Chemical mass closure and source-specific composition of atmospheric particles

It has been known for decades that particles can cause adverse health effects as they are deposited within the respiratory system. Atmospheric aerosol particles influence climate by scattering solar radiation but aerosol particles act also as the nuclei around which cloud droplets form. The principal objectives of this thesis were to investigate the chemical composition and the sources of fine particles in different environments (traffic, urban background, remote) as well as during some specific air pollution situations. Quantifying the climate and health effects of atmospheric aerosols is not possible without detailed information of the aerosol chemical composition. Aerosol measurements were carried out at nine sites in six countries (Finland, Germany, Czech, Netherlands, Greece and Italy). Several different instruments were used in order to measure both the particulate matter (PM) mass and its chemical composition. In the off-line measurements the samples were collected first on a substrate or filter and gravimetric and chemical analysis were conducted in the laboratory. In the on-line measurements the sampling and analysis were either a combined procedure or performed successively within the same instrument. Results from the impactor samples were analyzed by the statistical methods. This thesis comprises also a work where a method for the determination carbonaceous matter size distribution by using a multistage impactor was developed. It was found that the chemistry of PM has usually strong spatial, temporal and size-dependent variability. In the Finnish sites most of the fine PM consisted of organic matter. However, in Greece sulfate dominated the fine PM and in Italy nitrate made the largest contribution to the fine PM. Regarding the size-dependent chemical composition, organic components were likely to be enriched in smaller particles than inorganic ions. Data analysis showed that organic carbon (OC) had four major sources in Helsinki. Secondary production was the major source in Helsinki during spring, summer and fall, whereas in winter biomass combustion dominated OC. The significant impact of biomass combustion on OC concentrations was also observed in the measurements performed in Central Europe. In this thesis aerosol samples were collected mainly by the conventional filter and impactor methods which suffered from the long integration time. However, by filter and impactor measurements chemical mass closure was achieved accurately, and a simple filter sampling was found to be useful in order to explain the sources of PM on the seasonal basis. The online instruments gave additional information related to the temporal variations of the sources and the atmospheric mixing conditions.

Engine wear and used oil analysis - comparative study in high speed diesel engines

The operational life and reliability of I.C. engines are limited to a certain extent by the break down of the engine components due to wear. It is advantageous to know the condition of an engine and its components without disassembling for detailed measurements. This paper describes the possibility of employing chemical analysis of the used crank case oil to predict the wear of engine components. It is concluded that the acidity and carbon contents of the crank case oil play a significant role in assessing the wear of copper-lead bearings used for the big end of the connecting rod.

Engine wear and used oil analysis-A comparative study in high speed diesel engines

The operational life and reliability of I.C. engines are limited to a certain extent by the break down of the engine components due to wear. It is advantageous to know the condition of an engine and its components without disassembling for detailed measurements. This paper describes the possibility of employing chemical analysis of the used crank case oil to predict the wear of engine components. It is concluded that the acidity and carbon contents of the crank case oil play a significant role in assessing the wear of copper-lead bearings used for the big end of the connecting rod.

Synthesis, characterisation and thermal analysis of copper (II) and chromium (II, III) hydrazine carboxylates

Copper(II) hydrazine carboxylate monohydrate, Cu(N2H3COO)2·H2O and chromium (II, III) hydrazine carboxylate hydrates, Cu(N2H3COO)2·H2O and Cu(N2H3COO)2·3H2O have been prepared and characterised by chemical analysis, IR, visible spectra and magnetic measurements. Thermal analysis of the copper complex yields a mixture of copper metal and copper oxide. Chromium complexes on thermal decomposition yield Cr2O3 as residue. Decomposition of chromium(HI) complex under hydrothermal conditions yield CrOOH, a precursor to CrO2.

