Two Boats in the Mediterranean and their Unfortunate Encounters with Europe’s Policies towards People on the Move. CEPS Liberty and Security in Europe No. 48, 20 July 2012

Two stark reminders of the difficulties that people on the move encounter in the Mediterranean have been grabbing headlines recently: the so-called ‘left-to-die’ boat report and the ground-breaking Hirsi judgment. These two instances present the worst of both worlds: the first concerns a migrant boat that was ignored altogether, resulting in many deaths, whereas the second concerns a migrant boat being intercepted but subsequently dealt with in a way that contradicts Europe’s human rights standards. These two cases are neither isolated nor incidental. Instead they are of wider concern to the EU and reminders of structural deficiencies in Europe’s approach to people on the move in the Mediterranean. This paper identifies those cross-cutting deficiencies and proposes recommendations to correct them.

Near infrared reflectance spectroscopy (NIRS) to predict biological parameters of maize silage: effects of particle comminution, oven drying temperature and the presence of residual moisture

Maize silage nutritive quality is routinely determined by near infrared reflectance spectroscopy (NIRS). However, little is known about the impact of sample preparation on the accuracy of the calibration to predict biological traits. A sample population of 48 maize silages representing a wide range of physiological maturities was used in a study to determine the impact of different sample preparation procedures (i.e., drying regimes; the presence or absence of residual moisture; the degree of particle comminution) on resultant NIR prediction statistics. All silages were scanned using a total of 12 combinations of sample pre-treatments. Each sample preparation combination was subjected to three multivariate regression techniques to give a total of 36 predictions per biological trait. Increased sample preparations procedure, relative to scanning the unprocessed whole plant (WP) material, always resulted in a numerical minimisation of model statistics. However, the ability of each of the treatments to significantly minimise the model statistics differed. Particle comminution was the most important factor, oven-drying regime was intermediate, and residual moisture presence was the least important. Models to predict various biological parameters of maize silage will be improved if material is subjected to a high degree of particle comminution (i.e., having been passed through a 1 mm screen) and developed on plant material previously dried at 60 degrees C. The extra effort in terms of time and cost required to remove sample residual moisture cannot be justified. (c) 2005 Elsevier B.V. All rights reserved.

Onset of germinability, desiccation tolerance and hardseededness in developing seeds of Peltophorum pterocarpum (DC) K. Heyne (Caesalpinioideae)

In the hot and dry conditions in which seeds of the tree legume Peltophorum pterocarpum develop and mature in Vietnam, seed moisture content declined rapidly on the mother plant from 87% at 42 d after flowering (DAF) to 15% at 70 DAF. Dry weight of the pods attained a maximum value at about 42 DAF, but seed mass maturity (i.e. the end of the seed-filling phase) occurred at about 62 DAF, at which time seed moisture content was about 45-48%. The onset of the ability of freshly collected seeds to germinate (in 63-d tests at 28-34degreesC) occurred at 42 DAF, i.e. about 20 d before mass maturity. Full germination (98%) was attained at 70 DAF, i.e. at about 8 d after mass maturity. Thereafter, germination of fresh seeds declined, due to the imposition of a hard seed coat. Tolerance of desiccation to 10% moisture content was first detected at 56 DAF and was complete within the seed population by 84 DAF, i.e. about 22 d after mass maturity. Hardseededness began to be induced when seeds were dried to about 15% moisture content and below, with a negative logarithmic relation between hardseededness and moisture content below this value.

Peroxydisulfate in MCM-48 silicas: powerful and clean materials for the removal of toxic gases

Sodium persulfate introduced into ordered MCM-48 silicas is described. The resulting materials are compared with existing activated carbon-based systems and MCM-48 containing transition metals such as Cu(II) and Cr(VI) for the decomposition of hydrogen cyanide and cyanogen. MCM-48 materials containing sodium persulfate alone improve on the protection offered by benchmark activated carbon systems and MCM-48 materials containing Cu(II) and Cr(VI), without the health risks associated with these metal ions.