Perfil mutacional do gene APC em pacientes com polipose adenomatosa familial no estado do Pará

O câncer colorretal é um grave problema de saúde pública na região norte, sendo a 3a neoplasia mais frequente entre os homens e a 2a entre as mulheres. Cerca de 10% destes tumores são hereditários e a polipose adenomatosa familial está entre as principais causas destes. Mutações no gene APC são responsáveis pelo desenvolvimento de tumores nestes pacientes e estão presentes desde a fase mais precoce na carcinogênese, além disso, existe uma relação entre o tipo de mutação e apresentação clínica da doença. Até o presente momento não existe uma publicação com o perfil de mutação do gene APC na região norte do país. Este trabalho tem como objetivo principal, identificar o perfil de mutações no gene APC em famílias do estado do Pará. Um total de 15 pacientes foi analisado provenientes de cinco famílias, todos atendidos no UNACON do HUJBB. Foi realizado a extração de DNA do sangue periférico e realizado um sequenciamento direto em um membro de cada família, obtendo desta forma um screening molecular e os demais membros da família foram genotipados pela técnica ARMS. A análise estatística foi realizada pelos softwares que acompanham o próprio produto. Neste estudo foram encontrados mutações nos 15 membros estudados (provenientes das 5 famílias), 40% das quais eram do tipo frameshift, 35% silenciadoras e 20% nonsense. Sendo que 60% de todas as mutações ocorreram na região MCR. Entre as três mutações mais frequentes na literatura, neste estudo foram encontradas duas: códon 1309 (em 40% dos indivíduos) e no códon 1061 (em 10% dos indivíduos). Estes números foram bem diferentes dos encontrados na literatura, reforçando o papel da miscigenação na frequência das mutações. A mutação c.3956delC foi a única encontrada em todas as famílias analisadas, o que pode comportar-se como um forte biomarcador desta síndrome. A avaliação clínica dos pacientes confirmou a correlação genótipo/fenótipo, sendo um fator determinante para o direcionamento clínico e aconselhamento genético. A plataforma confeccionada para análise de mutações pela técnica ARMS será de grande utilidade, já que conseguiu detectar mutações no 15 indivíduos estudados a um custo bem inferior que o sequenciamento direto por PCR.

Avaliação técnica e econômica de sistemas de produção da cana-de-açúcar (Saccharum spp) convencional e orgânica na região oeste do Estado de São Paulo

Pós-graduação em Agronomia - FEIS

Caracterização funcional e estrutural de uma ?-glucanase GH12 de Aspergillus terreus

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Desenvolvimento de sensor baseado em eletrodo modificado com nanotubos de carbono contendo pentacianonitrosilferratos de metais para determinação de antioxidantes em microemulsão de biodiesel

Pós-graduação em Química - IQ

Palatabilizantes em dietas de leitões recém-desmamados

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Impacto da adição de caulim nas propriedades físico-mecânicas do papel formado por sequências ECF

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Avaliação do desempenho operacional e de custos entre enfardadoras no recolhimento de palhiço de cana-de-açúcar

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Estudo comparativo entre MDF e MDP utilizados na indústria moveleira

Increasingly, the furniture market is competitive. The construction industry presents itself in growth, mainly due to the lines of existing incentives and tax credits established by the government, assisting the impulse to purchase real estate, building materials and furniture. Factors that promote and strengthen the sector's growth. With high demand from the furniture market, demand for higher quality and increasing technological advances, research is often undertaken in search of solutions for process improvement and product features, focusing on the production of materials less harmful to the environment, provision of raw press to lower cost, improve the production process and product development of cost-effective. This research focuses on the comparative study between two materials widely used in furniture manufacturing. MDF (Medium Density Fiberboard) and MDP (Medium Density Particleboard). The subject provides the focus in furniture production, presenting and comparing data collected from three companies producing panels between physical and mechanical characteristics of the materials, also presenting some of the main factors of influence on the quality of the panels, their features and applications on mobile. The study shows the high potential of using the MDP (Medium Density Particleboard) in furniture designs, as well as MDF (Medium Density Particleboard), favoring the final terms of the project , resulting in better utilization of each material , avoiding waste and increase unnecessary cost . Currently, several projects are developed in MDP and MDF furniture, where there is no relevance to their characteristics regarding their limitations. Many of these furnishings are designed without a specific study of the best use and positioning of each material, with better utilization , favoring collateral design , especially furniture designed exclusively for each environment . The lack of technical ...

