Introduction of the T-10 static line parachuting capability to the NH90 helicopter

The purpose of this study was to investigate the suitability of the Finnish Defence Forces’ NH90 helicopter for parachuting operations with the T-10 static line parachute system. The work was based on the Army Command’s need to compensate for the reduction in the outsourced flight hours for the military static line parachuting training. The aim of the research was to find out the procedures and limitations with which the NH90 IOC+ or FOC version helicopter could be used for static line parachutist training with the T- 10B/MC1-1C parachutes. The research area was highly complicated and non-linear. Thus analytical methods could not be applied with sufficient confidence, even with present-day computing power. Therefore an empirical research method was selected, concentrating on flight testing supported with literature study and some calculated estimations. During three flights and 4.5 flight hours in Utti, Finland on 17−20 September 2012, a total of 44 parachute drops were made. These consisted of 16 dummy drops and 28 paratrooper jumps. The test results showed that when equipped with the floor mounted PASI-1 anchor line, the deflector bar of the NHIndustries’ Parachuting Kit and Patria’s floor protection panels the Finnish NH90 variant could be safely used for T-10B/MC1-1C static line parachuting operations from the right cabin door at airspeed range of 50−80 KIAS (∼90–150 km/h). The ceiling mounted anchor lines of the NHI’s Parachuting Kit were not usable with the T-10 system. This was due to the static lines’ unsafe behaviour in slipstream when connected to the cabin ceiling level. In conclusion, the NH90 helicopter can be used to meet the Army Command’s requirement for an additional platform for T-10 static line parachutist training. Material dropping, the effect of additional equipment and jumping from the rear ramp should be further studied.

Novel technology for preparation of optically active chemicals

Asymmetric synthesis using modified heterogeneous catalysts has gained lots of interest in the production of optically pure chemicals, such as pharmaceuticals, nutraceuticals, fragrances and agrochemicals. Heterogeneous modified catalysts capable of inducing high enantioselectivities are preferred in industrial scale due to their superior separation and handling properties. The topic has been intensively investigated both in industry and academia. The enantioselective hydrogenation of ethyl benzoylformate (EBF) to (R)-ethyl mandelate over (-)-cinchonidine (CD)-modified Pt/Al2O3 catalyst in a laboratory-scale semi-batch reactor was studied as a function of modifier concentration, reaction temperature, stirring rate and catalyst particle size. The main product was always (R)-ethyl mandelate while small amounts of (S)-ethyl mandelate were obtained as by product. The kinetic results showed higher enantioselectivity and lower initial rates approaching asymptotically to a constant value as the amount of modifier was increased. Additionally, catalyst deactivation due to presence of impurities in the feed was prominent in some cases; therefore activated carbon was used as a cleaning agent of the raw material to remove impurities prior to catalyst addition. Detailed characterizations methods (SEM, EDX, TPR, BET, chemisorption, particle size distribution) of the catalysts were carried out. Solvent effects were also studied in the semi-batch reactor. Solvents with dielectric constant (e) between 2 and 25 were applied. The enantiomeric excess (ee) increased with an increase of the dielectric coefficient up to a maximum followed by a nonlinear decrease. A kinetic model was proposed for the enantioselectivity dependence on the dielectric constant based on the Kirkwood treatment. The non-linear dependence of ee on (e) successfully described the variation of ee in different solvents. Systematic kinetic experiments were carried out in the semi-batch reactor. Toluene was used as a solvent. Based on these results, a kinetic model based on the assumption of different number of sites was developed. Density functional theory calculations were applied to study the energetics of the EBF adsorption on pure Pt(1 1 1). The hydrogenation rate constants were determined along with the adsorption parameters by non-linear regression analysis. A comparison between the model and the experimental data revealed a very good correspondence. Transient experiments in a fixed-bed reactor were also carried out in this work. The results demonstrated that continuous enantioselective hydrogenation of EBF in hexane/2-propanol 90/10 (v/v) is possible and that continuous feeding of (-)-cinchonidine is needed to maintain a high steady-state enantioselectivity. The catalyst showed a good stability and high enantioselectivity was achieved in the fixed-bed reactor. Chromatographic separation of (R)- and (S)-ethyl mandelate originating from the continuous reactor was investigated. A commercial column filled with a chiral resin was chosen as a perspective preparative-scale adsorbent. Since the adsorption equilibrium isotherms were linear within the entire investigated range of concentrations, they were determined by pulse experiments for the isomers present in a post-reaction mixture. Breakthrough curves were measured and described successfully by the dispersive plug flow model with a linear driving force approximation. The focus of this research project was the development of a new integrated production concept of optically active chemicals by combining heterogeneous catalysis and chromatographic separation technology. The proposed work is fundamental research in advanced process technology aiming to improve efficiency and enable clean and environmentally benign production of enantiomeric pure chemicals.

