Study of the thermal stress in a Pb-free half-bump solder joint under current stressing

The thermal stress in a Sn3.5Ag1Cu half-bump solder joint under a 3.82×108 A/m2 current stressing was analyzed using a coupled-field simulation. Substantial thermal stress accumulated around the Al-to-solder interface, especially in the Ni+(Ni,Cu)3Sn4 layer, where a maximal stress of 138 MPa was identified. The stress gradient in the Ni layer was about 1.67×1013 Pa/m, resulting in a stress migration force of 1.82×10-16 N, which is comparable to the electromigration force, 2.82×10-16 N. Dissolution of the Ni+(Ni,Cu)3Sn4 layer, void formation with cracks at the anode side, and extrusions at the cathode side were observed

Arsenic influence on genetic variation in grain trace-element nutrient content in Bengal delta grown rice

It has previously been shown that across different arsenic (As) soil environments, a decrease in grain selenium (Se), zinc (Zn), and nickel (Ni) concentrations is associated with an increase in grain As. In this study we aim to determine if there is a genetic element for this observation or if it is driven by the soil As environment. To determine the genetic and environmental effect on grain element composition, multielement analysis using ICP-MS was performed on rice grain from a range of rice cultivars grown in 4 different field sites (2 in Bangladesh and 2 in West Bengal). At all four sites a negative correlation was observed between grain As and grain Ni, while at three of the four sites a negative correlation was observed between grain As and grain Se and grain copper (Cu). For manganese, Ni, Cu, and Se there was also a significant genetic interaction with grain arsenic indicating some cultivars are more strongly affected by arsenic than others.

Contaminants in surface water and sediments around the Tynagh Mine, Galway, Ireland.

A former silver mine in Tynagh, Co. Galway, Ireland is one of the most contaminated mine sites in Europe with maximum concentrations of Zn, As, Pb, Mn, Ni, Cu, and Cd far exceeding guideline values for water and sediment. The aims of this research were to 1) further assess the contamination, particularly metals, in surface water and sediment around the site, and 2) determine if the contamination has increased 10 years after the Environmental Protection Agency Ireland (EPAI) identified off-site contamination. Site pH is alkaline to neutral because CaCO3-rich sediment and rock material buffer the exposed acid generating sulphide-rich ore. When this study was compared to the previous EPAI study conducted 10 years earlier, it appeared that further weathering of exposed surface sediment had increased concentrations of As and other potentially toxic elements. Water samples from the tailings ponds and adjacent Barnacullia Stream had concentrations of Al, Cd, Mn, Zn and Pb above guideline values. Lead and Zn concentrations from the tailings pond sediment were 16 and 5 times higher, respectively, than concentrations reported 10 years earlier. Pb and Zn levels in most sediment samples exceeded the Expert Group (EGS) guidelines of 1000 and 5000 mg/kg, respectively. Arsenic concentrations were as high as 6238 mg/kg in the tailings ponds sediment, which is 62 and 862 times greater than the EGS and Canadian Soil Quality Guidelines (CSQG), respectively. Cadmium, Cu, Fe, Mn, Pb and Zn concentrations in water and sediment were above guideline values downstream of the site. Additionally, Fe, Mn and organic matter (OM) were strongly correlated and correlated to Zn, Pb, As, Cd, Cu and Ni in stream sediment. Therefore, the nearby Barnacullia Stream is also a significant pathway for contaminant transport to downstream areas. Further rehabilitation of the site may decrease the contamination around the area.

Levels of Arsenic and Other Trace Elements in Southern Libyan Agricultural Irrigated Soil and Non-irrigated Soil Projects

The levels of As and various other trace elements found in the irrigated agricultural soil (Tsoil) of southern Libya were compared with non-irrigated soil (Csoil) from the same sampling campaign collected between April and May 2008. The soil samples represented agronomic practice in the southern Libyan regions of Maknwessa (MAK), Aril (ARL) and Taswaa (TAS), and were analyzed by Inductively coupled plasma mass spectrometry (ICP-MS) for Co, Ni, Cu, Se, Mo, Zn, As, Pb, Cd and P. Concentrations of P and As in TAS and MAK were found to be higher in Tsoil compared to Csoil, while the opposite was true for ARL. In general, As concentrations in these areas were 2-3 times lower than the global average. In ARL, the average P concentrations of the Csoil samples were significantly higher than those of Tsoil samples: this site is composed mainly of pasture for animal production, where phosphate fertilizers are used regularly. Distance from the source of irrigation was found to be of an important influence on the heavy metal concentration of the soil, with greater concentrations found closer to the irrigation source. It can be concluded from the results that irrigation water contains elevated levels of As, which finds its way into the soil profile and can lead to accumulation of As in the soil over time.

