A study of the aerodynamic characteristics of captor hoods in local exhaust ventilation systems

The research objectives were:- 1.To review the literature to establish the factors which have traditionally been regarded as most crucial to the design of effectlve exhaust ventilation systems. 2. To design, construct, install and calibrate a wind tunnel. 3. To develop procedures for air velocity measurement followed by a comprehensive programme of aerodvnamic data collection and data analysis for a variety of conditions. The major research findings were:- a) The literature in the subject is inadequate. There is a particular need for a much greater understanding of the aerodynamics of the suction flow field. b) The discrepancies between the experimentally observed centre-line velocities and those predicted by conventional formulae are unacceptably large. c) There was little agreement between theoretically calculated and observed velocities in the suction zone of captor hoods. d) Improved empirical formulae for the prediction of centre-line velocity applicable to the classical geometrically shaped suction openings and the flanged condition could be (and were) derived. Further analysis of data revealed that: - i) Point velocity is directly proportional to the suction. flow rate and the ratio of the point velocity to the average face velocity is constant. ii) Both shape, and size of the suction opening are significant factors as the coordinates of their points govern the extent of the effect of the suction flow field. iii) The hypothetical ellipsoidal potential function and hyperbolic streamlines were found experimentally to be correct. iv) The effect of guide plates depends on the size, shape and the angle of fitting. The effect was to very approximately double the suction velocity but the exact effect is difficult to predict. v) The axially symmetric openings produce practically symmetric flow fields. Similarity of connection pieces between the suction opening and the main duct in each case is essential in order to induce a similar suction flow field. Additionally a pilot study was made in which an artificial extraneous air flow was created, measured and its interaction with the suction flow field measured and represented graphically.

The size frequency distributions of beta-amyloid deposit subtypes in Alzheimer's disease

The size frequency distributions of diffuse, primitive and classic beta/A4 deposits was studied in single sections in the hippocampus, parahippocampal gyrus (PHG) and lateral occipitotemporal gyrus (LOT) in five cases of Alzheimer's disease. In most brain regions, the size distribution of the diffuse deposits was significantly different from that of the primitive and classic deposits. The data suggested that larger diffuse deposits appeared to be converted less often into primitive and classic deposits. Significant differences in the size distribution of primitive deposits were commonly observed between brain regions in which there was no difference in the size distribution of the diffuse deposits. Hence, local brain factors may influence the size of diffuse deposit which can be converted into mature amyloid deposit.

Versenyképesség haloptikával – Helyi gazdaságfejlesztési problémák fejlődő városokban = Competitiveness at short range - Local problems of economic development in medium-sized towns

The aim of our research in the first half of 2011 was to find out what were the administrative, regulative and other problems that were specific obstacles to local economic development and what best practices can be found in local economies. During our research we carried out interviews with leaders and local professionals in five medium size towns of Hungary. We stated that the most obstructive factors were the imperfection of vocational training, the excessively bureaucratic administrative proceedings (supplying of data, acquisition of authority permits, the attitude of the authorities, etc.) and the system of application and finding sources of funds. We think that the most innovative solutions are the good examples of the institutionalized co-operation between local governments and local businesses. We've come to the conclusion that there is a need for reducing administrative burdens for the sake of local economic development.

AIDS workplace *policy adoption and implementation in local government: An analysis of departmental variation

This is an empirical study whose purpose was to examine the process of innovation adoption as an adaptive response by a public organization and its subunits existing under varying degrees of environmental uncertainty. Meshing organization innovation research and contingency theory to form a theoretical framework, an exploratory case study design was undertaken in a large, metropolitan government located in an area with the fourth highest prevalence rate of HIV/AIDS in the country. A number of environmental and organizational factors were examined for their influence upon decision making in the adoption/non-adoption as well as implementation of any number of AIDS-related policies, practices, and programs.^ The major findings of the study are as follows. For the county government itself (macro level), no AIDS-specific workplace policies have been adopted. AIDS activities (AIDS education, AIDS Task Force, AIDS Coordinator, etc.), adopted county-wide early in the epidemic, have all been abandoned. Worker infection rates, in the aggregate and throughout the epidemic have been small. As a result, absent co-worker conflict (isolated and negligible), no increase in employee health care costs, no litigation regarding discrimination, and no major impact on workforce productivity, AIDS has basically become a non-issue at the strategic core of the organization. At the departmental level, policy adoption decisions varied widely. Here the predominant issue is occupational risk, i.e., both objective as well as perceived. As expected, more AIDS-related activities (policies, practices, and programs) were found in departments with workers known to have significant risk for exposure to the AIDS virus (fire rescue, medical examiner, police, etc.). AIDS specific policies, in the form of OSHA's Bloodborn Pathogen Standard, took place primarily because they were legislatively mandated. Union participation varied widely, although not necessarily based upon worker risk. In several departments, the union was a primary factor bringing about adoption decisions. Additional factors were identified and included organizational presence of AIDS expertise, availability of slack resources, and the existence of a policy champion. Other variables, such as subunit size, centralization of decision making, and formalization were not consistent factors explaining adoption decisions. ^

