Structure and dynamics of the Shapley Supercluster - Velocity catalogue, general morphology and mass

We present results of our wide-field redshift survey of galaxies in a 285 square degree region of the Shapley Supercluster (SSC), based on a set of 10 529 velocity measurements (including 1201 new ones) on 8632 galaxies obtained from various telescopes and from the literature. Our data reveal that the main plane of the SSC (v approximate to 14 500 km s(-1)) extends further than previous estimates, filling the whole extent of our survey region of 12 degrees by 30 degrees on the sky (30 x 75 h(-1) Mpc). There is also a connecting structure associated with the slightly nearer Abell 3571 cluster complex (v approximate to 12 000 km s(-1)). These galaxies seem to link two previously identified sheets of galaxies and establish a connection with a third one at v = 15 000 km s(-1) near RA = 13(h). They also tend to fill the gap of galaxies between the foreground Hydra-Centaurus region and the more distant SSC. In the velocity range of the Shapley Supercluster (9000 km s(-1) < cz < 18 000 km s(-1)), we found redshift-space overdensities with b(j) < 17.5 of similar or equal to 5.4 over the 225 square degree central region and similar or equal to 3.8 in a 192 square degree region excluding rich clusters. Over the large region of our survey, we find that the intercluster galaxies make up 48 per cent of the observed galaxies in the SSC region and, accounting for the different completeness, may contribute nearly twice as much mass as the cluster galaxies. In this paper, we discuss the completeness of the velocity catalogue, the morphology of the supercluster, the global overdensity, and some properties of the individual galaxy clusters in the Supercluster.

EXPERIÊNCIAS AFETIVAS NO CONTEXTO ORGANIZACIONAL E SEU IMPACTO SOBRE O BEM-ESTAR NO TRABALHO

Em ambiente de elevada pressão, competição e necessidade de criação de diferenciais consistentes que venham contribuir com a longevidade das organizações, nota-se a busca e, às vezes, radicais transformações nos modelos de gestão de negócios e gestão do ser humano no meio empresarial. No campo central dos estudos atuais acerca do comportamento humano e de suas relações com as diversas instituições em que o homem se vê inserido, figuram os esforços voltados à compreensão do papel e valor da contribuição do ser humano ao ambiente de trabalho e fortalecimento das organizações. Crescentes se mostram a preocupação e o entendimento sobre os fatores que impactam o bem-estar geral, o bem-estar no trabalho, a saúde dos trabalhadores e as variáveis emocionais oriundas das relações interpessoais comuns a todo organismo social. A combinação de temas emergentes e ricos em significância como bem-estar no trabalho, satisfação e envolvimento com o trabalho, comprometimento organizacional afetivo, emoções, afetos e sentimentos, caracterizam-se como um vasto e instigante campo de pesquisa para uma adaptação mais ampla do ser humano ao ambiente organizacional. O presente estudo teve como objetivo submeter ao teste empírico as relações entre experiências afetivas no contexto organizacional e três dimensões de bem-estar no trabalho - satisfação no trabalho, envolvimento com o trabalho e comprometimento organizacional afetivo. A amostra foi composta por 253 profissionais de uma indústria metalúrgica de autopeças na grande São Paulo, sendo 213 do sexo masculino e 29 do sexo feminino, com maior freqüência na faixa etária compreendida entre 26 a 30 anos, distribuída entre solteiros e casados. Para a coleta de dados foi utilizado um questionário de auto-preenchimento com quatro escalas que avaliaram afetos positivos e negativos, satisfação no trabalho, envolvimento com o trabalho e comprometimento organizacional afetivo. A análise dos dados foi feita por meio do SPSS, versão 16.0 e diversos sub-programas permitiram realizar análises descritivas bem como calcular modelos de regressão linear para verificar o impacto de afetos positivos e negativos sobre bem-estar no trabalho. Os resultados deste estudo revelaram que o principal preditor das dimensões de bem-estar no trabalho foram os afetos positivos. Assim, parece ser adequado afirmar que bem-estar no trabalho seja um estado psicológico sustentado, em especial, pela vivência de emoções positivas no contexto organizacional. Sugere-se que a promoção da saúde e do bem-estar dentro das organizações sejam focos de estudos futuros, representando valiosa contribuição aos campos de conhecimento da psicologia da saúde e da psicologia organizacional, bem como ao conseqüente fortalecimento dos vínculos entre empresa e trabalhadores.(AU)

