Preventing Cracking at Diaphragm/Plate Girder Connections in Steel Bridges, HR-393, 1998

Some of the Iowa Department of Transportation (Iowa DOT) continuous, steel, welded plate girder bridges have developed web cracking in the negative moment regions at the diaphragm connection plates. The cracks are due to out-of-plane bending of the web near the top flange of the girder. The out-of-plane bending occurs in the "web-gap", which is the portion of the girder web between (1) the top of the fillet welds attaching the diaphragm connection plate to the web and (2) the fillet welds attaching the flange to the web. A literature search indicated that four retrofit techniques have been suggested by other researchers to prevent or control this type of cracking. To eliminate the problem in new bridges, AASHTO specifications require a positive attachment between the connection plate and the top (tension) flange. Applying this requirement to existing bridges is expensive and difficult. The Iowa DOT has relied primarily on the hole-drilling technique to prevent crack extension once cracking has occurred; however, the literature indicates that hole-drilling alone may not be entirely effective in preventing crack extension. The objective of this research was to investigate experimentally a method proposed by the Iowa DOT to prevent cracking at the diaphragm/plate girder connection in steel bridges with X-type or K-type diaphragms. The method consists of loosening the bolts at some connections between the diaphragm diagonals and the connection plates. The investigation included selecting and testing five bridges: three with X-type diaphragms and two with K-type diaphragms. During 1996 and 1997, these bridges were instrumented using strain gages and displacement transducers to obtain the response at various locations before and after implementing the method. Bridges were subjected to loaded test trucks traveling in different lanes with speeds varying from crawl speed to 65 mph (104 km/h) to determine the effectiveness of the proposed method. The results of the study show that the effect of out-of-plane loading was confined to widths of approximately 4 in. (100 mm) on either side of the connection plates. Further, they demonstrate that the stresses in gaps with drilled holes were higher than those in gaps without cracks, implying that the drilling hole technique is not sufficient to prevent crack extension. The behavior of the web gaps in X-type diaphragm bridges was greatly enhanced by the proposed method as the stress range and out-of-plane distortion were reduced by at least 42% at the exterior girders. For bridges with K-type diaphragms, a similar trend was obtained. However, the stress range increased in one of the web gaps after implementing the proposed method. Other design aspects (wind, stability of compression flange, and lateral distribution of loads) must be considered when deciding whether to adopt the proposed method. Considering the results of this investigation, the proposed method can be implemented for X-type diaphragm bridges. Further research is recommended for K-type diaphragm bridges.

Retrofit Methods for Distortion Cracking Problems in Plate Girder Bridges, TR-436, 2003

This report is formatted to independently present four individual investigations related to similar web gap fatigue problems. Multiple steel girder bridges commonly exhibit fatigue cracking due to out-of-plane displacement of the web near the diaphragm connections. This fatigue-prone web gap area is typically located in negative moment regions of the girders where the diaphragm stiffener is not attached to the top flange. In the past, the Iowa Department of Transportation has attempted to stop fatigue crack propagation in these steel girder bridges by drilling holes at the crack tips. Other nondestructive retrofits have been tried; in a particular case on a two-girder bridge with floor beams, angles were bolted between the stiffener and top flange. The bolted angle retrofit has failed in the past and may not be a viable solution for diaphragm bridges. The drilled hole retrofit is often only a temporary solution, so a more permanent and effective retrofit is required. A new field retrofit has been developed that involves loosening the bolts in the connection between the diaphragm and the girders. Research on the retrofit has been initiated; however, no long-term studies of the effects of bolt loosening have been performed. The intent of this research is to study the short-term effects of the bolt loosening retrofit on I-beam and channel diaphragm bridges. The research also addressed the development of a continuous remote monitoring system to investigate the bolt loosening retrofit on an X-type diaphragm bridge over a number of months, ensuring that the measured strain and displacement reductions are not affected by time and continuous traffic loading on the bridge. The testing for the first three investigations is based on instrumentation of web gaps in a negative moment region on Iowa Department of Transportation bridges with I-beam, channel, and X-type diaphragms. One bridge of each type was instrumented with strain gages and deflection transducers. Field tests, using loaded trucks of known weight and configuration, were conducted on the bridges with the bolts in the tight condition and after implementing the bolt loosening retrofit to measure the effects of loosening the diaphragm bolts. Long-term data were also collected on the X-diaphragm bridge by a data acquisition system that collected the data continuously under ambient truck loading. The collected data were retrievable by an off-site modem connection to the remote data acquisition system. The data collection features and ruggedness of this system for remote bridge monitoring make it viable as a pilot system for future monitoring projects in Iowa. Results indicate that loosening the diaphragm bolts reduces strain and out-of-plane displacement in the web gap, and that the reduction is not affected over time by traffic or environmental loading on the bridge. Reducing the strain in the web gap allows the bridge to support more cycles of loading before experiencing fatigue, thus increase the service life of the bridge. Two-girder floor beam bridges may also exhibit fatigue cracking in girder webs.