Modeled monthly local topographic lapse rates, Pacific Northwest, USA

An emerging approach to downscaling the projections from General Circulation Models (GCMs) to scales relevant for basin hydrology is to use output of GCMs to force higher-resolution Regional Climate Models (RCMs). With spatial resolution often in the tens of kilometers, however, even RCM output will likely fail to resolve local topography that may be climatically significant in high-relief basins. Here we develop and apply an approach for downscaling RCM output using local topographic lapse rates (empirically-estimated spatially and seasonally variable changes in climate variables with elevation). We calculate monthly local topographic lapse rates from the 800-m Parameter-elevation Regressions on Independent Slopes Model (PRISM) dataset, which is based on regressions of observed climate against topographic variables. We then use these lapse rates to elevationally correct two sources of regional climate-model output: (1) the North American Regional Reanalysis (NARR), a retrospective dataset produced from a regional forecasting model constrained by observations, and (2) a range of baseline climate scenarios from the North American Regional Climate Change Assessment Program (NARCCAP), which is produced by a series of RCMs driven by GCMs. By running a calibrated and validated hydrologic model, the Soil and Water Assessment Tool (SWAT), using observed station data and elevationally-adjusted NARR and NARCCAP output, we are able to estimate the sensitivity of hydrologic modeling to the source of the input climate data. Topographic correction of regional climate-model data is a promising method for modeling the hydrology of mountainous basins for which no weather station datasets are available or for simulating hydrology under past or future climates.

Sources and mixing state of size-resolved elemental carbon particles in a European megacity: Paris

An Aerosol Time-Of-Flight Mass Spectrometer (ATOFMS) was deployed to investigate the size-resolved chemical composition of single particles at an urban background site in Paris, France, as part of the MEGAPOLI winter campaign in January/February 2010. ATOFMS particle counts were scaled to match coincident Twin Differential Mobility Particle Sizer (TDMPS) data in order to generate hourly size-resolved mass concentrations for the single particle classes observed. The total scaled ATOFMS particle mass concentration in the size range 150–1067 nm was found to agree very well with the sum of concurrent High-Resolution Time-of-Flight Aerosol Mass Spectrometer (HR-ToF-AMS) and Multi-Angle Absorption Photometer (MAAP) mass concentration measurements of organic carbon (OC), inorganic ions and black carbon (BC) (R2 = 0.91). Clustering analysis of the ATOFMS single particle mass spectra allowed the separation of elemental carbon (EC) particles into four classes: (i) EC attributed to biomass burning (ECbiomass), (ii) EC attributed to traffic (ECtraffic), (iii) EC internally mixed with OC and ammonium sulfate (ECOCSOx), and (iv) EC internally mixed with OC and ammonium nitrate (ECOCNOx). Average hourly mass concentrations for EC-containing particles detected by the ATOFMS were found to agree reasonably well with semi-continuous quantitative thermal/optical EC and optical BC measurements (r2 = 0.61 and 0.65–0.68 respectively, n = 552). The EC particle mass assigned to fossil fuel and biomass burning sources also agreed reasonably well with BC mass fractions assigned to the same sources using seven-wavelength aethalometer data (r2 = 0.60 and 0.48, respectively, n = 568). Agreement between the ATOFMS and other instrumentation improved noticeably when a period influenced by significantly aged, internally mixed EC particles was removed from the intercomparison. 88% and 12% of EC particle mass was apportioned to fossil fuel and biomass burning respectively using the ATOFMS data compared with 85% and 15% respectively for BC estimated from the aethalometer model. On average, the mass size distribution for EC particles is bimodal; the smaller mode is attributed to locally emitted, mostly externally mixed EC particles, while the larger mode is dominated by aged, internally mixed ECOCNOx particles associated with continental transport events. Periods of continental influence were identified using the Lagrangian Particle Dispersion Model (LPDM) "FLEXPART". A consistent minimum between the two EC mass size modes was observed at approximately 400 nm for the measurement period. EC particles below this size are attributed to local emissions using chemical mixing state information and contribute 79% of the scaled ATOFMS EC particle mass, while particles above this size are attributed to continental transport events and contribute 21% of the EC particle mass. These results clearly demonstrate the potential benefit of monitoring size-resolved mass concentrations for the separation of local and continental EC emissions. Knowledge of the relative input of these emissions is essential for assessing the effectiveness of local abatement strategies.