ORCiD – Membership and implementation at Chalmers University of Technology

Poster at Open Repositories 2014, Helsinki, Finland, June 9-13, 2014

Bridging the digital divide in developing countries: The role of mobile technology in bridging the digital divide

This thesis investigates how mobile technology usage could help to bring Information and communication technologies (ICT) to the people in developing countries. Some people in developing countries have access to use ICT while other people do not have such opportunity. This digital divide among people is present in many developing countries where computers and the Internet are difficult to access. The Internet provides information that can increase productivity and enable markets to function more efficiently. The Internet reduces information travel time and provides more efficient ways for firms and workers to operate. ICT and the Internet can provide opportunities for economic growth and productivity in developing countries. This indicates that it is very important to bridge the digital divide and increase Internet connections in developing countries. The purpose of this thesis is to investigate how can mobile technology and mobile services help to bridge the digital divide in developing countries. Theoretical background of this thesis consists of a collection of articles and reports. Theoretical material was gathered by going through literature on the digital divide, mobile technology and mobile application development. The empirical research was conducted by sending a questionnaire by email to a selection of application developers located in developing countries. The questionnaire’s purpose was to gather qualitative information concerning mobile application development in developing countries. This thesis main result suggests that mobile phones and mobile technology usage can help to bridge the digital divide in developing countries. This study finds that mobile technology provides one of the best tools that can help to bridge the digital divide in developing countries. Mobile technology can bring affordable ICT to people who do not have access to use computers. Smartphones can provide Internet connection, mobile services and mobile applications to a rapidly growing number of mobile phone users in developing countries. New low-cost smartphones empower people in developing countries to have access to information through the Internet. Mobile technology has the potential to help to bridge the digital divide in developing countries where a vast amount of people own mobile phones.

A conceptual and practical overview of cDNA microarray technology: implications for basic and clinical sciences

cDNA microarray is an innovative technology that facilitates the analysis of the expression of thousands of genes simultaneously. The utilization of this methodology, which is rapidly evolving, requires a combination of expertise from the biological, mathematical and statistical sciences. In this review, we attempt to provide an overview of the principles of cDNA microarray technology, the practical concerns of the analytical processing of the data obtained, the correlation of this methodology with other data analysis methods such as immunohistochemistry in tissue microarrays, and the cDNA microarray application in distinct areas of the basic and clinical sciences.

Determination of trans-10-hydroxy-2-decenoic acid (10-HDA) in royal jelly from São Paulo State, Brazil

The 10-HDA content in Brazilian samples (São Paulo State) of royal jelly (RJ) was analyzed using an HPLC method based on the work by BLOODWORTH et al. [2]. The chromatographic conditions were: isocratic system, reversed phase C18-H column, auto sampler, diode array UV-VIS detector adjusted to 225nm, mobile phase composed by methanol/water (45:55) at pH= 2.5 adjusted with phosphoric acid; a-naphtol was used as internal standard, and the running time was 30min. By statistical analysis of the results, the 10-HDA contents of the samples analyzed seem to have two ranges: 1.8% and 3% (w/w), that would be useful to qualify the RJ. This is the first data regarding 10-HDA content of Brazilian RJ.

