An examination of monotony and hypovigilance, independent of fatigue : relevance to road safety

Driving is a vigilance task, requiring sustained attention to maintain performance and avoid crashes. Hypovigilance (i.e., marked reduction in vigilance) while driving manifests as poor driving performance and is commonly attributed to fatigue (Dinges, 1995). However, poor driving performance has been found to be more frequent when driving in monotonous road environments, suggesting that monotony plays a role in generating hypovigilance (Thiffault & Bergeron, 2003b). Research to date has tended to conceptualise monotony as a uni-dimensional task characteristic, typically used over a prolonged period of time to facilitate other factors under investigation, most notably fatigue. However, more often than not, more than one exogenous factor relating to the task or operating environment is manipulated to vary or generate monotony (Mascord & Heath, 1992). Here we aimed to explore whether monotony is a multi-dimensional construct that is determined by characteristics of both the task proper and the task environment. The general assumption that monotony is a task characteristic used solely to elicit hypovigilance or poor performance related to fatigue appears to have led to there being little rigorous investigation into the exact nature of the relationship. While the two concepts are undoubtedly linked, the independent effect of monotony on hypovigilance remains largely ignored. Notwithstanding, there is evidence that monotony effects can emerge very early in vigilance tasks and are not necessarily accompanied by fatigue (see Meuter, Rakotonirainy, Johns, & Wagner, 2005). This phenomenon raises a largely untested, empirical question explored in two studies: Can hypovigilance emerge as a consequence of task and/or environmental monotony, independent of time on task and fatigue? In Study 1, using a short computerised vigilance task requiring responses to be withheld to infrequent targets, we explored the differential impacts of stimuli and task demand manipulations on the development of a monotonous context and the associated effects on vigilance performance (as indexed by respone errors and response times), independent of fatigue and time on task. The role of individual differences (sensation seeking, extroversion and cognitive failures) in moderating monotony effects was also considered. The results indicate that monotony affects sustained attention, with hypovigilance and associated performance worse in monotonous than in non-monotonous contexts. Critically, performance decrements emerged early in the task (within 4.3 minutes) and remained consistent over the course of the experiment (21.5 minutes), suggesting that monotony effects can operate independent of time on task and fatigue. A combination of low task demands and low stimulus variability form a monotonous context characterised by hypovigilance and poor task performance. Variations to task demand and stimulus variability were also found to independently affect performance, suggesting that monotony is a multi-dimensional construct relating to both task monotony (associated with the task itself) and environmental monotony (related to characteristics of the stimulus). Consequently, it can be concluded that monotony is multi-dimensional and is characterised by low variability in stimuli and/or task demands. The proposition that individual differences emerge under conditions of varying monotony with high sensation seekers and/or extroverts performing worse in monotonous contexts was only partially supported. Using a driving simulator, the findings of Study 1 were extended to a driving context to identify the behavioural and psychophysiological indices of monotony-related hypovigilance associated with variations to road design and road side scenery (Study 2). Supporting the proposition that monotony is a multi-dimensional construct, road design variability emerged as a key moderating characteristic of environmental monotony, resulting in poor driving performance indexed by decrements in steering wheel measures (mean lateral position). Sensation seeking also emerged as a moderating factor, where participants high in sensation seeking tendencies displayed worse driving behaviour in monotonous conditions. Importantly, impaired driving performance was observed within 8 minutes of commencing the driving task characterised by environmental monotony (low variability in road design) and was not accompanied by a decline in psychophysiological arousal. In addition, no subjective declines in alertness were reported. With fatigue effects associated with prolonged driving (van der Hulst, Meijman, & Rothengatter, 2001) and indexed by drowsiness, this pattern of results indicates that monotony can affect driver vigilance, independent of time on task and fatigue. Perceptual load theory (Lavie, 1995, 2005) and mindlessness theory (Robertson, Manly, Andrade, Baddley, & Yiend, 1997) provide useful theoretical frameworks for explaining and predicting monotony effects by positing that the low load (of task and/or stimuli) associated with a monotonous task results in spare attentional capacity which spills over involuntarily, resulting in the processing of task-irrelevant stimuli or task unrelated thoughts. That is, individuals – even when not fatigued - become easily distracted when performing a highly monotonous task, resulting in hypovigilance and impaired performance. The implications for road safety, including the likely effectiveness of fatigue countermeasures to mitigate monotony-related driver hypovigilance are discussed.

