Enzyme loading dependence of cellulose hydrolysis of sugarcane bagasse

The enzymatic hydrolysis of steam-pretreated sugarcane bagasse, either delignified or non-delignified, was studied as a function of enzyme loading. Hydrolysis experiments were carried out using five enzyme loadings (2.5 to 20 FPU/g cellulose) and the concentration of solids was 2% for both materials. Alkaline delignification improved cellulose hydrolysis by increasing surface area. For both materials, glucose concentrations increased with enzyme loading. On the other hand, enzyme loadings higher than 15 FPU/g did not result in any increase in the initial rate, since the excess of enzyme adsorbed onto the substrate restricted the diffusion process through the structure.

METHANE DRY REFORMING OVER Ni SUPPORTED ON PINE SAWDUST ACTIVATED CARBON: EFFECTS OF SUPPORT SURFACE PROPERTIES AND METAL LOADING

The influence of metal loading and support surface functional groups (SFG) on methane dry reforming (MDR) over Ni catalysts supported on pine-sawdust derived activated carbon were studied. Using pine sawdust as the catalyst support precursor, the smallest variety and lowest concentration of SFG led to best Ni dispersion and highest catalytic activity, which increased with Ni loading up to 3 Ni atoms nm-2. At higher Ni loading, the formation of large metal aggregates was observed, consistent with a lower "apparen" surface area and a decrease in catalytic activity. The H2/CO ratio rose with increasing reaction temperature, indicating that increasingly important side reactions were taking place in addition to MDR.

Promoting Programming Learning. Engagement, Automatic Assessment with Immediate Feedback in Visualizations

The skill of programming is a key asset for every computer science student. Many studies have shown that this is a hard skill to learn and the outcomes of programming courses have often been substandard. Thus, a range of methods and tools have been developed to assist students’ learning processes. One of the biggest fields in computer science education is the use of visualizations as a learning aid and many visualization based tools have been developed to aid the learning process during last few decades. Studies conducted in this thesis focus on two different visualizationbased tools TRAKLA2 and ViLLE. This thesis includes results from multiple empirical studies about what kind of effects the introduction and usage of these tools have on students’ opinions and performance, and what kind of implications there are from a teacher’s point of view. The results from studies in this thesis show that students preferred to do web-based exercises, and felt that those exercises contributed to their learning. The usage of the tool motivated students to work harder during their course, which was shown in overall course performance and drop-out statistics. We have also shown that visualization-based tools can be used to enhance the learning process, and one of the key factors is the higher and active level of engagement (see. Engagement Taxonomy by Naps et al., 2002). The automatic grading accompanied with immediate feedback helps students to overcome obstacles during the learning process, and to grasp the key element in the learning task. These kinds of tools can help us to cope with the fact that many programming courses are overcrowded with limited teaching resources. These tools allows us to tackle this problem by utilizing automatic assessment in exercises that are most suitable to be done in the web (like tracing and simulation) since its supports students’ independent learning regardless of time and place. In summary, we can use our course’s resources more efficiently to increase the quality of the learning experience of the students and the teaching experience of the teacher, and even increase performance of the students. There are also methodological results from this thesis which contribute to developing insight into the conduct of empirical evaluations of new tools or techniques. When we evaluate a new tool, especially one accompanied with visualization, we need to give a proper introduction to it and to the graphical notation used by tool. The standard procedure should also include capturing the screen with audio to confirm that the participants of the experiment are doing what they are supposed to do. By taken such measures in the study of the learning impact of visualization support for learning, we can avoid drawing false conclusion from our experiments. As computer science educators, we face two important challenges. Firstly, we need to start to deliver the message in our own institution and all over the world about the new – scientifically proven – innovations in teaching like TRAKLA2 and ViLLE. Secondly, we have the relevant experience of conducting teaching related experiment, and thus we can support our colleagues to learn essential know-how of the research based improvement of their teaching. This change can transform academic teaching into publications and by utilizing this approach we can significantly increase the adoption of the new tools and techniques, and overall increase the knowledge of best-practices. In future, we need to combine our forces and tackle these universal and common problems together by creating multi-national and multiinstitutional research projects. We need to create a community and a platform in which we can share these best practices and at the same time conduct multi-national research projects easily.

