Catalytic combustion of toluene on Pt zeolite coated cordierite foams

The catalytic properties of Pt based cordierite foam catalysts have been evaluated in catalytic combustion of toluene (800 ppm in air). The catalysts contain identical Pt content (0.1%) which was introduced by three different ways: Pt ion exchange on MFI zeolite and then coating on the foam; Pt ion exchange after zeolite coating and finally Pt directly wet impregnated on the cordierite foam. The catalytic behaviour of Pt foam based catalysts was compared with that of PtMFI zeolite under powder form. Pt exchanged MFI supported on the cordierite foams present an improvement of activity for toluene combustion of about 50 degrees C on the light off temperature (T-50%). The enhanced performance of the structured catalysts is due not only to the open structure of foams and homogeneous thin layers catalyst deposited on their cell walls, but also to the fact that the size and location of Pt particles present in MFI zeolite are changed during the dipping step. Indeed, as prepared Pt samples and those used in the preparation of the slurry were observed by transmission electron microscopy revealing that the chemical interaction of PtMFI zeolite with the binder and detergent, both present in the slurry, leads to an increase of Pt particles size which were found to migrate from internal pores to the external surface of zeolite crystallites thereby increasing catalytic activity. (C) 2011 Elsevier B.V. All rights reserved.

Produção de hidrogénio através da gasificação da biomassa

A procura de uma forma limpa de combustível, aliada à crescente instabilidade de preços dos combustíveis fósseis verificada nos mercados faz com que o hidrogénio se torne num combustível a considerar devido a não resultar qualquer produto poluente da sua queima e de se poder utilizar, por exemplo, desperdícios florestais cujo valor de mercado não está inflacionado por não pertencer à cadeia alimentar humana. Este trabalho tem como objetivo simular o processo de gasificação de biomassa para produção de hidrogénio utilizando um gasificador de leito fluidizado circulante. O oxigénio e vapor de água funcionam como agentes gasificantes. Para o efeito usou-se o simulador de processos químicos ASPEN Plus. A simulação desenvolvida compreende três etapas que ocorrem no interior do gasificador: pirólise, que foi simulada por um bloco RYIELD, combustão de parte dos compostos voláteis, simulada por um bloco RSTOIC e, por fim, as reações de oxidação e gasificação do carbonizado “char”, simuladas por um bloco RPLUG. Os valores de rendimento dos compostos após a pirólise, obtidos por uma correlação proposta por Gomez-Barea, et al. (2010), foram os seguintes: 20,33% “char”, 22,59% alcatrão, 36,90% monóxido de carbono, 16,05%m/m dióxido de carbono, 3,33% metano e 0,79% hidrogénio (% em massa). Como não foi possível encontrar valores da variação da composição do gás à saída do gasificador com a variação da temperatura, para o caso de vapor de água e oxigénio, optou-se por utilizar apenas vapor na simulação de forma a comparar os seus valores com os da literatura. Às temperaturas de 700, 770 e 820ºC, para um “steam-to-biomass ratio”, (SBR) igual a 0,5, os valores da percentagem molar de monóxido de carbono foram, respetivamente, 56,60%, 55,84% e 53,85%, os valores de hidrogénio foram, respetivamente, 17,83%, 18,25% e 19,31%, os valores de dióxido de carbono foram, respetivamente, 16,40%, 16,85% e 17,93% e os valores de metano foram, respetivamente, 9,00%, 8,95% e 8,83%. Os valores da composição à saída do gasificador, à temperatura de 820ºC, para um SBR de 0,5 foram: 53,85% de monóxido de carbono, 19,31% de hidrogénio, 17,93% de dióxido de carbono e 8,83% de metano (% em moles). Para um SBR de 0,7 a composição à saída foi de 54,45% de monóxido de carbono, 19,01% de hidrogénio, 17,59% de dióxido de carbono e 8,87% de metano. Por fim, quando SBR foi igual a 1 a composição do gás à saída foi de 55,08% de monóxido de carbono, 18,69% de hidrogénio, 17,24% de dióxido de carbono e 8,90% de metano. Os valores da composição obtidos através da simulação, para uma mistura de ar e vapor de água, ER igual a 0,26 e SBR igual a 1, foram: 34,00% de monóxido de carbono, 14,65% de hidrogénio, 45,81% de dióxido de carbono e 5,41% de metano. A simulação permitiu-nos ainda dimensionar o gasificador e determinar alguns parâmetros hidrodinâmicos do gasificador, considerando que a reação “water-gas shift” era a limitante, e que se pretendia obter uma conversão de 95%. A velocidade de operação do gasificador foi de 4,7m/s e a sua altura igual a 0,73m, para um diâmetro de 0,20m.