Development of an alternative technology for the oyster mushroom production using liquid inoculum

Pleurotus ostreatus, worldwide known as oyster mushroom, was cultivated in banana straw using inocula produced by two different processes - liquid inoculum and the traditionally used solid inoculum. Different ratios (5, 10, 15, and 20%) were tested. Biological efficiency, yield, productivity, organic matter loss, and moisture of fruiting bodies as well as physical-chemical characteristics of banana straw were studied. Significant differences were observed for cellulose, lignin, and hemicellulose content between one and two harvests for both solid and liquid inocula. It was observed that P. ostreatus growth promoted higher degradation of lignin (80.36%), followed by hemicellulose (78.64%) and cellulose (60.37%). Significant differences between one and two harvests were also observed for the production parameters (biological efficiency and yield) for both kinds of inocula, liquid and solid. However, significant differences in productivity between harvests were observed only for solid inoculum.

Jaboticaba peel for jelly preparation: an alternative technology

The peel of jaboticaba is attractive regarding its nutritional, functional and sensory aspects. However, its use for consumption is still restricted due to the need of technological development in order to obtain processed preparations for its inclusion in the human diet. The purpose of this study was to produce jelly using the peel of jaboticaba and to characterize it chemically and sensorially. Diferent formulations were prepared, all with 50% of sugar and with different proportions of peel, pulp and pectin. The formulations, which were tested for preference, were the following: F1a (80% of peel, 20% of pulp and 0.5% of pectin) and F3b (50% of peel, 50% pulp and 1.0% of pectin). These formulations showed chemical composition of 216.44 mg phenolic compounds, 148.00 mg gallic acid.100 g-1, 10.42 mg flavonoids, and 12.10 mg catechin.100 g-1, and 80% acceptability index. The peel presented higher levels of nutrients than the pulp, especially as source of fiber, carbohydrates and natural pigments. Results indicated the feasibility of technological nutritional harnessing of the jaboticaba peel in obtaining jelly. The results also indicated good sensory and nutritional characteristics, acceptability, and antioxidant properties of natural pigments.

Suitability of LiDAR technology for forest inventory in Russia

LiDAR is an advanced remote sensing technology with many applications, including forest inventory. The most common type is ALS (airborne laser scanning). The method is successfully utilized in many developed markets, where it is replacing traditional forest inventory methods. However, it is innovative for Russian market, where traditional field inventory dominates. ArboLiDAR is a forest inventory solution that engages LiDAR, color infrared imagery, GPS ground control plots and field sample plots, developed by Arbonaut Ltd. This study is an industrial market research for LiDAR technology in Russia focused on customer needs. Russian forestry market is very attractive, because of large growing stock volumes. It underwent drastic changes in 2006, but it is still in transitional stage. There are several types of forest inventory, both with public and private funding. Private forestry enterprises basically need forest inventory in two cases – while making coupe demarcation before timber harvesting and as a part of forest management planning, that is supposed to be done every ten years on the whole leased territory. The study covered 14 companies in total that include private forestry companies with timber harvesting activities, private forest inventory providers, state subordinate companies and forestry software developer. The research strategy is multiple case studies with semi-structured interviews as the main data collection technique. The study focuses on North-West Russia, as it is the most developed Russian region in forestry. The research applies the Voice of the Customer (VOC) concept to elicit customer needs of Russian forestry actors and discovers how these needs are met. It studies forest inventory methods currently applied in Russia and proposes the model of method comparison, based on Multi-criteria decision making (MCDM) approach, mainly on Analytical Hierarchy Process (AHP). Required product attributes are classified in accordance with Kano model. The answer about suitability of LiDAR technology is ambiguous, since many details should be taken into account.