COMPARISON OF PROCEDURES FOR IMMEDIATE CHEMICAL ANALYSIS OF CHARCOAL

ABSTRACT The climate change, the quest for sustainability and the strong environmental pressures for alternatives to traditional fossil fuels have increased the interest in the search and use of renewable energy sources. Among them stands out the biomass of charcoal coming from renewable forests, widely used as a thermal reductant in the steel industry in the detriment of the use of mineral coal coke. This study aimed to compare different operating procedures of immediate chemical analysis of charcoal. Seven essays to immediate chemical analysis were compared, spread between procedures performed by Brazilian companies and laboratories, the test described by NBR 8112 and one realized with a thermogravimetric analyzer (TGA) using the parameters of the NBR 8112. There were significant differences in the volatiles matter content and consequently in the fixed carbon contents found. The differences between the procedures and the NBR 8112 were caused by an excess burning time, a mass sample above or below the standard or inappropriate container used for burning. It observed that the TGA appraisal of the volatiles content must be carried out with a burning time equal to 2 minutes to obtain results similar to those of the NBR 8112 norm. Moreover, the ash content values were statistically identical and the particles size did not influence the differences between means.

Swine effluent treatment using anaerobic digestion at different loading rates

The industrial swine production is characterized by generation of significant effluent amounts that require treatment. The most adopted practices by Brazilian swine farmers have been wastewater storage in lagoons and its subsequent use as a biofertilizer. Nutrient accumulation in soil and water creates the need for an effective management of these residues. The anaerobic digestion process is an important alternative and low-cost treatment for organic matter reduction. However, its efficiency is limited by the digester capacity of solid degradation, especially at low hydraulic retention times. Thus, the present study aimed to verify the behavior of an upflow anaerobic digester by increasing the organic loading rate. This was accomplished in three stages using, as a parameter, volatile solids at 0.5; 1.0 and 1.5 kgVS m-3 d-1, respectively. This digester model proved to be quite robust and effective in swine manure treatment, achieving high efficiency of volatile solid removal at all stages of the study (stage 1: 61.38%; stage 2: 55.18%; and stage 3: 43.18%). Biogas production was directly related to the increasing organic load, reaching 0.14, 0.85, and 0.86 Nm³ kgVS-1add., respectively, with no significant difference (p<0.05) of biogas methane concentration among the studied stages (73.7, 75.0, and 77.9%).

Mechanical damage during harvest and loading affect orange postharvest quality

Brazil is the world’s largest orange producer; however, part of this production is lost during postharvest. This loss can be minimized by controlling incidence of physical damage throughout the harvest and loading operations. Impacts can negatively modify quantitative and qualitative fruits aspects. The main goal of this study was to measure the impact magnitude in two types of harvest (manual and detachment) and during all steps from picking into bags until loading for transport to the processing industry and additionally evaluating, in laboratory, the physico-chemical quality of the fruit subjected to various impacts, similar to those found in the field. In order to evaluate the impact magnitude, an instrumented sphere was used (760 mm, Techmark, Inc, USA). The following physico-chemical parameters were evaluated during 6-days of storage: weight loss, soluble solids contents, titratable acidity, ascorbic acid content, pH, firmness and peel color. The greatest impacts were observed during harvest, during the detachment practice, and when loading and unloading from bulk storage, with average acceleration values between 249.5 and 531.52G. The impact incidence in oranges were responsible for reducing the soluble solids, titratable acidity, ascorbic acid and weight by to 5.5%; 8.7%; 4.6% and 0.5%, respectively, compared to the control. Impacts during harvest and the various pre-industry manipulation steps must be controlled as they interfere in postharvest quality and physiology of ‘Valência’ oranges.