Distribuição por tamanhos do aerosol atmosférico na Península Ibérica

Um dos principais fatores que afetam negativamente a qualidade do ambiente em muitas cidades em todo o mundo é o material particulado (PM). A sua presença na atmosfera pode ter impactos negativos na saúde humana, clima, património edificado e ecossistemas. Muitos dos estudos realizados em áreas urbanas focam apenas as frações respiráveis (PM10 e PM2,5). No entanto, os processos de formação, a identificação das fontes emissoras e os efeitos dependem muito da distribuição granulométrica das partículas. A atenção tem recaído na análise de hidrocarbonetos poliaromáticos (PAHs), devida à sua carcinogenicidade e a informação disponível sobre outros compostos é escassa. O presente estudo consistiu na obtenção do PM distribuído por diferentes frações de tamanho e na análise detalhada da sua composição química, em dois locais urbanos da Península Ibérica (Madrid e Lisboa). Dado que os veículos representam uma das principais fontes emissoras em ambientes urbanos, efetuou-se uma caracterização mais detalhada deste tipo de emissões, conduzindo uma campanha de amostragem num túnel rodoviário (Marquês de Pombal, Lisboa). As amostragens, em ambas as cidades, decorreram durante um mês, quer no verão quer no inverno, em dois locais urbanos distintos, um junto a uma via com influência de tráfego e outro numa área urbana de fundo. No túnel a amostragem foi realizada apenas durante uma semana. Em Madrid e no túnel, o PM foi recolhido utilizando um amostrador de elevado volume com impactor em cascata com quatro tamanhos: 10-2,5, 2,5-0,95, 0,95-0,49 e < 0,49 μm. Em Lisboa, foi utilizado um impactor em cascata com apenas dois tamanhos, 10- 2,5 e < 2,5 μm. As amostras foram quimicamente analisadas e determinadas as concentrações de compostos carbonados (OC, EC e carbonatos), iões inorgânicos solúveis em água (Cl−, NO3−, SO42−, Na+, NH4+, K+, Mg2+, Ca2+),metais e compostos orgânicos. Em Madrid, as concentrações médias de PM10 foram 44 e 48% maiores nas amostras recolhidas junto à estrada do que as de fundo urbano no verão e inverno, respetivamente. A fração grosseira e o PM0,5 apresentaram concentrações mais elevadas no verão do que no inverno devido às condições climatéricas pouco usuais. No verão, as amostragens decorreram num mês em que as temperaturas foram muito elevadas e em que ocorreram vários episódios de intrusão de poeira africana. Durante o período de amostragem de inverno, as temperaturas foram muito baixas e registaram-se vários dias de precipitação quer sob a forma de chuva, quer sob a forma de neve. As situações meteorológicas sinóticas mais comuns, incluindo aquelas que causam o transporte de massas de ar com poeiras Africanas, foram identificadas em ambas as estações do ano. As concentrações mássicas de PM10, EC e OC foram encontrados predominantemente na fração de tamanho ultrafino em ambos os locais de amostragem e estações do ano. Nas restantes frações não se observou nenhuma tendência sazonal. O carbono orgânico secundário (SOC) mostrou um claro padrão sazonal, com concentrações muito mais elevadas no verão do que no inverno, em ambos os lugares. A partir do balanço mássico de iões, observou-se que, no verão, a formação de compostos inorgânicos secundários (SIC) conduziu a um enriquecimento pouco comum de Ca2+ na fração submicrométrica, quer nas amostras de tráfego, quer em fundo urbano. Os alcanos, PAHs, os álcoois e os ácidos foram as classes de compostos orgânicos identificados e quantificados no material particulado. Globalmente, representaram 0,26 e 0,11 μg m−3 no verão e inverno, respetivamente, no local de tráfego e 0,28 e 0,035 μg m−3 na área urbana de fundo. Os diferentes compostos orgânicos também apresentaram padrões sazonais, sugerindo fontes de emissão (e.g. escapes dos veículos e fontes biogénicas) ou processos de formação com contribuições variáveis ao longo do ano. As concentrações de benzoapireno equivalente foram menores que 1 ng m-3 e o risco carcinogénico estimado é baixo. No verão, os maiores enriquecimentos de metais ocorreram na fração submicrométrica, e no inverno na fração grosseira. No verão, os enriquecimentos foram ≥ 80% para o Mn, Ni, Cu, Zn, Cd, Sb e Co, no inverno, estes traçadores de emissões do tráfego foram menores, exceto para o Zn. Em Lisboa, a concentração média de PM10 foi de 48 μg m-3 no verão e de 44 μg m-3 no inverno, junto à estrada. Na área de fundo urbano, registaram-se níveis comparáveis nas duas estações (27 μg m-3 e 26 μg m-3). A média do rácio PM2,5/PM10 foi de 65% no verão e 44% no inverno na área de tráfego e 62% e 59% na área urbana de fundo. Estes resultados significam que o PM2,5 é um dos principais contaminantes que afetam a qualidade do ar no centro da cidade de Lisboa. A relação OC/EC, que reflete a composição das emissões de combustão dos veículos, variou entre 0,3 e 0,4 no interior do túnel. Os rácios de OC/EC mínimos obtidos junto às vias de tráfego em Madrid e em Lisboa encontram-se entre os do túnel e os registados em atmosferas urbanas de fundo, sugerindo que os valores mínimos habitualmente obtidos para este parâmetro em ambientes urbanos abertos sobrestimam as emissões diretas de OC pelo transporte rodoviário. Espera-se que os resultados deste trabalho contribuam para suprir, pelo menos em parte, as lacunas de informação quer sobre a composição de várias granulometrias de PM, quer sobre fontes e processos de formação em atmosferas urbanas. Como a exposição a poluentes do ar ultrapassa o controle dos indivíduos e exige ação das autoridades públicas a nível nacional, regional e até mesmo internacional, é importante propor medidas mitigadoras focadas nas principais fontes de emissão identificadas.

