Contribuições à estratégia de controle sem detecção de harmônicos aplicada a um filtro ativo de potência paralelo

The conventional control schemes applied to Shunt Active Power Filters (SAPF) are Harmonic extractor-based strategies (HEBSs) because their effectiveness depends on how quickly and accurately the harmonic components of the nonlinear loads are identified. The SAPF can be also implemented without the use of the load harmonic extractors. In this case, the harmonic compensating term is obtained from the system active power balance. These systems can be considered as balanced-energy-based schemes (BEBSs) and their performance depends on how fast the system reaches the equilibrium state. In this case, the phase currents of the power grid are indirectly regulated by double sequence controllers with two degrees of freedom, where the internal model principle is employed to avoid reference frame transformation. Additionally the DSC controller presents robustness when the SAPF is operating under unbalanced conditions. Furthermore, SAPF implemented without harmonic detection schemes compensate simultaneously harmonic distortion and reactive power of the load. Their compensation capabilities, however, are limited by the SAPF power converter rating. Such a restriction can be minimized if the level of the reactive power correction is managed. In this work an estimation scheme for determining the filter currents is introduced to manage the compensation of reactive power. Experimental results are shown for demonstrating the performance of the proposed SAPF system.

Um algoritmo paralelo eficiente de migração reversa no tempo (rtm) 3d com granularidade fina

The reverse time migration algorithm (RTM) has been widely used in the seismic industry to generate images of the underground and thus reduce the risk of oil and gas exploration. Its widespread use is due to its high quality in underground imaging. The RTM is also known for its high computational cost. Therefore, parallel computing techniques have been used in their implementations. In general, parallel approaches for RTM use a coarse granularity by distributing the processing of a subset of seismic shots among nodes of distributed systems. Parallel approaches with coarse granularity for RTM have been shown to be very efficient since the processing of each seismic shot can be performed independently. For this reason, RTM algorithm performance can be considerably improved by using a parallel approach with finer granularity for the processing assigned to each node. This work presents an efficient parallel algorithm for 3D reverse time migration with fine granularity using OpenMP. The propagation algorithm of 3D acoustic wave makes up much of the RTM. Different load balancing were analyzed in order to minimize possible losses parallel performance at this stage. The results served as a basis for the implementation of other phases RTM: backpropagation and imaging condition. The proposed algorithm was tested with synthetic data representing some of the possible underground structures. Metrics such as speedup and efficiency were used to analyze its parallel performance. The migrated sections show that the algorithm obtained satisfactory performance in identifying subsurface structures. As for the parallel performance, the analysis clearly demonstrate the scalability of the algorithm achieving a speedup of 22.46 for the propagation of the wave and 16.95 for the RTM, both with 24 threads.

Eficacia del aceite de oliva en la prevención de úlceras por presión en pacientes inmovilizados en atención primaria. Ensayo clínico aleatorizado, multicéntrico, paralelo, triple ciego, de no inferioridad