Immediate Decision-Making and Information Needs in Intensive Care Coordination

The aim of this study was to develop a theoretical model for information integration to support the deci¬sion making of intensive care charge nurses, and physicians in charge – that is, ICU shift leaders. The study focused on the ad hoc decision-making and immediate information needs of shift leaders during the management of an intensive care unit’s (ICU) daily activities. The term ‘ad hoc decision-making’ was defined as critical judgements that are needed for a specific purpose at a precise moment with the goal of ensuring instant and adequate patient care and a fluent flow of ICU activities. Data collection and research analysis methods were tested in the identification of ICU shift leaders’ ad hoc decision-making. Decision-making of ICU charge nurses (n = 12) and physicians in charge (n = 8) was observed using a think-aloud technique in two university-affiliated Finnish ICUs for adults. The ad hoc decisions of ICU shift leaders were identified using an application of protocol analysis. In the next phase, a structured online question¬naire was developed to evaluate the immediate information needs of ICU shift leaders. A national survey was conducted in all Finnish, university-affiliated hospital ICUs for adults (n = 17). The questionnaire was sent to all charge nurses (n = 515) and physicians in charge (n = 223). Altogether, 257 charge nurses (50%) and 96 physicians in charge (43%) responded to the survey. The survey was also tested internationally in 16 Greek ICUs. From Greece, 50 charge nurses out of 240 (21%) responded to the survey. A think-aloud technique and protocol analysis were found to be applicable for the identification of the ad hoc decision-making of ICU shift leaders. During one day shift leaders made over 200 ad hoc decisions. Ad hoc decisions were made horizontally, related to the whole intensive care process, and vertically, concerning single intensive care incidents. Most of the ICU shift leaders’ ad hoc decisions were related to human resources and know-how, patient information and vital signs, and special treatments. Commonly, this ad hoc decision-making involved several multiprofessional decisions that constituted a bundle of immediate decisions and various information needs. Some of these immediate information needs were shared between the charge nurses and the physicians in charge. The majority of which concerned patient admission, the organisation and management of work, and staff allocation. In general, the information needs of charge nurses were more varied than those of physicians. It was found that many ad hoc deci-sions made by the physicians in charge produced several information needs for ICU charge nurses. This meant that before the task at hand was completed, various kinds of information was sought by the charge nurses to support the decision-making process. Most of the immediate information needs of charge nurses were related to the organisation and management of work and human resources, whereas the information needs of the physicians in charge mainly concerned direct patient care. Thus, information needs differ between professionals even if the goal of decision-making is the same. The results of the international survey confirmed these study results for charge nurses. Both in Finland and in Greece the information needs of charge nurses focused on the organisation and management of work and human resources. Many of the most crucial information needs of Finnish and Greek ICU charge nurses were common. In conclusion, it was found that ICU shift leaders make hundreds of ad hoc decisions during the course of a day related to the allocation of resources and organisation of patient care. The ad hoc decision-making of ICU shift leaders is a complex multi-professional process, which requires a lot of immediate information. Real-time support for information related to patient admission, the organisation and man¬agement of work, and allocation of staff resources is especially needed. The preliminary information integration model can be applied when real-time enterprise resource planning systems are developed for intensive care daily management

Modelling of mechanical properties of CRFC composites under flexure loading

Carbon Fibre Reinforced Carbon (CFRC) Composites are increasing their applications due to their high strength and Young’s Modulus at high temperatures in inert atmosphere. Although much work has been done on processing and structure and properties relationship, few studies have addressed the modelling of mechanical properties. This work is divided in two parts. In the first part, a modelling of mechanical properties was carried out for two bi-directional composites using a model based on the Bernoulli-Euler theory for symmetric laminated beams. In the second part, acoustic emission (AE) was used as an auxiliary technique for monitoring the failure process of the composites. Differences in fracture behaviour are reflected in patterns of AE.

Instability of a square sheet under symmetric biaxial loading

An early experiment found that a square rubber sheet under symmetric biaxial loading may not remain square. This curious result has been one of the most instructive examples in finite elasticity. Here thermodynamic considerations are used to analyze this instability.

Relative contribution of expectancy and immediate arousal to the facilitatory effect of an auditory accessory stimulus

An auditory stimulus speeds up a digital response to a subsequent visual stimulus. This facilitatory effect has been related to the expectancy and the immediate arousal that would be caused by the accessory stimulus. The present study examined the relative contribution of these two influences. In a first and a third experiment a simple reaction time task was used. In a second and fourth experiment a go/no-go reaction time task was used. In each of these experiments, the accessory stimulus preceded the target stimulus by 200 ms for one group of male and female volunteers (G Fix). For another group of similar volunteers (G Var) the accessory stimulus preceded the target stimulus by 200 ms in 25% of the trials, by 1000 ms in 25% of the trials and was not followed by the target stimulus in 50% of the trials (Experiments 1a and 1b) or preceded the target stimulus by 200 ms in 6% of the trials and by 1000 ms in 94% of the trials (Experiments 2a and 2b). There was a facilitatory effect of the accessory stimulus for G Fix in the four experiments. There was also a facilitatory effect of the accessory stimulus at the 200-ms stimulus onset asynchrony for G Var in Experiments 1a and 1b but not in Experiments 2a and 2b. The facilitatory effects observed were larger in the go/no-go task than in the simple task. Taken together, these results suggest that expectancy is much more important than immediate arousal for the improvement of performance caused by an accessory stimulus.

