A novel procedure for establishing clinching parameters for high strength steel sheet

The building industry has a particular interest in using clinching as a joining method for frame constructions of light-frame housing. Normally many clinch joints are required in joining of frames.In order to maximise the strength of the complete assembly, each clinch joint must be as sound as possible. Experimental testing is the main means of optimising a particular clinch joint. This includes shear strength testing and visual observation of joint cross-sections. The manufacturers of clinching equipment normally perform such experimental trials. Finite element analysis can also be used to optimise the tool geometry and the process parameter, X, which represents the thickness of the base of the joint. However, such procedures require dedicated software, a skilled operator, and test specimens in order to verify the finite element model. In addition, when using current technology several hours' computing time may be necessary. The objective of the study was to develop a simple calculation procedure for rapidly establishing an optimum value for the parameter X for a given tool combination. It should be possible to use the procedure on a daily basis, without stringent demands on the skill of the operator or the equipment. It is also desirable that the procedure would significantly decrease thenumber of shear strength tests required for verification. The experimental workinvolved tests in order to obtain an understanding of the behaviour of the sheets during clinching. The most notable observation concerned the stage of the process in which the upper sheet was initially bent, after which the deformation mechanism changed to shearing and elongation. The amount of deformation was measured relative to the original location of the upper sheet, and characterised as the C-measure. By understanding in detail the behaviour of the upper sheet, it waspossible to estimate a bending line function for the surface of the upper sheet. A procedure was developed, which makes it possible to estimate the process parameter X for each tool combination with a fixed die. The procedure is based on equating the volume of material on the punch side with the volume of the die. Detailed information concerning the behaviour of material on the punch side is required, assuming that the volume of die does not change during the process. The procedure was applied to shear strength testing of a sample material. The sample material was continuously hot-dip zinc-coated high-strength constructional steel,with a nominal thickness of 1.0 mm. The minimum Rp0.2 proof stress was 637 N/mm2. Such material has not yet been used extensively in light-frame housing, and little has been published on clinching of the material. The performance of the material is therefore of particular interest. Companies that use clinching on a daily basis stand to gain the greatest benefit from the procedure. By understanding the behaviour of sheets in different cases, it is possible to use data at an early stage for adjusting and optimising the process. In particular, the functionality of common tools can be increased since it is possible to characterise the complete range of existing tools. The study increases and broadens the amount ofbasic information concerning the clinching process. New approaches and points of view are presented and used for generating new knowledge.

Evaluation and realisation of a market entry method: The entry of a small high technology company into the British construction software markets

Tutkielman tavoitteena on tutkia, mikä olisi parhaiten case-yritykselle sopiva menetelmä tulla tekemään kauppaa ulkomaan markkinoille. Kaikki yleiset kansainvälisille markkinoilletulomenetelmät esitetään ja niiden edut ja haitat tuodaan esille. Selvittäessä tehtävänantajayrityksen resurssit, odotukset ja vaatimukset todetaan, että yhteistyössä tehtävä markkinoilletulo on pätevin vaihtoehto. Tämän jälkeen valitaan parhaiten tarkoitukseen sopiva yritys ennalta valitusta yritysvaihtoehtojen ryhmästä ja testataan tämän yrityksen yhteistyösopivuus case-yrityksen kanssa. Yritysten välinen yhteistyösopivuus arvioidaan analysoimalla yritykset haastattelujen avulla ja tutkielmassa esitettyjen teorioiden avulla. Sopivuus todetaan hyväksi, kattaen 71 prosenttia analysoiduista kohdista. Kaksikymmentäyhdeksän prosenttia kohdista todetaan kohdiksi, joissa yritysten välinen yhteisymmärrys ei ole toimeksiantajayrityksen minimivaatimukset täyttävää. Näitä kohtia tullaan käyttämään suunnittelun pohjana kun suunnitellaan jatkoneuvotteluja yhteistyön käynnistämiseksi.

Infrastructure and nation building: The regulation and financing of network transportation infrastructures in Spain (1720-2010)

This paper analyzes Spanish infrastructure policy since the early 1700s: Road building in the eighteenth century, railway creation and expansion in the nineteenth, motorway expansion in the twentieth, and high speed rail development in the twenty-first. The analysis reveals a long-term pattern, in which infrastructure policy in Spain has been driven not by the requirements of commerce and economic activity, but rather by the desire to centralize transportation around the country’s political capital.

