Effect of drying method on the adsorption isotherms and isosteric heat of passion fruit pulp powder

The sorption behavior of dry products is generally affected by the drying method. The sorption isotherms are useful to determine and compare thermodynamic properties of passion fruit pulp powder processed by different drying methods. The objective of this study is to analyze the effects of different drying methods on the sorption properties of passion fruit pulp powder. Passion fruit pulp powder was dehydrated using different dryers: vacuum, spray dryer, vibro-fluidized, and freeze dryer. The moisture equilibrium data of Passion Fruit Pulp (PFP) powders with 55% of maltodextrin (MD) were determined at 20, 30, 40 and 50 ºC. The behavior of the curves was type III, according to Brunauer's classification, and the GAB model was fitted to the experimental equilibrium data. The equilibrium moisture contents of the samples were little affected by temperature variation. The spray dryer provides a dry product with higher adsorption capacity than that of the other methods. The vibro-fluidized bed drying showed higher adsorption capacity than that of vacuum and freeze drying. The vacuum and freeze drying presented the same adsorption capacity. The isosteric heats of sorption were found to decrease with increasing moisture content. Considering the effect of drying methods, the highest isosteric heat of sorption was observed for powders produced by spray drying, whereas powders obtained by vacuum and freeze drying showed the lowest isosteric heats of sorption.

Kiertoleijupetikattilateknologia ja sen matemaattinen mallinnus energiantuotantoprosessissa

Työn teoreettisessa osuudessa tehdään katsaus kiertoleijupetiteknologian eri osa-alueisiin: leijupedin virtausdynamiikkaan, hiukkaserottimeen ja kiintoaineen palautusmekanismiin. Myös teknologian historiaa ja muita käyttötarkoituksia energiantuotannon ohella käydään läpi. Termodynamiikkaa sekä lämmönsiirron ja voimalaitosprosessien teoriaa käsitellään mallinnuksessa tarvittavilta osin. Mallinnusosiossa käydään läpi kiertoleijupetihöyrykattilan matemaattisen mallin tekoprosessia. Malli perustuu yleisesti saatavilla oleviin yhtälöihin ja korrelaatioihin. Mallintaminen koostuu höyrykattilan jakamisesta lämpöpintoihin ja niiden mitoittamisesta. Mallissa esitetään myös näkemys siitä, miten lämpö siirtyy savukaasuun ja miten petimateriaalin kierto tapahtuu tulipesässä.

Production of magnesium carbonates from serpentinites for CO2 mineral sequestration : optimisation towards industrial application

Global warming is one of the most alarming problems of this century. Initial scepticism concerning its validity is currently dwarfed by the intensification of extreme weather events whilst the gradual arising level of anthropogenic CO2 is pointed out as its main driver. Most of the greenhouse gas (GHG) emissions come from large point sources (heat and power production and industrial processes) and the continued use of fossil fuels requires quick and effective measures to meet the world’s energy demand whilst (at least) stabilizing CO2 atmospheric levels. The framework known as Carbon Capture and Storage (CCS) – or Carbon Capture Utilization and Storage (CCUS) – comprises a portfolio of technologies applicable to large‐scale GHG sources for preventing CO2 from entering the atmosphere. Amongst them, CO2 capture and mineralisation (CCM) presents the highest potential for CO2 sequestration as the predicted carbon storage capacity (as mineral carbonates) far exceeds the estimated levels of the worldwide identified fossil fuel reserves. The work presented in this thesis aims at taking a step forward to the deployment of an energy/cost effective process for simultaneous capture and storage of CO2 in the form of thermodynamically stable and environmentally friendly solid carbonates. R&D work on the process considered here began in 2007 at Åbo Akademi University in Finland. It involves the processing of magnesium silicate minerals with recyclable ammonium salts for extraction of magnesium at ambient pressure and 400‐440⁰C, followed by aqueous precipitation of magnesium in the form of hydroxide, Mg(OH)2, and finally Mg(OH)2 carbonation in a pressurised fluidized bed reactor at ~510⁰C and ~20 bar PCO2 to produce high purity MgCO3. Rock material taken from the Hitura nickel mine, Finland, and serpentinite collected from Bragança, Portugal, were tested for magnesium extraction with both ammonium sulphate and bisulphate (AS and ABS) for determination of optimal operation parameters, primarily: reaction time, reactor type and presence of moisture. Typical efficiencies range from 50 to 80% of magnesium extraction at 350‐450⁰C. In general ABS performs better than AS showing comparable efficiencies at lower temperature and reaction times. The best experimental results so far obtained include 80% magnesium extraction with ABS at 450⁰C in a laboratory scale rotary kiln and 70% Mg(OH)2 carbonation in the PFB at 500⁰C, 20 bar CO2 pressure for 15 minutes. The extraction reaction with ammonium salts is not at all selective towards magnesium. Other elements like iron, nickel, chromium, copper, etc., are also co‐extracted. Their separation, recovery and valorisation are addressed as well and found to be of great importance. The assessment of the exergetic performance of the process was carried out using Aspen Plus® software and pinch analysis technology. The choice of fluxing agent and its recovery method have a decisive sway in the performance of the process: AS is recovered by crystallisation and in general the whole process requires more exergy (2.48–5.09 GJ/tCO2sequestered) than ABS (2.48–4.47 GJ/tCO2sequestered) when ABS is recovered by thermal decomposition. However, the corrosive nature of molten ABS and operational problems inherent to thermal regeneration of ABS prohibit this route. Regeneration of ABS through addition of H2SO4 to AS (followed by crystallisation) results in an overall negative exergy balance (mainly at the expense of low grade heat) but will flood the system with sulphates. Although the ÅA route is still energy intensive, its performance is comparable to conventional CO2 capture methods using alkanolamine solvents. An energy‐neutral process is dependent on the availability and quality of nearby waste heat and economic viability might be achieved with: magnesium extraction and carbonation levels ≥ 90%, the processing of CO2‐containing flue gases (eliminating the expensive capture step) and production of marketable products.