Chemical toughening of epoxies. I. Structural modification of epoxy resins by reaction with hydroxy-terminated poly (butadiene-co-acrylonitrile)

In an attempt to toughen the epoxy resin matrix for fiber-reinforced composite applications, a chemical modification procedure of a commercially available bisphenol-A-based epoxy resin using reactive liquid rubber HTBN [hydroxy-terminated poly(butadiene-co-acrylonitrile)] and TDI (tolylene diisocyanate) is described. The progress of the reaction and the structural changes during modification process are studied using IR spectroscopy, viscosity data, and chemical analysis (epoxy value determination). The studies support the proposition that TDI acts as a coupling agent between the epoxy and HTBN, forming a urethane linkage with the former and an oxazolidone ring with the latter. The chemical reactions that possibly take place during the modification are discussed.

Chemical toughening of epoxies. I. Structural modification of epoxy resins by reaction with hydroxy-terminated poly(butadiene-co-acrylonitrile)

In an attempt to toughen the epoxy resin matrix for fiber-reinforced composite applications, a chemical modification procedure of a commercially available bisphenol-A-based epoxy resin using reactive liquid rubber HTBN [hydroxy-terminated poly(butadiene-co-acrylonitrile)] and TDI (tolylene diisocyanate) is described. The progress of the reaction and the structural changes during modification process are studied using IR spectroscopy, viscosity data, and chemical analysis (epoxy value determination). The studies support the proposition that TDI acts as a coupling agent between the epoxy and HTBN, forming a urethane linkage with the former and an oxazolidone ring with the latter. The chemical reactions that possibly take place during the modification are discussed.

Some Themes in Chemical Crystallography Pertinent to the Indian Contribution

It is particularly appropriate that the Journal of the Indian Institute of Science is bringing out a commemorative issue to mark the International Year of Crystallography 2014 (IYCr2014). India has had a strong crystallographic tradition, and the earliest work in what may be described as structural crystallography from this country is the work of K. Banerjee on the determination of the crystal structure of naphthalene in 1930. The Indian Institute of Science itself has played no small part in establishing and sustaining the subject of crystallography in this country. A large number of papers in this special issue are written by authors who have either have been trained in the Institute or who have some kind of professional association with this organization. In this article I will try to capture some unique features that characterize the intersection of the crystallographic and the chemical domains, mostly as they pertain to the Indian contribution to this subject. Crystallography is of course is as old as chemistry itself, and some would say it is even older. The relationships between chemistry and crystallography go back to much before the discovery of diffraction of X-rays by crystals.The discovery of polymorphism by Mitscherlisch in 1822, Haüy’s formulation of the molecule integrante, and the work of Fedorov and Groth on the identification of crystals from their morphology alone, are well known examples of such relationships.A very early article by Tutton speaks of “crystallo-chemical analysis���. In this article, I shall, however, be dealing with the interplay of chemistry and crystallography only in the post diffraction era, that is, after 1912. Much had been written and said about chemical crystallography, and even within the context of the present special issue, there is a review of chemical crystallography in India including some futuristic trends. This topic was also reviewed by Nangia in a special publication brought out by Indian Academy of Sciences in 2009,and by Desiraju in a special publication brought out by the Indian National Science Academy in 2010. A rather detailed account of crystallography in India appeared in 2007 in the newsletter of the International Union of Crystallography (IUCr) in which chemical crystallography was detailed. Since all these publications are fairly recent there is little need for me to attempt a comprehensive coverage of chemical crystallography in India in this short review

The changing chemical composition of chalk streams and rivers

The area studied was the River Frome system below Dorchester. The main river has its origins mainly in chalk springs, although some of its tributaries have surface run-off from farm lands and heath-lands. Thus the chemistry of the river is affected by changes in land practice and differences in the geology of the catchment area. Regular chemical analysis of chalk waters started at the River Laboratory in 1964, Regular weekly analyses have been carried out since 1965 at Bere Stream (a small chalk stream) and the River Frome (a large chalk stream); also single samples have been analysed to provide preliminary information. In 1970-71 an attempt was made to discover the contribution each main source made to the flow and chemical composition of the River Frome. Results of these investigations are presented in the paper.

UV-photooxidation as pretreatment step in inorganic analysis of environmental samples

Many laboratories deal with the determination of heavy metals, carbon, nitrogen and phosphorus. The first step in chemical analysis is a proper preparation of the investigated samples. The presence of organic substances can cause problems in many analytical methods. This paper describes the application of UV irradiation as a method of destruction of organic matter in the investigated samples.

