The Effect of Operational Disturbances on Reliability and Operation Time Distribution of NCmachine Tools in FMS

This thesis concentrates on studying the operational disturbance behavior of machine tools integrated into FMS. Operational disturbances are short term failures of machine tools which are especially disruptive to unattended or unmanned operation of FMS. The main objective was to examine the effect of operational disturbances on reliability and operation time distribution for machine tools. The theoretical part of the thesis covers the fimdamentals of FMS relating to the subject of this study. The concept of FMS, its benefits and operator's role in FMS operation are reviewed. The importance of reliability is presented. The terms describing the operation time of machine tools are formed by adopting standards and references. The concept of failure and indicators describing reliability and operational performance for machine tools in FMSs are presented. The empirical part of the thesis describes the research methodology which is a combination of automated (ADC) and manual data collection. By using this methodology it is possible to have a complete view of the operation time distribution for studied machine tools. Data collection was carried out in four FMSs consisting of a total of 17 machine tools. Each FMS's basic features and the signals of ADC are described. The indicators describing the reliability and operation time distribution of machine tools were calculated according to collected data. The results showed that operational disturbances have a significant influence on machine tool reliability and operational performance. On average, an operational disturbance occurs every 8,6 hours of operation time and has a down time of 0,53 hours. Operational disturbances cause a 9,4% loss in operation time which is twice the amount of losses caused by technical failures (4,3%). Operational disturbances have a decreasing influence on the utilization rate. A poor operational disturbance behavior decreases the utilization rate. It was found that the features of a part family to be machined and the method technology related to it are defining the operational disturbance behavior of the machine tool. Main causes for operational disturbances were related to material quality variations, tool maintenance, NC program errors, ATC and machine tool control. Operator's role was emphasized. It was found that failure recording activity of the operators correlates with the utilization rate. The more precisely the operators record the failure, the higher is the utilization rate. Also the FMS organizations which record failures more precisely have fewer operational disturbances.

Effect of reducing and replacing pork fat on the physicochemical, instrumental and sensory characteristics throughout storage time of small caliber non-acid fermented sausages with reduced sodium content

The effect of pork fat reduction (from 44% to 20% final fat content) and its partial substitution by sunflower oil (3% addition) on the physicochemical, instrumental and sensory properties throughout storage time of small caliber non-acid fermented sausages (fuet type) with reduced sodium content (with partial substitution of NaCl by KCl and K-lactate) and without direct addition of nitrate and nitrite (natural nitrate source used instead), was studied. Results showed that sausages with reduced fat (10% initial fat content) and with acceptable sensory characteristics can be obtained by adding to the shoulder lean (8% fat content) during the grinding, either 3.3% backfat (3% fat content) or 3% sunflower oil, both previously finely comminuted with lean. Furthermore, sunflower oil showed to be suitable for partial pork backfat substitution in very lean fermented sausages, conferring desirable sensory properties similar to those of sausages with standard fat content. The sensory quality of the sausages was maintained after three-month cold storage in modified atmosphere.

Effect of metal ions on the in vitro availability of enoxacin, its in vivo implications, kinetic and antibacterial studies

The present paper describes the effect of metals ions on the in vitro availability of enoxacin (a second generation quinolone antibiotic) owing to drug-metal interaction. These interaction studies were performed at 37 °C in different pH environments simulating human body compartments and were studied by UV spectroscopic technique. In order to determine the probability of these reactions different kinetic parameters (dissolution constants (K) and free energy change (ΔG)) for these reactions were also calculated. It is proposed that the structure of enoxacin contains various electron donating sites which facilitate its binding with metallic cations forming chelates. Hence taking food products, nutritional supplements or multivitamins containing multivalent cations at the same time as enoxacin, could reduce the absorption of the drug into the circulation and thus would decrease the effectiveness of the drug. In addition, the MIC of enoxacin for various microorganisms before and after interaction with metal ions was calculated which in most cases was increased which possibly could impair the clinical efficacy of the drug.