Puu- ja turvetuhkan hyötykäyttökelpoisuuteen vaikuttavat tekijät pienillä polttolaitoksilla

Energiantuotannossa syntyvä tuhka voi olla laadultaan hyvin vaihtelevaa ja laadunvaihtelulle on haastavaa löytää yksiselitteistä syy-seuraussuhdetta. Ympäristönsuojelulainsäädäntö ja taloudelliset intressit ohjaavat tuhkantuottajia etsimään tuhkalle sopivia hyötykäyttökohteita, ja sen vuoksi tuhkan laatuun ja hyötykäyttökelpoisuuteen vaikuttavia tekijöitä on tarpeen selvittää. Tässä diplomityössä on tutkittu pienissä, alle 50 MW:n polttolaitoksissa syntyvää tuhkaa. Tavoitteena oli selvittää, kuinka tuhkan hyötykäyttökelpoisuuteen voidaan vaikuttaa. Tutkimuksen kohteena oli polttoainekoostumuksen, poltto-olosuhteiden ja tuhkan jälkikäsittelyn vaikutus tuhkassa olevien haitta-aineiden pitoisuuksiin ja liukoisuuksin. Työhön sisältyi myös aiemmin tehtyjen tuhka-analyysien tarkastelu sekä tuhkakokeet kahdella kohderyhmään kuuluvalla laitoksella. Työssä todettiin lentotuhkan haitta-ainepitoisuuksien ja -liukoisuuksien olevan keskimäärin korkeampia kuin pohjatuhkan vastaavien, ja että tyypillisesti arinakattilan tuhkien haitta-aineet ylittävät useammin hyötykäyttökelpoisuuden raja-arvoja kuin kuplaleijupetikattilan tuhkien. Lisäksi havaittiin metsätähdehaketuhkan kelpaavan useammin hyötykäyttöön kuin rankahaketuhkan.

Effect of Material Recycling on the Feasibility of Solid Recovered Fuel Fired Power Plant

This master’s thesis examines the effects of increased material recycling on different waste-to-energy concepts. With background study and a developed techno-economic computational method the feasibility of chosen scenarios with different combinations of mechanical treatment and waste firing technologies can be evaluated. The background study covers the waste scene of Finland, and potential market areas Poland and France. Calculated cases concentrate on municipal solid waste treatment in the Finnish operational environment. The chosen methodology to approach the objectives is techno-economic feasibility assessment. It combines calculation methods of literature and practical engineering to define the material and energy balances in chosen scenarios. The calculation results together with other operational and financial data can be concluded to net present values compared between the scenarios. For the comparison, four scenarios, most vital and alternative between each other, are established. The baseline scenario is grate firing of source separated mixed municipal solid waste. Second scenario is fluidized bed combustion of solid recovered fuel produced in mechanical treatment process with metal separation. Third scenario combines a biomaterial separation process to the solid recovered fuels preparation and in the last scenario plastics are separated in addition to the previous operations. The results indicated that the mechanical treatment scenarios still need to overcome some problems to become feasible. Problems are related to profitability, residue disposal and technical reliability. Many uncertainties are also related to the data gathered over waste characteristics, technical performance and markets. With legislative support and development of further processing technologies and markets of the recycled materials the scenarios with biomaterial and plastic separation may operate feasibly in the future.