Towards a contextual understanding of B2B salespeople's selling competencies – An exploratory study among purchasing decision-makers of internationally-oriented technology firms

ABSTRACT Towards a contextual understanding of B2B salespeople’s selling competencies − an exploratory study among purchasing decision-makers of internationally-oriented technology firms The characteristics of modern selling can be classified as follows: customer retention and loyalty targets, database and knowledge management, customer relationship management, marketing activities, problem solving and system selling, and satisfying needs and creating value. For salespeople to be successful in this environment, they need a wide range of competencies. Salespeople’s selling skills are well documented in seller side literature through quantitative methods, but the knowledge, skills and competencies from the buyer’s perspective are under-researched. The existing research on selling competencies should be broadened and updated through a qualitative research perspective due to the dynamic nature and the contextual dependence of selling competencies. The purpose of the study is to increase understanding of the professional salesperson’s selling competencies from the industrial purchasing decision- makers’ viewpoint within the relationship selling context. In this study, competencies are defined as sales-related knowledge and skills. The scope of the study includes goods, materials and services managed by a company’s purchasing function and used by an organization on a daily basis. The abductive approach and ‘systematic combining’ have been applied as a research strategy. In this research, data were generated through semi- structured, person-to-person interviews and open-ended questions. The study was conducted among purchasing decision-makers in the technology industry in Finland. The branches consisted of the electronics and electro-technical industries and the mechanical engineering and metals industries. A total of 30 companies and one purchasing decision-maker from each company were purposively chosen for the sampling. The sample covers different company sizes based on their revenues, their differing structures – varying from public to family companies –that represent domestic and international ownerships. Before analyzing the data, they were organized by the purchasing orientations of the buyers: the buying, procurement or supply management orientation. Thematic analysis was chosen as the analysis method. After analyzing the data, the results were contrasted with the theory. There was a continuous interaction between the empirical data and the theory. Based on the findings, a total of 19 major knowledge and skills were identified from the buyers’ perspective. The specific knowledge and skills from the viewpoint of customers’ prevalent purchasing orientations were divided into two categories, generic and contextual. The generic knowledge and skills apply to all purchasing orientations, and the contextual knowledge and skills depend on customers’ prevalent purchasing orientations. Generic knowledge and skills relate to price setting, negotiation, communication and interaction skills, while contextual ones relate to knowledge brokering, ability to present solutions and relationship skills. Buying-oriented buyers value salespeople who are ‘action oriented experts, however at a bit of an arm’s length’, procurement buyers value salespeople who are ‘experts deeply dedicated to the customer and fostering the relationship’ and supply management buyers value salespeople who are ‘corporate-oriented experts’. In addition, the buyer’s perceptions on knowledge and selling skills differ from the seller’s ones. The buyer side emphasizes managing the subject matter, consisting of the expertise, understanding the customers’ business and needs, creating a customized solution and creating value, reliability and an ability to build long-term relationships, while the seller side emphasizes communica- tion, interaction and salesmanship skills. The study integrates the selling skills of the current three-component model− technical knowledge, salesmanship skills, interpersonal skills− and relationship skills and purchasing orientations, into a selling competency model. The findings deepen and update the content of these knowledges and skills in the B2B setting and create new insights into them from the buyer’s perspective, and thus the study increases contextual understanding of selling competencies. It generates new knowledge of the salesperson’s competencies for the relationship selling and personal selling and sales management literature. It also adds knowledge of the buying orientations to the buying behavior literature. The findings challenge sales management to perceive salespeople’s selling skills both from a contingency and competence perspective. The study has several managerial implications: it increases understanding of what the critical selling knowledge and skills from the buyer’s point of view are, understanding of how salespeople effectively implement the relationship marketing concept, sales management’s knowledge of how to manage the sales process more effectively and efficiently, and the knowledge of how sales management should develop a salesperson’s selling competencies when managing and developing the sales force. Keywords: selling competencies, knowledge, selling skills, relationship skills, purchasing orientations, B2B selling, abductive approach, technology firms