Cost-effective optical coherence tomography spectrometer based on a tilted fiber Bragg grating

A compact, fiber-based spectrometer for biomedical application utilizing a tilted fiber Bragg grating (TFBG) as integrated dispersive element is demonstrated. Based on a 45° UV-written PS750 TFBG a refractive spectrometer with 2.06 radiant/μm dispersion and a numerical aperture of 0.1 was set up and tested as integrated detector for an optical coherence tomography (OCT) system. Featuring a 23 mm long active region at the fiber the spectrum is projected via a cylindrical lens for vertical beam collimation and focused by an achromatic doublet onto the detector array. Covering 740 nm to 860 nm the spectrometer was optically connected to a broadband white light interferometer and a wide field scan head and electronically to an acquisition and control computer. Tomograms of ophthalmic and dermal samples obtained by the frequency domain OCT-system were obtained achieving 2.84 μm axial and 7.6 μm lateral resolution. © 2014 SPIE.

Photographic Plate Libraries at European Astronomical Observatories

ACM Computing Classification System (1998): J.2.

Potsdam Library of Astronomical Photographic Plates

ACM Computing Classification System (1998): J.2.

Digital Preservation and Web Access to the Konkoly Observatory Schmidt Telescope Plate Archive

ACM Computing Classification System (1998): J.2.

Software Tools for Digitization of Astronomical Photographic Plates

ACM Computing Classification System (1998): J.2.

AstroWeb – A Graphical Representation of an Astronomical WFPDB Database Using a Web-Based Open Source Geographical Information System

ACM Computing Classification System (1998): H.5.2, H.2.8, J.2, H.5.3.

Hough Transform Approach to Identification of Flare Stars in Multi-exposure Plate Images

ACM Computing Classification System (1998): I.2.8 , I.2.10, I.5.1, J.2.

Fourth-root summation of contrast over area:no end in sight when spatially inhomogeneous sensitivity is compensated by a witch's hat

Measurements of area summation for luminance-modulated stimuli are typically confounded by variations in sensitivity across the retina. Recently we conducted a detailed analysis of sensitivity across the visual field (Baldwin et al, 2012) and found it to be well-described by a bilinear “witch’s hat” function: sensitivity declines rapidly over the first 8 cycles or so, more gently thereafter. Here we multiplied luminance-modulated stimuli (4 c/deg gratings and “Swiss cheeses”) by the inverse of the witch’s hat function to compensate for the inhomogeneity. This revealed summation functions that were straight lines (on double log axes) with a slope of -1/4 extending to ≥33 cycles, demonstrating fourth-root summation of contrast over a wider area than has previously been reported for the central retina. Fourth-root summation is typically attributed to probability summation, but recent studies have rejected that interpretation in favour of a noisy energy model that performs local square-law transduction of the signal, adds noise at each location of the target and then sums over signal area. Modelling shows our results to be consistent with a wide field application of such a contrast integrator. We reject a probability summation model, a quadratic model and a matched template model of our results under the assumptions of signal detection theory. We also reject the high threshold theory of contrast detection under the assumption of probability summation over area.

Perception of global image contrast is predicted by the same spatial integration model of gain control as detection and discrimination

How are the image statistics of global image contrast computed? We answered this by using a contrast-matching task for checkerboard configurations of ‘battenberg’ micro-patterns where the contrasts and spatial spreads of interdigitated pairs of micro-patterns were adjusted independently. Test stimuli were 20 × 20 arrays with various sized cluster widths, matched to standard patterns of uniform contrast. When one of the test patterns contained a pattern with much higher contrast than the other, that determined global pattern contrast, as in a max() operation. Crucially, however, the full matching functions had a curious intermediate region where low contrast additions for one pattern to intermediate contrasts of the other caused a paradoxical reduction in perceived global contrast. None of the following models predicted this: RMS, energy, linear sum, max, Legge and Foley. However, a gain control model incorporating wide-field integration and suppression of nonlinear contrast responses predicted the results with no free parameters. This model was derived from experiments on summation of contrast at threshold, and masking and summation effects in dipper functions. Those experiments were also inconsistent with the failed models above. Thus, we conclude that our contrast gain control model (Meese & Summers, 2007) describes a fundamental operation in human contrast vision.