Las úlceras por presión representan un importante problema de salud pública y tienen un importante impacto económico en los sistemas de salud. La mayoría de los estudios para prevenir las úlceras por presión se han llevado a cabo en contextos hospitalarios, usando ácidos grasos hiperoxigenados (AGHO) y hasta la fecha, no se ha realizado ningún estudio específico con aceite de oliva virgen extra (AOVE) en el entorno domiciliario. Material y método Objetivo principal: evaluar si la utilización de AOVE no es inferior a los AGHO en la prevención de úlceras por presión (UPP) en pacientes inmovilizados en el entorno domiciliario. Diseño: Ensayo clínico aleatorizado multicéntrico, paralelo, a triple ciego, de no inferioridad. Ámbito: Población consultante de centros de salud andaluces. Muestra: 831 pacientes inmovilizados en riesgo de padecer UPP. Resultados El período de seguimiento fue de 16 semanas. En el análisis por protocolo, ninguna de las zonas evaluadas presentó diferencias de riesgo de incidencia de las úlceras por presión que superasen el valor delta establecido (10%). Sacro: AOVE 8 (2,55%) vs AGHO 8 (3,08%), RAR 0,53 (-2,2 a 3,26). Talón derecho: AOVE 4 (1,27%) vs AGHO 5 (1,92)%, RAR 0,65 (-1,43 a 2,73). Talón izquierdo: AOVE 3 (0,96%) vs AGHO 3 (1,15%), RAR 0.2 (-1,49 a 1,88). Trocánter Derecho: AOVE 0 (0%) vs AGHO 4 (1,54%), RAR 1,54 (0,04-3,03). Trocánter izquierdo: AOVE 1 (0,32%) vs AGHO 1 (0,38%), RAR 0.07 (-0,91 a 1,04). Discusión Este ensayo clínico pretendía evaluar si la prevención de las UPP usando una fórmula de AOVE no era inferior a la prevención de UPP con el uso AGHO, en el entorno domiciliario y con pacientes inmovilizados de alto riesgo. Los resultados han mostrado esta no inferioridad al no observarse diferencias que hayan superado el límite inferior del intervalo de confianza y convierte al aceite de oliva en un producto eficaz para la prevención de UPP en este tipo de pacientes. Se necesitan más estudios para investigar el mecanismo de acción del AOVE en la prevención de las UPP y relacionarlo con la etiopatogenia de éstas. Bibliografía 1. Gorecki C, Brown JM, Nelson EA, Briggs M, Schoonhoven L, Dealey C, et al. Impact of pressure ulcers on quality of life in older patients: a systematic review. J Am Geriatr Soc. 2009 Jul;57(7):1175–83. 2. Yamamoto Y, Hayashino Y, Higashi T, Matsui M, Yamazaki S, Takegami M, et al. Keeping vulnerable elderly patients free from pressure ulcer is associated with high caregiver burden in informal caregivers. J Eval Clin Pract. 2010 Jun;16(3):585–9. 3. Hanson D, Langemo DK, Anderson J, Thompson P, Hunter S. Friction and shear considerations in pressure ulcer development. Adv Skin Wound Care. 2010 Jan;23(1):21–4. 4. Soldevilla Agreda JJ, Torra i Bou J-E, Verdú Soriano J, López Casanova P. 3.er Estudio Nacional de Prevalencia de Úlceras por Presión en España, 2009: Epidemiología y variables definitorias de las lesiones y pacientes. Gerokomos. 2011 Jun;22(2):77–90. 5. Kottner J, Lahmann N, Dassen T. [Pressure ulcer prevalence: comparison between nursing homes and hospitals]. Pflege Z. 2010 Apr;63(4):228–31. 6. Wilborn D, Halfens R, Dassen T, Tannen A. [Pressure ulcer prevalence in German nursing homes and hospitals: what role does the National Nursing Expert Standard Prevention of Pressure Ulcer play?]. Gesundheitswesen Bundesverb Ärzte Öffentl Gesundheitsdienstes Ger. 2010 Apr;72(4):240–5. 7. Tubaishat A, Anthony D, Saleh M. Pressure ulcers in Jordan: a point prevalence study. J Tissue Viability. 2011 Feb;20(1):14–9. 8. James J, Evans JA, Young T, Clark M. Pressure ulcer prevalence across Welsh orthopaedic units and community hospitals: surveys based on the European Pressure Ulcer Advisory Panel minimum data set. Int Wound J. 2010 Jun;7(3):147–52. 9. Defloor T, Schoonhoven L, Katrien V, Weststrate J, Myny D. Reliability of the European Pressure Ulcer Advisory Panel classification system. J Adv Nurs. 2006 Apr;54(2):189–98

Algoritmo paralelo para determinação de autovalores de matrizes hermitianas

Dissertação (mestrado)–Universidade de Brasília, Universidade UnB de Planaltina, Programa de Pós-Graduação em Ciência de Materiais, 2015.

High-voltage modular power supply using parallel and series configurations of flyback converter for pulsed power applications

To cover wide range of pulsed power applications, this paper proposes a modularity concept to improve the performance and flexibility of the pulsed power supply. The proposed scheme utilizes the advantage of parallel and series configurations of flyback modules in obtaining high-voltage levels with fast rise time (dv/dt). Prototypes were implemented using 600-V insulated-gate bipolar transistor (IGBT) switches to generate up to 4-kV output pulses with 1-kHz repetition rate for experimentation. To assess the proposed modular approach for higher number of the modules, prototypes were implemented using 1700-V IGBTs switches, based on ten-series modules, and tested up to 20 kV. Conducted experimental results verified the effectiveness of the proposed method

A Novel VSI- and CSI-Fed Active-Reactive Induction Motor Drive with Sinusoidal Voltages and Currents

Till date load-commutated inverter (LCI)-fed synchronous motor drive configuration is popular in high power applications (>10 MW). The leading power factor operation of synchronous motor by excitation control offers this simple and rugged drive structure. On the contrary, LCI-fed induction motor drive is absent as it always draws lagging power factor current. Therefore, complicated commutation circuit is required to switch off thyristors for a current source inverter (CSI)-driven induction motor. It poses the major hindrance to scale up the power rating of CSI-fed induction motor drive. Anew power topology for LCI-fed induction motor drive for medium-voltage drive application is proposed. A new induction machine (active-reactive induction machine) with two sets of three-phase winding is introduced as a drive motor. The proposed power configuration ensures sinusoidal voltage and current at the motor terminals. The total drive power is shared among a thyristor-based LCI, an insulated gate bipolar transistor (IGBT)-based two-level voltage source inverter (VSI), and a three-level VSI. The benefits of SCRs and IGBTs are explored in the proposed drive. Experimental results from a prototype drive verify the basic concepts of the drive.

