Influences of CO2 laser irradiation on the structure and photoluminescence of zinc oxide thin films

CO2 laser irradiation experiments on ZnO thin films are reported. The structural, optical, luminescent and vibrational properties of the samples were investigated by X-ray diffraction (XRD), transmittance, photoluminescence (PL) and Raman measurements. XRD results show that the crystalline of the irradiated films was improved. The (002) peaks of irradiated ZnO films shift to. higher 20 angles due to the stress relaxation in the case of laser beam irradiation. From optical transmittance spectra, all films exhibit high transmittance in the visible range, the optical band edge of irradiated films showed a redshift compared with that of as-grown films. Compared with the as-grown films, the photoluminescence emission (in particular the relative intensities of visible emissions) intensities of irradiated samples enhanced. In the Raman scattering spectral both the A I. and E modes exhibited slight Raman blueshift. (c) 2005 Elsevier B.V. All rights reserved.

High sensitive NO2 gas sensor with low power consumption using selectively grown ZnO nanorods.

The noble gas sensor using multiple ZnO nanorods was fabricated with CMOS compatible process and sol-gel growth method on selective area and gas response characteristics to NO2 gas of the sensor device were investigated. We confirmed the sensors had high sensitive response denoted by the sensitivity of several tens for NO2 gas sensing and also showed pretty low power consumption close to 20 mW even though the recovery of resistance come up to almost the initial value.

High power laser with integrated lens using focused ion beam etching

In this study, a collimating lens is introduced at the output facet of a tapered waveguide laser to compensate for the divergence of the optical mode. The collimating lens is shown to enhance the laser efficiency while simultaneously reducing the far field divergence.

A new low-power highly linear mixer design using differential derivative superposition

This paper presents the analysis and design of a new low power and highly linear mixer topology based on a newly reported differential derivative superposition method. Volterra series and harmonic balance are employed to investigate its linearisation mechanism and to optimise the design. A prototype mixer has been designed and is being implemented in 0.18μm CMOS technology. Simulation shows this mixer achieves 19.7dBm IIP3 with 10.5dB conversion gain, 13.2dB noise figure at 2.4GHz and only 3.8mW power consumption. This performance is competitive with already reported mixers.

A high temperature and low power SOI CMOS MEMS based thermal conductivity gas sensor

The design, 3D FEM modelling and measurement results of a novel high temperature, low power SOI CMOS MEMS thermal conductivity gas sensor are presented here. The sensor consists of a circular membrane with an embedded tungsten micro-heater. The high sensing capability is based on the temperature sensitivity of the resistive heating element. The sensor was fabricated at a commercial foundry using a 1 μm process and measures only 1×1 mm 2. The circular membrane has a 600 μm diameter while the heating element has a 320 μm diameter. Measurement results show that for a constant power consumption of 75 mW the heater temperature was 562.4°C in air, 565.9°C in N2, 592.5°C for 1 % H2 in Ar and 599.5°C in Ar. © 2013 IEEE.

800V lateral IGBT in bulk Si for low power compact SMPS applications

An 800V rated lateral IGBT for high frequency, low-cost off-line applications has been developed. The LIGBT features a new method of adjusting the bipolar gain, based on a floating N+ stripe in front of the P+ anode/drain region. The floating N+ layer enhances the carrier recombination at the anode/drain side of the drift region resulting in a very significant decrease in the turn-off speed and substantially lower overall losses. Switching speeds as low as 140ns at 25oC and 300ns at 125oC have been achieved with corresponding equivalent Rdson at 125oC below 90mω.cm2. A fully operational AC-DC converter using a controller with an integrated LIGBT+depletion mode MOSFET chip has been designed and qualified in plastic SOP8 packages and used in 5W, 65kHz SMPS applications. The device is fabricated in 0.6μm bulk silicon CMOS technology without any additional masking steps. © 2013 IEEE.

Monolithic MZI-SOA hybrid switch for low-power and low-penalty operation.

We report the first experimental demonstration of a monolithically integrated hybrid dilated 2×2 modular optical switch using Mach-Zehnder modulators as low-loss 1×2 switching elements and short semiconductor optical amplifiers to provide additional extinction and gain. An excellent 40 dB cross-talk/extinction ratio is recorded with data-modulated signal-to-noise ratios of up to 44 dB in a 0.1 nm bandwidth. A switching time of 3 ns is demonstrated. Bit error rate studies show extremely low subsystem penalties of less than 0.1 dB, and studies indicate that, by using this hybrid switch building block, an 8×8 port switch could be achieved with 14 dB input power dynamic range for subsystem penalties of less than 0.5 dB.

An ultra-low power CMOS random number generator

This paper proposes an ultra-low power CMOS random number generator (RING), which is based on an oscillator-sampling architecture. The noisy oscillator consists of a dual-drain MOS transistor, a noise generator and a voltage control oscillator. The dual-drain MOS transistor can bring extra-noise to the drain current or the output voltage so that the jitter of the oscillator is much larger than the normal oscillator. The frequency division ratio of the high-frequency sampling oscillator and the noisy oscillator is small. The RNG has been fabricated in a 0.35 mu m CMOS process. It can produce good quality bit streams without any post-processing. The bit rate of this RNG could be as high as 100 kbps. It has a typical ultra-low power dissipation of 0.91 mu W. This novel circuit is a promising unit for low power system and communication applications. (c) 2007 Elsevier Ltd. All rights reserved.

Thermo-optic variable optical attenuator with low power consumption fabricated on silicon-on-insulator by anisotropic chemical etching

A thermo-optic Mach-Zehnder (MZ) variable optical attenuator based on silicon waveguides with a large cross section was designed and fabricated on silicon-on-insulator (SOI) wafer. Multimode interferometers were used as power splitters and combiners in the MZ structure. In order to achieve a smooth interface, anisotropic chemical etching of silicon was used to fabricate the waveguides. Isolating grooves were introduced to reduce power consumption and device length. The device has a low power consumption of 210 mW and a response time of 50 mus. (C) 2004 Society of Photo-Optical Instrumentation Engineers.

Low power 2 x 2 thermo-optic SOI waveguide switch fabricated by anisotropy chemical etching

A 2 x 2 thermo-optic (TO) Mach-Zehnder (MZ) switch based on silicon waveguides with large cross section was designed and fabricated on silicon-on-insulator (SOI) wafer. The multi-mode interferometers (MMI) were used as power splitter and combiner in MZ structure. In order to get smooth interface, anisotropy chemical wet-etching of silicon was used to fabricate the waveguides instead of dry-etching. Additional grooves were introduced to reduce power consumption. The device has a low switching power of 235 mW and a switching speed of 60 mus. (C) 2004 Elsevier B.V. All rights reserved.

Low power-consumption and high response frequency thermo-optic variable optical Attenuators based on silicon-on-insulator materials

A novel silicon-on-insulator thermo-optic variable optical attenuator with isolated grooves based on a multimode interference coupler principle is fabricated by the inductive coupled plasma etching technology. The maximum fibre-to-fibre insertion loss is lower than 2.2 dB, the dynamic attenuation range is from 0 to 30 dB in the wavelength range 1500-1600 nm, and the maximum power consumption is only 140 mW. The response frequency of the fabricated variable optical attenuator is about 30 kHz. Compared to the variable optical attenuator without isolated grooves, the maximum power consumption decreases more than 220 mW, and the response frequency rises are more than 20 kHz.