Analytical Assessment of a Home Made Capillary Electrophoresis Equipment with Linear Charge Coupled Device for Visible Light Absorption Detection in the Determination of Food Dyes

The performance of modular home made capillary electrophoresis equipment with spectrophotometric detection, at a visible region by means of a miniaturized linear charge coupled device, was evaluated for the determination of four food dyes. This system presents a simple but efficient home made cell detection scheme. A computer program that converts the spectral data after each run into the electropherograms was developed to evaluate the analytical parameters. The dyes selected for analytical evaluation of the system were Brilliant Blue FCF, Fast Green FCF, Sunset Yellow FCF, and Amaranth. Separation was carried out in a 29cm length and 75 mu m I.D fused silica capillary, using 10mmolL-1 borate buffer at pH 9, with separation voltage of 7.5kV. The detection limits for the dyes were between 0.3 and 1.5mgL-1 and the method presented adequate linearity over the ranges studied, with correlation coefficients greater than 0.99. The method was applied for determination and quantification of these dyes in fruit juices and candies.

Comparison of the analytical performance of electrophoresis microchannels fabricated in PDMS, glass, and polyester-toner

This paper compares the analytical performance of microchannels fabricated in PDMS, glass, and polyester-toner for electrophoretic separations. Glass and PDMS chips were fabricated using well-established photolithographic and replica-molding procedures, respectively. PDMS channels were sealed against three different types of materials: native PDMS, plasma-oxidized PDMS, and glass. Polyester-toner chips were micromachined by a direct-printing process using an office laser printer. All microchannels were fabricated with similar dimensions according to the limitations of the direct-printing process (width/depth 150 mu m/12 mu m). LIF was employed for detection to rule out any losses in separation efficiency due to the detector configuration. Two fluorescent dyes, coumarin and fluorescein, were used as model analytes. Devices were evaluated for the following parameters related to electrophoretic separations: EOF, heat dissipation, injection reproducibility, separation efficiency, and adsorption to channel wall.

Tectonic setting and U/Pb zircon dating of the plutonic Socorro Complex in the Transpressive Rio Paraíba do Sul Shear Belt, SE Brazil

The Precambrian Rio Paraíba do Sul Shear Belt comprises a 200-km-wide anastomosing network of NE-SW trending ductile shear zones extending over 1000 km of the southeastern coast of Brazil. Granulitic, gneissic-migmatitic, and granitoid terrains as well as low- to medium-grade metavolcanosedimentary sequences are included within it. These rocks were affected by strong contractional, tangential tectonics, due to west-northwestward oblique convergence of continental blocks. Subsequent transpressional tectonics accomodated large dextral, orogen-parallel movements and shortening. The plutonic Socorro Complex is one of many deformed granites with a foliation subparallel to that of the shear belt and exposes crosscutting relationships between its tectonic, magmatic, and metamorphic structures. These relationships point to a continuous magmatic evolution related to regional thrusts and strike slip, ductile shear zones. The tectonic and magmatic structural features of the Serra do Lopo Granite provide a model of emplacement by sheeting along shear zones during coeval strike-slip and cross shortening of country rocks. Geochronological data indicate that the main igneous activity of Socorro Complex spanned at least 55 million years, from the late stage of the northwestward ductile thrusting (650 Ma), through right-lateral strike slip (595 Ma) deformation. The country rocks yield discordant age data, which reflect a strong imprint of the Transamazonian tectono-metamorphic event (1.9 to 2.0 Ma). We propose a model for the origin of calcalkaline granites of the Ribeira Belt by partial melting of the lower crust with small contributions of the lithospheric mantle during transpressional thickening of plate margins, which were bounded by deep shear zones. The transpressional regime also seems to have focused granite migration from deeper into higher crustal levels along these shear zones.