Educational Technology Decision-Making: A Case Study on Technology Acquisition for 746,000 Ontario Students

Very little research has examined K–12 educational technology decision-making in Canada. This collective case study explores the technology procurement process in Ontario’s publicly funded school districts to determine if it is informed by the relevant research, grounded in best practices, and enhances student learning. Using a qualitative approach, 10 senior leaders (i.e., chief information officers, superintendents, etc.) were interviewed. A combination of open-ended and closed-ended questions were used to reveal the most important factors driving technology acquisition, research support, governance procedures, data use, and assessment and return on investment (ROI) measures utilized by school districts in their implementation of educational technology. After participants were interviewed, the data were transcribed, member checked, and then submitted to “Computer-assisted NCT analysis” (Friese, 2014) using ATLAS.ti. The findings show that senior leaders are making acquisitions that are not aligned with current scholarship and not with student learning as the focus. It was also determined that districts struggle to use data-driven decision-making to support the governance of educational technology spending. Finally, the results showed that districts do not have effective assessment measures in place to determine the efficacy or ROI of a purchased technology. Although data are limited to the responses of 10 senior leaders, findings represent the technology leadership for approximately 746,000 Ontario students. The study is meant to serve as an informative resource for senior leaders and presents strategic and research-validated approaches to technology procurement. Further, the study has the potential to refine technology decision-making, policies, and practices in K–12 education.

Intellectual Property Protection For Plant Derived Vaccine Technology: Here They Come Are We Ready or Not ?

Il existe une nouvelle catégorie de technologie, les vaccins dérivés de plantes («VDPs»), qui englobe des produits qui ont un grand potentiel pour l’amélioration de la santé à l’échelle globale. Bien qu’ils ne soient pas encore disponibles pour le public, le développement des VDPs a progressé de façon telle qu’ils devraient être prêts à être mis en marché et distribués sous peu. Ainsi, c’est le moment idéal pour lancer un débat sur la meilleure façon de protéger cette nouvelle catégorie de technologie. Vu leur nature, les VDPs ne se qualifient pas parfaitement pour aucune forme de protection de propriété intellectuelle. En effet, un VDP est à la fois une variété de plante, une biotechnologie, un médicament et un produit qui vise spécifiquement les besoins de pays en voie de développement. Chacune de ces caractéristiques soulève ses propres problématiques en ce qui a trait à la propriété intellectuelle. C’est pourquoi il appert difficile d’identifier la forme de protection la plus adéquate et appropriée pour les VDPs. Cet article traite de la nature d’un VDP, des différentes catégories dans lesquelles il pourrait être classé, des différents types de systèmes de protection de propriété intellectuelle auxquels il pourrait être éligible ainsi que des problèmes qui pourraient être soulevés par tous ces éléments. Ces discussions visent à mettre l’accent sur le fait que nous avons affaire à une toute nouvelle catégorie d’innovation technologique. L’auteure est donc d’avis qu’une approche proactive est nécessaire pour discuter d’un système de protection de propriété intellectuelle en relation avec les VDPs. En ce moment, c’est l’inventeur qui choisi comment il protègera son invention. Les moyens employés par ce dernier pourraient être subséquemment modifiés ou annulés par une décision judiciaire mais comme plusieurs autres inventeurs d’une même catégorie de technologie auront probablement déjà adopté une stratégie de protection similaire, ce type de mesures judiciaire, très tard dans le processus, pourra avoir des résultats néfastes sur les détenteurs de droits. Le développement de lignes directrices d’entrée de jeu, avec l’aide d’un panel d’experts de préférence, peut contribuer à éviter les situations de confusion qui ont déjà été vécues avec l’application d’autres nouvelles technologies et qui devraient servir de leçon pour l’encadrement des VDPs.