Aggregate material formulated with MSWI bottom ash and APC fly ash for use as secondary building material

The main goal of this paper is to obtain a granular material formulated with Municipal Solid Waste Incinerarion (MSWI) bottom ash (BA) and air pollution control (APC) ash to be used as secondary building material. Previously, an optimum concrete mixture using both MSWI residues as aggregates was formulated. A compromise between the environmental behaviour and the economy of the process was considered. Unconfined compressive strength and abrasion resistance values were measured in order to evaluate the mechanical properties. From these results, the granular mixture was not suited for certain applications owing to the high BA/APC content and low cement percentages used to reduce the costs of the final product. Nevertheless, the leaching test performed showed that the concentrations of all heavy metals were below the limits established by the current Catalan legislation for their reutilization. Therefore, the material studied might be mainly used in embankments, where high mechanical properties are not needed and environmental safety is assured.

High Altitude Increases Alteration in Maximal Torque but Not in Rapid Torque Development in Knee Extensors after Repeated Treadmill Sprinting.

We assessed knee extensor neuromuscular adjustments following repeated treadmill sprints in different normobaric hypoxia conditions, with special reference to rapid muscle torque production capacity. Thirteen team- and racquet-sport athletes undertook 8 × 5-s "all-out" sprints (passive recovery = 25 s) on a non-motorized treadmill in normoxia (NM; FiO2 = 20.9%), at low (LA; FiO2 = 16.8%) and high (HA; FiO2 = 13.3%) normobaric hypoxia (simulated altitudes of ~1800 m and ~3600 m, respectively). Explosive (~1 s; "fast" instruction) and maximal (~5 s; "hard" instruction) voluntary isometric contractions (MVC) of the knee extensors (KE), with concurrent electromyographic (EMG) activity recordings of the vastus lateralis (VL) and rectus femoris (RF) muscles, were performed before and 1-min post-exercise. Rate of torque development (RTD) and EMG (i.e., Root Mean Square or RMS) rise from 0 to 30, -50, -100, and -200 ms were recorded, and were also normalized to maximal torque and EMG values, respectively. Distance covered during the first 5-s sprint was similar (P > 0.05) in all conditions. A larger (P < 0.05) sprint decrement score and a shorter (P < 0.05) cumulated distance covered over the eight sprints occurred in HA (-8 ± 4% and 178 ± 11 m) but not in LA (-7 ± 3% and 181 ± 10 m) compared to NM (-5 ± 2% and 183 ± 9 m). Compared to NM (-9 ± 7%), a larger (P < 0.05) reduction in MVC torque occurred post-exercise in HA (-14 ± 9%) but not in LA (-12 ± 7%), with no difference between NM and LA (P > 0.05). Irrespectively of condition (P > 0.05), peak RTD (-6 ± 11%; P < 0.05), and normalized peak RMS activity for VL (-8 ± 11%; P = 0.07) and RF (-14 ± 11%; P < 0.01) muscles were reduced post-exercise, whereas reductions (P < 0.05) in absolute RTD occurred within the 0-100 (-8 ± 9%) and 0-200 ms (-10 ± 8%) epochs after contraction onset. After normalization to MVC torque, there was no difference in RTD values. Additionally, the EMG rise for VL muscle was similar (P > 0.05), whereas it increased (P < 0.05) for RF muscle during all epochs post-exercise, independently of the conditions. In summary, alteration in repeated-sprint ability and post-exercise MVC decrease were greater at high altitude than in normoxia or at low altitude. However, the post-exercise alterations in RTD were similar between normoxia and low-to-high hypoxia.

Role of references in international industrial marketing : a theory-building case study about supplier’s processes of utilizing references

