A comprehensive study of interference and clearance fit pins in large plates

Pin joints in structures are designed for interference, push or clearance fits. That is, the diameter of the pin is made greater than, equal to or less than the hole diameter. Consider an interference fit pin in a plate subjected to a continuously increasing in-plane load.

Queuing Models for Estimating Aircraft Fleet Availability

The availability of a small fleet of aircraft in a flying-base, repair-depot combination is modeled and studied. First, a deterministic flow model relates parameters of interest and represents the state-of-the art in the planning of such systems. Second, a cyclic queue model shows the effect of the principal uncertainties in operation and repair and shows the consequent decrease in the availability of aircraft at the flying-base. Several options such as increasing fleet size, investments in additional repair facilities, or building reliability and maintainability into the individual aircraft during its life-cycle are open for increasing the availability. A life-cycle cost criterion brings out some of these features. Numerical results confirm Rose's prediction that there exists a minimal cost combination of end products and repair-depot capability to achieve a prescribed operational availability.

Rapid synthetic routes to prepare LiNi1/3Mn1/3Co1/3O2 as a high voltage, high-capacity Li-ion battery cathode material

LiNi1/3Mn1/3Co1/3O2, a high voltage and high-capacity cathode material for Li-ion batteries, has been synthesized by three different rapid synthetic methods. viz. nitrate-melt decomposition, combustion and sol-gel methods. The first two methods are ultra rapid and a time period as small as 15 min is sufficient to prepare nano-crystalline LiNi1/3Mn1/3Co1/3O2. The processing parameters in obtaining the best performing materials are optimized for each process and their electrochemical performance is evaluated in Li-ion cells. The combustion-derived LiNi1/3Mn1/3Co1/3O2 sample exhibits large extent of cation mixing (10%) while the other two methods yield LiNi1/3Mn1/3Co1/3O2 with cation mixing <5%. LiNi1/3Mn1/3Co1/3O2 prepared by nitrate-melt decomposition method exhibits superior performance as Li-ion battery cathode material.

Synthesis of wurtzite-phase ZnS nanocrystal and its optical properties

The wurtzite phase of ZnS nanocrystal has been prepared by annealing in 200-600 degrees C temperature range, its cubic phase of 2-3 nm size. prepared through soft chemical method. Results of isochronal experiments of 2 h at different temperatures indicate that visible transformation to wurtzite from cubic ZnS appears at a temperature of 400 degrees C, which is about three times smaller than that of bulk ZnS phase transition temperature. The phases, nanostructures, and optical absorption characteristics are obtained through X-ray diffraction. transmission electron microscopy, and UV-visible absorption spectroscopy. A stable and green photoluminescence emission peaked at 518 nm is observed from the 600 degrees C annealed samples, under ultraviolet light excitation.

Review of continuum, finite element and hybrid techniques in the analysis of stress concentrations in structures

When a uniform flow of any nature is interrupted, the readjustment of the flow results in concentrations and rare-factions, so that the peak value of the flow parameter will be higher than that which an elementary computation would suggest. When stress flow in a structure is interrupted, there are stress concentrations. These are generally localized and often large, in relation to the values indicated by simple equilibrium calculations. With the advent of the industrial revolution, dynamic and repeated loading of materials had become commonplace in engine parts and fast moving vehicles of locomotion. This led to serious fatigue failures arising from stress concentrations. Also, many metal forming processes, fabrication techniques and weak-link type safety systems benefit substantially from the intelligent use or avoidance, as appropriate, of stress concentrations. As a result, in the last 80 years, the study and and evaluation of stress concentrations has been a primary objective in the study of solid mechanics. Exact mathematical analysis of stress concentrations in finite bodies presents considerable difficulty for all but a few problems of infinite fields, concentric annuli and the like, treated under the presumption of small deformation, linear elasticity. A whole series of techniques have been developed to deal with different classes of shapes and domains, causes and sources of concentration, material behaviour, phenomenological formulation, etc. These include real and complex functions, conformal mapping, transform techniques, integral equations, finite differences and relaxation, and, more recently, the finite element methods. With the advent of large high speed computers, development of finite element concepts and a good understanding of functional analysis, it is now, in principle, possible to obtain with economy satisfactory solutions to a whole range of concentration problems by intelligently combining theory and computer application. An example is the hybridization of continuum concepts with computer based finite element formulations. This new situation also makes possible a more direct approach to the problem of design which is the primary purpose of most engineering analyses. The trend would appear to be clear: the computer will shape the theory, analysis and design.

