The prediction of flash evaporation in superheated fuel injections for automotive applications

In gasoline Port Fuel Injection (PFI) and Direct Injection (GDI) internal combustion engines, the liquid fuel might be injected into a gaseous ambient in a superheated state, resulting in flash boiling of the fuel. The importance to investigate and predict such a process is due to the influence it has on the liquid fuel atomization and vaporization and thus on combustion, with direct implications on engine performances and exhaust gas emissions. The topic of the present PhD research involves the numerical analysis of the behaviour of the superheated fuel during the injection process, in high pressure injection systems like the ones equipping GDI engines. Particular emphasis is on the investigation of the effects of the fuel superheating degree on atomization dynamics and spray characteristics. The present work is a look at the flash evaporation and flash boiling modeling, from an engineering point of view, addressed to keep the complex physics involved as simple as possible, however capturing the main characteristics of a superheated fuel injection.

Advanced lithium and lithium-ion rechargeable batteries for automotive applications

The worldwide demand for a clean and low-fuel-consuming transport promotes the development of safe, high energy and power electrochemical storage and conversion systems. Lithium-ion batteries (LIBs) are considered today the best technology for this application as demonstrated by the recent interest of automotive industry in hybrid (HEV) and electric vehicles (EV) based on LIBs. This thesis work, starting from the synthesis and characterization of electrode materials and the use of non-conventional electrolytes, demonstrates that LIBs with novel and safe electrolytes and electrode materials meet the targets of specific energy and power established by U.S.A. Department of Energy (DOE) for automotive application in HEV and EV. In chapter 2 is reported the origin of all chemicals used, the description of the instruments used for synthesis and chemical-physical characterizations, the electrodes preparation, the batteries configuration and the electrochemical characterization procedure of electrodes and batteries. Since the electrolyte is the main critical point of a battery, in particular in large- format modules, in chapter 3 we focused on the characterization of innovative and safe electrolytes based on ionic liquids (characterized by high boiling/decomposition points, thermal and electrochemical stability and appreciable conductivity) and mixtures of ionic liquid with conventional electrolyte. In chapter 4 is discussed the microwave accelerated sol–gel synthesis of the carbon- coated lithium iron phosphate (LiFePO 4 -C), an excellent cathode material for LIBs thanks to its intrinsic safety and tolerance to abusive conditions, which showed excellent electrochemical performance in terms of specific capacity and stability. In chapter 5 are presented the chemical-physical and electrochemical characterizations of graphite and titanium-based anode materials in different electrolytes. We also characterized a new anodic material, amorphous SnCo alloy, synthetized with a nanowire morphology that showed to strongly enhance the electrochemical stability of the material during galvanostatic full charge/discharge cycling. Finally, in chapter 6, are reported different types of batteries, assembled using the LiFePO 4 -C cathode material, different anode materials and electrolytes, characterized by deep galvanostatic charge/discharge cycles at different C-rates and by test procedures of the DOE protocol for evaluating pulse power capability and available energy. First, we tested a battery with the innovative cathode material LiFePO 4 -C and conventional graphite anode and carbonate-based electrolyte (EC DMC LiPF 6 1M) that demonstrated to surpass easily the target for power-assist HEV application. Given that the big concern of conventional lithium-ion batteries is the flammability of highly volatile organic carbonate- based electrolytes, we made safe batteries with electrolytes based on ionic liquid (IL). In order to use graphite anode in IL electrolyte we added to the IL 10% w/w of vinylene carbonate (VC) that produces a stable SEI (solid electrolyte interphase) and prevents the graphite exfoliation phenomenon. Then we assembled batteries with LiFePO 4 -C cathode, graphite anode and PYR 14 TFSI 0.4m LiTFSI with 10% w/w of VC that overcame the DOE targets for HEV application and were stable for over 275 cycles. We also assembled and characterized ―high safety‖ batteries with electrolytes based on pure IL, PYR 14 TFSI with 0.4m LiTFSI as lithium salt, and on mixture of this IL and standard electrolyte (PYR 14 TFSI 50% w/w and EC DMC LiPF 6 50% w/w), using titanium-based anodes (TiO 2 and Li 4 Ti 5 O 12 ) that are commonly considered safer than graphite in abusive conditions. The batteries bearing the pure ionic liquid did not satisfy the targets for HEV application, but the batteries with Li 4 Ti 5 O 12 anode and 50-50 mixture electrolyte were able to surpass the targets. We also assembled and characterized a lithium battery (with lithium metal anode) with a polymeric electrolyte based on poly-ethilenoxide (PEO 20 – LiCF 3 SO 3 +10%ZrO 2 ), which satisfied the targets for EV application and showed a very impressive cycling stability. In conclusion, we developed three lithium-ion batteries of different chemistries that demonstrated to be suitable for application in power-assist hybrid vehicles: graphite/EC DMC LiPF 6 /LiFePO 4 -C, graphite/PYR 14 TFSI 0.4m LiTFSI with 10% VC/LiFePO 4 -C and Li 4 T i5 O 12 /PYR 14 TFSI 50%-EC DMC LiPF 6 50%/LiFePO 4 -C. We also demonstrated that an all solid-state polymer lithium battery as Li/PEO 20 –LiCF 3 SO 3 +10%ZrO 2 /LiFePO 4 -C is suitable for application on electric vehicles. Furthermore we developed a promising anodic material alternative to the graphite, based on SnCo amorphous alloy.