Tutkimuskattilan taselaskenta

Diplomityön tavoitteena oli luoda Varkauden energiatutkimuskeskuksen tutkimuskäyttöön tarkoitetun kuplapetikattilan tase- ja säätölaskenta. Työssä on esitelty yleisesti kuplapetikattiloiden teoriaa ja tarkasteltu lyhyesti kuplapetikattilan muodostamaa kokonaisuutta energiantuotannossa. Työssä käsitelty tutkimuskattila ei ehtinyt valmistua ennen tätä diplomityötä, joten mittauksia käytön ajalta ei voitu suorittaa ja sisällyttää tähän työhön. Lisäksi mahdolliset käytössä havaittavat korjaukset ja parannukset taselaskentaan jäivät tämän työn tarkastelun ulkopuolelle. Taselaskennan muodostamisessa hyödynnettiin kattilan suunnitteluvaiheessa luotuja säätö- ja PI-kaavioita. Säätömekaniikkaa luodessa huomioitiin mahdollisimman tarkasti automaatiojärjestelmän vaatimukset ja suorituskyky. Työssä on esitetty suuri määrä kattilalaskennan kannalta keskeisiä yhtälöitä. Prosessia ja säätömekaniikkaa mallinnettiin laskentaperusteisesti, työssä on esitetty yhtälöistä saatavat tulokset kattilaa ajettaessa tyypillisillä arvoilla 100 %:n teholla. Työn tuloksena tutkimuskattilalle saatiin säätömekaniikka, jolla pystytään arvioimaan viipymäaikaa kattilassa. Lasketun viipymäajan avulla polttoprosessi kattilassa voidaan suunnitella ja suorittaa tutkimuskäyttöön vaaditulla tarkkuudella ja laissa säädettyjen määräyksien mukaan, mikäli kierrätyspolttoainetta käytetään yli 50 tonnia vuodessa.

Desenvolvimento de uma unidade pirolítica com reator de cilindro rotativo: obtenção de bio-óleo

The demand for alternative sources of energy drives the technological development so that many fuels and energy conversion processes before judged as inadequate or even non-viable, are now competing fuels and so-called traditional processes. Thus, biomass plays an important role and is considered one of the sources of renewable energy most important of our planet. Biomass accounts for 29.2% of all renewable energy sources. The share of biomass energy from Brazil in the OIE is 13.6%, well above the world average of participation. Various types of pyrolysis processes have been studied in recent years, highlighting the process of fast pyrolysis of biomass to obtain bio-oil. The continuous fast pyrolysis, the most investigated and improved are the fluidized bed and ablative, but is being studied and developed other types in order to obtain Bio-oil a better quality, higher productivity, lower energy consumption, increased stability and process reliability and lower production cost. The stability of the product bio-oil is fundamental to designing consumer devices such as burners, engines and turbines. This study was motivated to produce Bio-oil, through the conversion of plant biomass or the use of its industrial and agricultural waste, presenting an alternative proposal for thermochemical pyrolysis process, taking advantage of particle dynamics in the rotating bed that favors the right gas-solid contact and heat transfer and mass. The pyrolyser designed to operate in a continuous process, a feeder containing two stages, a divisive system of biomass integrated with a tab of coal fines and a system of condensing steam pyrolytic. The prototype has been tested with sawdust, using a complete experimental design on two levels to investigate the sensitivity of factors: the process temperature, gas flow drag and spin speed compared to the mass yield of bio-oil. The best result was obtained in the condition of 570 oC, 25 Hz and 200 cm3/min, temperature being the parameter of greatest significance. The mass balance of the elementary stages presented in the order of 20% and 37% liquid pyrolytic carbon. We determined the properties of liquid and solid products of pyrolysis as density, viscosity, pH, PCI, and the composition characterized by chemical analysis, revealing the composition and properties of a Bio-oil.