Designing university, government and industry community engagement to build informed and effective interventions in the area of road safety

Individuals, community organisations and industry have always been involved to varying degrees in efforts to address the Queensland road toll. Traditionally, road crash prevention efforts have been led by state and local government organisations. While community and industry groups have sometimes become involved (e.g. Driver Reviver campaign), their efforts have largely been uncoordinated and under-resourced. A common strength of these initiatives lies in the energy, enthusiasm and persistence of community-based efforts. Conversely, a weakness has sometimes been the lack of knowledge, awareness or prioritisation of evidence-based interventions or their capacity to build on collaborative efforts. In 2000, the Queensland University of Technology’s Centre for Accident Research and Road Safety – Queensland (CARRS-Q) identified this issue as an opportunity to bridge practice and research and began acknowledging a selection of these initiatives, in partnership with the RACQ, through the Queensland Road Safety Awards program. After nine years it became apparent there was need to strengthen this connection, with the Centre establishing a Community Engagement Workshop in 2009 as part of the overall Awards program. With an aim of providing community participants opportunities to see, hear and discuss the experiences of others, this event was further developed in 2010, and with the collaboration of the Queensland Department of Transport and Main Roads, the RACQ, Queensland Police Service and Leighton Contractors Pty Ltd, a stand-alone Queensland Road Safety Awards Community Engagement Workshop was held in 2010. Each collaborating organisation recognised a need to mobilise the community through effective information and knowledge sharing, and recognised that learning and discussion can influence lasting behaviour change and action in this often emotive, yet not always evidence-based, area. This free event featured a number of speakers representing successful projects from around Australia and overseas. Attendees were encouraged to interact with the speakers, to ask questions, and most importantly, build connections with other attendees to build a ‘community road safety army’ all working throughout Australia on projects underpinned by evaluated research. The workshop facilitated the integration of research, policy and grass-roots action enhancing the success of community road safety initiatives. For collaboration partners, the event enabled them to transfer their knowledge in an engaged approach, working within a more personal communication process. An analysis of the success factors for this event identified openness to community groups and individuals, relevance of content to local initiatives, generous support with the provision of online materials and ongoing communication with key staff members as critical and supports the view that the university can directly provide both the leadership and the research needed for effective and credible community-based initiatives to address injury and death on the roads.

Is there an App for that? : social media uses for road safety

The use of social media has increased dramatically in recent years in the areas of public health and injury prevention, with many organisations creating online and social media content. Despite the adoption of such media by modern society, research relating to the design and evaluation of social media for the promotion of health issues is very much in its infancy. A timely review of the available evidence in relation to the use of social media campaigns from both the road safety and broader public health context will be undertaken. In particular, this paper will address the questions of what social media should be developed, how it should be evaluated, as well as what should be the key measures of success and to what extent do these measures relate to practically significant outcomes, such as behaviour change. Much like more traditional media campaigns, social media may be best regarded as another approach within the array of potential approaches that a health advertising researcher or practitioner may utilise. With younger demographics becoming less likely to engage with more traditional advertising mediums relative to their preference for social media, social media‟s most important role in the road safety advertising context may be to offer the means of delivering road safety messages to high risk, younger road users.

Feasibility of using health data sources to inform product safety surveillance in Queensland : a report for the Queensland Injury Prevention Council

This report provides an evaluation of the current available evidence-base for identification and surveillance of product-related injuries in children in Queensland. While the focal population was children in Queensland, the identification of information needs and data sources for product safety surveillance has applicability nationally for all age groups. The report firstly summarises the data needs of product safety regulators regarding product-related injury in children, describing the current sources of information informing product safety policy and practice, and documenting the priority product surveillance areas affecting children which have been a focus over recent years in Queensland. Health data sources in Queensland which have the potential to inform product safety surveillance initiatives were evaluated in terms of their ability to address the information needs of product safety regulators. Patterns in product-related injuries in children were analysed using routinely available health data to identify areas for future intervention, and the patterns in product-related injuries in children identified in health data were compared to those identified by product safety regulators. Recommendations were made for information system improvements and improved access to and utilisation of health data for more proactive approaches to product safety surveillance in the future.

