Assessment of the mechanical performance of recycled unbound materials for pavement subbase layers

The cyclic load triaxial test is a laboratory test that allows studying the mechanical behaviour of unbound granular materials used in base/subbase layers of road pavements. The resilient modulus and permanent strains are required as inputs in structural pavement design. This paper presents some results obtained for recycled materials (crushed concrete aggregate and blended crushed waste aggregate), with a view to promoting their use in pavement structures. Results relating to a reference material (limestone) are also presented, for comparison. All the test results discussed in this paper were obtained in variable cyclic radial pressure (VCP) tests. The tests performed (VCP) aim to study the influence of water content on the resilient modulus of recycled materials, as well as on the resistance to permanent deformation. Using the experimental data as a basis, further modelling work was carried out to establish the stresses developing in base/capping layers in typical Belgian road pavements. These numerical results allow to propose some simplifications of the stress paths applied in the testing procedures and to establish a new test protocol that also considers compaction during construction works. The results of this research work provide an excellent set of findings for the mechanical characterization of unbound base materials through the cyclic triaxial test, and contribute to a better understanding and correct application of recycled materials under geotechnical engineering background

Effect of argon ion energy on the performance of silicon nitridemultilayer permeation barriers grown by hot-wire CVD on polymers

One of the authors (S.M.) acknowledges Direction des Relations Extérieures of Ecole Polytechnique for financial support.

Quantifying, generating and mitigating radio interference in Low-Power Wireless Networks

Doctoral Programme in Telecommunication - MAP-tele

Development of an intelligent earthwork optimization system

Tese de Doutoramento em Engenharia Civil.

High performance screen printable lithium-ion battery cathode ink based on C-LiFePO4

Lithium-ion battery cathodes have been fabricated by screen-printing through the development of CLiFePO4 inks. It is shown that shear thinning polymer solutions in N-methyl-2-pyrrolidone (NMP) with Newtonian viscosity above 0.4 Pa s are the best binders for formulating a cathode paste with satisfactory film forming properties. The paste shows an elasticity of the order of 500 Pa and, after shear yielding, shows an apparent viscosity of the order of 3 Pa s for shear rates corresponding to those used during screen-printing. The screen-printed cathode produced with a thickness of 26 mm shows a homogeneous distribution of the active material, conductive additive and polymer binder. The total resistance and diffusion coefficient of the cathode are 450 V and 2.5 10 16cm2 s 1, respectively. The developed cathodes show an initial discharge capacity of 48.2 mAh g 1 at 5C and a discharge value of 39.8 mAh g 1 after 50 cycles. The capacity retention of 83% represents 23% of the theoretical value (charge and/or discharge process in twenty minutes), demonstrating the good performance of the battery. Thus, the developed C-LiFePO4 based inks allow to fabricate screen-printed cathodes suitable for printed lithium-ion batteries

A review of sustainable approaches in transport infrastructure geotechnics

Transportation geotechnics associated with constructing and maintaining properly functioning transportation infrastructure is a very resource intensive activity. Large amounts of materials and natural resources are required, consuming proportionately large amounts of energy and fuel. Thus, the implementation of the principles of sustainability is important to reduce energy consumption, carbon footprint, greenhouse gas emissions, and to increase material reuse/recycling, for example. This paper focusses on some issues and activities relevant to sustainable earthwork construction aimed at minimising the use of energy and the production of CO2 while improving the in-situ ground to enable its use as a foundation without the consumption of large amounts of primary aggregate as additional foundation layers. The use of recycled materials is discussed, including steel slag and tyre bales, alongside a conceptual framework for evaluating the utility of applications for recycled materials in transportation infrastructure.