State detection of bond wires in IGBT modules using eddy current pulsed thermography

Insulated gate bipolar transistor (IGBT) modules are important safety critical components in electrical power systems. Bond wire lift-off, a plastic deformation between wire bond and adjacent layers of a device caused by repeated power/thermal cycles, is the most common failure mechanism in IGBT modules. For the early detection and characterization of such failures, it is important to constantly detect or monitor the health state of IGBT modules, and the state of bond wires in particular. This paper introduces eddy current pulsed thermography (ECPT), a nondestructive evaluation technique, for the state detection and characterization of bond wire lift-off in IGBT modules. After the introduction of the experimental ECPT system, numerical simulation work is reported. The presented simulations are based on the 3-D electromagnetic-thermal coupling finite-element method and analyze transient temperature distribution within the bond wires. This paper illustrates the thermal patterns of bond wires using inductive heating with different wire statuses (lifted-off or well bonded) under two excitation conditions: nonuniform and uniform magnetic field excitations. Experimental results show that uniform excitation of healthy bonding wires, using a Helmholtz coil, provides the same eddy currents on each, while different eddy currents are seen on faulty wires. Both experimental and numerical results show that ECPT can be used for the detection and characterization of bond wires in power semiconductors through the analysis of the transient heating patterns of the wires. The main impact of this paper is that it is the first time electromagnetic induction thermography, so-called ECPT, has been employed on power/electronic devices. Because of its capability of contactless inspection of multiple wires in a single pass, and as such it opens a wide field of investigation in power/electronic devices for failure detection, performance characterization, and health monitoring.

Sistema de conversão de energia eólica baseado no gerador de indução duplamente alimentado: análise e contribuição ao controle da máquina

The humanity reached a time of unprecedented technological development. Science has achieved and continues to achieve technologies that allowed increasingly to understand the universe and the laws which govern it, and also try to coexist without destroying the planet we live on. One of the main challenges of the XXI century is to seek and increase new sources of clean energy, renewable and able to sustain our growth and lifestyle. It is the duty of every researcher engage and contribute in this race of energy. In this context, wind power presents itself as one of the great promises for the future of electricity generation . Despite being a bit older than other sources of renewable energy, wind power still presents a wide field for improvement. The development of new techniques for control of the generator along with the development of research laboratories specializing in wind generation are one of the key points to improve the performance, efficiency and reliability of the system. Appropriate control of back-to-back converter scheme allows wind turbines based on the doubly-fed induction generator to operate in the variable-speed mode, whose benefits include maximum power extraction, reactive power injection and mechanical stress reduction. The generator-side converter provides control of active and reactive power injected into the grid, whereas the grid-side converter provides control of the DC link voltage and bi-directional power flow. The conventional control structure uses PI controllers with feed-forward compensation of cross-coupling dq terms. This control technique is sensitive to model uncertainties and the compensation of dynamic dq terms results on a competing control strategy. Therefore, to overcome these problems, it is proposed in this thesis a robust internal model based state-feedback control structure in order to eliminate the cross-coupling terms and thereby improve the generator drive as well as its dynamic behavior during sudden changes in wind speed. It is compared the conventional control approach with the proposed control technique for DFIG wind turbine control under both steady and gust wind conditions. Moreover, it is also proposed in this thesis an wind turbine emulator, which was developed to recreate in laboratory a realistic condition and to submit the generator to several wind speed conditions.

Temporal Coding of Volumetric Imagery

'Image volumes' refer to realizations of images in other dimensions such as time, spectrum, and focus. Recent advances in scientific, medical, and consumer applications demand improvements in image volume capture. Though image volume acquisition continues to advance, it maintains the same sampling mechanisms that have been used for decades; every voxel must be scanned and is presumed independent of its neighbors. Under these conditions, improving performance comes at the cost of increased system complexity, data rates, and power consumption.