Scientific studies regarding specifically references do not seem to exist. However, the utilization of references is an important practice for many companies involved in industrial marketing. The purpose of the study is to increase the understanding about the utilization of references in international industrial marketing in order to contribute to the development of a theory of reference behavior. Specifically, the modes of reference usage in industry, the factors affecting a supplier's reference behavior, and the question how references are actually utilized, are explored in the study. Due to the explorative nature of the study, a research design was followed where theory and empirical studies alternated. An Exploratory Framework was developed to guide a pilot case study that resulted in Framework 1. Results of the pilot study guided an expanded literature review that was used to develop first a Structural Framework and a Process Framework which were combined in Framework 2. Then, the second empirical phase of the case study was conducted in the same (pilot) case company. In this phase, Decision Systems Analysis (DSA) was used as the analysis method. The DSA procedure consists of three interviewing waves: initial interviews, reinterviews, and validating interviews. Four reference decision processes were identified, described and analyzed in the form of flowchart descriptions. The flowchart descriptions were used to explore new constructs and to develop new propositions to develop Framework 2 further. The quality of the study was ascertained by many actions in both empirical parts of the study. The construct validity of the study was ascertained by using multiple sources of evidence and by asking the key informant to review the pilot case report. The DSA method itself includes procedures assuring validity. Because of the choice to conduct a single case study, external validity was not even pursued. High reliability was pursued through detailed documentation and thorough reporting of evidence. It was concluded that the core of the concept of reference is a customer relationship regardless of the concrete forms a reference might take in its utilization. Depending on various contingencies, references might have various tasks inside the four roles of increasing 1) efficiency of sales and sales management, 2) efficiency of the business, 3) effectiveness of marketing activities, and 4) effectiveness in establishing, maintaining and enhancing customer relationships. Thus, references have not only external but internal tasks as well. A supplier's reference behavior might be affected by many hierarchical conditions. Additionally, the empirical study showed that the supplier can utilize its references as a continuous, all pervasive decision making process through various practices. The process includes both individual and unstructured decision making subprocesses. The proposed concept of reference can be used to guide a reference policy recommendable for companies for which the utilization of references is important. The significance of the study is threefold: proposing the concept of reference, developing a framework of a supplier's reference behavior and its short term process of utilizing references, and conceptual structuring of an unstructured and in industrial marketing important phenomenon to four roles.

Emerging, non-PCV13 serotypes 11A and 35B of Streptococcus pneumoniae show high potential for biofilm formation in vitro

Background: Since the use of pneumococcal conjugate vaccines PCV7 and PCV13 in children became widespread, invasive pneumococcal disease (IPD) has dramatically decreased. Nevertheless, there has been a rise in incidence of Streptococcus pneumoniae non-vaccine serotypes (NVT) colonising the human nasopharynx. Nasopharyngeal colonisation, an essential step in the development of S. pneumoniae-induced IPD, is associated with biofilm formation. Although the capsule is the main pneumococcal virulence factor, the formation of pneumococcal biofilms might, in fact, be limited by the presence of capsular polysaccharide (CPS). Methodology/Principal Findings: We used clinical isolates of 16 emerging, non-PCV13 serotypes as well as isogenic transformants of the same serotypes. The biofilm formation capacity of isogenic transformants expressing CPSs from NVT was evaluated in vitro to ascertain whether this trait can be used to predict the emergence of NVT. Fourteen out of 16 NVT analysed were not good biofilm formers, presumably because of the presence of CPS. In contrast, serotypes 11A and 35B formed >45% of the biofilm produced by the non-encapsulated M11 strain. Conclusions/Significance This study suggest that emerging, NVT serotypes 11A and 35B deserve a close surveillance.

The effects of welding heat input on the usability of high strength steels in welded structures

High strength steel (HSS) has been in use in workshops since the 1980s. At that time, the significance of the term HSS differed from the modern conception as the maximum yield strength of HSSs has increased nearly every year. There are three different ways to make HSS. The first and oldest method is QT (quenched and tempered) followed by the TMCP (thermomechanical controlled process) and DQ (direct quenching) methods. This thesis consists of two parts, the first of which part introduces the research topic and discusses welded HSS structures by characterizing the most important variables. In the second part of the thesis, the usability of welded HSS structures is examined through a set of laboratory tests. The results of this study explain the differences in the usability of the welded HSSs made by the three different methods. The results additionally indicate that usage of different HSSs in the welded structures presumes that manufacturers know what kind of HSS they are welding. As manufacturers use greater strength HSSs in welded structures, the demands for welding rise as well. Therefore, during the manufacturing process, factors such as heat input, cooling time, weld quality, and more must be under careful observation.