Mejoramiento del comportamiento térmico de sistemas de calentamiento de agua solares termosifónicos hechos con materiales no convencionales y con tanques de almacenamiento verticales y horizontales Performance improvement of solar thermosyphonic systems for water heating made of non conventional materials and using horizontal and vertical storage tanks

El objeto de estudio de este proyecto son los sistemas de calentamiento de agua mediante energía solar que funcionan termosifónicamente. En particular se tratará con dos diseños particulares generados por fabricantes de la Provincia de Córdoba y que han solicitado el asesoramiento del Grupo de Energía Solar (GES) para el mejoramiento de la performance térmica de dichos equipos. Se trata de dos sistemas que tienen materiales no tradicionales y se diferencian además por tener una distinta disposición del tanque de almacenamiento: uno es en forma vertical y el otro en forma horizontal. Basados en los resultados de un ensayo bajo norma internacional, donde se detectaron algunas puntos factibles de mejora, se propone en este proyecto el análisis en detalle de los equipos, para lo cual se les debe desarmar completos, para realizar un estudio analítico y experimental de los mismos con el objeto de hacer un planteo teórico-analítico del comportamiento de los mismos, con la implementación de propuestas de mejora y chequeo de los resultados. Se propone entonces como objetivo lograr un mejoramiento de la performance térmica de los citados equipos a partir de un estudio experimental y analítico. Asumiendo esta posibilidad de mejora, se plantea la hipótesis de que es posible representar el funcionamiento de estos equipos mediante modelos físico-matemáticos desarrollados a partir de ecuaciones y correlaciones conocidas y procesos a interpretar mediante resoluciones numéricas y softwares específicos de simulación. De esta manera, se plantea el despieze completo de los equipos para estudiar en detalle su estructura y conexiones internas y a partir de la geometría, dimensiones y propiedades termofísicas de materiales constructivos y fluidos de trabajo, realizar modelos físico-matemáticos que permitan realizar variaciones de propiedades y geometría y así buscar las mejores combinaciones que produzcan equipos más eficientes térmicamente. Los modelos físico-matemáticos serán codificados en lenguajes de alto nivel para poder luego de una validación de los modelos, correr simulaciones en un software de reconocimiento internacional que permite sumar dichos modelos mediante un protocolo de comunicación, haciendo que las poderosas prestaciones del software se puedan aplicar a nuestros modelos. Se complementará el estudio con un análisis exergético para identificar los puntos críticos en que se producen las pérdidas de oportunidad de aprovechar la energía disponible, para así analizar cómo solucionar los problemas en dichos puntos. Los materiales a utilizar serán los propios equipos provistos por los fabricantes, que serán modificados convenientemente para operarlos como prototipos Se espera obtener un conocimiento acabado de los procesos y principios de funcionamiento de los equipos, que permita plantear las mejoras, las cuales se implementarán en los prototipos, realizándose una medición mediante norma igual a la inicial para ver en que magnitud se logran las mejoras esperadas. Se pretende además que las mejoras a implementar, en la etapa de transferencia a las empresas involucradas, redunden no sólo en un beneficio técnico, sino que también los sea desde el punto de vista económico. Para ello se trabajará también sobre los procesos y métodos de fabricación para que los equipos mejorados no sean mas caros que los originales y de ser posible sean aún más económicos, todo esto apuntando a la difusión de la energía solar térmica y poner al alcance de todos estos equipos tan convenientes para la propagación de las energías limpias. El proyecto redundará también en un importante beneficio para el conocimiento de la comunidad científica en general, con el aporte de nuevos resultados en diseños novedosos y con nuevos materiales. Además, la institución se beneficiará con la formación que obtendrán los integrantes del proyecto, muchos de ellos en etapa de realización de sus estudios de posgrado y en una etapa importante de su vida como investigadores. The main goal of this project is the improvement of two thermosyphonic solar water heating systems, made of non conventional materials and with different arrangement of their storage tanks: one is vertical and the other one horizontal. The thermosyphonic systems are provided by manufacturers of the Córdoba Province, who came to the Solar Energy Group (GES) of the National University of Río Cuarto looking for help for the design of their products. In an agreement with these manufacturers, it was proposed this project in order to work analytically and experimentally in order to obtain physical-mathematical models of these two systems, which allow for changes to look by means of simulations the best changes to implement on the equipments for the improvement of their thermal performance. Then, the materials to be used are the proper systems provided by the manufacturers, which will be disarmed to be studied in detail. After the analytical study the proposals of improvement will be implemented in a high level language of programming to perform simulations in the environment of a well-known software for energy simulations (TRNSYS). After the simulations, the best modifications will be physically implemented in the prototypes to perform finally the same normalized test of the beginning and check the magnitude of the implemented improvements. The importance of this project is based on the offer of better systems the companies would make, which would benefit the deployment of the thermal solar energy. Another relevant point is to make the new equipments at the same cost of the previous ones or cheaper, in order to achieve a good deployment of the solar water heating systems; then, the manufacture processes and methods must be studied to obtain not only good technical solutions, but also economical equipments. In addition, this project will contribute to the increasing of the knowledge in the area of thermosyphonic solar systems and the training of postgraduate students.