A study of interaction between two He+ ions in terms of the electronic forces

The potential energy curve of the He2+2 system dissociating into two He+ ions is examined in terms of the electronic force exerted on each nucleus as a function of the internuclear separation. The results are compared with the process of bond-formation in H2 from the separated atoms.

Sequence distribution in Acrylonitrile-methylacrylate random copolymers by N.M.R spectroscopy

The sequence distribution studies on the acrylonitrile-methylmethacrylate copolymer of high methylmethacrylate (M) content (30%aks observed for methixy and a-methyl protons. The presence of MMM type of triad sequences is indicated by the pattern of a-methyl protons.

The perturbational treatment of the process of hydrogen abstraction by ketones

The change in energy during hydrogen abstraction by ketones is estimated for different electronic states as a function of the intermolecular orbital overlap employing perturbation theory. The results suggest that ketones preferentially undergo the in-plane reaction and abstract a hydrogen atom in their triplet nπ* state. For ketones where the triplet ππ* state lies below the triplet nπ* state, hydrogen abstraction can take place in the ππ* state owing to the crossing of the zero order reaction surfaces of the nπ* and ππ* states.

Influence of adhesive non-linearities on the performance and optimal length of adhesive bonded joints

An analytical study for the static strength of adhesive lap joints is presented. The earlier solutions of Volkersen [i], DeBruyne[2] and others were limited to linear adhesives. The influence of adhesive non-linearity was first considered by Grimes' et al[3] and Dickson et al [4]. Recently Hart-Smith[5] successfully introduced elastic-plastic behaviour of the adhesive. In the present study the problem is formulated for general non-linear adhesive behaviour and an efficient numerical algorithm is written for the solution. Bilinear and trilinear models for the nonlinearity yield closed form analytical solutions.

Dilute solution properties of methyl methacrylate�acrylonitrile copolymer (MA1)

This paper deals with studies on the dilute solution properties of methyl methacrylate�acrylonitrile copolymer of 0.289 mole fraction (mf) of acrylonitrile composition. Mark�Houwink parameters for this copolymer have been evaluated in acetonitrile (MeCN), 2-butanone (MEK), dimethylformamide (DMF) and γ-butyrolactone (γ-BL). The solvent power is found to be in the order of MEK < MeCN < DMF < γ-BL at 30°C. Herein, probably for the first time, the steric factor for the copolymer is found to be lower than that for the parent homopolymers and the excess interaction parameter, �AB is found to be negative. This probably suggests that the units are compatible to each other.

Temperature influence on the excess interaction parameter of styrene-methyl methacrylate copolymer

Intrinsic viscosity data for polystyrene, poly(methyl methacrylate) and styrene-methyl methacrylate copolymer of azeotropic composition have been used to evaluate the excess interaction parameters at different temperatures in γ-butyrolactone and dimethylformamide. It is found that these values are positive and show a negligible increase with increase in temperature, indicating therefore that the hetero-contact interactions are not influenced by temperature, contrary to the results obtained by Dondos and Benoit for the same copolymer system in p-xylene and iso-amyl acetate.