The effect of the birth hospital and the time of birth on the outcome of Finnish very preterm infants

The purpose of this study was to evaluate the effect of the birth hospital and the time of birth on mortality and the long-term outcome of Finnish very low birth weight (VLBW) or very low gestational age (VLGA) infants. This study included all Finnish VLBW/VLGA infants born at <32 gestational weeks or with a birth weight of ≤1500g, and controls born full-term and healthy. In the first part of the study, the mortality of VLBW/VLGA infants born in 2000–2003 was studied. The second part of the study consisted of a five-year follow-up of VLBW/VLGA infants born in 2001–2002. The study was performed using data from parental questionnaires and several registers. The one-year mortality rate was 11% for live-born VLBW/VLGA infants, 22% for live-born and stillborn VLBW/VLGA infants, and 0% for the controls. In live-born and in all (including stillbirths) VLBW/VLGA infants, the adjusted mortality was lower among those born in level III hospitals compared with level II hospitals. Mortality rates of live-born VLBW/VLGA infants differed according to the university hospital district where the birth hospital was located, but there were no differences in mortality between the districts when stillborn infants were included. There was a trend towards lower mortality rates in VLBW/VLGA infants born during office hours compared with those born outside office hours (night time, weekends, and public holidays). When stillborn infants were included, this difference according to the time of birth was significant. Among five-year-old VLBW/VLGA children, morbidity, use of health care resources, and problems in behaviour and development were more common in comparison with the controls. The health-related quality of life of the surviving VLBW/VLGA children was good but, statistically, it was significantly lower than among the controls. The median and the mean number of quality-adjusted life-years were 4.6 and 3.6 out of a maximum five years for all VLBW/VLGA children. For the controls, the median was 4.8 and the mean was 4.9. Morbidity rates, the use of health care resources, and the mean quality-adjusted life-years differed for VLBW/VLGA children according to the university hospital district of birth. However, the time of birth, the birth hospital level or university hospital district were not associated with the health-related quality of life, nor with behavioural and developmental scores of the survivors at the age of five years. In conclusion, the decreased mortality in level III hospitals was not gained at the expense of long-term problems. The results indicate that VLBW/VLGA deliveries should be centralized to level III hospitals and the regional differences in the treatment practices should further be clarified. A long-term follow-up on the outcome of VLBW/VLGA infants is important in order to recognize the critical periods of care and to optimise the care. In the future, quality-adjusted life-years can be used as a uniform measure for comparing the effectiveness of care between VLBW/VLGA infants and different patient groups

Effect of time-temperature binomial in obtaining biochemical oxygen demand of different wastewaters

Studies on the effects of temperature and time of incubation of wastewater samples for the estimation of biodegradable organic matter through the biochemical oxygen demand (BOD), that nowadays are rare, considering that the results of the classic study of STREETER & PHELPS(1925) have been accepted as standard. However, there are still questions how could be possible to reduce the incubation time; whether the coefficient of temperature (θ) varies with the temperature and with the type of wastewater and if it approaches 1.047. Aiming the elucidation of these questions, wastewater samples of dairy, swine and sewage treated in septic tanks were incubated at temperatures of 20, 30 and 35 °C, respectively for 5, 3.16 and 2.5 days. From the parameter of deoxygenation coefficient at 20 °C (k20), θ30 and θ35 were calculated. The results indicated that θ values changes with the type of wastewater, however does not vary in the temperature range between 30 and 35 °C, and that the use of 1.047 value did not implied significant differences in obtaining k in a determined T temperature. Thus, it is observed that the value of θ can be used to estimate the required incubation time of the samples at different temperatures.