Chemical characteristic of bioactive polysaccharides isolated from Ornithogalum caudatum Ait.

A water-soluble crude extract prepared from Ornithogalum caudatum Ait. (OCA) showing a high immunomodulating activitiy was isolated and characterized by virtue of get filtration and column chromatography. The presence of the monosaccharides has been established by the chemical analysis. The quantitative analysis of the alditol acetate derivatives of them showed the ratios of the monosaccharides analyzed by means of GC respectively. The concentrations of protein(280 nm) and carbohydrate (496 nm) were detected respectively. The information of the molecular weight from the pure polysaccharide was obtained by several standard Dextrans from the Sephadex chromatography.

Analysis of the estrogenic components in kudzu root by bioassay and high performance liquid chromatography

The estrogenic activity of the Chinese herb kudzu root was investigated by a recombinant yeast screening assay (YES). Isoflavones are the main components in the plant, of which puerarin is the most abundant one. The kudzu root extract was separated into four fractions according to the polarity. The crude extract and its sub-fractions, except the water fraction, showed clear estrogenic activity and the potencies were in the range of 10(-3) to 10(-1) g/l. The ligand potency was used to compare the estrogenic activity of these fractions. The crude extract and its sub-fractions were further analyzed by high performance liquid chromatography (HPLC) to correlate the activity and the active components. Bioassay and chemical analysis showed that theoretical estrogenic activity expressed as equivalent 17 beta-estradiol concentration or the cumulative effects are comparable to that experimentally determined by YES. The results showed that the high content of isoflavones as well as the high estrogenic activity could make kudzu root extract an interesting candidate for hormone replacement therapy. (c) 2005 Elsevier Ltd. All rights reserved.

Mass spectrometry-based metabolomics applied to the chemical safety of food

Mass spectrometry (MS)-based metabolomics is emerging as an important field of research in many scientific areas, including chemical safety of food. A particular strength of this approach is its potential to reveal some physiological effects induced by complex mixtures of chemicals present at trace concentrations. The limitations of other analytical approaches currently employed to detect low-dose and mixture effects of chemicals make detection very problematic. Besides this basic technical challenge, numerous analytical choices have to be made at each step of a metabolomics study, and each step can have a direct impact on the final results obtained and their interpretation (i.e. sample preparation, sample introduction, ionization, signal acquisition, data processing, and data analysis). As the application of metabolomics to chemical analysis of food is still in its infancy, no consensus has yet been reached on defining many of these important parameters. In this context, the aim of the present study is to review all these aspects of MS-based approaches to metabolomics, and to give a comprehensive, critical overview of the current state of the art, possible pitfalls, and future challenges and trends linked to this emerging field. (C) 2010 Elsevier Ltd. All rights reserved.

Ecotoxicological screening of Kenyan tannery dust using a luminescent-based bacterial biosensor

Ecotoxicological screening of dust sampled throughout a Kenyan tannery was conducted using a luminescence (lux)-based bacterial biosensor for both solid and liquid assays. This was complemented by chemical analysis in an attempt to identify possible causative toxic components. The biosensor results showed a highly significant (p <0.001) difference in both solid and liquid phase toxicity in samples collected from various identified sampling points in the tannery. A positive correlation was observed between results of the solid and liquid phase techniques, for most of the sampling points indicating that the toxic contaminants were bioavailable both in the solid and liquid state. However, the results generally indicated toxicity associated with liquid phase except certain areas in solid phase such as chemical handling, buffing area and weighing. The most toxic tannery area identified was the weighing area (p <0.001), showing the lowest bioluminescence for both the solid (0.38 +/- 2.21) and liquid phases (0.01 +/- 0.001). Chromium was the metal present in the highest concentration indicating levels higher than the stipulated regulatory requirement of 0.5 mg Cr/m3 for total Cr (highest Cr concentration was at chemical handling at 209.24 mg l(-1)) in all dust samples. The weighing area had the highest Ni concentration (1.87 mg l(-1)) and the chemical handling area showed the highest Zn concentration (31.9 mg l(-1)). These results raise environmental health concerns, as occupational exposure to dust samples from this site has been shown to give rise to elevated concentrations (above the stipulated levels) of chromium in blood, urine and some body tissues, with inhalation being the main route. Health and Safety Executive (HSE), UK, and American Conference of Governmental Industrial Hygienist (ACGIH) and National Institute for Occupational Safety and Health (NIOSH), USA stipulates an occupational exposure limit of 0.5 mg Cr/m3 (8 h TWA) for total chromium. However, schedule 1 of Controls of substances hazardous to health (COSHH) regulations developed by HSE, indicate 0.05 mg m3 (8 h TWA reference periods) to be the limit for Cr (VI) exposure. The exposure limit for individual (e.g., Cr, Zn, Ni etc.) contaminants (homogeneity) was not exceeded, but potential impact of heterogeneity (multi-element synergistic effect) on toxicity requires application of the precautionary principle.