Carbon-Supported Pt-TiO2 as a Methanol-Tolerant Oxygen-Reduction Catalyst for DMFCs

Carbon-supported Pt-TiO2 (Pt-TiO2/C) catalysts with varying at. wt ratios of Pt to Ti, namely, 1:1, 2:1, and 3:1, are prepared by the sol-gel method. The electrocatalytic activity of the catalysts toward oxygen reduction reaction (ORR), both in the presence and absence of methanol, is evaluated for application in direct methanol fuel cells (DMFCs). The optimum at. wt ratio of Pt to Ti in Pt-TiO2/C is established by fuel cell polarization, linear sweep voltammetry, and cyclic voltammetry studies. Pt-TiO2/C heattreated at 750 degrees C with Pt and Ti in an at. wt ratio of 2:1 shows enhanced methanol tolerance, while maintaining high catalytic activity toward ORR. The DMFC with a Pt-TiO2/C cathode catalyst exhibits an enhanced peak power density of 180 mW/cm(2) in contrast to the 80 mW/cm(2) achieved from the DMFC with carbon-supported Pt catalyst while operating under identical conditions. Complementary data on the influence of TiO2 on the crystallinity of Pt, surface morphology, and particle size, surface oxidation states of individual constituents, and bulk and surface compositions are also obtained by powder X-ray diffraction, scanning and transmission electron microscopy, X-ray photoelectron spectroscopy, energy dispersive analysis by X-ray, and inductively coupled plasm optical emission spectrometry.

An ethnobotanical study of traditional anti-inflammatory plants used by the Lohit community of Arunachal Pradesh, India

Aim of the study: Most people especially in rural areas depend on herbal medicines to treat many diseases including inflammation-related ailments such as rheumatism, muscle swelling, cut wound, accidental bone fracture, insect bites, pains and burn by fire and hot water. The objectives of this study were: to catalog ethno-medicinal plants of Lohit community, ecological status, indigenous folk medicinal uses, morphological parts used and to determine their reported pharmacological studies. Materials and methods: The ethnobotanical information on traditional medicinal plants exclusively used for management of inflammation-related ailments by the Khampti community of Arunachal Pradesh, India was based on first-hand field survey work through semi-structured interviews. Results and conclusion: A total of 34 species in 32 genera and 22 families were encountered during the field survey. Botanical families such as Asteraceae, Euphorbiaceae, Zingiberaceae and Lamiaceae were represented by the highest numbers of species reported in this study. Thirteen plant species, namely: Bombax ceiba, Canarium strictum, Chloranthus erectus, Xanthium indicum, Lycopodium clavatum, Coleus blumei, Batrachospermum atrum, Chlorella vulgaris, Marchantia palmata, Marchantia polymorpha, Eria pannea, Sterculia villosa and Alpinia galanga are reported for the first time for the treatment of inflammation-related diseases.

Modeling of Convection and Macrosegregation through Appropriate Consideration of Multiphase/Multiscale Phenomena during Alloy Solidification

Solidification processes are complex in nature, involving multiple phases and several length scales. The properties of solidified products are dictated by the microstructure, the mactostructure, and various defects present in the casting. These, in turn, are governed by the multiphase transport phenomena Occurring at different length scales. In order to control and improve the quality of cast products, it is important to have a thorough understanding of various physical and physicochemical phenomena Occurring at various length scales. preferably through predictive models and controlled experiments. In this context, the modeling of transport phenomena during alloy solidification has evolved over the last few decades due to the complex multiscale nature of the problem. Despite this, a model accounting for all the important length scales directly is computationally prohibitive. Thus, in the past, single-phase continuum models have often been employed with respect to a single length scale to model solidification processing. However, continuous development in understanding the physics of solidification at various length scales oil one hand and the phenomenal growth of computational power oil the other have allowed researchers to use increasingly complex multiphase/multiscale models in recent. times. These models have allowed greater understanding of the coupled micro/macro nature of the process and have made it possible to predict solute segregation and microstructure evolution at different length scales. In this paper, a brief overview of the current status of modeling of convection and macrosegregation in alloy solidification processing is presented.