Identification of Some Additional Loss Components in High-Power Low-Voltage Permanent Magnet Generators

Permanent magnet generators (PMG) represent the cutting edge technology in modern wind mills. The efficiency remains high (over 90%) at partial loads. To improve the machine efficiency even further, every aspect of machine losses has to be analyzed. Additional losses are often given as a certain percentage without providing any detailed information about the actual calculation process; meanwhile, there are many design-dependent losses that have an effect on the total amount of additional losses and that have to be taken into consideration. Additional losses are most often eddy current losses in different parts of the machine. These losses are usually difficult to calculate in the design process. In this doctoral thesis, some additional losses are identified and modeled. Further, suggestions on how to minimize the losses are given. Iron losses can differ significantly between the measured no-load values and the loss values under load. In addition, with embedded magnet rotors, the quadrature-axis armature reaction adds losses to the stator iron by manipulating the harmonic content of the flux. It was, therefore, re-evaluated that in salient pole machines, to minimize the losses and the loss difference between the no-load and load operation, the flux density has to be kept below 1.5 T in the stator yoke, which is the traditional guideline for machine designers. Eddy current losses may occur in the end-winding area and in the support structure of the machine, that is, in the finger plate and the clamping ring. With construction steel, these losses account for 0.08% of the input power of the machine. These losses can be reduced almost to zero by using nonmagnetic stainless steel. In addition, the machine housing may be subjected to eddy current losses if the flux density exceeds 1.5 T in the stator yoke. Winding losses can rise rapidly when high frequencies and 10–15 mm high conductors are used. In general, minimizing the winding losses is simple. For example, it can be done by dividing the conductor into transposed subconductors. However, this comes with the expense of an increase in the DC resistance. In the doctoral thesis, a new method is presented to minimize the winding losses by applying a litz wire with noninsulated strands. The construction is the same as in a normal litz wire but the insulation between the subconductors has been left out. The idea is that the connection is kept weak to prevent harmful eddy currents from flowing. Moreover, the analytical solution for calculating the AC resistance factor of the litz-wire is supplemented by including an end-winding resistance in the analytical solution. A simple measurement device is developed to measure the AC resistance in the windings. In the case of a litz-wire with originally noninsulated strands, vacuum pressure impregnation (VPI) is used to insulate the subconductors. In one of the two cases studied, the VPI affected the AC resistance factor, but in the other case, it did not have any effect. However, more research is needed to determine the effect of the VPI on litz-wire with noninsulated strands. An empirical model is developed to calculate the AC resistance factor of a single-layer formwound winding. The model includes the end-winding length and the number of strands and turns. The end winding includes the circulating current (eddy currents that are traveling through the whole winding between parallel strands) and the main current. The end-winding length also affects the total AC resistance factor.

Building organizational creativity – a multitheory and multilevel approach for understanding and stimulating organizational creativity

Organizational creativity is increasingly important for organizations aiming to survive and thrive in complex and unexpectedly changing environments. It is precondition of innovation and a driver of an organization’s performance success. Whereas innovation research increasingly promotes high-involvement and participatory innovation, the models of organizational creativity are still mainly based on an individual-creativity view. Likewise, the definitions of organizational creativity and innovation are somewhat equal, and they are used as interchangeable constructs, while on the other hand they are seen as different constructs. Creativity is seen as generation of novel and useful ideas, whereas innovation is seen as the implementation of these ideas. The research streams of innovation and organizational creativity seem to be advancing somewhat separately, although together they could provide many synergy advantages. Thereby, this study addresses three main research gaps. First, as the knowledge and knowing is being increasingly expertized and distributed in organizations, the conceptualization of organizational creativity needs to face that perspective, rather than relying on the individual-creativity view. Thus, the conceptualization of organizational creativity needs clarification, especially as an organizational-level phenomenon (i.e., creativity by an organization). Second, approaches to consciously build organizational creativity to increase the capacity of an organization to demonstrate novelty in its knowledgeable actions are rare. The current creativity techniques are mainly based on individual-creativity views, and they mainly focus on the occasional problem-solving cases among a limited number of individuals, whereas, the development of collective creativity and creativity by the organization lacks approaches. Third, in terms of organizational creativity as a collective phenomenon, the engagement, contributions, and participation of organizational members into activities of common meaning creation are more important than the individualcreativity skills. Therefore, the development approaches to foster creativity as social, emerging, embodied, and collective creativity are needed to complement the current creativity techniques. To address these gaps, the study takes a multiparadigm perspective to face the following three objectives. The first objective of this study is to clarify and extend the conceptualization of organizational creativity. The second is to study the development of organizational creativity. The third is to explore how an improvisational theater based approach fosters organizational creativity. The study consists of two parts comprising the introductory part (part I) and six publications (part II). Each publication addresses the research questions of the thesis through detailed subquestions. The study makes three main contributions to the research of organizational creativity. First, it contributes toward the conceptualization of organizational creativity by extending the current view of organizational creativity. This study views organizational creativity as a multilevel construct constituting both of individual and collective (group and organizational) creativity. In contrast to current views of organizational creativity, this study bases on organizational (collective) knowledge that is based on and demonstrated through the knowledgeable actions of an organization as a whole. The study defines organizational creativity as an overall ability of an organization to demonstrate novelty in its knowledgeable actions (through what it does and how it does what it does).Second, this study contributes toward the development of organizational creativity as multi-level phenomena, introducing developmental approaches that face two or more of these levels simultaneously. More specifically, the study presents the cross-level approaches to building organizational creativity, by using an approach based in improvisational theater and considering assessment of organizational renewal capability. Third, the study contributes on development of organizational creativity using an improvisational theater based approach as twofold meaning. First, it fosters individual and collective creativity simultaneously and builds space for creativity to occur. Second, it models collective and distributed creativity processes, thereby, contributing to the conceptualization of organizational creativity.

