Particle emission factors during cooking activities

Exposure to particles emitted by cooking activities may be responsible for a variety of respiratory health effects. However, the relationship between these exposures and their subsequent effects on health cannot be evaluated without understanding the properties of the emitted aerosol or the main parameters that influence particle emissions during cooking. Whilst traffic-related emissions, stack emissions and ultrafine particle concentrations (UFP, diameter < 100 nm) in urban ambient air have been widely investigated for many years, indoor exposure to UFPs is a relatively new field and in order to evaluate indoor UFP emissions accurately, it is vital to improve scientific understanding of the main parameters that influence particle number, surface area and mass emissions. The main purpose of this study was to characterise the particle emissions produced during grilling and frying as a function of the food, source, cooking temperature and type of oil. Emission factors, along with particle number concentrations and size distributions were determined in the size range 0.006-20 m using a Scanning Mobility Particle Sizer (SMPS) and an Aerodynamic Particle Sizer (APS). An infrared camera was used to measure the temperature field. Overall, increased emission factors were observed to be a function of increased cooking temperatures. Cooking fatty foods also produced higher particle emission factors than vegetables, mainly in terms of mass concentration, and particle emission factors also varied significantly according to the type of oil used.

An investigation into how work-related road safety can be enhanced

Despite the facts that vehicle incidents continue to be the most common mechanism for Australian compensated fatalities and that employers have statutory obligations to provide safe workplaces, very few organisations are proactively and comprehensively managing their work-related road risks. Unfortunately, limited guidance is provided in the existing literature to assist practitioners in managing work-related road risks. The current research addresses this gap in the literature. To explore how work-related road safety can be enhanced, three studies were conducted. Study one explored the effectiveness of a range of risk management initiatives and whether comprehensive risk management practices were associated with safety outcomes. Study two explored barriers to, and facilitators for, accepting risk management initiatives. Study three explored the influence of organisational factors on road safety outcomes to identify optimal work environments for managing road risks. To maximise the research sample and increase generalisability, the studies were designed to allow data collection to be conducted simultaneously drawing upon the same sample obtained from four Australian organisations. Data was collected via four methods. A structured document review of published articles was conducted to identify what outcomes have been observed in previously investigated work-related road safety initiatives. The documents reviewed collectively assessed the effectiveness of 19 work-related road safety initiatives. Audits of organisational practices and process operating within the four researched organisations were conducted to identify whether organisations with comprehensive work-related road risk management practices and processes have better safety outcomes than organisations with limited risk management practices and processes. Interviews were conducted with a sample of 24 participants, comprising 16 employees and eight managers. The interviews were conducted to identify what barriers and facilitators within organisations are involved in implementing work-related road safety initiatives and whether differences in fleet safety climate, stage of change and safety ownership relate to work-related road safety outcomes. Finally, questionnaires were administered to a sample of 679 participants. The questionnaires were conducted to identify which initiatives are perceived by employees to be effective in managing work-related road risks and whether differences in fleet safety climate, stage of change and safety ownership relate to work-related road safety outcomes. Seven research questions were addressed in the current research project. The key findings with respect to each of the research questions are presented below. Research question one: What outcomes have been observed in previously investigated work-related road safety initiatives? The structured document review indicated that initiatives found to be positively associated with occupational road safety both during and after the intervention period included: a pay rise; driver training; group discussions; enlisting employees as community road safety change agents; safety reminders; and group and individual rewards. Research question two: Which initiatives are perceived by employees to be effective in managing work-related road risks? Questionnaire findings revealed that employees believed occupational road risks could best be managed through making vehicle safety features standard, providing practical driver skills training and through investigating serious vehicle incidents. In comparison, employees believed initiatives including signing a promise card commitment to drive safely, advertising the organisation’s phone number on vehicles and consideration of driving competency in staff selection process would have limited effectiveness in managing occupational road safety. Research question three: Do organisations with comprehensive work-related road risk management practices and processes have better safety outcomes than organisations with limited risk management practices and processes? The audit identified a difference among the organisations in their management of work-related road risks. Comprehensive risk management practices were associated with employees engaging in overall safer driving behaviours, committing less driving errors, and experiencing less fatigue and distraction issues when driving. Given that only four organisations participated in this research, these findings should only be considered as preliminary. Further research should be conducted to explore the relationship between comprehensiveness of risk management practices and road safety outcomes with a larger sample of organisations. Research question four: What barriers and facilitators within organisations are involved in implementing work-related road safety initiatives? The interviews identified that employees perceived six organisational characteristics as potential barriers to implementing work-related road safety initiatives. These included: prioritisation of production over safety; complacency towards work-related road risks; insufficient resources; diversity; limited employee input in safety decisions; and a perception that road safety initiatives were an unnecessary burden. In comparison, employees perceived three organisational characteristics as potential facilitators to implementing work-related road safety initiatives. These included: management commitment; the presence of existing systems that could support the implementation of initiatives; and supportive relationships. Research question five: Do differences in fleet safety climate relate to work-related road safety outcomes? The interviews and questionnaires identified that organisational climates with high management commitment, support for managing work demands, appropriate safety rules and safety communication were associated with employees who engaged in safer driving behaviours. Regression analyses indicated that as participants’ perceptions of safety climate increased, the corresponding likelihood of them engaging in safer driving behaviours increased. Fleet safety climate was perceived to influence road safety outcomes through several avenues. Some of these included: the allocation of sufficient resources to manage occupational road risks; fostering a supportive environment of mutual responsibility; resolving safety issues openly and fairly; clearly communicating to employees that safety is the top priority; and developing appropriate work-related road safety policies and procedures. Research question six: Do differences in stage of change relate to work-related road safety outcomes? The interviews and questionnaires identified that participants’ perceptions of initiative effectiveness were found to vary with respect to their individual stage of readiness, with stage-matched initiatives being perceived most effective. In regards to safety outcomes, regression analyses identified that as participants’ progress through the stages of change, the corresponding likelihood of them being involved in vehicle crashes decreases. Research question seven: Do differences in safety ownership relate to work-related road safety outcomes? The interviews and questionnaires revealed that management of road risks is often given less attention than other areas of health and safety management in organisations. In regards to safety outcomes, regression analyses identified that perceived authority and perceived shared ownership both emerged as significant independent predictors of self-reported driving behaviours pertaining to fatigue and distractions. The regression models indicated that as participants’ perceptions of the authority of the person managing road risks increases, and perceptions of shared ownership of safety tasks increases, the corresponding likelihood of them engaging in driving while fatigued or multitasking while driving decreases. Based on the findings from the current research, the author makes several recommendations to assist practitioners in developing proactive and comprehensive approaches to managing occupational road risks. The author also suggests several avenues for future research in the area of work-related road safety.