On the development of a test-bed application for the ART-WiSe architecture

The ART-WiSe (Architecture for Real-Time communications in Wireless Sensor Networks) framework aims at the design of new communication architectures and mechanisms for time-sensitive Wireless Sensor Networks (WSNs). We adopted a two-tiered architecture where an overlay Wireless Local Area Network (Tier 2) serves as a backbone for a WSN (Tier 1), relying on existing standard communication protocols and commercial-off-the-shell (COTS) technologies – IEEE 802.15.4/ZigBee for Tier 1 and IEEE 802.11 for Tier 2. In this line, a test-bed application is being developed for assessing, validating and demonstrating the ART-WiSe architecture. A pursuit-evasion application was chosen since it fulfils a number of requirements, namely it is feasible and appealing and imposes some stress to the architecture in terms of timeliness. To develop the testbed based on the previously referred technologies, an implementation of the IEEE 8021.5.4/ZigBee protocols is being carried out, since there is no open source available to the community. This paper highlights some relevant aspects of the ART-WiSe architecture, provides some intuition on the protocol stack implementation and presents a general view over the envisaged test-bed application.

On a test-bed application for the ART-WiSe framework

This report describes the development of a Test-bed Application for the ART-WiSe Framework with the aim of providing a means of access, validate and demonstrate that architecture. The chosen application is a kind of pursuit-evasion game where a remote controlled robot, navigating through an area covered by wireless sensor network (WSN), is detected and continuously tracked by the WSN. Then a centralized control station takes the appropriate actions for a pursuit robot to chase and “capture” the intruder one. This kind of application imposes stringent timing requirements to the underlying communication infrastructure. It also involves interesting research problems in WSNs like tracking, localization, cooperation between nodes, energy concerns and mobility. Additionally, it can be easily ported into a real-world application. Surveillance or search and rescue operations are two examples where this kind of functionality can be applied. This is still a first approach on the test-bed application and this development effort will be continuously pushed forward until all the envisaged objectives for the Art-WiSe architecture become accomplished.

Destruction of the tar present in syngas by combustion in porous media

The cleaning of syngas is one of the most important challenges in the development of technologies based on gasification of biomass. Tar is an undesired byproduct because, once condensed, it can cause fouling and plugging and damage the downstream equipment. Thermochemical methods for tar destruction, which include catalytic cracking and thermal cracking, are intrinsically attractive because they are energetically efficient and no movable parts are required nor byproducts are produced. The main difficulty with these methods is the tendency for tar to polymerize at high temperatures. An alternative to tar removal is the complete combustion of the syngas in a porous burner directly as it leaves the particle capture system. In this context, the main aim of this study is to evaluate the destruction of the tar present in the syngas from biomass gasification by combustion in porous media. A gas mixture was used to emulate the syngas, which included toluene as a tar surrogate. Initially, CHEMKIN was used to assess the potential of the proposed solution. The calculations revealed the complete destruction of the tar surrogate for a wide range of operating conditions and indicated that the most important reactions in the toluene conversion are C6H5CH3 + OH <-> C6H5CH2 + H2O, C6H5CH3 + OH <-> C6H4CH3 + H2O, and C6H5CH3 + O <-> OC6H4CH3 + H and that the formation of toluene can occur through C6H5CH2 + H <-> C6H5CH3. Subsequently, experimental tests were performed in a porous burner fired with pure methane and syngas for two equivalence ratios and three flow velocities. In these tests, the toluene concentration in the syngas varied from 50 to 200 g/Nm(3). In line with the CHEMKIN calculations, the results revealed that toluene was almost completely destroyed for all tested conditions and that the process did not affect the performance of the porous burner regarding the emissions of CO, hydrocarbons, and NOx.