Parliament and community road safety

In the past, Queensland parliamentary committees have successfully assisted in the introduction of evidence-based policy and legislation and this presentation will describe how Parliament supports road safety through its committees. The presentation will examine the strengths of parliamentary committees in the Westminster system, provide an overview of the reformed committee system and discuss an example of a previous road safety inquiry (completed under the former committee system). Developing an understanding of parliamentary committees will help road safety practitioners to present their ideas in an appropriate manner that will encourage the examination of their ideas by parliamentary committees and increase the likelihood that their suggestions will be included as recommendations within a committee report and subsequently acted upon by the government.

The flammability of metallic materials in normal and reduced gravity

Metallic materials exposed to oxygen-enriched atmospheres – as commonly used in the medical, aerospace, aviation and numerous chemical processing industries – represent a significant fire hazard which must be addressed during design, maintenance and operation. Hence, accurate knowledge of metallic materials flammability is required. Reduced gravity (i.e. space-based) operations present additional unique concerns, where the absence of gravity must also be taken into account. The flammability of metallic materials has historically been quantified using three standardised test methods developed by NASA, ASTM and ISO. These tests typically involve the forceful (promoted) ignition of a test sample (typically a 3.2 mm diameter cylindrical rod) in pressurised oxygen. A test sample is defined as flammable when it undergoes burning that is independent of the ignition process utilised. In the standardised tests, this is indicated by the propagation of burning further than a defined amount, or „burn criterion.. The burn criterion in use at the onset of this project was arbitrarily selected, and did not accurately reflect the length a sample must burn in order to be burning independent of the ignition event and, in some cases, required complete consumption of the test sample for a metallic material to be considered flammable. It has been demonstrated that a) a metallic material.s propensity to support burning is altered by any increase in test sample temperature greater than ~250-300 oC and b) promoted ignition causes an increase in temperature of the test sample in the region closest to the igniter, a region referred to as the Heat Affected Zone (HAZ). If a test sample continues to burn past the HAZ (where the HAZ is defined as the region of the test sample above the igniter that undergoes an increase in temperature of greater than or equal to 250 oC by the end of the ignition event), it is burning independent of the igniter, and should be considered flammable. The extent of the HAZ, therefore, can be used to justify the selection of the burn criterion. A two dimensional mathematical model was developed in order to predict the extent of the HAZ created in a standard test sample by a typical igniter. The model was validated against previous theoretical and experimental work performed in collaboration with NASA, and then used to predict the extent of the HAZ for different metallic materials in several configurations. The extent of HAZ predicted varied significantly, ranging from ~2-27 mm depending on the test sample thermal properties and test conditions (i.e. pressure). The magnitude of the HAZ was found to increase with increasing thermal diffusivity, and decreasing pressure (due to slower ignition times). Based upon the findings of this work, a new burn criterion requiring 30 mm of the test sample to be consumed (from the top of the ignition promoter) was recommended and validated. This new burn criterion was subsequently included in the latest revision of the ASTM G124 and NASA 6001B international test standards that are used to evaluate metallic material flammability in oxygen. These revisions also have the added benefit of enabling the conduct of reduced gravity metallic material flammability testing in strict accordance with the ASTM G124 standard, allowing measurement and comparison of the relative flammability (i.e. Lowest Burn Pressure (LBP), Highest No-Burn Pressure (HNBP) and average Regression Rate of the Melting Interface(RRMI)) of metallic materials in normal and reduced gravity, as well as determination of the applicability of normal gravity test results to reduced gravity use environments. This is important, as currently most space-based applications will typically use normal gravity information in order to qualify systems and/or components for reduced gravity use. This is shown here to be non-conservative for metallic materials which are more flammable in reduced gravity. The flammability of two metallic materials, Inconel® 718 and 316 stainless steel (both commonly used to manufacture components for oxygen service in both terrestrial and space-based systems) was evaluated in normal and reduced gravity using the new ASTM G124-10 test standard. This allowed direct comparison of the flammability of the two metallic materials in normal gravity and reduced gravity respectively. The results of this work clearly show, for the first time, that metallic materials are more flammable in reduced gravity than in normal gravity when testing is conducted as described in the ASTM G124-10 test standard. This was shown to be the case in terms of both higher regression rates (i.e. faster consumption of the test sample – fuel), and burning at lower pressures in reduced gravity. Specifically, it was found that the LBP for 3.2 mm diameter Inconel® 718 and 316 stainless steel test samples decreased by 50% from 3.45 MPa (500 psia) in normal gravity to 1.72 MPa (250 psia) in reduced gravity for the Inconel® 718, and 25% from 3.45 MPa (500 psia) in normal gravity to 2.76 MPa (400 psia) in reduced gravity for the 316 stainless steel. The average RRMI increased by factors of 2.2 (27.2 mm/s in 2.24 MPa (325 psia) oxygen in reduced gravity compared to 12.8 mm/s in 4.48 MPa (650 psia) oxygen in normal gravity) for the Inconel® 718 and 1.6 (15.0 mm/s in 2.76 MPa (400 psia) oxygen in reduced gravity compared to 9.5 mm/s in 5.17 MPa (750 psia) oxygen in normal gravity) for the 316 stainless steel. Reasons for the increased flammability of metallic materials in reduced gravity compared to normal gravity are discussed, based upon the observations made during reduced gravity testing and previous work. Finally, the implications (for fire safety and engineering applications) of these results are presented and discussed, in particular, examining methods for mitigating the risk of a fire in reduced gravity.