Structural health monitoring of bridges using acoustic emission technology

Bridges are an important part of society's infrastructure and reliable methods are necessary to monitor them and ensure their safety and efficiency. Bridges deteriorate with age and early detection of damage helps in prolonging the lives and prevent catastrophic failures. Most bridges still in used today were built decades ago and are now subjected to changes in load patterns, which can cause localized distress and if not corrected can result in bridge failure. In the past, monitoring of structures was usually done by means of visual inspection and tapping of the structures using a small hammer. Recent advancements of sensors and information technologies have resulted in new ways of monitoring the performance of structures. This paper briefly describes the current technologies used in bridge structures condition monitoring with its prime focus in the application of acoustic emission (AE) technology in the monitoring of bridge structures and its challenges.

Load sharing and power quality enhanced operation of a distributed microgrid

This paper describes control methods for proper load sharing between parallel converters connected in a microgrid and supplied by distributed generators (DGs). It is assumed that the microgrid spans a large area and it supplies loads in both in grid connected and islanded modes. A control strategy is proposed to improve power quality and proper load sharing in both islanded and grid connected modes. It is assumed that each of the DGs has a local load connected to it which can be unbalanced and/or nonlinear. The DGs compensate the effects of unbalance and nonlinearity of the local loads. Common loads are also connected to the microgrid, which are supplied by the utility grid under normal conditions. However during islanding, each of the DGs supplies its local load and shares the common load through droop characteristics. Both impedance and motor loads are considered to verify the system response. The efficacy of the controller has been validated through simulation for various operating conditions using PSCAD. It has been found through simulation that the total Harmonic Distortion (THD) of the of the microgrid voltage is about 10% and the negative and zero sequence component are around 20% of the positive sequence component before compensation. After compensation, the THD remain below 0.5%, whereas, negative and zero sequence components of the voltages remain below 0.02% of the positive sequence component.