The effects of agglomeration economies on the productivity of manufacturing local units in Ireland

The purpose of this study is to examine the effects of agglomeration economies on the productivity of manufacturing local units in Ireland. Four types of agglomeration economies are considered in this study. These are internal economies of scale, localization economies, related variety and urbanization economies. This study makes a number of contributions to the literature. Firstly, this is the first study to conduct an investigation of the effects of agglomeration economies on the productivity of manufacturing local units operating in Ireland. Secondly, this study distinguishes between indigenous and foreign-owned local units which is important given the dual nature of the Irish economy (Krugman, 1997). Thirdly, in addition to considering the effects of agglomeration economies, this study examines the impact of spurious agglomeration on the productivity of foreign-owned local units. Using data from the Census of Industrial Local Units and a series of IV GMM estimators to control for endogeneity, the results of the analysis conducted in Chapter 6 reveal that there are differences in the effects of agglomeration economies on the productivity of indigenous and foreign-owned local units. In Chapter 7 the Census of Industrial Local Units is supplemented by additional data sources and more in-depth measures are generated to capture the features of each of the external agglomeration economies considered in this analysis. There is some evidence to suggest that the availability of local inputs has a negative and significant impact on productivity. The NACE based measures of related variety reveal that the availability of local inputs and knowledge spillovers for related sectors have a negative and significant impact on productivity. There is clear evidence to suggest that urbanization economies are important for increasing the productivity of indigenous local units. The findings reveal that a 1% increase in population density in the NUTS 3 region leads to an increase in the productivity of indigenous local units of approximately 0.07% to 0.08%. The results also reveal that there is a significant difference in the effects of agglomeration economies on the productivity of low-tech and medium/high-tech indigenous local units. The more in-depth measures of agglomeration economies used in Chapter 7 are also used in Chapter 8. A series of IV GMM regressions are estimated in order to identify the impact of agglomeration economies and spurious agglomeration on the productivity of foreign-owned local units operating in Ireland. There is some evidence found to suggest that the availability of a pool of skilled labour has a positive and significant on productivity of foreign-owned local units. There is also evidence to suggest that localization knowledge spillovers have a negative impact on the productivity of foreign-owned local units. There is strong evidence to suggest that the availability of local inputs has a negative impact on the productivity. The negative impact is not confined to the NACE 4-digit sector but also extends into related sectors as determined by Porter’s (2003) cluster classification. The cluster based skills measure of related variety has a positive and significant impact on the productivity of foreign-owned local units. Similar to Chapter 7, there is clear evidence to suggest that urbanization economies are important for increasing the productivity of foreign-owned local units. Both the summary measure and each of the more in-depth measures of agglomeration economies have a positive and significant impact on productivity. Spurious agglomeration has a positive and significant impact on the productivity of foreign-owned local units. The results indicate that the more foreign-owned local units of the same nationality in the country the greater the levels of productivity for the local unit. From a policy perspective, urbanization economies are clearly important for increasing the productivity of both indigenous and foreign-owned local units. Furthermore, the availability of a pool of skilled labour appears to be important for increasing the productivity of foreign-owned local units. Another policy implication that arises from these results relates to the differences observed between indigenous local units and foreign-owned local units and also between low-tech and medium/high-tech indigenous local units. These findings indicate that ‘one-size-fits-all’ type policies are not appropriate for increasing the productivity of local units operating in Ireland. Policies should be tailored to the needs of either indigenous or foreign-owned local units and also to specific sectors. This positive finding for own country spurious agglomeration is important from a policy perspective and is one that IDA Ireland should take on board.