Utilização do método AHP para análise de alterações de projetos, em instalações hospitalares

Customer focus , high competitiveness and striving for excellence in quality of service are some of the main features of the current market . Planned and make decisions with greater certainty is no longer an option a few years . The current managers are seeking ways to eliminate waste and increase financial and productive profitability of your company in order to achieve higher performance at a lower cost . The AHP is one of the main concepts of this goal by providing an analysis on multiple criteria , enhancing decision-making and enhancing the gains , with a technique that is designed to take into account all the key criteria for choosing an alternative , according to the perspective of the designer as both suppliers and customers . Emerging as a new way to minimize errors , and make an informed and consistent decision. The use of this method in construction projects is a recent phenomenon , which has much to be explored , an intense analysis of the processes is required to enable it to consider the concepts and present a consistent and grounded proposal

Estudo e seleção de um aparelho de ar condicionado para ônibus

The study and selection of an equipment of air conditioner for any type of environment, should be made without overestimate or undersizing the project. The undersizing does not provide an adequate comfort temperature if the environment is too hot because the air conditioner does not remove all the heat necessary in the environment. But if the project is oversized, energy consumption is higher and there is an unnecessary cost. To prevent these failures is necessary to make a calculation of the thermal load on the environment and choose the equipment that has a higher cooling capacity than the calculated heat load and closer to the calculated heat load. In this graduate work will be chosen an air-conditioned equipment for bus, showing the calculations made for the thermal load for various types of heat gain in this type of vehicle. The thermal load on vehicles is more complicated to calculate than in areas because there are several factors that vary with the movement of the vehicle. It will also explain the compression refrigeration cycle, which is the cooling system used in vehicles because it is weightless, compact and lower cost. From the calculated heat load, it will be chosen an air conditioner that best suits the project and, finally, a brief presentation of the selected equipment will be made

Sintese e caracterização da resina fenol-furfurílica para a obtenção de carbono vítreo monolítico

The monolithic glassy carbon is a carbonaceous material, isotropic, non graphitizable obtained by means of carbonization of resins up to 1000 °C. The good physicochemical properties make this material applied in several areas such as aerospace, medicine, electronics, chemistry, among others. It has generally been processed from the use of phenolic and furfuryl alcohol resins. These resins have high crosslink density and high fixed carbon content and are therefore widely applied in aerospace. The combination phenol / furfuryl alcohol resins search for obtaining the most suitable process for the glass-like carbon processing with phenolic resins currently available and of lower cost and easier to synthesize than the furfuryl alcohol resin. The main objective of this work is to obtain a phenol-furfuryl resin with high fixed carbon content combined with low porosity of the material. Different synthesis routes have been adopted along with thermal analysis techniques, FTIR and image analysis. The resin obtained through partial synthesis process presented the characteristics sought in this work

Otimização da extração alcalina com peróxido de hidrogênio em seqüência de branqueamento com aplicação de baixo fator kappa

The new market, focused on sustainability and other environmental concerns, refers to innovations that seek alternative forms of production. In pulp and paper bleaching alternative reagents are studied, for example, hydrogen peroxide, in partial substitution of chlorine dioxide in order to reduce the formation of organochlorines. In this context, this study examined the burden of hydrogen peroxide (H2O2) on alkaline extraction stage (stage Ep) required for the bleaching of pulp with eucalyptus kraft pulp, pre-oxygen delignified to obtain equivalent brightness at 90 ± 0.5% ISO, as well as its effect on quality of pulp produced. The pulp was bleached by the sequence D(Ep)DP, with the application of factor kappa of 0.14 and varying the concentration of hydrogen peroxide in Ep stage three, five, seven and nine kilograms of reagent per ton of pulp absolutely drought. The final P stage was optimized with the use of six, nine and twelve pounds of hydrogen peroxide per ton of absolutely dry pulp to achieve the required brightness. The quality of the pulp produced was analyzed based on the kappa number, the brightness and the viscosity. The methods were performed according to standards set by the standard TAPPI (Technical Association of the Pulp and Paper Industry). The best result was obtained using the following D0Ep(7)D1P(6), which showed a viscosity of 19.9 cP, 89.6% ISO brightness, consumption of 94.9 kg / t of reagents and reagent costs of US$ 28.15, because it showed better pulp quality for a lower cost compared to the others. It was found that the greater the amount of hydrogen peroxide in alkaline extraction, the lower the kappa number and increased the amount of residual hydrogen peroxide. The higher the charge of hydrogen peroxide in Ep stage, the lower the need for hydrogen peroxide in the final P stage, reducing the cost of bleaching

Transnacionalização das relações de trabalho: o caso da maquila estadunidense Johnson Controls (plantas FINSA e interiores) e o papel da Federação Internacional de Trabalhadores das Indústrias Metalúrgicas (FITIM)

Pós-graduação em Relações Internacionais (UNESP - UNICAMP - PUC-SP) - FFC

Natural compounds isolated from Brazilian plants are potent inhibitors of hepatitis C virus replication in vitro

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Aços avançados de alta resistência: avaliação da microestrutura e propriedades dos aços DP 600 E DP 780

This work aims to study the Dual-Phase 600 and 780 steels, which are part of technology development project materials for the automotive industry. It is worth underscoring the antagonistic properties as the Dual-Phase steel assemble, high mechanical strength and elongation due its microstructure, ferrite and martensite. These properties are obtained by a intercritical heat treatment which facilitates the formation of a hardness metastable microstructure shaped plates of low carbon steels. The applicability of Dual Phase steel in the structure of vehicles is huge and its production is already on a commercial scale, so the study and development of this material implies lower cost in automobile manufacturing processes. The dual phase steels DP600 and DP780 underwent tensile, hardness and metallographic analysis to evaluate and comparing its properties. The results indicate that the DP780 steel has higher strength and hardness than the DP600 steel and its microstructure consists of martensite higher fraction which accounts for the higher resistance and hardness. However, the DP600 has higher conformability to DP780 steel