Collaudo e analisi termografica di centraline elettroniche per sistemi automotive

Questa tesi affronta lo sviluppo di sistemi elettronici per il collaudo automatizzato di centraline elettroniche per sistemi automotive. Viene illustrato lo sviluppo di un simulatore per il collaudo basato su ambiente Labview. Inoltre, viene presentata un'analisi di fattibiltà del rilevamento di malfunzionamenti basata sull'elaborazione di immagini termografiche.

Comparative Analysis of Alternative Hybrid Systems for Automotive Applications

The main objective of this work was to investigate the impact of different hybridization concepts and levels of hybridization on fuel economy of a standard road vehicle where both conventional and non-conventional hybrid architectures are treated exactly in the same way from the point of view of overall energy flow optimization. Hybrid component models were developed and presented in detail as well as the simulations results mainly for NEDC cycle. The analysis was performed on four different parallel hybrid powertrain concepts: Hybrid Electric Vehicle (HEV), High Speed Flywheel Hybrid Vehicle (HSF-HV), Hydraulic Hybrid Vehicle (HHV) and Pneumatic Hybrid Vehicle (PHV). In order to perform equitable analysis of different hybrid systems, comparison was performed also on the basis of the same usable system energy storage capacity (i.e. 625kJ for HEV, HSF and the HHV) but in the case of pneumatic hybrid systems maximal storage capacity was limited by the size of the systems in order to comply with the packaging requirements of the vehicle. The simulations were performed within the IAV Gmbh - VeLoDyn software simulator based on Matlab / Simulink software package. Advanced cycle independent control strategy (ECMS) was implemented into the hybrid supervisory control unit in order to solve power management problem for all hybrid powertrain solutions. In order to maintain State of Charge within desired boundaries during different cycles and to facilitate easy implementation and recalibration of the control strategy for very different hybrid systems, Charge Sustaining Algorithm was added into the ECMS framework. Also, a Variable Shift Pattern VSP-ECMS algorithm was proposed as an extension of ECMS capabilities so as to include gear selection into the determination of minimal (energy) cost function of the hybrid system. Further, cycle-based energetic analysis was performed in all the simulated cases, and the results have been reported in the corresponding chapters.

Emotional design e genetica dello stile in campo automotive: studio qualitativo e quantitativo delle linee di carattere

La figura del designer detiene un ruolo chiave nella progettazione di un nuovo prodotto: a lui spetta l'importante compromesso fra scelte ingegneristiche, di mercato e di stile. Lo studio qui condotto analizza da un punto di vista qualitativo e quantitativo le linee di carattere che delineano il profilo base di un'autovettura, in riferimento al particolare segmento automobilistico ed al suo stile. In tal modo si vuole porre una base alla "genetica dello stile", ovvero la caratterizzazione matematica dello stile.