Instrumentation and software for the VERITAS Project and the detection of TeV Gamma-Ray Emission from the BL Lacertae Object 1ES1959+650

Transmission of Cherenkov light through the atmosphere is strongly influenced by the optical clarity of the atmosphere and the prevailing weather conditions. The performance of telescopes measuring this light is therefore dependent on atmospheric effects. This thesis presents software and hardware developed to implement a prototype sky monitoring system for use on the proposed next-generation gamma-ray telescope array, VERITAS. The system, consisting of a CCD camera and a far-infrared pyrometer, was successfully installed and tested on the ten metre atmospheric Cherenkov imaging telescope operated by the VERITAS Collaboration at the F.L. Whipple Observatory in Arizona. The thesis also presents the results of observations of the BL Lacertae object, 1ES1959+650, made with the Whipple ten metre telescope. The observations provide evidence for TeV gamma-ray emission from the BL Lacertae object, 1ES1959+650, at a level of more than 15 standard deviations above background. This represents the first unequivocal detection of this object at TeV energies, making it only the third extragalactic source seen at such levels of significance in this energy range. The flux variability of the source on a number of timescales is also investigated.

Development of tools to measure and explain changes in health inequalities in Scotland and benchmark performance

This project will develop a modelling framework to explain changes in income-related health inequalities and benchmark the performance of Scotland in tackling income-related health inequalities, both over time and relative to that of England and Wales.

Organizational form and business performance

This project deals with the generation of profitability and the distribution of its benefits. Inspired by Davis (1947, 1955), we define profitability as the ratio of revenue to cost. Profitability is not as popular a measure of business financial performance as profit, the difference between revenue and cost. Regardless of its popularity, however, profitability is surely a useful financial performance measure. Our primary objective in this project is to identify the factors that generate change in profitability. One set of factors, which we refer to as sources, consists of changes in quantities and prices of outputs and inputs. Individual quantity changes aggregate to the overall impact of quantity change on profitability change, which we call productivity change. Individual price changes aggregate to the overall impact of price change on profitability change, which we call price recovery change. In this framework profitability change consists exclusively of productivity change and price recovery change. A second set of factors, which we refer to as drivers, consists of phenomena such as technical change, change in the efficiency of resource allocation, and the impact of economies of scale. The ability of management to harness these factors drives productivity change, which is one component of profitability change. Thus the term sources refers to quantities and prices of individual outputs and inputs, whose changes influence productivity change or price recovery change, either of which influences profitability change. The term drivers refers to phenomena related to technology and management that influence productivity change (but not price recovery change), and hence profitability change.

Forensic examination of ink by high-performance thin layer chromatography - The United States Secret Service Digital Ink Library

Forensic examinations of ink have been performed since the beginning of the 20th century. Since the 1960s, the International Ink Library, maintained by the United States Secret Service, has supported those analyses. Until 2009, the search and identification of inks were essentially performed manually. This paper describes the results of a project designed to improve ink samples' analytical and search processes. The project focused on the development of improved standardization procedures to ensure the best possible reproducibility between analyses run on different HPTLC plates. The successful implementation of this new calibration method enabled the development of mathematical algorithms and of a software package to complement the existing ink library.

Myocardial Ischaemia National Audit Project (MINAP)

The Myocardial Infarction Audit Project (MINAP) began in late 1998 when a broadly based steering group developed a dataset for acute myocardial infarction (AMI). This allowed clinicians to examine the management of myocardial infarction within their hospitals against targets specified by the National Service Framework for Coronary Heart Disease (NSF). The audit project produces annual reports "How the NHS manages heart attacks" to show the performance of hospitals, ambulance services and cardiac networks in England and Wales against national standards and targets for the care of heart attack patients. MINAP has recently changed its name from the Myocardial Infarction National Audit Project to the Myocardial Ischaemia National Audit Project to reflect the importance of all acute coronary syndromes.