Tax performance and reform in the Organization of Eastern Caribbean States (OECS)

Includes bibliography

Savings, investment and growth in the global age: analytical and policy issues

Includes bibliography

The institutionality of gender in the State: new analytical perspectives

Includes bibliography

A meta-analytical study about the relation of blood plasma addition in diets for piglets in the post-weaning and productive performance variables

The meta-analysis was used to evaluate the performance of piglets in post-weaning period, without imposition of sanitary challenge and fed diets containing blood plasma, obtained by spray-dried process (SDBP). Piglets are faced with normal challenges in post-weaning period such as environmental stress and the substitution of the liquid diet to a solid one. References regarding sanitary challenges were disregarded in this study. Only data regarding normal and expected challenges were considered. Data were obtained from indexed journals with information extracted from the material, methods and results sections of pre-selected scientific articles. First, the database was analyzed graphically to observe the distribution of data and presence of outliers. Afterwards correlation analysis and variance-covariance analyses were carried out. The database contained a total of 23 articles. The average initial weight of the piglets was 8.02. kg (4.00-9.28. kg) and the average initial age was 27 days (14-32 days). The average duration of feeding diets containing spray-dried blood plasma (SDBP) was 9 days (6-28 days). SDBP increased the feed conversion by 20.2% (P<0.05) during the initial period. Feed conversion during the total period was 10.2% higher (P<0.05) for animals fed with SDBP. Average daily weight gain and daily feed intake were not affected (P>0.05) during the entire period, but average daily gain was higher (P<0.05) for animals fed with SDBP during the initial period. The initial age of supplementation influenced the average daily weight gain and average daily feed intake of animals fed with SDBP. Better results were obtained than those obtained for animals up to 35 days of age fed diets without added SDBP supplementation. In early post-weaning period for piglets weaned up to 35 days of age, the SDBP supplementation positively influenced the average daily weight gain and feed conversion. © 2013 Elsevier B.V.

Relaxation to Fixed Points in the Logistic and Cubic Maps: Analytical and Numerical Investigation

Convergence to a period one fixed point is investigated for both logistic and cubic maps. For the logistic map the relaxation to the fixed point is considered near a transcritical bifurcation while for the cubic map it is near a pitchfork bifurcation. We confirmed that the convergence to the fixed point in both logistic and cubic maps for a region close to the fixed point goes exponentially fast to the fixed point and with a relaxation time described by a power law of exponent -1. At the bifurcation point, the exponent is not universal and depends on the type of the bifurcation as well as on the nonlinearity of the map.

Mass-Imbalanced Three-Body Systems in 2D: Bound States and the Analytical Approach to the Adiabatic Potential

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Influences of the harvest season on analytical characteristics of syrah grapes and wines produced in the northeast region of Brazil

The present study evaluated the main physical and chemical characteristics of Syrah grapes, coming from the tropical region of São Francisco river valley, harvested at different times and their relationship with analytical characteristics of resulting wines. Grapes came from the first half of 2009 harvest, collected at Casa Nova - Bahia, a semi-arid and hot region, comprising an interval from 84 days after pruning (84 dap) to the beginning of grape over-ripening, 133 days after pruning (133 dap). Harvests at 84, 91, 98, 105, 112, 119, 126 and 133 dap, were analyzed for pH, soluble solids and acidity in grapes, which were then processed for wine production. Maximum sugar/acidity ratio (s/a = 56) were observed in grapes harvested between 126 and 133 dap, coincided with the highest concentration of anthocyanins (851 mg L-1 ) and total tannins (2.6 g L-1 ) in the resulting wines, indicating that grapes collected between 126 and 133 dap showed the best potential for winemaking in the tropical climate of São Francisco river valley. This result was confirmed by the analytical characterization of wines, that, between 126 and 133 dap, showed 12.8% alcohol, 31 g L-1 dry extract, 5.6 g L-1 ashes and a TPI of 58, using only one pumping per day, for 5 days maceration. Syrah grapes considered in the present work presented a good evolution of maturation, and grapes harvested between 126 and 133 days after pruning, showed the best oenological potential for the development of red wine. The use of pH and soluble solids appeared useful parameters in the estimation of maturation degree and quality potential of grapes for winemaking.

Petrogenesis of syntectonic granites emplaced at the transition from thrusting to transcurrent tectonics in post-collisional setting: Whole-rock and Sr-Nd-Pb isotope geochemistry in the Neoproterozoic Quatro Ilhas and Mariscal Granites, Southern Brazil