Very High Energy Gamma-Rays emitting BL LAC's Population Study

Context: BL Lacs are the most numerous extragalactic objects which are detected in Very High Energy (VHE) gamma-rays band. They are a subclass of blazars. Large flux variability amplitude, sometimes happens in very short time scale, is a common characteristic of them. Significant optical polarization is another main characteristics of BL Lacs. BL Lacs' spectra have a continuous and featureless Spectral Energy Distribution (SED) which have two peaks. Among 1442 BL Lacs in the Roma-BZB catalogue, only 51 are detected in VHE gamma-rays band. BL Lacs are most numerous (more than 50% of 514 objects) objects among the sources that are detected above 10 GeV by FERMI-LAT. Therefore, many BL Lacs are expected to be discovered in VHE gamma-rays band. However, due to the limitation on current and near future technology of Imaging Air Cherenkov Telescope, astronomers are forced to predict whether an object emits VHE gamma-rays or not. Some VHE gamma-ray prediction methods are already introduced but still are not confirmed. Cross band correlations are the building blocks of introducing VHE gamma-rays prediction method. Aims: We will attempt to investigate cross band correlations between flux energy density, luminosity and spectral index of the sample. Also, we will check whether recently discovered MAGIC J2001+435 is a typical BL Lac. Methods: We select a sample of 42 TeV BL Lacs and collect 20 of their properties within five energy bands from literature and Tuorla blazar monitoring program database. All of the data are synchronized to be comparable to each other. Finally, we choose 55 pair of datasets for cross band correlations finding and investigating whether there is any correlation between each pair. For MAGIC J2001+435 we analyze the publicly available SWIFT-XRT data, and use the still unpublished VHE gamma-rays data from MAGIC collaboration. The results are compared to the other sources of the sample. Results: Low state luminosity of multiple detected VHE gamma-rays is strongly correlated luminosities in all other bands. However, the high state does not show such strong correlations. VHE gamma-rays single detected sources have similar behaviour to the low state of multiple detected ones. Finally, MAGIC J2001+435 is a typical TeV BL Lac. However, for some of the properties this source is located at the edge of the whole sample (e.g. in terms of X-rays flux). Keywords: BL Lac(s), Population study, Correlations finding, Multi wavelengths analysis, VHE gamma-rays, gamma-rays, X-rays, Optical, Radio

Building a Roadmap for a Market Intelligence function in a Global B2B company

Tämän diplomityötutkimuksen tarkoituksena on luoda markkinaälyyn (MI) erikoistunut funktio suurelle, globaalisti toimivalle B2B-yritykselle. Tämän päivän muut-tuvilla markkinoilla, teollisuusyrityksen on oltava markkinalähtöinen selviytyäkseen. Markkinatiedon tehokas hyödyntäminen ei pelkästään luo tietoa markkinoista, vaan tuottaa kilpailukykyistä tietoa ja toimii strategisen päätöksenteon tukena pitkällä aikavälillä. Tämä tutkimus on kvalitatiivinen toimintatutkimus, joka sisältää kirjallisuuskat-sauksen, yritystapaustutkimuksen sekä syväanalyysin yrityksen MI-ympäristöstä. Kirjallisuuskatsaus pitää sisällään teoriaa liittyen markkinaälyyn useassa eri kon-tekstissa, asiakassuhteeseen, sekä prosessinmallintamiseen. Empiiriseen osaa seuraa tutkimusmenetelmäkappale, joka sisältää kaksivaiheisen tutkimuksen mukaan lu-kien 20 päällikkötason haastattelua sekä yhden laaja-alaisen työryhmätapaamisen. Työn tuloksena syntyy kolmivaiheinen tiekartta, jonka tarkoitus on toimia pohjana uuden MI-funktion rakentamiselle Case-yrityksessä. Tuloksen mukaan MI-funktio tulisi sijoittaa yrityksen asiakasrajapintaan sekä tukea yksiköiden välistä integraa-tiota. Markkinaälyn jakaminen yrityksen sisällä vaatii käytäntöjen, tarpeiden ja ta-voitteiden systemaattista viestintää eri organisaatiotasoille, jotta yritys voi edelleen saada asiakkaalta tarpeeseen vastaavaa tietoa. Viestintä yrityksen ja asiakkaan välil-lä on oltava molemminpuolista, jotta tulokset voisivat parantaa asiakassuhdetta. Kun asiakassuhde paranee, yritys voi oppia asiakkaalta arvokasta tietoa, markkinaälyä.