High-throughput and sensitive quantitation of plasma catecholamines by ultraperformance liquid chromatography-tandem mass spectrometry using a solid phase microwell extraction plate.

Plasma catecholamines provide a reliable biomarker of sympathetic activity. The low circulating concentrations of catecholamines and analytical interferences require tedious sample preparation and long chromatographic runs to ensure their accurate quantification by HPLC with electrochemical detection. Published or commercially available methods relying on solid phase extraction technology lack sensitivity or require derivatization of catecholamine by hazardous reagents prior to tandem mass spectrometry (MS) analysis. Here, we manufactured a novel 96-well microplate device specifically designed to extract plasma catecholamines prior to their quantification by a new and highly sensitive ultraperformance liquid chromatography-tandem mass spectrometry (UPLC-MS/MS) method. Processing time, which included sample purification on activated aluminum oxide and elution, is less than 1 h per 96-well microplate. The UPLC-MS/MS analysis run time is 2.0 min per sample. This UPLC-MS/MS method does not require a derivatization step, reduces the turnaround time by 10-fold compared to conventional methods used for routine application, and allows catecholamine quantification in reduced plasma sample volumes (50-250 μL, e.g., from children and mice).

The birth of the Rheic Ocean - Early Palaeozoic subsidence patterns and subsequent tectonic plate scenarios

New plate-tectonic reconstructions of the Gondwana margin suggest that the location of Gondwana-derived terranes should not only be guided by the models, but should also consider the possible detrital input from some Asian blocks (Hunia), supposed to have been located along the Cambrian Gondwana margin, and accreted in the Silurian to the North-Chinese block. Consequently, the Gondwana margin has to be subdivided into a more western domain, where the future Avalonian blocks will be separated from Gondwana by the opening Rheic Ocean, whereas in its eastern continuation, hosting the future basement areas of Central Europe, different periods of crustal extension should be distinguished. Instead of applying a rather cylindrical model, it is supposed that crustal extension follows a much more complex pattern, where local back-arcs or intra-continental rifts are involved. Guided by the age data of magmatic rocks and the pattern of subsidence curves, the following extensional events can be distinguished: During the early to middle Cambrian, a back-arc setting guided the evolution at the Gondwana margin. Contemporaneous intra-continental rift basins developed at other places related to a general post-PanAfrican extensional phase affecting Africa Upper Cambrian formation of oceanic crust is manifested in the Chamrousse area, and may have lateral cryptic relics preserved in other places. This is regarded as the oceanisation of some marginal basins in a context of back-arc rifting. These basins were closed in a mid-Ordovician tectonic phase, related to the subduction of buoyant material (mid-ocean ridge?) Since the Early Ordovician, a new phase of extension is observed, accompanied by a large-scale volcanic activity, erosion of the rift shoulders generated detritus (Armorican Quartzite) and the rift basins collected detrital zircons from a wide hinterland. This phase heralded the opening of Palaeotethys, but it failed due to the Silurian collision (Eo-Variscan phase) of an intra-oceanic arc with the Gondwana margin. During this time period, at the eastern wing of the Gondwana margin begins the drift of the future Hunia microcontinents, through the opening of an eastern prolongation of the already existing Rheic Ocean. The passive margin of the remaining Gondwana was composed of the Galatian superterranes, constituents of the future Variscan basement areas. Remaining under the influence of crustal extension, they will start their drift to Laurussia since the earliest Devonian during the opening of the Palaeotethys Ocean. (C) 2008 Elsevier B.V. All rights reserved.