Effect of cycle time and airflow in biological nitrogen removal from poultry slaughterhouse wastewater using sequencing batch reactor

This study aimed to evaluate the influence of airflow (0.25, 0.50 and 0.75 L.L-1.min-1) and cycle time (10.45 h, 14.25 h and 17.35 h) on a sequencing batch reactor (SBR) performance in promoting nitrification and denitrification of poultry slaughterhouse wastewater. The operational stages included feeding, aerobic and anoxic reactions, sedimentation and discharge. SBR was operated in a laboratory scale with a working volume of 4 L, keeping 25% of biomass retained inside the reactor as inoculum for the next batch. In the anoxic stage, C: N ratio was maintained between 5 and 6 by adding cassava starch wastewater. A factorial design (22) with five repetitions was designed at the central point to evaluate the influence of cycle time and airflow on total inorganic nitrogen removal (N-NH4++N-NO2-+N-NO3-) and in the whole process (nitrification and denitrification). The highest total inorganic nitrogen removal (93.3%) was observed for airflow of 0.25 L.L-1.min‑1 and a cycle time of 14.25 h. At the end of the experiment, the sludge inside the reactor was characterized by fluorescent in situ hybridization (FISH), indicating the presence of ammonia and nitrite oxidizing bacteria.

Gap effect and reaction time distribution: simple vs choice manual responses

It is well known that saccadic reaction times (SRT) are reduced when the target is preceded by the offset of the fixation point (FP) - the gap effect. Some authors have proposed that the FP offset also allows the saccadic system to generate a separate population of SRT, the express saccades. Nevertheless, there is no agreement as to whether the gap effect and express responses are also present for manual reaction times (MRT). We tested the gap effect and the MRT distribution in two different conditions, i.e., simple and choice MRT. In the choice MRT condition, subjects need to identify the side of the stimulus and to select the appropriate response, while in the simple MRT these stages are not necessary. We report that the gap effect was present in both conditions (22 ms for choice MRT condition; 15 ms for simple MRT condition), but, when analyzing the MRT distributions, we did not find any clear evidence for express manual responses. The main difference in MRT distribution between simple and choice conditions was a shift towards shorter values for simple MRT.

Inhibition of return, gap effect and saccadic reaction time to a visual target

Simple manual reaction time (MRT) to a visual target (S2) is shortened when a non-informative cue (S1) is flashed at the S2 location shortly before the onset of S2 (early facilitation). Afterwards, MRT to S2 appearing at the S1 location is lengthened (inhibition of return - IOR). Similar results have been obtained for saccadic reaction time (SRT). Moreover, when there is a temporal gap between offset of the fixation point (FP) and onset of a target (gap paradigm), SRT is shorter than SRT in an overlap paradigm (FP remains on). In the present study, we determined SRT to S2 (10º) after presenting S1 at the same eccentricity (10º) or at a parafoveal position (2º) in the same or in the opposite hemifield. In addition, we employed both gap and overlap paradigms. Twelve subjects were asked not to respond to S1 (2º or 10º) to the right or to the left of FP, but to respond by making a saccadic movement in response to S2. We obtained the following results: 1) a 40-ms gap effect, 2) an interaction between gap effect and IOR, 3) a 39-ms delay (IOR) when S2 appeared at the cued (S1) position, and 4) a smaller (17 ms) but significant inhibition when S1 occurred at 2º in the ipsilateral hemifield. Thus, a parafoveal (2º) S1 elicits an inhibition of SRT towards ipsilateral peripheral targets. Since an inhibition of the ipsilateral hemifield by a 1º eccentric cue has been reported to occur when manual responses are employed, we suggest that the postulated functional link between covert and overt orienting of attention is also valid for parafoveal cues.

Looking for the GAP effect in manual responses and the role of contextual influences in reaction time experiments

When the offset of a visual stimulus (GAP condition) precedes the onset of a target, saccadic reaction times are reduced in relation to the condition with no offset (overlap condition) - the GAP effect. However, the existence of the GAP effect for manual responses is still controversial. In two experiments using both simple (Experiment 1, N = 18) and choice key-press procedures (Experiment 2, N = 12), we looked for the GAP effect in manual responses and investigated possible contextual influences on it. Participants were asked to respond to the imperative stimulus that would occur under different experimental contexts, created by varying the array of warning-stimulus intervals (0, 300 and 1000 ms) and conditions (GAP and overlap): i) intervals and conditions were randomized throughout the experiment; ii) conditions were run in different blocks and intervals were randomized; iii) intervals were run in different blocks and conditions were randomized. Our data showed that no GAP effect was obtained for any manipulation. The predictability of stimulus occurrence produced the strongest influence on response latencies. In Experiment 1, simple manual responses were shorter when the intervals were blocked (247 ms, P < 0.001) in relation to the other two contexts (274 and 279 ms). Despite the use of choice key-press procedures, Experiment 2 produced a similar pattern of results. A discussion addressing the critical conditions to obtain the GAP effect for distinct motor responses is presented. In short, our data stress the relevance of the temporal allocation of attention for behavioral performance.

