it will require a new approach to research, focused on identifying ambitious high-level goals and enabling excellent researchers to pursue those ambitions. This would build on the UK's existing strengths in many aspects of cybersecurity research and ultimately help build a resilient and trusted digital sector based on excellent research and world-class expertise.
● Translation: The UK should promote a free and unencumbered flow of cybersecurity ideas from research to practical use and support approaches that have public benefits beyond their short term financial return. The unanticipated nature of future cyber threats means that a diverse set of cybersecurity ideas and approaches will be needed to build resilience and adaptivity. Many of the most valuable ideas will have broad security benefits for the public, beyond any direct financial returns.

Noise resilient discrete-time cross-relation sensor characterisation

In-situ characterisation of thermocouple sensors is a challenging problem. Recently the authors presented a blind characterisation technique based on the cross-relation method of blind identification. The method allows in-situ identification of two thermocouple probes, each with a different dynamic response, using only sampled sensor measurement data. While the technique offers certain advantages over alternative methods, including low estimation variance and the ability to compensate for noise induced bias, the robustness of the method is limited by the multimodal nature of the cost function. In this paper, a normalisation term is proposed which improves the convexity of
the cost function. Further, a normalisation and bias compensation hybrid approach is presented that exploits the advantages of both normalisation and bias compensation. It is found that the optimum of the hybrid cost function is less biased and more stable than when only normalisation is applied. All results were verified by simulation.

Dealing with flood damages: will prevention, mitigation, and ex post compensation provide for a resilient triangle?

There is a wealth of literature on the design of ex post compensation mechanisms for natural disasters. However, more research needs to be done on the manner in which these mechanisms could steer citizens toward adopting individual-level preventive and protection measures in the face of flood risks. We have provided a comparative legal analysis of the financial compensation mechanisms following floods, be it through insurance, public funds, or a combination of both, with an empirical focus on Belgium, the Netherlands, England, and France. Similarities and differences between the methods in which these compensation mechanisms for flood damages enhance resilience were analyzed. The comparative analysis especially focused on the link between the recovery strategy on the one hand and prevention and mitigation strategies on the other. There is great potential within the recovery strategy for promoting preventive action, for example in terms of discouraging citizens from living in high-risk areas, or encouraging the uptake of mitigation measures, such as adaptive building. However, this large potential has yet to be realized, in part because of insufficient consideration and promotion of these connections within existing legal frameworks. We have made recommendations about how the linkages between strategies can be further improved. These recommendations relate to, among others, the promotion of resilient reinstatement through recovery mechanisms and the removal of legal barriers preventing the establishment of link-inducing measures.

The Welsh Marches: Resilient Farmers? Exploring Farmers' Resilience to Extreme Weather Events in the Recent Past

In the 21st century climate change will cause a significant increase in the frequency and intensity of extreme weather events across Europe. Investigating farmers’ resilience to extreme weather events in the past can be used to establish the inherent level of resilience farmers’ will have to respond to comparable events in the future. The Welsh Marches has experienced a range of extreme weather events including: heatwaves, flooding; prolonged rainfall; and heavy snowfall. To identify the resilience of farmers in the Marches farmers’ apparent vulnerabilities, coping capacity, social capital and adaptive capacity that have been exposed in past events are discussed. Rural isolation is identified as an exacerbating factor of farming vulnerability. Yet, this is also an apparent source of resilience as farmers are found to rely on high social capital to assist each other in emergency and challenging situations during extreme weather events. The paper concludes by indicating that more localised studies are required, situated within unique farming cultures. This will enable a more complete picture of farmers’ resilience across Europe to be established.

Why resilience managers aren’t resilient, and what human resource management can do about it

Prior resilience research typically focuses on either the individual or the organisational level of analysis, emphasises resilience in relation to day-to-day stressors rather than extreme events and is empirically under-developed. In response, our study inductively theorises about the relationships between individual and organisational resilience, drawing upon a large-scale study of resilience work in UK and French organisations. Our first-hand accounts of resilience work reveal the micro-processes involved in producing resilient organisations, and highlight the challenges experienced in doing resilience work in large organisations. We show that these micro-processes have significant implications for resilience at both individual and organisational levels, and draw implications for how HRM interventions can help to promote individual, and thus organisational, resilience.