Multi-output buck-boost converter with enhanced dynamic response to load and input voltage changes

This paper presents a new multi-output DC/DC converter topology that has step-up and step-down conversion capabilities. In this topology, several output voltages can be generated which can be used in different applications such as multilevel converters with diode-clamped topology or power supplies with several voltage levels. Steady state and dynamic equations of the proposed multi-output converter have been developed, that can be used for steady state and transient analysis. Two control techniques have been proposed for this topology based on constant and dynamic hysteresis band height control to address different applications. Simulations have been performed for different operating modes and load conditions to verify the proposed topology and its control technique. Additionally, a laboratory prototype is designed and implemented to verify the simulation results.

Psychosocial predictors of the use of enhanced podcasting in student learning

The current study examined the influence of psychosocial constructs, from a theory of planned behavior (TPB) perspective, to predict university students’ (N = 159) use of a newly offered on-line learning tool, enhanced podcasts. Pre-semester, students completed questionnaires assessing the TPB predictors (attitude, subjective norm, perceived behavioral control) related to intended enhanced podcast use until the middle of semester. Mid-semester, students completed similar items relating to podcast use until the end of semester. Self-report measures of podcast use were obtained at the middle and end of semester. At both time points, students’ attitudes predicted their intentions and, at the initial time point, subjective norm also predicted intended podcast use. An examination of the beliefs underlying attitudes, the only construct to predict intentions at both time points, revealed differences between those students higher, rather than lower on intentions to use the podcasts, especially for the perceived educational benefits of podcast use later in the semester. Intentions to use enhanced podcasting only predicted self-reported use in the second half of the semester. Overall, this study identified some of the determinants which should be considered by those aiming to encourage student use of novel on-line educational tools.

Investigation of mechanisms governing emission of odorants

The literature identifies several models that describe inter-phase mass transfer, key to the emission process. While the emission process is complex and these models may be more or less successful at predicting mass transfer rates, they identify three key variables for a system involving a liquid and an air phase in contact with it: • A concentration (or partial pressure) gradient driving force; • The fluid dynamic characteristics within the liquid and air phases, and • The chemical properties of the individual components within the system. In three applied research projects conducted prior to this study, samples collected with two well-known sampling devices resulted in very different odour emission rates. It was not possible to adequately explain the differences observed. It appeared likely, however, that the sample collection device might have artefact effects on the emission of odorants, i.e. the sampling device appeared to have altered the mass transfer process. This raised the obvious question: Where two different emission rates are reported for a single source (differing only in the selection of sampling device), and a credible explanation for the difference in emission rate cannot be provided, which emission rate is correct? This research project aimed to identify the factors that determine odour emission rates, the impact that the characteristics of a sampling device may exert on the key mass transfer variables, and ultimately, the impact of the sampling device on the emission rate itself. To meet these objectives, a series of targeted reviews, and laboratory and field investigations, were conducted. Two widely-used, representative devices were chosen to investigate the influence of various parameters on the emission process. These investigations provided insight into the odour emission process generally, and the influence of the sampling device specifically.

Bioactive inorganic materials/alginate composite microspheres with controllable drug-delivery ability

Alginate microspheres are considered a promising material as a drug carrier in bone repair due to excellent biocompatibility, but their main disadvantage is low drug entrapment efficiency and non-controllable release. The aim of this study was to investigate the effect of incorporating mesoporous bioglass (MBG), non-mesoporous bioglass (BG) or hydroxyapatite (HAp) into alginate microspheres on their drug-loading and release properties. X-ray diffraction (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), and atomic emission spectroscopy (AES) were used to analyse the composition, structure and dissolution of bioactive inorganic materials and their microspheres. Dexamethasone (DEX)-loading and release ability of four microspheres were tested in phosphate buffered saline with varying pHs. Results showed that the drug-loading capacity was enhanced with the incorporation of bioactive inorganic materials into alginate microspheres. The MBG/Alginate microspheres had the highest drug loading ability. DEX release from alginate microspheres correlated to the dissolution of MBG, BG and HAp in PBS, and that the pH was an efficient factor in controlling the DEX release; a high pH resulted in greater DEX release, whereas a low pH delayed DEX release. In addition, MBG/alginate, BG/alginate and HAp/alginate microspheres had varying apatite-formation and dissolution abilities, which indicate that the composites would behave differently with respect to bioactivity. The study suggests that microspheres made of a composite of bioactive inorganic materials and alginate have a bioactivity and degradation profile which greatly improves their drug delivery capacity, thus enhancing their potential applications as bioactive filler materials for bone tissue regeneration.