Effect of the time-of-day of training on explicit memory

Studies have shown a time-of-day of training effect on long-term explicit memory with a greater effect being shown in the afternoon than in the morning. However, these studies did not control the chronotype variable. Therefore, the purpose of this study was to assess if the time-of-day effect on explicit memory would continue if this variable were controlled, in addition to identifying the occurrence of a possible synchronic effect. A total of 68 undergraduates were classified as morning, intermediate, or afternoon types. The subjects listened to a list of 10 words during the training phase and immediately performed a recognition task, a procedure which they repeated twice. One week later, they underwent an unannounced recognition test. The target list and the distractor words were the same in all series. The subjects were allocated to two groups according to acquisition time: a morning group (N = 32), and an afternoon group (N = 36). One week later, some of the subjects in each of these groups were subjected to a test in the morning (N = 35) or in the afternoon (N = 33). The groups had similar chronotypes. Long-term explicit memory performance was not affected by test time-of-day or by chronotype. However, there was a training time-of-day effect [F (1,56) = 53.667; P = 0.009] with better performance for those who trained in the afternoon. Our data indicated that the advantage of training in the afternoon for long-term memory performance does not depend on chronotype and also that this performance is not affected by the synchronic effect.

Effect of carbohydrate availability on time to exhaustion in exercise performed at two different intensities

This study examined the effects of pre-exercise carbohydrate availability on the time to exhaustion for moderate and heavy exercise. Seven men participated in a randomized order in two diet and exercise regimens each lasting 3 days with a 1-week interval for washout. The tests were performed at 50% of the difference between the first (LT1) and second (LT2) lactate breakpoint for moderate exercise (below LT2) and at 25% of the difference between the maximal load and LT2 for heavy exercise (above LT2) until exhaustion. Forty-eight hours before each experimental session, subjects performed a 90-min cycling exercise followed by 5-min rest periods and a subsequent 1-min cycling bout at 125% VO2max/1-min rest periods until exhaustion to deplete muscle glycogen. A diet providing 10% (CHOlow) or 65% (CHOmod) energy as carbohydrates was consumed for 2 days until the day of the experimental test. In the exercise below LT2, time to exhaustion did not differ between the CHOmod and the CHOlow diets (57.22 ± 24.24 vs 57.16 ± 25.24 min). In the exercise above LT2, time to exhaustion decreased significantly from 23.16 ± 8.76 min on the CHOmod diet to 18.30 ± 5.86 min on the CHOlow diet (P < 0.05). The rate of carbohydrate oxidation, respiratory exchange ratio and blood lactate concentration were reduced for CHOlow only during exercise above LT2. These results suggest that muscle glycogen depletion followed by a period of a low carbohydrate diet impairs high-intensity exercise performance.

Effect of melatonin and time of administration on irradiation-induced damage to rat testes

The effect of ionizing irradiation on testes and the protective effects of melatonin were investigated by immunohistochemical and electron microscopic methods. Eighty-two adult male Wistar rats were divided into 10 groups. The rats in the irradiated groups were exposed to a sublethal irradiation dose of 8 Gy, either to the total body or abdominopelvic region using a 60Co source at a focus of 80 cm away from the skin in the morning or evening together with vehicle (20% ethanol) or melatonin administered 24 h before (10 mg/kg), immediately before (20 mg/kg) and 24 h after irradiation (10 mg/kg), all ip. Caspace-3 immunoreactivity was increased in the irradiated group compared to control (P < 0.05). Melatonin-treated groups showed less apoptosis as indicated by a considerable decrease in caspace-3 immunoreactivity (P < 0.05). Electron microscopic examination showed that all spermatogenic cells, especially primary spermatocytes, displayed prominent degeneration in the groups submitted to total body and abdominopelvic irradiation. However, melatonin administration considerably inhibited these degenerative changes, especially in rats who received abdominopelvic irradiation. Total body and abdominopelvic irradiation induced identical apoptosis and testicular damage. Chronobiological assessment revealed that biologic rhythm does not alter the inductive effect of irradiation. These data indicate that melatonin protects against total body and abdominopelvic irradiation. Melatonin was more effective in the evening abdominopelvic irradiation and melatonin-treated group than in the total body irradiation and melatonin-treated group.