Genotoxicity in humans and indicator species exposed to uranium wastes

Os riscos dos resíduos provenientes da extração do urânio estão associados ao seu conteúdo em metais e radionuclídeos, o que levanta preocupações às autoridades governamentais e à população em geral. As populações humanas e outras espécies animais que vivem em zonas de exploração de urânio poderão estar expostas à radiação através de resíduos e poeiras radioactivase também através de água e alimentos contaminados. A determinação dos riscos deste tipo de contaminantes é feita, principalmente, através da análise química de amostras ambientais, dando-se menos importância à determinação de efeitos biológicos. A determinação de efeitos biológicos causados pela exposição a poluentes, tem-se revelado muito importante para uma avaliação da qualidade ambiental, de modo a providenciar indicações acerca dos efeitos negativos nos seres vivos e também para complementar a informação dada pelas análises químicas de amostras ambientais. Este facto levou ao estabelecimento de biomarcadores, que consistem em respostas biológicas adversas que são específicas de uma exposição a toxinas ambientais, para serem usadas como ferramentas de avaliação da qualidade ambiental. Neste trabalho foram analisadas respostas a nível molecular e celular, em minhocas, ratinhos do campo e humanos, a fim de determinar o risco químico e radiológico dos resíduos provenientes da mina de urânio da Cunha Baixa. Este trabalho teve também como objectivo a clarificação das respostas subjacentes à exposição a metais e radionuclídeos, a fim de permitir o desenvolvimento de potenciais novos biomarcadores moleculares. Durante este trabalho foram efectuados ensaios com minhocas, em que estas foram expostas durante 56 dias a solo contaminado proveniente da mina de urânio da Cunha Baixa, em laboratório e in situ. Durante a exposição foram analisados vários parâmetros, como o crescimento, reprodução, bioacumulação de metais e radionuclídeos, histopatologia, danos no DNA, citotoxicidade e perfil de expressão genética. Para além disso, foram amostrados ratinhos do campo na mina de urânio da Cunha Baixa e numa área de referência para determinação de danos no DNA, níveis de expressão e mutações em genes supressores de tumores e também bioacumulação de metais. Por fim, foram recolhidas amostras de sangue em voluntários saudáveis pertencentes à população da aldeia da Cunha Baixa, para determinação de danos no DNA, imunofenotipagem e quantificação de metais no sangue. Os resultados revelaram que as minhocas assim como os ratinhos do campo foram negativamente afetados pela exposição aos resíduos mineiros em todos os níveis de organização biológica aqui analisados, o que faz destes organismos bons indicadores para a determinação do risco destas áreas contaminadas, evidenciando o potencial risco da exposição a estes contaminantes. Para além disso, o estudo feito à população da Cunha Baixa revelou danos no ADN e diminuição de populações importantes de células imunitárias (nomeadamente linfócitos T e NK), o que poderá resultar da exposição aos resíduos da mina, tornando as pessoas mais susceptíveis ao desenvolvimento de processos de carcinogénese. O presente estudo contribuiu significativamente para a caracterização dos riscos da exposição a resíduos provenientes de minas de urânio abandonadas, evidenciando os seus efeitos negativos a nível molecular e celular, que potencialmente poderão causar instabilidade genómica e aumentar o risco de desenvolvimento de doenças genéticas.