Experimental dam-break waves profile analysis: horizontal mobile bed

River Flow, Vol. 2

Maximum level and time to peak of dam-break waves on mobile horizontal bed

Journal of Hydraulic Engineering, Vol. 135, No. 11, November 1, 2009

Multi-Agent Based Smart Grid Management and Simulation: Situation Awareness and Learning in a Test Bed with Simulated and Real Installations and Players

The rising usage of distributed energy resources has been creating several problems in power systems operation. Virtual Power Players arise as a solution for the management of such resources. Additionally, approaching the main network as a series of subsystems gives birth to the concepts of smart grid and micro grid. Simulation, particularly based on multi-agent technology is suitable to model all these new and evolving concepts. MASGriP (Multi-Agent Smart Grid simulation Platform) is a system that was developed to allow deep studies of the mentioned concepts. This paper focuses on a laboratorial test bed which represents a house managed by a MASGriP player. This player is able to control a real installation, responding to requests sent by the system operators and reacting to observed events depending on the context.

Modelação numérica de uma caldeira doméstica a pellets

A biomassa é uma das fontes de energia renovável com maior potencial em Portugal, sendo a capacidade de produção de pellets de biomassa atualmente instalada superior a 1 milhão de toneladas/ano. Contudo, a maioria desta produção destina-se à exportação ou à utilização em centrais térmicas a biomassa, cujo crescimento tem sido significativo nos últimos anos, prevendo-se que a capacidade instalada em 2020 seja de aproximadamente 250 MW. O mercado português de caldeiras a pellets é bastante diversificado. O estudo que realizamos permitiu concluir que cerca de 90% das caldeiras existentes no mercado português têm potências inferiores a 60 kW, possuindo na sua maioria grelha fixa (81%), com sistema de ignição eléctrica (92%) e alimentação superior do biocombustível sólido (94%). O objetivo do presente trabalho foi o desenvolvimento de um modelo para simulação de uma caldeira a pellets de biomassa, que para além de permitir otimizar o projeto e operação deste tipo de equipamento, permitisse avaliar as inovações tecnológicas nesta área. Para tal recorreu-se o BiomassGasificationFoam, um código recentemente publicado, e escrito para utilização com o OpenFOAM, uma ferramenta computacional de acesso livre, que permite a simulação dos processos de pirólise, gasificação e combustão de biomassa. Este código, que foi inicialmente desenvolvido para descrever o processo de gasificação na análise termogravimétrica de biomassa, foi por nós adaptado para considerar as reações de combustão em fase gasosa dos gases libertados durante a pirólise da biomassa (recorrendo para tal ao solver reactingFoam), e ter a possibilidade de realizar a ignição da biomassa, o que foi conseguido através de uma adaptação do código de ignição do XiFoam. O esquema de ignição da biomassa não se revelou adequado, pois verificou-se que a combustão parava sempre que a ignição era inativada, independentemente do tempo que ela estivesse ativa. Como alternativa, usaram-se outros dois esquemas para a combustão da biomassa: uma corrente de ar quente, e uma resistência de aquecimento. Ambos os esquemas funcionaram, mas nunca foi possível fazer com que a combustão fosse autossustentável. A análise dos resultados obtidos permitiu concluir que a extensão das reações de pirólise e de gasificação, que são ambas endotérmicas, é muito pequena, pelo que a quantidade de gases libertados é igualmente muito pequena, não sendo suficiente para libertar a energia necessária à combustão completa da biomassa de uma maneira sustentável. Para tentar ultrapassar esta dificuldade foram testadas várias alternativas, , que incluíram o uso de diferentes composições de biomassa, diferentes cinéticas, calores de reação, parâmetros de transferência de calor, velocidades do ar de alimentação, esquemas de resolução numérica do sistema de equações diferenciais, e diferentes parâmetros dos esquemas de resolução utilizados. Todas estas tentativas se revelaram infrutíferas. Este estudo permitiu concluir que o solver BiomassGasificationFoam, que foi desenvolvido para descrever o processo de gasificação de biomassa em meio inerte, e em que a biomassa é aquecida através de calor fornecido pelas paredes do reator, aparentemente não é adequado à descrição do processo de combustão da biomassa, em que a combustão deve ser autossustentável, e em que as reações de combustão em fase gasosa são importantes. Assim, é necessário um estudo mais aprofundado que permita adaptar este código à simulação do processo de combustão de sólidos porosos em leito fixo.

