Estudo tribológico de biolubrificantes com adição de nanopartículas de óxidos (zinco e cobre)

Currently, vegetable oils have been studied for bio-lubricants base that fits the new environmental standards. Since, in a world full of finite natural resources, mineral oils bring consequences to the environment due to its low biodegradability and toxicity, also it is important to consider that synthetic oils have a high cost The aim of this work is to obtain a biolubricant additived with oxide nanoparticles (ZnO and CuO) for better resistance to friction and wear, which is not toxic to the environment and have better adherence under boundary lubrication. The methodology consisted in the synthesis of bio-lubricants (soybean and sunflower base) by epoxidation reaction. Then, some physical-chemical analysis in bio-lubricants are made to characterize theses lubricants, such as, density, acidity, iodine value, viscosity, viscosity index. Later, the lubricants were additive with nanoparticles. The tribological performance was evaluated by the equipment HFRR (High Frequency Reciprocating Rig) consisting of a wear test ball-plan type. The characterization of wear analysis was performed by SEM / EDS. The results show that bio-lubricants may be synthesized by reaction of epoxidation with good conversion. Tribological point of view, the epoxidized oils are more effective than lubricant additived with the oxide nanoparticles, they had lower coefficients of friction and better rate of film formation in the study. However, because they are environmentally friendly, bio-lubricants gain the relevant importance in tribological field

Use of scrap tire rubber in place of SBS in modified asphalt as an environmentally correct alternative for Brazil

Reusing scrap tires has become a worldwide challenge, especially due to the great difficulty in finding ecologically and economically feasible ways to dispose of them. This has led to the creation of specific programs and legislation for reusing scrap tires. Research has shown that a certain percentage of scrap tire rubber can be added to asphalt compositions, and this has become a worldwide practice. This paper describes the properties of four asphalt compositions modified with scrap tire rubber (STR) prepared in the laboratory. These properties are then compared with those of asphalt modified with styrene butadiene styrene (SBS), a synthetic polymer and one of the most common modifiers, to verify the feasibility of using scrap tire rubber as a substitute for SBS. The scope of this study does not include an analysis of how STR affects end-of-life asphalt. The main findings indicate that STR is a potential substitute of SBS in paving material, and although it does not meet some of the standard specifications when compared with SBS, these issues can be overcome by proper care during storage and transportation. The substitution of SBS by STR also showed the potential for about 10% in expenditure savings. (C) 2012 Elsevier Ltd. All rights reserved.

Analysis of surface integrity for minimum quantity lubricant - MQL in grinding

The quality of machined components is currently of high interest, for the market demands mechanical components of increasingly high performance, not only from the standpoint of functionality but also from that of safety. Components produced through operations involving the removal of material display surface irregularities resulting not only from the action of the tool itself, but also from other factors that contribute to their superficial texture. This texture can exert a decisive influence on the application and performance of the machined component. This article analyzes the behavior of the minimum quantity lubricant (MQL) technique and compares it with the conventional cooling method. To this end, an optimized fluid application method was devised using a specially designed nozzle, by the authors, through which a minimum amount of oil is sprayed in a compressed air flow, thus meeting environmental requirements. This paper, therefore, explores and discusses the concept of the MQL in the grinding process. The performance of the MQL technique in the grinding process was evaluated based on an analysis of the surface integrity (roughness, residual stress, microstructure and microhardness). The results presented here are expected to lead to technological and ecological gains in the grinding process using MQL. (c) 2006 Elsevier Ltd. All rights reserved.

Limpeza da superfície de corte de rebolos por um sistema de ar comprimido na retificação cilíndrica externa de mergulho de materiais cerâmicos refrigerados com a técnica da mínima quantidade de lubrificante (MQL)

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Identification of lubricant contamination by biodiesel using vibration analysis and neural network

Purpose - The purpose of this paper is to provide information on lubricant contamination by biodiesel using vibration and neural network.Design/methodology/approach - The possible contamination of lubricants is verified by analyzing the vibration and neural network of a bench test under determinated conditions.Findings - Results have shown that classical signal analysis methods could not reveal any correlation between the signal and the presence of contamination, or contamination grade. on other hand, the use of probabilistic neural network (PNN) was very successful in the identification and classification of contamination and its grade.Research limitations/implications - This study was done for some specific kinds of biodiesel. Other types of biodiesel could be analyzed.Practical implications Contamination information is presented in the vibration signal, even if it is not evident by classical vibration analysis. In addition, the use of PNN gives a relatively simple and easy-to-use detection tool with good confidence. The training process is fast, and allows implementation of an adaptive training algorithm.Originality/value - This research could be extended to an internal combustion engine in order to verify a possible contamination by biodiesel.

A rapid, environmentally friendly, and reliable method for pesticide analysis in high-fat samples

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Exposure to rabies virus in a population of free-ranging capuchin monkeys (Cebus apella nigritus) in a fragmented, environmentally protected area in southeastern Brazil

The aim of this study is to assess the frequency of rabies antibodies in free-ranging capuchin monkeys (Cebus apella nigritus) in a fragmented, environmentally protected, rural area of southeastern Brazil. Thirty-six free-ranging monkeys were tested by the rapid fluorescent focus inhibition test for detection of antibodies against rabies virus. Four individuals (11.11 %) had neutralizing antibody titers a parts per thousand yen0.25 IU/mL, demonstrating rabies virus exposure.

Surface morphology of Diplodon expansus (Kuster, 1856; Mollusca, Bivalvia, Hyriidae) gill filaments after exposure to environmentally relevant concentrations of atrazine herbicide

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Biodegradation and toxicological evaluation of lubricant oils

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Toxicity and Biodegradation in Sandy Soil Contaminated by Lubricant Oils

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Applied models to biodegradation kinetics of lubricant and vegetable oils in wastewater

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Adapted Physical Education teachers and teaching knowledge

In the 1980's, there was a suggestion of including the Adapted Physical Education discipline in the Physical Education Graduation Course. In this perspective, starting from the Adapted Physical Education teacher's routine, the aim of this research was to verify what these teachers know and how they manage to plan, elaborate and apply their knowledge with their students with educational special needs. It's an exploring study that had in its interview and silabus analisis technics the source of its data. Among its most important results, it showed teaching, experimental and pedagogical knowledge as part of Physical Education and Adapted Physical Education, in the arrangement, building and knowledge apliance.

Domestic microwave oven adapted for fast heat treatment of Ba0.5Sr0.5(Ti0.8Sn0.2)O-3 powders

In this work, BSTSn powders prepared by the polymeric precursor method were heat treated in a domestic microwave oven (MW) using a SiC susceptor to absorb the microwave energy and transfer the heat to the powder. The main advantage of MW is to reduce the thermal treatment time for phase crystallization. The powders were heat treated at 300 degrees C for 20 h in conventional oven, 300 degrees C for 10 min, 20 min, and 30 min in MW and at 500 degrees C for 1 min in MW. After thermal treatment, the photoluminescent properties of powders at room temperature were analyzed. (c) 2007 Published by Elsevier B.V.