Contributo da geoquímica e da sedimentologia na caracterização de influências antropogénicas em ambientes estuarinos

Tese de doutoramento, Geologia (Geoquímica), Universidade de Lisboa, Faculdade de Ciências, 2016

Dynamics And Speciation Of The Heavy Metals In The Lower Reaches Of Chithrapuzha- A Tropical Tidal River

The proposed study is an attempt to quantify and study the seasonal and spatial variations in the distribution of Cr, Mn, Fe, Co, Ni, Cu, Zn, Cd and Pb among the various geochemical phases in the surficial sediments of Chitrapuzha river. The study also estimates the concentration of heavy metals in dissolved, particulate and sediments and their variation in seasonal and spatial distribution. Chitrapuzha River originates as a small stream from the upper reaches of high ranges in the eastern boundary of Kerala, passes through the valley and finally joints in the Cochin backwaters. Numerous industrial units located along the banks of the river discharge treated and untreated effluents into the water. These are long standing local complaints about water pollution causing fish mortality and serious damage to agricultural crops resulting in extensive unemployment in the area. The river is thus of considerable social and economic importance.

Influvence of Alloying Additions on the Structure and Properties of Ai-7Si-0.3Mg Alloy

Cast Ai-Si alloys are widely used in the automotive, aerospace and general engineering industries due to their excellent combination of properties such as good castability, low coefficient of thermal expansion, high strength-to-weight ratio and good corrosion resistance. The present investigation is on the influence of alloying additions on the structure and properties of Ai-7Si-0.3Mg alloy. The primary objective of this present investigation is to study these beneficial effects of calcium on the structure and properties of Ai-7Si-0.3Mg-xFe alloys. The second objective of this work is to study the effects of Mn,Be and Sr addition as Fe neutralizers and also to study the interaction of Mn,Be,Sr and Ca in Ai-7Si-0.3Mg-xFe alloys. In this study the duel beneficial effects of Ca viz;modification and Fe-neutralization, comparison of the effects of Ca and Sr with common Fe neutralizers. The casting have been characterized with respect to their microstructure, %porosity and electrical conductivity, solidification behaviour and mechanical properties. One of the interesting observations in the present work is that a low level of calcium reduces the porosity compared to the untreated alloy. However higher level of calcium addition lead to higher porosity in the casting. An empirical analysis carried out for comparing the results of the present work with those of the other researchers on the effect of increasing iron content on UTS and % elongation of Ai-Si-Mg and Ai-Si-Cu alloys has shown a linear and an inverse first order polynomial relationships respectively.