Territorial administrative reorganization as a strategy for optimizing the structure of local government

Through the tough economic and social situation and the lack of values that has been experienced in recent years, local governments especially in Greece, Portugal, Italy and Spain have been forced to strongly consider the structure and size of their public sector. Despite some initiative to reduce the number of municipalities and provinces, little substantive progress has been made in improving the management of the local public Administration during this crisis. In this study a territorial administrative reorganization is proposed as a strategy to optimize the structure of local government, analyzing the Spanish situation in general, and an autonomous community in particular.

The influence of simulated exploitation onPatella vulgatapopulations: protandric sex change is size-dependent

Grazing mollusks are used as a food resource worldwide, and limpets are harvested commercially for both local consumption and export in several countries. This study describes a field experiment to assess the effects of simulated human exploitation of limpets Patella vulgata on their population ecology in terms of protandry (age-related sex change from male to female), growth, recruitment, migration, and density regulation. Limpet populations at two locations in southwest England were artificially exploited by systematic removal of the largest individuals for 18 months in plots assigned to three treatments at each site: no (control), low, and high exploitation. The shell size at sex change (L50: the size at which there is a 50:50 sex ratio) decreased in response to the exploitation treatments, as did the mean shell size of sexual stages. Size-dependent sex change was indicated by L50 occurring at smaller sizes in treatments than controls, suggesting an earlier switch to females. Mean shell size of P. vulgata neuters changed little under different levels of exploitation, while males and females both decreased markedly in size with exploitation. No differences were detected in the relative abundances of sexual stages, indicating some compensation for the removal of the bigger individuals via recruitment and sex change as no migratory patterns were detected between treatments. At the end of the experiment, 0–15 mm recruits were more abundant at one of the locations but no differences were detected between treatments. We conclude that sex change in P. vulgata can be induced at smaller sizes by reductions in density of the largest individuals reducing interage class competition. Knowledge of sex-change adaptation in exploited limpet populations should underpin strategies to counteract population decline and improve rocky shore conservation and resource management.

The influence of simulated exploitation onPatella vulgatapopulations: protandric sex change is size-dependent

Grazing mollusks are used as a food resource worldwide, and limpets are harvested commercially for both local consumption and export in several countries. This study describes a field experiment to assess the effects of simulated human exploitation of limpets Patella vulgata on their population ecology in terms of protandry (age-related sex change from male to female), growth, recruitment, migration, and density regulation. Limpet populations at two locations in southwest England were artificially exploited by systematic removal of the largest individuals for 18 months in plots assigned to three treatments at each site: no (control), low, and high exploitation. The shell size at sex change (L50: the size at which there is a 50:50 sex ratio) decreased in response to the exploitation treatments, as did the mean shell size of sexual stages. Size-dependent sex change was indicated by L50 occurring at smaller sizes in treatments than controls, suggesting an earlier switch to females. Mean shell size of P. vulgata neuters changed little under different levels of exploitation, while males and females both decreased markedly in size with exploitation. No differences were detected in the relative abundances of sexual stages, indicating some compensation for the removal of the bigger individuals via recruitment and sex change as no migratory patterns were detected between treatments. At the end of the experiment, 0–15 mm recruits were more abundant at one of the locations but no differences were detected between treatments. We conclude that sex change in P. vulgata can be induced at smaller sizes by reductions in density of the largest individuals reducing interage class competition. Knowledge of sex-change adaptation in exploited limpet populations should underpin strategies to counteract population decline and improve rocky shore conservation and resource management.

Importance of size-selective particle measuring for assessing occupational exposures: a case study “from field to fork”

Sampling the total air concentration of particulate matter (PM) only provides a basic estimate of exposure that normally not allows correlating with the observed health effects. Therefore is of great importance to recognize the particles size distribution and, particularly, the exposure to fine particles (≤ 2.5 μm). This particles dimension corresponds to the respirable fraction, the one that can implicate local and systemic effects due to particle deposition and clearance from the lungs and transport within the organism. This study intended to describe occupational exposure to PM2.5 in three units related with swine production and consumption, namely: feed production, swine production and swine slaughterhouse. A size-selective particle measuring in five to six workplaces of each unit was performed. Measurements of PM were done using a portable direct-reading hand-held equipment (Lighthouse, model 3016 IAQ). Data showed slaughterhouse unit with higher values, with values ranging from 0.030 to 0.142 mg/m3 (0.073 + 0.043), being the cutting room the workplace with higher values. In feed production unit, values were between 0.026 and 0.033 mg/m3 (0.028 + 0.003) with the warehouse of pharmacy products as the workplace with higher values. Finally, in swine unit values ranged from 0.006 to 0.048 mg/m3 (0.023 + 0.017) with the batteries area presenting the higher values. PM can be rich in fungi and bacteria and their metabolites, such as endotoxins and mycotoxins. Previous publications already showed high contamination in these occupational settings and particles can have an important role in exposure since can easily act as carrier of these agents. Data acquired allow not only a better prediction of particle penetration into respiratory regions of the respiratory tract, but also a better estimation of PM health effects. Moreover, data permit to identify the workplaces where investment should be made to prevent and reduce exposure.