Pin guidance of reconstruction plate contour: an expanded role of external fixation

This article presents a modification of intraoperative external fixation for mandibular reconstruction with free tissue flaps. This technique is indicated when preregistration of the reconstruction plate is not possible due to transmandibular tumor extension. Once standard external fixation has been carried out and prior to segmental mandibulectomy, additional pins are fixed to the connecting rod that delineate the mandibular contour in three-dimensional (3D) space. Following mandibulectomy, these pins allow accurate contouring of the reconstruction plate and improved restoration of mandibular contour, projection, and dental occlusion. A step-by-step description of the technique using models and intraoperative photos is presented. This method of mandibular reconstruction is a simple and time-effective alternative to intraoperative computer navigation and 3D modeling in select cases of oral carcinoma where tumor infiltration of the outer mandibular cortex precludes prebending of the reconstruction plates.

High precision U/Pb zircon dating of the Chalten Plutonic Complex (Cerro Fitz Roy, Patagonia) and its relationship to arc migration in the southernmost Andes

We report new high-precision U/Pb ages and geochemical data from the Chalten Plutonic Complex to better understand the link between magmatism and tectonics in Southern Patagonia. This small intrusion located in the back-arc region east of the Patagonian Batholith provides important insights on the role of arc migration and subduction erosion. The Chalten Plutonic Complex consists of a suite of calc-alkaline gabbroic to granitic rocks, which were emplaced over 530 kyr between 16.90 +/- 0.05 Ma and 16.37 +/- 0.02 Ma. A synthesis of age and geochemical data from other intrusions in Patagonia reveals (a) striking similarities between the Chalten Plutonic Complex and the Neogene intrusions of the batholith and differences to other back-arc intrusions such as Torres del Paine (b) a distinct E-W trend of calc-alkaline magmatic activity between 20 and 17 Ma. We propose that this trend reflects the eastward migration of the magmatic arc, and the consistent age pattern between the subduction segments north and south of the Chile triple junction suggests a causal relation with a period of fast subduction of the Farallon-Nazca plate during the Early Miocene. Previously proposed flat slab models are not consistent with the present location and morphology of the Southern Patagonian Batholith. We advocate, alternatively, that migration of the magmatic arc is caused by subduction erosion due to the increasing subduction velocities during the Early Miocene.

Sarabande / P.O. Ferroud, comp.. Airs de ballet de "Platée" : choix / J.P. Rameau, comp. ; orchestre de la Société des grands concerts de Lyon ; G. M. Witkowski, dir.

Comprend : Sarabande ; Airs de ballet de Platée

Four-corner bone arthrodesis with dorsal rectangular plate: series and personal technique.

Controversy exists about the best method to achieve bone fusion in four-corner arthrodesis. Thirty-five patients who underwent this procedure by our technique were included in the study. Surgical indications were stage II-III SLAC wrist, stage II SNAC wrist and severe traumatic midcarpal joint injury. Mean follow-up was 4.6 years. Mean active flexion and extension were 34 degrees and 30 degrees respectively; grip strength recovery was 79%. Radiological consolidation was achieved in all cases. The mean DASH score was 23 and the postoperative pain improvement by visual analogue scale was statistically significant. Return to work was possible at 4 months for the average patient. Complications were a capitate fracture in one patient and the need for hardware removal in four cases. Four-corner bone wrist arthrodesis by dorsal rectangular plating achieves an acceptable preservation of range of motion with good pain relief, an excellent consolidation rate and minimal complications.