Surface Properties and Catalytic Activity of Manganese Ferrospinels

In recent years considerable advances have been achieved in the study of the surface structure and mechanism of action of environmentally benign heterogeneous catalysts. The study entitled as surface properties and catalytic activity of manganese ferrospinels. In the present study we have prepared manganese ferrospinels of general formula Mn(1-x)BxFe2O4 via low temperature controlled co-precipation method. The study employed low temperature co-precipitation method for the preparation ofMn(1-x)BxFe2O4 specimens, where B is a metal cation such as Cr,Co, Ni,Cu and Zn. The catalytic activities of the systems were investigated for liquid-phase benzoylation of aromatic compounds and phenol hydroxylation and for vapour-phase reactions such as aniline alkylation, phenol methylation and ODH of ethylbenzene. The different series of manganese ferrites are proved to be excellent catalysts for various industrially important reactions such as Friedel-crafts benzoylation of aromatic compounds, methylation of aniline and phenol, hydroxylation of phenol and oxidative dehydrogenation of ethylbenzene. Due to the tightening of the environmental regulations, production of diphenols from phenol hydroxylation and reduction of phenolic pollutants in waste waters using these catalysts can be a promising approach because it demands only simple techniques and produce little environmental pollution.

Precursor nanoscale modulations in ferromagnets: Modeling and thermodynamic characterization

Using a Ginzburg-Landau model for the magnetic degrees of freedom with coupling to disorder, we demonstrate through simulations the existence of stripelike magnetic precursors recently observed in Co-Ni-Al alloys above the Curie temperature. We characterize these magnetic modulations by means of the temperature dependence of local magnetization distribution, magnetized volume fraction, and magnetic susceptibility. We also obtain a temperature-disorder strength phase diagram in which a magnetic tweed phase exists in a small region between the paramagnetic and dipolar phases.

Chemometric study on the trace metal accumulation in the sediments of the Cochin Estuary―Southwest coast of India

The distribution and accumulation of trace metals in the sediments of the Cochin estuary during the pre-monsoon, monsoon and post-monsoon periods were investigated. Sediment samples from 14 locations were collected and analysed for the metal contents (Mg, Cr, Mn, Fe, Co, Ni, Cu, Zn, Cd and Pb), organic carbon, total nitrogen, total sulphur and grain size. The data were processed using statistical tools like correlation, factor and cluster analysis. The study revealed an enrichment of Cd and Zn in the study area particularly at station 2, which is confirmed by enrichment factor, contamination factor and geoaccumulation index. The factor analysis revealed that the source of Cd and Zn may be same. The study indicated that the spatial variation for the metals like Mg, Cr, Fe, Co, Ni, Cu, Zn, Cd and Pb were predominant unlike Mn which shows a temporal variation. The strong association of trace metals with Fe and Mn hydroxides and oxides are prominent along the Cochin estuary. The anthropogenic inputs of industrial effluents mainly control the trace metals enrichment in the Cochin estuary

Trace elements biogeochemistry in high mountain lake catchments: identifying anthropogenic versus natural components from the atmospheric contamination legacy in remote natural areas

Human activities have been interfering with the natural biogeochemical cycles of trace elements since the ancient civilizations. Although they are inaccessible and remote, high mountain lake catchments are irrefutably trace-element contaminated by anthropogenic emissions, which can travel by long-range atmospheric transport before they are deposited. This has been revealed by several natural archives. High mountain lake catchments are thus excellent sentinels of long-range contamination. Continuous accumulation can lead to a build up of potentially toxic trace elements in these remote, or relatively remote, ecosystems. The thesis focuses on the biogeochemistry of a suite of trace elements of environmental concern (Ni, Cu, Zn, As, Se, Cd and Pb) in Pyrenean lake catchments, with special emphasis on discerning the “natural” components from the “anthropogenic” contributions. Five other metallic elements (Al, Fe, Ti, Mn and Zr) have also been studied to trace natural fluxes and biogeochemical processes within the lake catchment systems.