Aeromonas spp. isolated from oysters (Crassostrea rhizophorea) from a natural oyster bed, Ceará, Brazil

Between April and October 2002, thirty fortnightly collections of oysters (Crassostrea rhizophorea) from a natural oyster bed at the Cocó River estuary in the Sabiaguaba region (Fortaleza, Ceará, Brazil) were carried out, aiming to isolate Aeromonas spp. strains. Oyster samples were submitted to the direct plating (DP) and the presence/absence (P/A) methods. Aeromonas were identified in 15 (50%) samples analyzed by the DP method and in 13 (43%) analyzed by the P/A method. A. caviae, A. eucrenophila, A. media, A. sobria, A. trota, A. veronii bv. sobria, A. veronii bv. veronii and Aeromonas sp. were isolated. The predominant species was A. veronii (both biovars), which was identified in 13 (43%) samples, followed by A. media in 11 (37%) and A. caviae in seven (23%). From the 59 strains identified, 28 (48%) presented resistance to at least one of the eight antibiotics tested.

INSECTICIDE-TREATED BED NETS IN RONDÔNIA, BRAZIL: EVALUATION OF THEIR IMPACT ON MALARIA CONTROL

Mosquito nets treated with long-lasting insecticide (LLINs), when used in compliance with guidelines of the World Health Organization, may be effective for malaria vector control. In 2012, approximately 150,000 LLINs were installed in nine municipalities in the state of Rondônia. However, no studies have assessed their impact on the reduction of malaria incidence. This study analyzed secondary data of malaria incidence, in order to assess the impact of LLINs on the annual parasite incidence (API). The results showed no statistically significant differences in API one year after LLIN installation when compared to municipalities without LLINs. The adoption of measures for malaria vector control should be associated with epidemiological studies and evaluations of their use and efficiency, with the aim of offering convincing advantages that justify their implementation and limit malaria infection in the Amazon Region.

Acidogenic digestion of effluents of the cheese industry in packed bed biofilm reactors

Dissertation for the Master degree in Biotechnology

Study on the valorization routes of ashes from thermoelectric power plants working under mono-and co-combustion regimes

Thesis submitted to obtain the Doctoral degree in Energy and Bioenergy

Coherent structures in open channel flows with bed load transport over an hydraulically rough bed

Dissertação para obtenção do Grau de Mestre em Engenharia Civil – Perfil de Estruturas

Optimal design and operation of compact simulated moving bed processes for enantioseparations

Simulated moving bed (SMB) chromatography is attracting more and more attention since it is a powerful technique for complex separation tasks. Nowadays, more than 60% of preparative SMB units are installed in the pharmaceutical and in the food in- dustry [SDI, Preparative and Process Liquid Chromatography: The Future of Process Separations, International Strategic Directions, Los Angeles, USA, 2002. http://www. strategicdirections.com]. Chromatography is the method of choice in these ¯elds, be- cause often pharmaceuticals and ¯ne-chemicals have physico-chemical properties which di®er little from those of the by-products, and they may be thermally instable. In these cases, standard separation techniques as distillation and extraction are not applicable. The noteworthiness of preparative chromatography, particulary SMB process, as a sep- aration and puri¯cation process in the above mentioned industries has been increasing, due to its °exibility, energy e±ciency and higher product purity performance. Consequently, a new SMB paradigm is requested by the large number of potential small- scale applications of the SMB technology, which exploits the °exibility and versatility of the technology. In this new SMB paradigm, a number of possibilities for improving SMB performance through variation of parameters during a switching interval, are pushing the trend toward the use of units with smaller number of columns because less stationary phase is used and the setup is more economical. This is especially important for the phar- maceutical industry, where SMBs are seen as multipurpose units that can be applied to di®erent separations in all stages of the drug-development cycle. In order to reduce the experimental e®ort and accordingly the coast associated with the development of separation processes, simulation models are intensively used. One impor- tant aspect in this context refers to the determination of the adsorption isotherms in SMB chromatography, where separations are usually carried out under strongly nonlinear conditions in order to achieve higher productivities. The accurate determination of the competitive adsorption equilibrium of the enantiomeric species is thus of fundamental importance to allow computer-assisted optimization or process scale-up. Two major SMB operating problems are apparent at production scale: the assessment of product quality and the maintenance of long-term stable and controlled operation. Constraints regarding product purity, dictated by pharmaceutical and food regulatory organizations, have drastically increased the demand for product quality control. The strict imposed regulations are increasing the need for developing optically pure drugs.(...)