Obtenção de sistemas multiparticulados de isoniazida revestidos com polímero de liberação entérica

Known for thousands of years, tuberculosis (TB) is the leading cause of mortality by a single infectious disease due to lack of patient adherence to available treatment regimens, the rising of multidrug resistant strains of TB (MDR-TB) and co-infection with HIV virus. Isoniazid and rifampicin are the most powerful bactericidal agents against M. tuberculosis. Because of that, this couple of drugs becomes unanimity in anti-TB treatment around the world. However, the rifampicin in acidic conditions in the stomach can be degraded rapidly, especially in the presence of isoniazid, which reduces the amount of available drug for absorption, as well as its bioavailability, contributing to the growing resistance to tuberculostatic drugs. Rifampicin is well absorbed in the stomach because of its high solubility between pH 1 and 2 and the gastric absorption of isoniazid is considered poor, therefore it is mostly intestinal. This work has as objective the development of gastro-resistant multiple-systems (granules and pellets) of isoniazid aiming to prevent the contact with rifampicin, with consequent degradation in acid stomach and modulate the release of isoniazid in the intestine. Granules of isoniazid were obtained by wet method using both alcoholic and aqueous solutions of PVP K-30 as aggregating and binder agent, at proportions of 5, 8 and 10%. The influence of the excipients (starch, cellulose or filler default) on the physical and technological properties of the granules was investigated. The pellets were produced by extrusionesferonization technique using isoniazid and microcrystalline cellulose MC 101 (at the proportion of 85:15) and aqueous solution of 1% Methocel as platelet. The pellets presented advantages over granular, such as: higher apparent density, smaller difference between apparent and compaction densities, smoother surface and, especially, smaller friability, and then were coated with an organic solution of Acrycoat L 100 ® in a fluidized bed. Different percentages of coating (15, 25 and 50%) were applied to the pellets which had their behavior evaluated in vitro by dissolution in acidic and basic medium. Rifampicin dissolution in the presence of uncoated and coated isoniazid pellets was evaluated too. The results indicate that the gastro resistance was only achieved with the greatest amount of coating and isoniazid is released successfully in basic step. The amount of rifampicin in the dissolution medium when the isoniazid pellets were not coated was lower than in the presence of enteric release pellets. Therefore, the polymer Acrycoat L 100 ® was efficient for coating with gastro-resistant function and can solve the problem of low bioavailability of rifampicin and help to reduce its dosage

In vitro drug permeation from chitosan pellets

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Transferência de oxigênio em reatores de leito fluidizado com circulação em tubos concêntricos em meios bifásico e trifásico com variação da relação entre diâmetros

A eficiência do reator de leito fluidizado com circulação em tubos concêntricos depende das condições hidrodinâmicas que influem na transferência de oxigênio ao biofilme. Este trabalho investigou a influência da relação entre diâmetros dos tubos e da concentração de meio suporte (areia), sobre o coeficiente global de transferência de oxigênio (K La). Os ensaios - em reatores de 2,6 m de altura, com diâmetro externo de 250 mm e internos de 100, 125, 150 e 200 mm - empregaram vazões de ar até 2.500 L.h-1 e concentrações de até 150 g.L-1 de areia. O K La aumentou ligeiramente com 30 g.L-1 e diminuiu para concentrações maiores, confirmando relatos da literatura em condições semelhantes. Um modelo para K La em meio bifásico foi ajustado para as diversas relações ensaiadas entre a área externa e a interna, postulando-se uma redução na razão entre a transferência na fase líquida e o diâmetro da bolha com o aumento da vazão de ar.

Desempenho de reatores aeróbios de leito fluidizado com circulação interna na remoção de matéria carbonácea tratando diferentes águas residuárias

The organic matter. (OM) removal efficiency in the biochemical oxygen demand (BOD) and chemical oxygen demand (COD) forms for domestic wastewater and semi-intensive fish culture effluents by using three phase aerobic fluidized bed reactors with circulation in concentric tubes was studied. Three different ratios between external and internal areas by different internal diameter configurations (100, 125 and 150mm) to the same external diameter of 250mm were used; sand for filters and granulated activated carbon were used as supporting media. The reactors were tested for three hydraulic retention times: 11.5min to the R100, and 3h for the R125 and R150 reactors. The results demonstrated that this kind of reactors had good performance in the BOD and COD removal for different concentrations of waste waters. BOD mean removal efficiencies obtained were: 47% at the R100 reactor, 57% and 93% of raw and filtered BOD respectively at R125, 48 and 89% of raw and filtered BOD at R150. The COD mean calculated removal efficiencies were: 75% at the R100 reactor, 56 and 86% of raw and filtered COD at R125, and 54 and 86% of raw and filtered COD at R150. In the case of domestic wastewater it is necessary to provide a solids removal system at the reactor outflow in order to increase the removal of suspended OM from the final effluent.