Importance of size-selective particle sampling for assessing occupational exposures: results from three different occupational settings

Sampling the total air concentration of particulate matter (PM) only provides a basic estimate of exposure that normally not allows correlating with the observed health effects. Therefore is of extreme importance to know the particles size distribution and, in more detail, the exposure to fine particles (≤ 2.5 µm). This particles dimension corresponds to the respirable fraction. This particle fraction can result, besides local effects, in systemic effects due to particle deposition and clearance from the lungs and transport within the organism. This study intended to describe occupational exposure to PM2.5 in three different units located near Lisbon and related with occupational exposure to organic dust, namely: swine and poultry feed production and waste management.

Size-dependent electronic properties of metal nanoparticles.

105 p.

Stability and Local Toxicity Evaluation of a Liposomal Prilocaine Formulation

This study reports a physicochemical stability evaluation of a previously reported liposomal prilocaine (PLC(LUV)) formulation (Cereda el al. J. Pharm. Pharmaceut. Sci. 7:235, 2004) before and after steam sterilization as well as its local toxicity evaluation. Prilocaine (PLC) was encapsulated into extruded unilamellar liposomes (LUVs) composed by egg phosphatidylcholine:cholesterol:alfa-tocopherol (4:3:0.07, mole %). Laser light-scattering analysis (p > 0.05) and thiobarbituric acid reaction (p > 0.05) were used to evaluate the liposomes physical (size) and chemical (oxidation) stability, respectively. The prilocaine chemical stability was followed by (1)H-nuclear magnetic resonance. These tests detected no differences on the physicochemical stability of PLC or PLCLUV, sterilized or not, up to 30 days after preparation (p > 0.05). Finally, the paw edema test and histological analysis of rat oral mucosa were used to assess the possible inflammatory effects of PLC(LUV). PLC(LUV) did not evoke rat paw edema (p > 0.05), and no significant differences were found in histological analysis, when compared to the control groups (p > 0.05). The present work shows that PLC(LUV) is stable for a 30-day period and did not induce significant inflammatory effects both in the paw edema test and in histological analysis, giving supporting evidence for its safely and possible clinical use in dentistry.

Encapsulation of Local Anesthetic Bupivacaine in Biodegradable Poly(DL-lactide-co-glycolide) Nanospheres: Factorial Design, Characterization and Cytotoxicity Studies

Local anesthetic agents cause temporary blockade of nerve impulses productiong insensitivity to painful stimuli in the area supplied by that nerve. Bupivacaine (BVC) is an amide-type local anesthetic widely used in surgery and obstetrics for sustained peripheral and central nerve blockade. in this study, we prepared and characterized nanosphere formulations containing BVC. To achieve these goals, BVC loaded poly(DL-lactide-co-glycolide) (PLGA) nanospheres (NS) were prepared by nanopreciptation and characterized with regard to size distribution, drug loading and cytotoxicity assays. The 2(3-1) factorial experimental design was used to study the influence of three different independent variables on nanoparticle drug loading. BVC was assayed by HPLC, the particle size and zeta potential were determined by dynamic light scattering. BVC was determined using a combined ultrafiltration-centrifugation technique. The results of optimized formulations showed a narrow size distribution with a polydispersivity of 0.05%, an average diameter of 236.7 +/- 2.6 nm and the zeta potential -2.93 +/- 1,10 mV. In toxicity studies with fibroblast 3T3 cells, BVC loaded-PLGA-NS increased cell viability, in comparison with the effect produced by free BVC. In this way, BVC-loaded PLGA-NS decreased BVC toxicity. The development of BVC formulations in carriers such as nanospheres could offer the possibility of controlling drug delivery in biological systems, prolonging the anesthetic effect and reducing toxicity.