Study on Customer Perceived Value of Container Loading Equipment

The goal of the thesis was to gain understanding of organizational buying behavior and its effect from the selling perspective and to generate base for verifying customer value propositions for Actiw Oy. The first objective was to discover the current buying decision criteria of current customers to understand the buying motives which had led to the investment initially. Second objective was to understand how the buying decision criteria and customer experiences can be turned into customer value propositions. Research was done with 16 customer interviews, which were focused on obtaining the information on the buying center and the value of the solution. Thesis goes through the main theories of OBB and the theory behind customer value management. Based on customer interviews, the currently used customer value propositions were tested and categorized into points-of-parities and points-ofdifferences. The interviews confirmed customer behavior in new task and modified rebuy situations and also gave confirmation to the internally done customer value propositions. Main finding of the study was, that as the value propositions are possible to present more specifically to each new case instead of using all benefits at the same time.

Immediate effects of submaximal effort on pulse wave velocity in patients with Marfan syndrome

Marfan syndrome (MS) is a dominant autosomal disease caused by mutations in chromosome 15, the locus controlling fibrillin 1 synthesis, and may exhibit skeletal, ocular, cardiovascular, and other manifestations. Pulse wave velocity (PWV) is used to measure arterial elasticity and stiffness and is related to the elastic properties of the vascular wall. Since the practice of exercise is limited in MS patients, it was of interest to analyze the acute effect of submaximal exercise on aortic distensibility using PWV and other hemodynamic variables in patients with MS with either mild or no aortic dilatation. PWV and physiological variables were evaluated before and after submaximal exercise in 33 patients with MS and 18 controls. PWV was 8.51 ± 0.58 at rest and 9.10 ± 0.63 m/s at the end of exercise (P = 0.002) in the group with MS and 8.07 ± 0.35 and 8.98 ± 0.56 m/s in the control group, respectively (P = 0.004). Comparative group analysis regarding PWV at rest and at the end of exercise revealed no statistically significant differences. The same was true for the group that used β-blockers and the one that did not. The final heart rate was 10% higher in the control group than in the MS group (P = 0.01). Final systolic arterial pressure was higher in the control group (P = 0.02). PWV in MS patients with mild or no aortic dilatation did not differ from the control group after submaximal effort.

Effect of loading type on the fatigue strength of symmetric and asymmetric welded joints made of ultra high strength steel

In this study, finite element analyses and experimental tests are carried out in order to investigate the effect of loading type and symmetry on the fatigue strength of three different non-load carrying welded joints. The current codes and recommendations do not give explicit instructions how to consider degree of bending in loading and the effect of symmetry in the fatigue assessment of welded joints. The fatigue assessment is done by using effective notch stress method and linear elastic fracture mechanics. Transverse attachment and cover plate joints are analyzed by using 2D plane strain element models in FEMAP/NxNastran and Franc2D software and longitudinal gusset case is analyzed by using solid element models in Abaqus and Abaqus/XFEM software. By means of the evaluated effective notch stress range and stress intensity factor range, the nominal fatigue strength is assessed. Experimental tests consist of the fatigue tests of transverse attachment joints with total amount of 12 specimens. In the tests, the effect of both loading type and symmetry on the fatigue strength is studied. Finite element analyses showed that the fatigue strength of asymmetric joint is higher in tensile loading and the fatigue strength of symmetric joint is higher in bending loading in terms of nominal and hot spot stress methods. Linear elastic fracture mechanics indicated that bending reduces stress intensity factors when the crack size is relatively large since the normal stress decreases at the crack tip due to the stress gradient. Under tensile loading, experimental tests corresponded with finite element analyzes. Still, the fatigue tested joints subjected to bending showed the bending increased the fatigue strength of non-load carrying welded joints and the fatigue test results did not fully agree with the fatigue assessment. According to the results, it can be concluded that in tensile loading, the symmetry of joint distinctly affects on the fatigue strength. The fatigue life assessment of bending loaded joints is challenging since it depends on whether the crack initiation or propagation is predominant.

The Falls of Niagara : being a complete guide to all the points of interest around and in the immediate neighbourhood of the great cataract with views taken from sketches by Washington Friend, and from photographs. --

Includes index.