Automotive diesel engine transient operation: modeling, optimization and control

Traditionally, the study of internal combustion engines operation has focused on the steady-state performance. However, the daily driving schedule of automotive engines is inherently related to unsteady conditions. There are various operating conditions experienced by (diesel) engines that can be classified as transient. Besides the variation of the engine operating point, in terms of engine speed and torque, also the warm up phase can be considered as a transient condition. Chapter 2 has to do with this thermal transient condition; more precisely the main issue is the performance of a Selective Catalytic Reduction (SCR) system during cold start and warm up phases of the engine. The proposal of the underlying work is to investigate and identify optimal exhaust line heating strategies, to provide a fast activation of the catalytic reactions on SCR. Chapters 3 and 4 focus the attention on the dynamic behavior of the engine, when considering typical driving conditions. The common approach to dynamic optimization involves the solution of a single optimal-control problem. However, this approach requires the availability of models that are valid throughout the whole engine operating range and actuator ranges. In addition, the result of the optimization is meaningful only if the model is very accurate. Chapter 3 proposes a methodology to circumvent those demanding requirements: an iteration between transient measurements to refine a purpose-built model and a dynamic optimization which is constrained to the model validity region. Moreover all numerical methods required to implement this procedure are presented. Chapter 4 proposes an approach to derive a transient feedforward control system in an automated way. It relies on optimal control theory to solve a dynamic optimization problem for fast transients. From the optimal solutions, the relevant information is extracted and stored in maps spanned by the engine speed and the torque gradient.

Analisi e ottimizzazione di un container management system nel settore automotive: Il caso Robert Bosch GmbH.

Il presente elaborato descrive l’attività di progetto svolta durante il periodo di tirocinio presso la business unit “automotive technologies” della Robert Bosch GmbH: la Robert Bosch GmbH Branch in Italy che ha sede a Torino, e che si configura come fornitore di componenti per l’industria automotive. La funzione logistica è l’ufficio in cui si è svolta l’esperienza di tirocinio, che si è sviluppato nell’ambito del progetto di Container Management System. In particolare, è stato analizzato il sistema di gestione dei Returnable Packaging relativi ai componenti che vengono forniti agli stabilimenti dei clienti localizzati in Italia. L’elaborato è composto da due parti: una parte teorica e una parte pratica. La parte teorica espone gli strumenti teorici sui quali si fondano i contenuti sviluppati nella parte pratica. La parte pratica è volta a descrivere l’attività di progetto da un punto di vista strettamente operativo. Il primo capitolo illustra i motivi che hanno determinato l’avvio del progetto. Sono poi messi in evidenza quali sono gli obiettivi intermedi e finali che si intendono raggiungere, declinandoli in termini di organizzazione del lavoro. Sono qui esposte le basi teoriche del metodo utilizzato e della disciplina a cui si fa riferimento. Viene inoltre dato spazio alla trattazione di alcuni topic nell’ambito dei Returnable Packaging, approfondendo l’argomento per il settore automotive. Il secondo capitolo descrive la struttura organizzativa, i settori di business e le attività svolte dal gruppo Robert Bosch GmbH nel mondo e in Italia. Viene dato particolare rilievo alla sede di Torino ed alla divisione logistica di quest’ultima, in modo tale da descrivere il contesto entro il quale si sviluppa il progetto. Il capitolo presenta infine gli attori che operano nella catena logistica analizzata, descrivendone le attività svolte e caratterizzando la rete logistica studiata al fine di definire i confini entro i quali si sviluppa il progetto. Il terzo capitolo presenta l’analisi effettuata sul caso in esame, descrivendone le modalità operative per ciascuna fase. Il quarto capitolo presenta delle osservazioni sull’analisi effettuata, la validazione tecnico econimica delle soluzioni proposte e le considerazioni conclusive.

Analisi dell'introduzione di tecniche additive nel processo produttivo di airbox per il settore automotive

Analisi dell'introduzione di tecniche additive nel processo produttivo di airbox nel settore automotive, attraverso lo studio della tecnologia additiva e delle principali tecniche che ne fanno parte. Valutazione delle capacità delle tecniche additive per confrontarle con tecniche di produzione tradizionale, attraverso l'analisi prestazionale, dei costi e dei tempi di produzione.