GIS and geodatabases application to global scale plate tectonics modelling

Les reconstructions palinspastiques fournissent le cadre idéal à de nombreuses études géologiques, géographiques, océanographique ou climatiques. En tant qu?historiens de la terre, les "reconstructeurs" essayent d?en déchiffrer le passé. Depuis qu?ils savent que les continents bougent, les géologues essayent de retracer leur évolution à travers les âges. Si l?idée originale de Wegener était révolutionnaire au début du siècle passé, nous savons depuis le début des années « soixante » que les continents ne "dérivent" pas sans but au milieu des océans mais sont inclus dans un sur-ensemble associant croûte « continentale » et « océanique »: les plaques tectoniques. Malheureusement, pour des raisons historiques aussi bien que techniques, cette idée ne reçoit toujours pas l'écho suffisant parmi la communauté des reconstructeurs. Néanmoins, nous sommes intimement convaincus qu?en appliquant certaines méthodes et certains principes il est possible d?échapper à l?approche "Wégenerienne" traditionnelle pour enfin tendre vers la tectonique des plaques. Le but principal du présent travail est d?exposer, avec tous les détails nécessaires, nos outils et méthodes. Partant des données paléomagnétiques et paléogéographiques classiquement utilisées pour les reconstructions, nous avons développé une nouvelle méthodologie replaçant les plaques tectoniques et leur cinématique au coeur du problème. En utilisant des assemblages continentaux (aussi appelés "assemblées clés") comme des points d?ancrage répartis sur toute la durée de notre étude (allant de l?Eocène jusqu?au Cambrien), nous développons des scénarios géodynamiques permettant de passer de l?une à l?autre en allant du passé vers le présent. Entre deux étapes, les plaques lithosphériques sont peu à peu reconstruites en additionnant/ supprimant les matériels océaniques (symbolisés par des isochrones synthétiques) aux continents. Excepté lors des collisions, les plaques sont bougées comme des entités propres et rigides. A travers les âges, les seuls éléments évoluant sont les limites de plaques. Elles sont préservées aux cours du temps et suivent une évolution géodynamique consistante tout en formant toujours un réseau interconnecté à travers l?espace. Cette approche appelée "limites de plaques dynamiques" intègre de multiples facteurs parmi lesquels la flottabilité des plaques, les taux d'accrétions aux rides, les courbes de subsidence, les données stratigraphiques et paléobiogéographiques aussi bien que les évènements tectoniques et magmatiques majeurs. Cette méthode offre ainsi un bon contrôle sur la cinématique des plaques et fournit de sévères contraintes au modèle. Cette approche "multi-source" nécessite une organisation et une gestion des données efficaces. Avant le début de cette étude, les masses de données nécessaires était devenues un obstacle difficilement surmontable. Les SIG (Systèmes d?Information Géographiques) et les géo-databases sont des outils informatiques spécialement dédiés à la gestion, au stockage et à l?analyse des données spatialement référencées et de leurs attributs. Grâce au développement dans ArcGIS de la base de données PaleoDyn nous avons pu convertir cette masse de données discontinues en informations géodynamiques précieuses et facilement accessibles pour la création des reconstructions. Dans le même temps, grâce à des outils spécialement développés, nous avons, tout à la fois, facilité le travail de reconstruction (tâches automatisées) et amélioré le modèle en développant fortement le contrôle cinématique par la création de modèles de vitesses des plaques. Sur la base des 340 terranes nouvellement définis, nous avons ainsi développé un set de 35 reconstructions auxquelles est toujours associé un modèle de vitesse. Grâce à cet ensemble de données unique, nous pouvons maintenant aborder des problématiques majeurs de la géologie moderne telles que l?étude des variations du niveau marin et des changements climatiques. Nous avons commencé par aborder un autre problème majeur (et non définitivement élucidé!) de la tectonique moderne: les mécanismes contrôlant les mouvements des plaques. Nous avons pu observer que, tout au long de l?histoire de la terre, les pôles de rotation des plaques (décrivant les mouvements des plaques à la surface de la terre) tendent à se répartir le long d'une bande allant du Pacifique Nord au Nord de l'Amérique du Sud, l'Atlantique Central, l'Afrique du Nord, l'Asie Centrale jusqu'au Japon. Fondamentalement, cette répartition signifie que les plaques ont tendance à fuir ce plan médian. En l'absence d'un biais méthodologique que nous n'aurions pas identifié, nous avons interprété ce phénomène comme reflétant l'influence séculaire de la Lune sur le mouvement des plaques. La Lune sur le mouvement des plaques. Le domaine océanique est la clé de voute de notre modèle. Nous avons attaché un intérêt tout particulier à le reconstruire avec beaucoup de détails. Dans ce modèle, la croûte océanique est préservée d?une reconstruction à l?autre. Le matériel crustal y est symbolisé sous la forme d?isochrones synthétiques dont nous connaissons les âges. Nous avons également reconstruit les marges (actives ou passives), les rides médio-océaniques et les subductions intra-océaniques. En utilisant ce set de données très détaillé, nous avons pu développer des modèles bathymétriques 3-D unique offrant une précision bien supérieure aux précédents.