Preventing injuries on a state-wide basis : researchers and parliamentary committees are partners in turning injury prevention and safety research into practice and policy

Context: Parliamentary committees established in Westminster parliaments, such as Queensland, provide a cross-party structure that enables them to recommend policy and legislative changes that may otherwise be difficult for one party to recommend. The overall parliamentary committee process tends to be more cooperative and less adversarial than the main chamber of parliament and, as a result, this process permits parliamentary committees to make recommendations more on the available research evidence and less on political or party considerations. Objectives: This paper considers the contributions that parliamentary committees in Queensland have made in the past in the areas of road safety, drug use as well as organ and tissue donation. The paper also discusses the importance of researchers actively engaging with parliamentary committees to ensure the best evidence based policy outcomes. Key messages: In the past, parliamentary committees have successfully facilitated important safety changes with many committee recommendations based on research results. In order to maximise the benefits of the parliamentary committee process it is essential that researchers inform committees about their work and become key stakeholders in the inquiry process. Researchers can keep committees informed by making submissions to their inquiries, responding to requests for information and appearing as witnesses at public hearings. Researchers should emphasise the key findings and implications of their research as well as considering the jurisdictional implications and political consequences. It is important that researchers understand the differences between lobbying and providing informed recommendations when interacting with committees. Discussion and conclusions: Parliamentary committees in Queensland have successfully assisted in the introduction of evidence based policy and legislation. In order to present best practice recommendations, committees rely on the evidence presented to them including the results of researchers. Actively engaging with parliamentary committees will help researchers to turn their results into practice with a corresponding decrease in injuries and fatalities. Developing an understanding of parliamentary committees, and the typical inquiry process used by these committees, will help researchers to present their research results in a manner that will encourage the adoption of their ideas by parliamentary committees, the presentation of these results as recommendations within the report and the subsequent enactment of the committee’s recommendations by the government.