Enhancing transition : an enhanced model of clinical placement for final year nursing students

Specialised support for student nurses making the transition to graduate nurse can be crucial to successful and smooth adjustment, and can create a path to positive and stable career experiences. This paper describes an enhanced model of final year nursing student placements which was trialled in 2006 at the Queensland University of Technology. The model involved collaboration with two major urban health services and resources were developed to support effective transition experiences. Ninety-two students, including 29 trial participants and 63 non-trial participants were assessed on preparedness for professional practice, before and after the trial semester. Results indicated an increase in preparedness across the entire sample, but students participating in the trial did not differ significantly in overall preparedness change from those who did not participate. Higher baseline preparedness in the trial group highlighted the possibility that proactive students who choose enrichment experiences tend to be likelier to gain benefit from such options than those who do not. Qualitative findings from focus groups conducted with 12 transition group students highlighted that one of the main beneficial aspects of the experience for students was the sense of belonging to a team that understood their learning needs and could work constructively with them.

IT-enhanced communication protocols for building project management

Purpose – Building project management requires real time flow of information between all the project team members or the supply chain members. In the present scenario, when project participants are geographically separated, adoption of Information Communication Technology (ICT) enables such effective communication. But strategic adoption of ICT requires that all the supply chain members follow the accepted methods of communication or the communication protocols. The majority of the construction organizations are small and medium enterprises (SMEs). This research, therefore, proposes to focus on developing IT-enhanced communication protocols for building project management by SMEs. Design/methodology/approach – The research adopts a sequential mixed methods approach, where data collection and analysis are conducted in both the quantitative and qualitative phases of research. Findings – The protocols are proposed as a “Strategic Model for Enhancing ICT Diffusion in Building Projects”. The framework for the model is discussed at three levels of study, i.e industry, organization, and people. Practical implications – While the research was conducted in an Indian context, the research outcome is envisaged to be widely applicable in other countries with due considerations. Originality/value – The developed framework has implications for national level bodies and academic institutions, organizations, people or project managers and is applicable at the international level after due considerations.

Nitrogen fertilizer rate management as a nitrous oxide mitigation strategy: Development of a nitrous oxide emission reduction protocol (NERP)

Nitrous oxide (N2O) is a potent agricultural greenhouse gas (GHG). More than 50% of the global anthropogenic N2O flux is attributable to emissions from soil, primarily due to large fertilizer nitrogen (N) applications to corn and other non-leguminous crops. Quantification of the trade–offs between N2O emissions, fertilizer N rate, and crop yield is an essential requirement for informing management strategies aiming to reduce the agricultural sector GHG burden, without compromising productivity and producer livelihood. There is currently great interest in developing and implementing agricultural GHG reduction offset projects for inclusion within carbon offset markets. Nitrous oxide, with a global warming potential (GWP) of 298, is a major target for these endeavours due to the high payback associated with its emission prevention. In this paper we use robust quantitative relationships between fertilizer N rate and N2O emissions, along with a recently developed approach for determining economically profitable N rates for optimized crop yield, to propose a simple, transparent, and robust N2O emission reduction protocol (NERP) for generating agricultural GHG emission reduction credits. This NERP has the advantage of providing an economic and environmental incentive for producers and other stakeholders, necessary requirements in the implementation of agricultural offset projects.

Identification of acoustic emission wave modes for accurate source location in plate-like structures

Acoustic emission (AE) technique is a popular tool used for structural health monitoring of civil, mechanical and aerospace structures. It is a non-destructive method based on rapid release of energy within a material by crack initiation or growth in the form of stress waves. Recording of these waves by means of sensors and subsequent analysis of the recorded signals convey information about the nature of the source. Ability to locate the source of stress waves is an important advantage of AE technique; but as AE waves travel in various modes and may undergo mode conversions, understanding of the modes (‘modal analysis’) is often necessary in order to determine source location accurately. This paper presents results of experiments aimed at finding locations of artificial AE sources on a thin plate and identifying wave modes in the recorded signal waveforms. Different source locating techniques will be investigated and importance of wave mode identification will be explored.