<br/><br/>Palinspastic reconstructions offer an ideal framework for geological, geographical, oceanographic and climatology studies. As historians of the Earth, "reconstructers" try to decipher the past. Since they know that continents are moving, geologists a trying to retrieve the continents distributions through ages. If Wegener?s view of continent motions was revolutionary at the beginning of the 20th century, we know, since the Early 1960?s that continents are not drifting without goal in the oceanic realm but are included in a larger set including, all at once, the oceanic and the continental crust: the tectonic plates. Unfortunately, mainly due to technical and historical issues, this idea seems not to receive a sufficient echo among our particularly concerned community. However, we are intimately convinced that, by applying specific methods and principles we can escape the traditional "Wegenerian" point of view to, at last, reach real plate tectonics. This is the main aim of this study to defend this point of view by exposing, with all necessary details, our methods and tools. Starting with the paleomagnetic and paleogeographic data classically used in reconstruction studies, we developed a modern methodology placing the plates and their kinematics at the centre of the issue. Using assemblies of continents (referred as "key assemblies") as anchors distributed all along the scope of our study (ranging from Eocene time to Cambrian time) we develop geodynamic scenarios leading from one to the next, from the past to the present. In between, lithospheric plates are progressively reconstructed by adding/removing oceanic material (symbolized by synthetic isochrones) to major continents. Except during collisions, plates are moved as single rigid entities. The only evolving elements are the plate boundaries which are preserved and follow a consistent geodynamical evolution through time and form an interconnected network through space. This "dynamic plate boundaries" approach integrates plate buoyancy factors, oceans spreading rates, subsidence patterns, stratigraphic and paleobiogeographic data, as well as major tectonic and magmatic events. It offers a good control on plate kinematics and provides severe constraints for the model. This multi-sources approach requires an efficient data management. Prior to this study, the critical mass of necessary data became a sorely surmountable obstacle. GIS and geodatabases are modern informatics tools of specifically devoted to store, analyze and manage data and associated attributes spatially referenced on the Earth. By developing the PaleoDyn database in ArcGIS software we converted the mass of scattered data offered by the geological records into valuable geodynamical information easily accessible for reconstructions creation. In the same time, by programming specific tools we, all at once, facilitated the reconstruction work (tasks automation) and enhanced the model (by highly increasing the kinematic control of plate motions thanks to plate velocity models). Based on the 340 terranes properly defined, we developed a revised set of 35 reconstructions associated to their own velocity models. Using this unique dataset we are now able to tackle major issues of the geology (such as the global sea-level variations and climate changes). We started by studying one of the major unsolved issues of the modern plate tectonics: the driving mechanism of plate motions. We observed that, all along the Earth?s history, plates rotation poles (describing plate motions across the Earth?s surface) tend to follow a slight linear distribution along a band going from the Northern Pacific through Northern South-America, Central Atlantic, Northern Africa, Central Asia up to Japan. Basically, it sighifies that plates tend to escape this median plan. In the absence of a non-identified methodological bias, we interpreted it as the potential secular influence ot the Moon on plate motions. The oceanic realms are the cornerstone of our model and we attached a particular interest to reconstruct them with many details. In this model, the oceanic crust is preserved from one reconstruction to the next. The crustal material is symbolised by the synthetic isochrons from which we know the ages. We also reconstruct the margins (active or passive), ridges and intra-oceanic subductions. Using this detailed oceanic dataset, we developed unique 3-D bathymetric models offering a better precision than all the previously existing ones.