This dissertation explores systems and methods capable of efficiently improving sensitivity and performance for image volume cameras, and specifically proposes several sampling strategies that utilize temporal coding to improve imaging system performance and enhance our awareness for a variety of dynamic applications.

Video cameras and camcorders sample the video volume (x,y,t) at fixed intervals to gain understanding of the volume's temporal evolution. Conventionally, one must reduce the spatial resolution to increase the framerate of such cameras. Using temporal coding via physical translation of an optical element known as a coded aperture, the compressive temporal imaging (CACTI) camera emonstrates a method which which to embed the temporal dimension of the video volume into spatial (x,y) measurements, thereby greatly improving temporal resolution with minimal loss of spatial resolution. This technique, which is among a family of compressive sampling strategies developed at Duke University, temporally codes the exposure readout functions at the pixel level.

Since video cameras nominally integrate the remaining image volume dimensions (e.g. spectrum and focus) at capture time, spectral (x,y,t,\lambda) and focal (x,y,t,z) image volumes are traditionally captured via sequential changes to the spectral and focal state of the system, respectively. The CACTI camera's ability to embed video volumes into images leads to exploration of other information within that video; namely, focal and spectral information. The next part of the thesis demonstrates derivative works of CACTI: compressive extended depth of field and compressive spectral-temporal imaging. These works successfully show the technique's extension of temporal coding to improve sensing performance in these other dimensions.

Geometrical optics-related tradeoffs, such as the classic challenges of wide-field-of-view and high resolution photography, have motivated the development of mulitscale camera arrays. The advent of such designs less than a decade ago heralds a new era of research- and engineering-related challenges. One significant challenge is that of managing the focal volume (x,y,z) over wide fields of view and resolutions. The fourth chapter shows advances on focus and image quality assessment for a class of multiscale gigapixel cameras developed at Duke.

Along the same line of work, we have explored methods for dynamic and adaptive addressing of focus via point spread function engineering. We demonstrate another form of temporal coding in the form of physical translation of the image plane from its nominal focal position. We demonstrate this technique's capability to generate arbitrary point spread functions.

Degradation rates and productivity signals of organic-walled dinoflagellate cyst species in surface sediment samples

To understand the role of the ocean within the global carbon cycle, detailed information is required on key-processes within the marine carbon cycle; bio-production in the upper ocean, export of the produced material to the deep ocean and the storage of carbon in oceanic sediments. Quantification of these processes requires the separation of signals of net primary production and the rate of organic matter decay as reflected in fossil sediments. This study examines the large differences in degradation rates of organic-walled dinoflagellate cyst species to separate these degradation and productivity signals. For this, accumulation rates of cyst species known to be resistant (R-cysts) or sensitive (S-cysts) to aerobic degradation of 62 sites are compared to mean annual chlorophyll-a, sea-surface temperature, sea-surface salinity, nitrate and phosphate concentrations of the upper waters and deep-water oxygen concentrations. Furthermore, the degradation of sensitive cysts, as expressed by the degradation constant k and reaction time t, has been related to bottom water [O2]. The studied sediments were taken from the Arabian Sea, north-western African Margin (North Atlantic), western-equatorial Atlantic Ocean/Caraibic, south-western African margin (South Atlantic) and Southern Ocean (Atlantic sector). Significant relationships are observed between (a) accumulation rates of R-cysts and upper water chlorophyll-a concentrations, (b) accumulation rates of S-cysts and bottom water [O2] and (c) degradation rates of S-cysts (kt) and bottom water [O2]. Relationships that are extremely weak or are clearly insignificant on all confidence intervals are between (1) S-cyst accumulation rates and chlorophyll-a concentrations, sea-surface temperature (SST), sea-surface salinity (SSS), phosphate concentrations (P) and nitrate concentrations (N), (2) between R-cyst accumulation rates and bottom water [O2], SST, SSS, P and N, and between (3) kt and water depth. Co-variance is present between the parameters N and P, N, P and chlorophyll-a, oxygen and water depth. Correcting for this co-variance does not influence the significance of the relationship given above. The possible applicability of dinoflagellate cyst degradation to estimate past net primary production and deep ocean ventilation is discussed.