Validité, fiabilité et reproductibilité des modèles digitaux obtenus avec iTero (Align Technology) et Unitek TMP Digital (3M) en comparaison avec les modèles de plâtre

Objectif: L'objectif primaire de cette étude était d'évaluer la validité, la fiabilité et la reproductibilité des mesures dentaires obtenues sur les modèles digitaux iTero (Align Technology, San Jose, Californie) et Unitek TMP Digital (3M, Monrovia, Californie) en comparaison avec celles obtenues sur les modèles de plâtre (gold standard). L'objectif secondaire était de comparer les deux différents matériaux à empreinte (l'alginate et le polyvinylsiloxane-PVS) afin de déterminer si le choix du matériau affectait la précision des mesures. Méthodes: Le premier volet de l'étude impliquait les modèles digitaux Unitek et iTero, obtenus à partir de 25 paires de modèles de plâtre choisis de façon randomisée et provenant de la pratique privée d'un des co-auteurs. Des empreintes d'alginate et de PVS ont été prises sur les modèles de plâtre et numérisées par le scanner Unitek. Les modèles ont ensuite été numérisés avec le scanner iTero. Le deuxième volet de l'étude cherchait à comparer les modèles digitaux iTero (numérisation intra-orale) avec les modèles de plâtre (empreintes d'alginate et de PVS) obtenus à partir de 25 patients de la clinique d'orthodontie de l'Université de Montréal ayant besoin d'un traitement orthodontique. Dans les deux volets de l'étude, deux auteurs ont pris les mesures suivantes sur les différents modèles: largeur mésio-distale de chaque dent de la première molaire à l'autre première molaire, le périmètre d'arcade, les distances intermolaire et intercanine, le surplomb vertical et le surplomb horizontal. Les ratios et excès Bolton 6 et 12, l'espace requis et les différentiels d'espace au maxillaire et à la mandibule, ont été calculés. Résultats: La fiabilité (ICC) entre les modèles digitaux (Unitek et iTero) et les modèles de plâtre était bonne à excellente pour toutes les mesures [ICC=0,762–0,998], et la fiabilité entre les deux matériaux à empreinte était excellente [ICC=0,947–0,996]. Dans les deux volets de l'étude, les mesures faites sur les modèles iTero étaient généralement plus grandes que celles faites sur les modèles de plâtre. Les plus grandes différences moyennes pour la comparaison iTero-plâtre étaient trouvées au niveau de l'espace disponible au maxillaire et à la mandibule (systématiquement plus grande pour cette variable), soit 2,24 mm et 2,02 mm respectivement dans le premier volet, et 1,17 mm et 1,39 mm respectivement dans le deuxième volet. Les différences étaient considérées cliniquement non significatives pour toutes les variables. La reproductibilité intra-examinateur était bonne à excellente pour les modèles de plâtre et les modèles digitaux, à l'exception du différentiel d'espace à la mandibule pour les modèles Unitek [ICC=0,690-0,692]. La reproductibilité inter-examinateur était bonne à excellente pour les modèles de plâtre et les modèles digitaux dans les deux volets de l'étude, mais acceptable à modérée pour les modèles Unitek au niveau des analyses Bolton 6 et 12, et des différentiels d'espace au maxillaire et à la mandibule [ICC=0,362-0,548]. Conclusions: La précision et la fiabilité des mesures dentaires faites sur les modèles digitaux Unitek et iTero étaient cliniquement acceptables et reproductibles en comparaison avec les celles faites sur les modèles de plâtre. Le choix de matériel à empreinte entre l'alginate et le PVS n'affectait pas la précision des mesures. Cette étude semble démontrer que les modèles digitaux Unitek et iTero, utilisés avec leur logiciel respectif, sont une alternative fiable et reproductible aux modèles de plâtre pour le diagnostic et l’analyse des modèles orthodontiques.