Treatment of type B periprosthetic femur fractures with curved non-locking plate with eccentric holes: Retrospective study of 43 patients with minimum 1-year follow-up.

INTRODUCTION: Periprosthetic femur fracture (PFF) is a serious complication after total hip arthroplasty that can be treated using different internal fixation devices. However, the outcomes with curved non-locking plates with eccentric holes in this indication have not been reported previously. The objectives of this study were to determine: (1) the union rate; (2) the complication rate; (3) autonomy in a group of patients with a Vancouver type B PFF who were treated with this plate. HYPOTHESIS: Use of this plate results in a high union rate with minimal mechanical complications. MATERIALS AND METHODS: Forty-three patients with a mean age of 79 years±13 (41-98) who had undergone fixation of Vancouver type B PFF with this plate between 2002 and 2007 were included in the study. The time to union and Parker Mobility Score were evaluated. The revision-free survival (all causes) was calculated using Kaplan-Meier analysis. The average follow-up was 42 months±20 (16-90). RESULTS: Union was obtained in all patients in a mean of 2.4 months±0.6 (2-4). One patient had varus malunion of the femur. The Parker Mobility Score decreased from 5.93±1.94 (2-9) to 4.93±1.8 (1-9) (P=0.01). Two patients required a surgical revision: one for an infection after 4.5 years and one for stem loosening. The survival of the femoral stem 5 years after fracture fixation was 83.3%±12.6%. CONCLUSION: Use of a curved plate with eccentric holes for treating type B PFF led to a high union rate and a low number of fixation-related complications. However, PFF remains a serious complication of hip arthroplasty that is accompanied by high morbidity and mortality rates. LEVEL OF EVIDENCE: Retrospective study, level IV.

Integrin-Specific Mechanoresponses to Compression and Extension Probed by Cylindrical Flat-Ended AFM Tips in Lung Cells

Cells from lung and other tissues are subjected to forces of opposing directions that are largely transmitted through integrin-mediated adhesions. How cells respond to force bidirectionality remains ill defined. To address this question, we nanofabricated flat-ended cylindrical Atomic Force Microscopy (AFM) tips with ~1 µm2 cross-section area. Tips were uncoated or coated with either integrin-specific (RGD) or non-specific (RGE/BSA) molecules, brought into contact with lung epithelial cells or fibroblasts for 30 s to form focal adhesion precursors, and used to probe cell resistance to deformation in compression and extension. We found that cell resistance to compression was globally higher than to extension regardless of the tip coating. In contrast, both tip-cell adhesion strength and resistance to compression and extension were the highest when probed at integrin-specific adhesions. These integrin-specific mechanoresponses required an intact actin cytoskeleton, and were dependent on tyrosine phosphatases and Ca2+ signaling. Cell asymmetric mechanoresponse to compression and extension remained after 5 minutes of tip-cell adhesion, revealing that asymmetric resistance to force directionality is an intrinsic property of lung cells, as in most soft tissues. Our findings provide new insights on how lung cells probe the mechanochemical properties of the microenvironment, an important process for migration, repair and tissue homeostasis.