The Network Company in Catalonia : ICT, Productivity, Competitiveness, Salaries and Performance in Catalonia's Companies. Research report (synthesis document)

Resum en anglès del projecte de recerca L'empresa xarxa a Catalunya. TIC, productivitat, competitivitat, salaris i beneficis a l'empresa catalana té com a objectiu principal constatar que la consolidació d'un nou model estratègic, organitzatiu i d'activitat empresarial, vinculat amb la inversió i l'ús de les TIC (o empresa xarxa), modifica substancialment els patrons de comportament dels resultats empresarials, en especial la productivitat, la competitivitat, les retribucions dels treballadors i el benefici. La contrastació empírica de les hipòtesis de treball l'hem feta per mitjà de les dades d'una enquesta a una mostra representativa de 2.038 empreses catalanes. Amb la perspectiva de l'impacte de la inversió i l'ús de les TIC no s'aprecia una relació directa entre els processos d'innovació digital i els resultats de l'activitat de l'empresa catalana. En aquest sentit, hem hagut de segmentar el teixit productiu català per a buscar les organitzacions en què el procés de coinnovació tecnològica digital i organitzativa és més present i en què la intensitat de l'ús del coneixement és un recurs molt freqüent per a poder copsar impactes rellevants en els principals resultats empresarials. Això és així perquè l'economia catalana, avui, presenta una estructura productiva dual.

Contribution to Asterisk Open Source Project

With this final master thesis we are going to contribute to the Asterisk open source project. Asterisk is an open source project that started with the main objective of develop an IP telephony platform, completely based on Software (so not hardware dependent) and under an open license like GPL. This project was started on 1999 by the software engineer Mark Spencer at Digium. The main motivation of that open source project was that the telecommunications sector is lack of open solutions, and most of the available solutions are based on proprietary standards, which are close and not compatible between them. Behind the Asterisk project there is a company, Digum, which is the project leading since the project was originated in its laboratories. This company has some of its employees fully dedicated to contribute to the Asterisk project, and also provide the whole infrastructure required by the open source project. But the business of Digium isn't based on licensing of products due to the open source nature of Asterisk, but it's based on offering services around Asteriskand designing and selling some hardware components to be used with Asterisk. The Asterisk project has grown up a lot since its birth, offering in its latest versions advanced functionalities for managing calls and compatibility with some hardware that previously was exclusive of proprietary solutions. Due to that, Asterisk is becoming a serious alternative to all these proprietaries solutions because it has reached a level of maturity that makes it very stable. In addition, as it is open source, it can be fully customized to a givenrequirement, which could be impossible with the proprietaries solutions. Due to the bigness that is reaching the project, every day there are more companies which develop value added software for telephony platforms, that are seriously evaluating the option of make their software fully compatible withAsterisk platforms. All these factors make Asterisk being a consolidated project but in constant evolution, trying to offer all those functionalities offered by proprietaries solutions. This final master thesis will be divided mainly in two blocks totally complementaries. In the first block we will analyze Asterisk as an open source project and Asterisk as a telephony platform (PBX). As a result of this analysis we will generate a document, written in English because it is Asterisk project's official language, which could be used by future contributors as an starting point on joining Asterisk. On the second block we will proceed with a development contribution to the Asterisk project. We will have several options in the form that we do the contribution, such as solving bugs, developing new functionalities or start an Asterisk satellite project. The type of contribution will depend on the needs of the project on that moment.

Department of Commerce - Iowa Utilities Board, Performance Report, Performance Results Achieved for Fiscal Year 2004, December 2004

The FY04 Performance Report for the Iowa Utilities Board (IUB) highlights the services the IUB provided to Iowans, along with results achieved to ensure utility service reliability and to improve and expand utility service infrastructure in Iowa. This information is provided in accordance with the State of Iowa Accountable Government Act, Iowa Code chapter 8E. The two basic business functions of the IUB are utility regulation and compliance, and resource management. This report covers performance information for both of these areas.