Influence Of Fluorescent Dye On Physical-mechanical Properties Of Luting Cements For Confocal Microscopy Analysis.

To evaluate the influence of a fluorescent dye (rhodamine B) on the physical and mechanical properties of three different luting cements: a conventional adhesive luting cement (RelyX ARC, 3M/ESPE), a self-adhesive luting cement (RelyX U-200, 3M/ESPE), and a self-etching and self-adhesive luting cement (SeT PP, SDI). The cements were mixed with 0.03 wt% rhodamine B, formed into bar-shaped specimens (n = 10), and light cured using an LED curing unit (Radii, SDI) with a radiant exposure of 32 J/cm(2) . The Knoop hardness (KHN), flexural strength (FS), and Young's modulus (YM) analyses were evaluated after storage for 24 h. Outcomes were subjected to two-way ANOVA and Tukey's test (P = 0.05) for multiple comparisons. No significant differences in FS or YM were observed among the tested groups (P ≥ 0.05); the addition of rhodamine B increased the hardness of the luting cements tested. The addition of a fluorescent agent at 0.03 wt% concentration does not negatively affect the physical-mechanical properties of the luting cement polymerization behavior.

Bipolar Tribocharging Signal During Friction Force Fluctuations At Metal-insulator Interfaces.

Friction and triboelectrification of materials show a strong correlation during sliding contacts. Friction force fluctuations are always accompanied by two tribocharging events at metal-insulator [e.g., polytetrafluoroethylene (PTFE)] interfaces: injection of charged species from the metal into PTFE followed by the flow of charges from PTFE to the metal surface. Adhesion maps that were obtained by atomic force microscopy (AFM) show that the region of contact increases the pull-off force from 10 to 150 nN, reflecting on a resilient electrostatic adhesion between PTFE and the metallic surface. The reported results suggest that friction and triboelectrification have a common origin that must be associated with the occurrence of strong electrostatic interactions at the interface.

Photoelastic Analysis Of All-on-four Concept Using Different Implants Angulations For Maxilla.

Conventional tilted implants are used in oral rehabilitation for heavily absorbed maxilla to avoid bone grafts; however, few research studies evaluate the biomechanical behavior when different angulations of the implants are used. The aim of this study was evaluate, trough photoelastic method, two different angulations and length of the cantilever in fixed implant-supported maxillary complete dentures. Two groups were evaluated: G15 (distal tilted implants 15°) and G35 (distal tilted implants 35°) n = 6. For each model, 2 distal tilted implants (3.5 x 15 mm long cylindrical cone) and 2 parallel tilted implants in the anterior region (3.5 x 10 mm) were installed. Photoelastic models were submitted to three vertical load tests: in the end of cantilever, in the last pillar and in the all pillars at the same time. We obtained the shear stress by Fringes software and found values for total, cervical and apical stress. The quantitative analysis was performed using the Student tests and Mann-Whitney test; p ≥ 0.05. There is no difference between G15 and G35 for total stress regardless of load type. Analyzing the apical region, G35 reduced strain values considering the distal loads (in the cantilever p = 0.03 and in the last pillar p = 0.02), without increasing the stress level in the cervical region. Considering the load in all pillars, G35 showed higher stress concentration in the cervical region (p = 0.04). For distal loads, G15 showed increase of tension in the apical region, while for load in all pillars, G35 inclination increases stress values in the cervical region.

One-dimensional Silicon And Germanium Nanostructures With No Carbon Analogues.

In this work we report new silicon and germanium tubular nanostructures with no corresponding stable carbon analogues. The electronic and mechanical properties of these new tubes were investigated through ab initio methods. Our results show that these structures have lower energy than their corresponding nanoribbon structures and are stable up to high temperatures (500 and 1000 K, for silicon and germanium tubes, respectively). Both tubes are semiconducting with small indirect band gaps, which can be significantly altered by both compressive and tensile strains. Large bandgap variations of almost 50% were observed for strain rates as small as 3%, suggesting their possible applications in sensor devices. They also present high Young's modulus values (0.25 and 0.15 TPa, respectively). TEM images were simulated to help in the identification of these new structures.