The Neoproterozoic post-collisional period in southern Brazil (650-580 Ma) is characterized by substantial volumes of magma emplaced along the active shear zones that compose the Southern Brazilian Shear Belt. The early-phase syntectonic magmatism (630-610 Ma) is represented by the porphyritic, high-K, metaluminous to peraluminous Quatro Ilhas Granitoids and the younger heterogranular, slightly peraluminous Mariscal Granite. Quatro II has Granitoids include three main petrographic varieties (muscovite-biotite granodiorite mbg; biotite monzogranite - bmz: and leucogranite - lcg) that, although sharing some significant geochemical characteristics, are not strictly comagmatic, as shown by chemical and Sr-Nd-Pb isotope data. The most primitive muscovite-biotite granodiorite was produced by contamination of more mafic melts (possibly with some mantle component) with peraluminous crustal melts; the biotite monzogranite, although more felsic, has higher Ca, MgO,TiO2 and Ba, and lower K2O, FeOt, Sr and Rb contents, possibly reflecting some mixing with coeval mafic magmas of tholeiitic affinity; the leucogranite may be derived from pure crustal melts. The Mariscal Granite is formed by two main granite types which occur intimately associated in the same pluton, one with higher K (5-6.5 wt.% K2O) high Rb and lower CaO, Na2O, Ba and Zr as compared to the other (3-5 wt.% of K2O). The two Mariscal Granite varieties have compositional correspondence with fine-grained granites (fgg) that occur as tabular bodies which intruded the Quatro Ilhas Granoitoids before they were fully crystallized, and are inferred to correspond to the Mariscal Granite feeders, an interpretation that is reinforced by similar U-Pb zircon crystallization ages. The initial evolution of the post-collisional magmatism, marked by the emplacement of the Quatro Ilhas Granitoids varieties, activated sources that produced mantle and crustal magmas whose emplacement was controlled both by flat-lying and transcurrent structures. The transition from thrust to transcurrent-related tectonics coincides with the increase in the proportion of crustal-derived melts. The transcurrent tectonics seems to have played an essential role in the generation of mantle-derived magmas and may have facilitated their interaction with crustal melts which seem to be to a large extent the products of reworking of orthogneiss protoliths. (C) 2012 Elsevier B.V. All rights reserved.

Retinol binding protein 4 and retinol in steatotic and nonsteatotic rat livers in the setting of partial hepatectomy under ischemia/reperfusion

Steatotic livers show increased hepatic damage and impaired regeneration after partial hepatectomy (PH) under ischemia/reperfusion (I/R), which is commonly applied in clinical practice to reduce bleeding. The known function of retinol-binding protein 4 (RBP4) is to transport retinol in the circulation. We examined whether modulating RBP4 and/or retinol could protect steatotic and nonsteatotic livers in the setting of PH under I/R. Steatotic and nonsteatotic livers from Zucker rats were subjected to PH (70%) with 60 minutes of ischemia. RBP4 and retinol levels were measured and altered pharmacologically, and their effects on hepatic damage and regeneration were studied after reperfusion. Decreased RBP4 levels were observed in both liver types, whereas retinol levels were reduced only in steatotic livers. RBP4 administration exacerbated the negative consequences of liver surgery with respect to damage and liver regeneration in both liver types. RBP4 affected the mobilization of retinol from steatotic livers, and this revealed actions of RBP4 independent of simple retinol transport. The injurious effects of RBP4 were not due to changes in retinol levels. Treatment with retinol was effective only for steatotic livers. Indeed, retinol increased hepatic injury and impaired liver regeneration in nonsteatotic livers. In steatotic livers, retinol reduced damage and improved regeneration after surgery. These benefits of retinol were associated with a reduced accumulation of hepatocellular fat. Thus, strategies based on modulating RBP4 could be ineffective and possibly even harmful in both liver types in the setting of PH under I/R. In terms of clinical applications, a retinol pretreatment might open new avenues for liver surgery that specifically benefit the steatotic liver. Liver Transpl 18:1198-1208, 2012. (c) 2012 AASLD.

Analytical challenges in the fields of Nanobioscience and Nanobiotecnology: integrated methods for separation and characterization