Gate Drive Card for High Power Three Phase PWM Converters

Gate driver is an integral part of every power converter, drives the power semiconductor devices and also provides protection for the switches against short-circuit events and over-voltages during shut down. Gate drive card for IGBTs and MOSFETs with basic features can be designed easily by making use of discrete electronic components. Gate driver ICs provides attractive features in a single package, which improves reliability and reduces effort of design engineers. Either case needs one or more isolated power supplies to drive each power semiconductor devices and provide isolation to the control circuitry from the power circuit. The primary emphasis is then to provide simplified and compact isolated power supplies to the gate drive card with the requisite isolation strength and which consumes less space, and for providing thermal protection to the power semiconductor modules for 3-� 3 wire or 4 wire inverters.

Experimental Investigation on Switching Characteristics of High-Current Insulated Gate Bipolar Transistors at Low Currents

Insulated gate bipolar transistors (IGBTs) are used in high-power voltage-source converters rated up to hundreds of kilowatts or even a few megawatts. Knowledge of device switching characteristics is required for reliable design and operation of the converters. Switching characteristics are studied widely at high current levels, and corresponding data are available in datasheets. But the devices in a converter also switch low currents close to the zero crossings of the line currents. Further, the switching behaviour under these conditions could significantly influence the output waveform quality including zero crossover distortion. Hence, the switching characteristics of high-current IGBTs (300-A and 75-A IGBT modules) at low load current magnitudes are investigated experimentally in this paper. The collector current, gate-emitter voltage and collector-emitter voltage are measured at various low values of current (less than 10% of the device rated current). A specially designed in-house constructed coaxial current transformer (CCT) is used for device current measurement without increasing the loop inductance in the power circuit. Experimental results show that the device voltage rise time increases significantly during turn-off transitions at low currents.

An Advanced Gate Driver for Insulated Gate Bipolar Transistors to Eliminate Dead-time Induced Distortions in Inverter Output

Dead-time is introduced between the gating signals to the top and bottom switches in a voltage source inverter (VSI) leg, to prevent shoot through fault due to the finite turn-off times of IGBTs. The dead-time results in a delay when the incoming device is an IGBT, resulting in error voltage pulses in the inverter output voltage. This paper presents the design, fabrication and testing of an advanced gate driver, which eliminates dead-time and consequent output distortion. Here, the gating pulses are generated such that the incoming IGBT transition is not delayed and shoot-through is also prevented. The various logic units of the driver card and fault tolerance of the driver are verified through extensive tests on different topologies such as chopper, half-bridge and full-bridge inverter, and also at different conditions of load. Experimental results demonstrate the improvement in the load current waveform quality with the proposed circuit, on account of elimination of dead-time.

Experimental Investigation on Switching Characteristics of High-Current Insulated Gate Bipolar Transistors at Low Currents

Insulated gate bipolar transistors (IGBTs) are used in high-power voltage-source converters rated up to hundreds of kilowatts or even a few megawatts. Knowledge of device switching characteristics is required for reliable design and operation of the converters. Switching characteristics are studied widely at high current levels, and corresponding data are available in datasheets. But the devices in a converter also switch low currents close to the zero crossings of the line currents. Further, the switching behaviour under these conditions could significantly influence the output waveform quality including zero crossover distortion. Hence, the switching characteristics of high-current IGBTs (300-A and 75-A IGBT modules) at low load current magnitudes are investigated experimentally in this paper. The collector current, gate-emitter voltage and collector-emitter voltage are measured at various low values of current (less than 10% of the device rated current). A specially designed in-house constructed coaxial current transformer (CCT) is used for device current measurement without increasing the loop inductance in the power circuit. Experimental results show that the device voltage rise time increases significantly during turn-off transitions at low currents.