Analysis and partial solutions of security problems in automotive environments

Questo scritto mira a fare una panoramica dei problemi legati alla sicurezza della comunicazione tra componenti interne dei veicoli e delle soluzioni oggigiorno disponibili. Partendo con una descrizione generale del circuito interno dell’auto analizzeremo i suoi punti di accesso e discuteremo i danni prodotti dalla sua manomissione illecita. In seguito vedremo se ´è possibile prevenire tali attacchi dando un’occhiata alle soluzioni disponibili e soffermandoci in particolare sui moduli crittografici e le loro applicazioni. Infine presenteremo l’implementazione pratica di un protocollo di autenticazione tra ECUs e una dimostrazione matematica della sua sicurezza.

Molle a disco conico in materiale composito per applicazioni automotive: primo dimensionamento e realizzazione

Lo scopo del seguente elaborato è porre le basi per il dimensionamento, e la successiva realizzazione, di molle a disco conico costruite con materiali compositi per applicazioni automotive, che costituiscano una possibile alternativa alle comuni molle elicoidali in materiali metallici. I vantaggi principali riguardano un risparmio in termini di peso ed un miglioramento del comportamento a fatica. Successivamente ad una introduzione sulle teorie analitiche e numeriche applicabili a tali tipologie di molle, è stata effettuata un'analisi volta all'individuazione dei parametri geometrici principali che regolano il comportamento delle molle a tazza, a cui fa seguito la stesura di una procedura per il dimensionamento preliminare. Sono, in seguito, stati riportati i cenni teorici relativi alle configurazioni di montaggio, alla definizione degli attriti, delle tensioni, alla valutazione dei carichi affaticanti e delle tipologie di carico. I risultati ottenuti nel dimensionamento sono stati infine utilizzati per realizzare alcuni prototipi funzionali di elementi di molle a tazza in carbonio con tecnologia di laminazione manuale e successiva fase di polimerizzazione in forno. Tali provini sono stati analizzati per valutare le problematiche sorte durante la produzione, quali mancata compattazione delle lamine, eccessi di resina e formazione di vuoti, proponendo infine possibili soluzioni e miglioramenti.

Caratterizzazione meccanica di un incollaggio acciaio-CFRP per applicazione automotive

Nella tesi viene caratterizzato meccanicamente un giunto incollato acciaio-CFRP usato nella produzione di un componente automotive. In particolare viene analizzata l'influenza data da trattamenti termici di invecchiamento e sono messe a confronto diverse tipologie di adesivi.

Accelerometer based measurements of combustion in an automotive turbocharged diesel engine

The capability to detect combustion in a diesel engine has the potential of being an important control feature to meet increasingly stringent emission regulations, develop alternative combustion strategies, and use of biofuels. In this dissertation, block mounted accelerometers were investigated as potential feedback sensors for detecting combustion characteristics in a high-speed, high pressure common rail (HPCR), 1.9L diesel engine. Accelerometers were positioned in multiple placements and orientations on the engine, and engine testing was conducted under motored, single and pilot-main injection conditions. Engine tests were conducted at varying injection timings, engine loads, and engine speeds to observe the resulting time and frequency domain changes of the cylinder pressure and accelerometer signals. The frequency content of the cylinder pressure based signals and the accelerometer signals between 0.5 kHz and 6 kHz indicated a strong correlation with coherence values of nearly 1. The accelerometers were used to produce estimated combustion signals using the Frequency Response Functions (FRF) measured from the frequency domain characteristics of the cylinder pressure signals and the response of the accelerometers attached to the engine block. When compared to the actual combustion signals, the estimated combustion signals produced from the accelerometer response had Root Mean Square Errors (RMSE) between 7% and 25% of the actual signals peak value. Weighting the FRF’s from multiple test conditions along their frequency axis with the coherent output power reduced the median RMSE of the estimated combustion signals and the 95th percentile of RMSE produced from each test condition. The RMSE’s of the magnitude based combustion metrics including peak cylinder pressure, MPG, peak ROHR, and work estimated from the combustion signals produced by the accelerometer responses were between 15% and 50% of their actual value. The MPG measured from the estimated pressure gradient shared a direct relationship to the actual MPG. The location based combustion metrics such as the location of peak values and burn durations were capable of RMSE measurements as low as 0.9°. Overall, accelerometer based combustion sensing system was capable of detecting combustion and providing feedback regarding the in cylinder combustion process