Nano(bio)science and nano(bio)technology play a growing and tremendous interest both on academic and industrial aspects. They are undergoing rapid developments on many fronts such as genomics, proteomics, system biology, and medical applications. However, the lack of characterization tools for nano(bio)systems is currently considered as a major limiting factor to the final establishment of nano(bio)technologies. Flow Field-Flow Fractionation (FlFFF) is a separation technique that is definitely emerging in the bioanalytical field, and the number of applications on nano(bio)analytes such as high molar-mass proteins and protein complexes, sub-cellular units, viruses, and functionalized nanoparticles is constantly increasing. This can be ascribed to the intrinsic advantages of FlFFF for the separation of nano(bio)analytes. FlFFF is ideally suited to separate particles over a broad size range (1 nm-1 μm) according to their hydrodynamic radius (rh). The fractionation is carried out in an empty channel by a flow stream of a mobile phase of any composition. For these reasons, fractionation is developed without surface interaction of the analyte with packing or gel media, and there is no stationary phase able to induce mechanical or shear stress on nanosized analytes, which are for these reasons kept in their native state. Characterization of nano(bio)analytes is made possible after fractionation by interfacing the FlFFF system with detection techniques for morphological, optical or mass characterization. For instance, FlFFF coupling with multi-angle light scattering (MALS) detection allows for absolute molecular weight and size determination, and mass spectrometry has made FlFFF enter the field of proteomics. Potentialities of FlFFF couplings with multi-detection systems are discussed in the first section of this dissertation. The second and the third sections are dedicated to new methods that have been developed for the analysis and characterization of different samples of interest in the fields of diagnostics, pharmaceutics, and nanomedicine. The second section focuses on biological samples such as protein complexes and protein aggregates. In particular it focuses on FlFFF methods developed to give new insights into: a) chemical composition and morphological features of blood serum lipoprotein classes, b) time-dependent aggregation pattern of the amyloid protein Aβ1-42, and c) aggregation state of antibody therapeutics in their formulation buffers. The third section is dedicated to the analysis and characterization of structured nanoparticles designed for nanomedicine applications. The discussed results indicate that FlFFF with on-line MALS and fluorescence detection (FD) may become the unparallel methodology for the analysis and characterization of new, structured, fluorescent nanomaterials.

Detailed study of the seismotectonic setting in the Lucanian Apennines and surrounding areas (Southern Italy)

In this research work I analyzed the instrumental seismicity of Southern Italy in the area including the Lucanian Apennines and Bradano foredeep, making use of the most recent seismological database available so far. I examined the seismicity occurred during the period between 2001 and 2006, considering 514 events with magnitudes M ≥ 2.0. In the first part of the work, P- and S-wave arrival times, recorded by the Italian National Seismic Network (RSNC) operated by the Istituto Nazionale di Geofisica e Vulcanologia (INGV), were re-picked along with those of the SAPTEX temporary array (2001–2004). For some events located in the Upper Val d'Agri, I also used data from the Eni-Agip oil company seismic network. I computed the VP/VS ratio obtaining a value of 1.83 and I carried out an analysis for the one-dimensional (1D) velocity model that approximates the seismic structure of the study area. After this preliminary analysis, making use of the records obtained in the SeSCAL experiment, I incremented the database by handpicking new arrival times. My final dataset consists of 15,666 P- and 9228 S-arrival times associated to 1047 earthquakes with magnitude ML ≥ 1.5. I computed 162 fault-plane solutions and composite focal mechanisms for closely located events. I investigated stress field orientation inverting focal mechanism belonging to the Lucanian Apennine and the Pollino Range, both areas characterized by more concentrated background seismicity. Moreover, I applied the double difference technique (DD) to improve the earthquake locations. Considering these results and different datasets available in the literature, I carried out a detailed analysis of single sub-areas and of a swarm (November 2008) recorded by SeSCAL array. The relocated seismicity appears more concentrated within the upper crust and it is mostly clustered along the Lucanian Apennine chain. In particular, two well-defined clusters were located in the Potentino and in the Abriola-Pietrapertosa sector (central Lucanian region). Their hypocentral depths are slightly deeper than those observed beneath the chain. I suggest that these two seismic features are representative of the transition from the inner portion of the chain with NE-SW extension to the external margin characterized by dextral strike-slip kinematics. In the easternmost part of the study area, below the Bradano foredeep and the Apulia foreland, the seismicity is generally deeper and more scattered and is associated to the Murge uplift and to the small structures present in the area. I also observed a small structure NE-SW oriented in the Abriola-Pietrapertosa area (activated with a swarm in November 2008) that could be considered to act as a barrier to the propagation of a potential rupture of an active NW-SE striking faults system. Focal mechanisms computed in this study are in large part normal and strike-slip solutions and their tensional axes (T-axes) have a generalized NE-SW orientation. Thanks to denser coverage of seismic stations and the detailed analysis, this study is a further contribution to the comprehension of the seismogenesis and state of stress of the Southern Apennines region, giving important contributions to seismotectonic zoning and seismic hazard assessment.