High temperature direct double side cooled inverter module for hybrid electric vehicle application

In this paper a novel approach to the design and fabrication of a high temperature inverter module for hybrid electrical vehicles is presented. Firstly, SiC power electronic devices are considered in place of the conventional Si devices. Use of SiC raises the maximum practical operating junction temperature to well over 200°C, giving much greater thermal headroom between the chips and the coolant. In the first fabrication, a SiC Schottky barrier diode (SBD) replaces the Si pin diode and is paired with a Si-IGBT. Secondly, double-sided cooling is employed, in which the semiconductor chips are sandwiched between two substrate tiles. The tiles provide electrical connections to the top and the bottom of the chips, thus replacing the conventional wire bonded interconnect. Each tile assembly supports two IGBTs and two SBDs in a half-bridge configuration. Both sides of the assembly are cooled directly using a high-performance liquid impingement system. Specific features of the design ensure that thermo-mechanical stresses are controlled so as to achieve long thermal cycling life. A prototype 10 kW inverter module is described incorporating three half-bridge sandwich assemblies, gate drives, dc-link capacitance and two heat-exchangers. This achieves a volumetric power density of 30W/cm3.

Biomasa y nutrientes de mantillo en diferentes sistemas de producción de café (Coffea arabica L.) en el municipio de Masatepe, departamento de Masaya, Nicaragua

En el municipio de Masatepe, Departamento de Masaya, Nicaragua, se determinó el aporte de la materia vegetal depositada sobre el suelo en diferentes sistemas de producción de café (Coffea arabica L.) y su contenido de N, P, K, Ca y Mg. Se evaluaron dos factores: A) Combinación de especies de árboles de sombra leguminosas y maderables (Inga laurina, Simarouba glauca, Enterolobium cyclocarpum, Tabebuia rosea) y una parcela a pleno sol; B) Niveles de insumo (Moderado y Alto convencional, Intensivo y Extensivo orgánico). El muestreo de campo se realizó en los meses de Mayo y Julio del año 2004, en el que se utilizó el método de marco cuadrado de 50 por 50 cm. Se seleccionaron seis puntos al azar en la parcela útil, en cada punto se ubicó el marco en la calle y otro paralelo en la hilera del cultivo. Se recolectó el material vegetal que estaba dentro del marco, separándose por componentes y especies encontrados (hojas y ramas); luego se procedió a pesar. Las muestras se secaron en un horno eléctrico a una temperatura de 65o C por un periodo de 72 horas para obtener el peso seco, y las mismas fueron enviadas al laboratorio de suelos en donde se determinaron los contenidos de nutrientes arriba mencionados. Los resultados obtenidos mostraron que el nivel de sombra IlSg (I. laurina-S. glauca) que es la combinación de una especie leguminosa con una maderable, presentaron el mayor aporte de materia vegetal al mantillo con 10,007kg ha-1, representando las mayores contenidos de nutrientes con 148.59 kg ha-1de N, 8.06 kg ha-1 de P, 73.29 kg ha-1 de K, 129.93 kg ha-1 deCa y 30.76 kg ha-1 de Mg, siendo también este nivel de sombra el que obtuvo un menor porcentaje de suelo desnudo (6.14 %) en comparación con los otros tratamientos. El nivel de insumo MO (intensivo orgánico) proporcionó la mayor cantidad de materia vegetal al mantillo con 8,509 kg ha-1 presentando los mayores contenidos de nutrientes de reserva con 131.43 kg ha-1 de N, 6.93 kg ha-1 de P, 63.77 kg ha-1K, 116.47 kg ha-1 Ca y 26.73 kg ha-1 de Mg. El nivel de insumo BO (extensivo orgánico) presentó el menor porcentaje de suelo desnudo (4.22 %).

La heráldica, el retrato y el fin de la Edad Media : un acercamiento antropológico a la iconografía

Resumen: Durante la Edad Media hizo su aparición la heráldica como forma de identificar ciertos aspectos de las personas, ya sea por su condición social o por su actividad específica. El uso de blasones y escudos de armas desde el siglo XI generó una importante cantidad de signos, colores y símbolos que edificaron todo un “patrón de lectura” del “rostro social” de la persona que portaba tal insignia, sin importar o no la veracidad de su rostro al confeccionarse un retrato pintado o esculpido. Paralelo a esto, la retratística que hubo durante todo el período medieval de personas reales, sagradas o ideales avanzó hacia un progresivo naturalismo que finalizó en el siglo XV con la reproducción del retratado tal cual era su fisonomía y abandonando el canon estereotipado que durante los siglos precedentes habían proliferado. Finalmente, con el creciente Humanismo, la aparición de la perspectiva y el progresivo abandono de la identificación de determinado personaje con sólo su escudo de armas, sirvió para que el retratado mirase a los ojos del observador y “dialogase”, develando aspectos espirituales antes ocultos. El objetivo de este trabajo es acercarse con una visión antropológica a la cuestión del retrato tardomedieval y renacentista en conjunción con los cambios operados en la heráldica y la iconografía, comprobando que la mirada tiene marcada intencionalidad, los rostros se frontalizan progresivamente y la heráldica pierde el espesor que tuvo en siglos precedentes