Distribution of selected heavy metals in sediments of the Agueda river (Central Portugal)

The state of river water deterioration in the Agueda hydrographic basin, mostly in the western part, partly reflects the high rate of housing and industrial development in this area in recent years. The streams have acted as a sink for organic and inorganic loads from several origins: domestic and industrial sewage and agricultural waste. The contents of the heavy metals Cr, Cd, Ni, Cu, Pb, and Zn were studied by sequential chemical extraction of the principal geochemical phases of streambed sediments, in the <63 mum fraction, in order to assess their potential availability to the environment, investigating, the metal concentrations, assemblages, and trends. The granulometric and mineralogical characteristics of this sediment fraction were also studied. This study revealed clear pollution by Cr, Cd, Ni, Cu, Zn, and Pb, as a result from both natural and anthropogenic origins. The chemical transport of metals appears to be essentially by the following geochemical phases, in decreasing order of significance: (exchangeable + carbonates) much greater than (organics) much greater than (Mn and Fe oxides and hydroxides). The (exchangeable + carbonate) phase plays an important part in the fixation of Cu, Ni, Zn, and Cd. The organic phase is important in the fixation of Cr, Pb, and also Cu and Ni. Analyzing the metal contents in the residual fraction, we conclude that Zn and Cd are the most mobile, and Cr and Pb are less mobile than Cu and Ni. The proximity of the pollutant sources and the timing of the influx of contaminated material control the distribution of the contaminant-related sediments locally and on the network scale.

Mineral and geochemical characterization of a leptic aluandic soil and a thapto aluandic-ferralsol developed on trachytes in Mount Bambouto (Cameroon volcanic line)

Mineral and geochemical investigations were carried out on soil samples and fresh rock (trachytes) from two selected soil profiles (TM profile on leptic aluandic soils and TL profile on thapto aluandic-ferralsols) from Mount Bambouto to better understand geochemical processes and mineral paragenesis involved in the development of soils in this environment. In TM profile, the hydrated halloysites and goethite occur in the weathered saprolite boulders of BC horizon while dehydrated halloysite, gibbsite and goethite dominate the soils matrices of BC and A horizons. In TL profile, the dehydrated halloysites and goethite are the most abundant secondary minerals in the weathered saprolites of C and BC horizons while gibbsite, hematite and kaolinite occur in the soil matrices of BC, B and A horizons. The highest gibbsite content is in the platy nodules of B horizon. In both soil profiles, organo-metal complexes (most likely of AI and Fe) are present in the surface A horizon. Geochemically, between the fresh rock and the weathered saprolites in both soils, SiO2, K2O, CaO, Na2O and MgO contents decrease strongly while Fe2O3 and Al2O3 tend to accumulate. The molar ratio of SiO2/Al2O3 (Ki) and the sum of Ca, Mg, K and Na ions (TRB) also decreases abruptly between fresh rocks and the weathered saprolites, but increases significantly at the soil surface. The TM profile shows intense Al enrichment whereas the TL profile highlights enrichment in both AI and Fe as the weathering progresses upwards. Both soil profiles are enriched in Ni, Cu, Ba and Co and depleted in U, Th, Ta, Hf, Y, Sr, Pb, Zr and Zn relative to fresh rock. They also show a relatively low fractionation of the rare earth elements (REE: La, Nd, Sm, Eu, Tb, Yb and Lu), except for Ce which tends to be enriched in soils compared to CI chondrite. All these results give evidence of intense hydrolysis at soil deep in Mount Bambouto resulting in the formation of halloysite which progressively transforms into gibbsite and/or dehydrated halloysite. At the soil surface, the prominent pedogenetic process refers to andosolization with formation of organo-metal complexes. In TL profile, the presence of kaolinite in soil matrices BC and B horizons is consistent with ferralitization at soil deep. In conclusion, soil forming processes in Mount Bambouto are strongly influenced by local climate: (i) in the upper mountain (>2000 m), the fresh, misty and humid climate favors andosolization; whereas (ii) in the middle lands (1700-2000 m) with a relatively dry climate, both andosolization at the soil surface and ferralitization at soil deep act together. (C) 2009 Elsevier B.V. All rights reserved.

Extended-chain, multinuclear transition metal complexes bridged by cyanodiazenido(1-), [N=N-C=N](-), ligands

Extended-chain complexes containing multiple transition metal centres linked by conjugated mu-cyanodiazenido(1-) ligands [N= N-C N]-have been obtained by reaction of trans-[BrW(dppe)(2)(N2CN)], 1, [dppe = 1,2-bis(diphenylphosphino) ethane] with dirhodium(II) tetra-acetate, bis(benzonitrile) palladium(II) dichloride, and bis(aqua) M(II) bis(hexa. uoroacetylacetonate) (M = Mn, Ni, Cu, Zn): stronger Lewis acids such as tetrakis(acetonitrile) palladium(II) tetra. uoroborate and boron trifl. uoride promote hydrolysis of complex 1, leading to the isolation of a novel carbamoylhydrazido(2-) complex, trans-[BrW(dppe) 2(N2HC=ONH2)](+)[BF4](-).