Reactive image-based collision avoidance system for unmanned aircraft systems

Approximately 20 years have passed now since the NTSB issued its original recommendation to expedite development, certification and production of low-cost proximity warning and conflict detection systems for general aviation [1]. While some systems are in place (TCAS [2]), ¡¨see-and-avoid¡¨ remains the primary means of separation between light aircrafts sharing the national airspace. The requirement for a collision avoidance or sense-and-avoid capability onboard unmanned aircraft has been identified by leading government, industry and regulatory bodies as one of the most significant challenges facing the routine operation of unmanned aerial systems (UAS) in the national airspace system (NAS) [3, 4]. In this thesis, we propose and develop a novel image-based collision avoidance system to detect and avoid an upcoming conflict scenario (with an intruder) without first estimating or filtering range. The proposed collision avoidance system (CAS) uses relative bearing ƒÛ and angular-area subtended ƒê , estimated from an image, to form a test statistic AS C . This test statistic is used in a thresholding technique to decide if a conflict scenario is imminent. If deemed necessary, the system will command the aircraft to perform a manoeuvre based on ƒÛ and constrained by the CAS sensor field-of-view. Through the use of a simulation environment where the UAS is mathematically modelled and a flight controller developed, we show that using Monte Carlo simulations a probability of a Mid Air Collision (MAC) MAC RR or a Near Mid Air Collision (NMAC) RiskRatio can be estimated. We also show the performance gain this system has over a simplified version (bearings-only ƒÛ ). This performance gain is demonstrated in the form of a standard operating characteristic curve. Finally, it is shown that the proposed CAS performs at a level comparable to current manned aviations equivalent level of safety (ELOS) expectations for Class E airspace. In some cases, the CAS may be oversensitive in manoeuvring the owncraft when not necessary, but this constitutes a more conservative and therefore safer, flying procedures in most instances.

Sociopathic attitudes to road safety

Injuries and deaths due to unsafe driving practices are a substantial health and socioeconomic burden to the community. Young socially disadvantaged males who are involved in a lifestyle of risky behaviour, crime and motor vehicle accidents seem unaffected by educational campaigns to improve safer driving. The aim is to develop a driving and social behavioural profile that may explain the lack of effectiveness of road safety advertising and suggest ways to refine educational strategies to reduce the risky lifestyle and associated harms among those most vulnerable, the 15-25 year olds. The procedure involved a quantitative and qualitative analysis through questionnaires, surveys and focus groups involving a comparison of populations (n = 668) by age, gender and socioeconomic status in three discrete Australian sites. Information gathered included issues related to road safety awareness, knowledge of advertising, personal and peer group attitudes as well as driving and life style history. The results indicate that within the community a highly visible profile of strong anti-social road safety activities by an educationally and economically disadvantaged sub-culture exists and this group seem impervious to road safety advertising and education initiatives. As the overall unsafe driving and risky antisocial behaviour is significant among 15-25 year olds within the community the solution is seen to be community based. A long-term (five to ten year) program has been posited; promoting community partnerships through consultative and local action committees at all levels creating locally designed formal and informal educational and mutual support programs.

The role of cognitive and visual abilities as predictors in the Multifactorial Model of Driving Safety

Objective The current study evaluated part of the Multifactorial Model of Driving Safety to elucidate the relative importance of cognitive function and a limited range of standard measures of visual function in relation to the Capacity to Drive Safely. Capacity to Drive Safely was operationalized using three validated screening measures for older drivers. These included an adaptation of the well validated Useful Field of View (UFOV) and two newer measures, namely a Hazard Perception Test (HPT), and a Hazard Change Detection Task (HCDT). Method Community dwelling drivers (n = 297) aged 65–96 were assessed using a battery of measures of cognitive and visual function. Results Factor analysis of these predictor variables yielded factors including Executive/Speed, Vision (measured by visual acuity and contrast sensitivity), Spatial, Visual Closure, and Working Memory. Cognitive and Vision factors explained 83–95% of age-related variance in the Capacity to Drive Safely. Spatial and Working Memory were associated with UFOV, HPT and HCDT, Executive/Speed was associated with UFOV and HCDT and Vision was associated with HPT. Conclusion The Capacity to Drive Safely declines with chronological age, and this decline is associated with age-related declines in several higher order cognitive abilities involving manipulation and storage of visuospatial information under speeded conditions. There are also age-independent effects of cognitive function and vision that determine driving safety.

Intelligent computing and sensing for active safety on construction sites

On obstacle-cluttered construction sites where heavy equipment is in use, safety issues are of major concern. The main objective of this paper is to develop a framework with algorithms for obstacle avoidance and path planning based on real-time three-dimensional job site models to improve safety during equipment operation. These algorithms have the potential to prevent collisions between heavy equipment vehicles and other on-site objects. In this study, algorithms were developed for image data acquisition, real-time 3D spatial modeling, obstacle avoidance, and shortest path finding and were all integrated to construct a comprehensive collision-free path. Preliminary research results show that the proposed approach is feasible and has the potential to be used as an active safety feature for heavy equipment.