Effect of blanching time on selective mineral elements extraction from the spinach substitute (Tetragonia expansa) commonly used in Brazil

The true spinach (Spinacia oleracea) does not grow well in warm climates and for that reason is not commercialized in Brazil. Instead, a spinach substitute (Tetragonia expansa), originally from New Zealand, is widely used in the country. There is scant information on the mineral profile and none on the soluble mineral fraction of this vegetable. The solubility of a mineral is one of the important factors for its absorption. For this reason, the calcium, magnesium, iron, manganese, copper, zinc, potassium, and sodium soluble fractions in the raw spinach substitute were determined and the effect of blanching times on the solubility of these minerals was investigated. Blanching times of 1, 5, and 15 minutes were employed. The magnesium, manganese, potassium, and sodium soluble fractions increased sizably with shorter blanching time. Longer blanching time (15 minutes) caused large losses of minerals. The soluble mineral fractions can contribute poorly to diet in terms of potassium, magnesium, manganese, and zinc. The spinach substitute cannot be considered a dietary source of calcium, iron and copper due to the insolubility of these minerals in the vegetable, possibly caused by the large oxalate content.

Influence of different sanitizers on food contaminant bacteria: effect of exposure temperature, contact time, and product concentration

The efficiency of four Sanitizers - peracetic acid, chlorhexidine, quaternary ammonium, and organic acids - was tested in this work using different bacteria recognized as a problem to meat industry, Salmonella sp., S. aureus, E. coli and L. monocytogenes. The effects of sanitizer concentration (0.2, 0.5, 0.6, 1.0, 1.1 and 1.4%), at different temperatures (10 and 45 °C) and contact time (2, 10, 15, 18 and 25 minutes) were evaluated. Tests in an industrial plant were also carried out considering previously obtained results. In a general way, peracetic acid presented higher efficiencies using low concentration (0.2%) and contact time (2 minutes) at 10 °C. The tests performed in industrial scale showed that peracetic acid presented a good performance in concentration and contact time lower than that suggested by the suppliers. The use of chlorhexidine and quaternary ammonium led to reasonable results at the indicated conditions, and organic acids were ineffective under concentration and contact time higher than those indicated by the suppliers in relation to Staphylococcus aureus. The results, in general, show that the choice for the most adequate sanitizer depends on the microorganism contaminant, the time available for sanitizer application, and also on the process cost.

Effect of different tumbling marination methods and time on the quality characteristics of prepared pork chops

AbstractThe combined effects of tumbling marination methods (Vacuum continuous tumbling marination, CT; Vacuum intermittent tumbling marination, IT) and effective tumbling time (4, 6, 8 and 10 h) on quality characteristics of prepared boneless pork chops were investigated. The results showed that regardless of tumbling time, CT method significantly increased the pH, product yield, cohesiveness, resilience, sensory tenderness and overall flavor (p<0.05) compared with IT method, and CT method also significantly decreased the pressing loss, cooking loss, shear force value (SFV), hardness and chewiness (p<0.05) compared with IT method. With the effective tumbling time increasing from 4 h to 10 h, the product yield and sensory attributes of prepared pork chops increased at first and then decreased, whereas the pressing loss, cooking loss, SFV, hardness and chewiness decreased at first and then increased. Additionally, an interaction between CT method and effective tumbling time was also observed. These results suggested that CT method of 8 h obtained the best quality characteristics of prepared pork chops, which should be adopted.