The powerful high pressure tool for protein conformational studies

The pressure behavior of proteins may be summarized as a the pressure-induced disordering of their structures. This thermodynamic parameter has effects on proteins that are similar but not identical to those induced by temperature, the other thermodynamic parameter. Of particular importance are the intermolecular interactions that follow partial protein unfolding and that give rise to the formation of fibrils. Because some proteins do not form fibrils under pressure, these observations can be related to the shape of the stability diagram. Weak interactions which are differently affected by hydrostatic pressure or temperature play a determinant role in protein stability. Pressure acts on the 2º, 3º and 4º structures of proteins which are maintained by electrostatic and hydrophobic interactions and by hydrogen bonds. We present some typical examples of how pressure affects the tertiary structure of proteins (the case of prion proteins), induces unfolding (ataxin), is a convenient tool to study enzyme dissociation (enolase), and provides arguments to understand the role of the partial volume of an enzyme (butyrylcholinesterase). This approach may have important implications for the understanding of the basic mechanism of protein diseases and for the development of preventive and therapeutic measures.

The influence of high cable penetration in distribution networks on earth fault currents and the operation of relay protection.

Recent Storms in Nordic countries were a reason of long power outages in huge territories. After these disasters distribution networks' operators faced with a problem how to provide adequate quality of supply in such situation. The decision of utilization cable lines rather than overhead lines were made, which brings new features to distribution networks. The main idea of this work is a complex analysis of medium voltage distribution networks with long cable lines. High value of cable’s specific capacitance and length of lines determine such problems as: high values of earth fault currents, excessive amount of reactive power flow from distribution to transmission network, possibility of a high voltage level at the receiving end of cable feeders. However the core tasks was to estimate functional ability of the earth fault protection and the possibility to utilize simplified formulas for operating setting calculations in this network. In order to provide justify solution or evaluation of mentioned above problems corresponding calculations were made and in order to analyze behavior of relay protection principles PSCAD model of the examined network have been created. Evaluation of the voltage rise in the end of a cable line have educed absence of a dangerous increase in a voltage level, while excessive value of reactive power can be a reason of final penalty according to the Finish regulations. It was proved and calculated that for this networks compensation of earth fault currents should be implemented. In PSCAD models of the electrical grid with isolated neutral, central compensation and hybrid compensation were created. For the network with hybrid compensation methodology which allows to select number and rated power of distributed arc suppression coils have been offered. Based on the obtained results from experiments it was determined that in order to guarantee selective and reliable operation of the relay protection should be utilized hybrid compensation with connection of high-ohmic resistor. Directional and admittance based relay protection were tested under these conditions and advantageous of the novel protection were revealed. However, for electrical grids with extensive cabling necessity of a complex approach to the relay protection were explained and illustrated. Thus, in order to organize reliable earth fault protection is recommended to utilize both intermittent and conventional relay protection with operational settings calculated by the use of simplified formulas.

Orange Union High School, Orange, California

Orange Union High School in Orange, California, ca. 1915. Elongated postcard image shows bird's-eye view looking southeast toward the campus. The original academic building in the center was designed by local architect C.B. Bradshaw and completed in July 1905 [now Wilkinson Hall]. The "Twins," identical buildings officially known as the Science and Commercial Buildings[now Reeves Hall and Smith Hall], flank the academic building on the north and south, forming a "U." They were added in 1913 and designed by Santa Ana architect Fred Eley. The 300 block of North Glassell Street runs in front of the buildings and East Palm Avenue is on the south side. Residences can be seen in front and behind the campus. The campus was purchased by Chapman College in 1954.