Piezoresistive cantilevers with an integrated bimorph actuator

Scanning Probe Microscopy (SPM) has become of fundamental importance for research in area of micro and nano-technology. The continuous progress in these fields requires ultra sensitive measurements at high speed. The imaging speed limitation of the conventional Tapping Mode SPM is due to the actuation time constant of piezotube feedback loop that keeps the tapping amplitude constant. In order to avoid this limit a deflection sensor and an actuator have to be integrated into the cantilever. In this work has been demonstrated the possibility of realisation of piezoresistive cantilever with an embedded actuator. Piezoresistive detection provides a good alternative to the usual optical laser beam deflection technique. In frames of this thesis has been investigated and modelled the piezoresistive effect in bulk silicon (3D case) for both n- and p-type silicon. Moving towards ultra-sensitive measurements it is necessary to realize ultra-thin piezoresistors, which are well localized to the surface, where the stress magnitude is maximal. New physical effects such as quantum confinement which arise due to the scaling of the piezoresistor thickness was taken into account in order to model the piezoresistive effect and its modification in case of ultra-thin piezoresistor (2D case). The two-dimension character of the electron gas in n-type piezoresistors lead up to decreasing of the piezoresistive coefficients with increasing the degree of electron localisation. Moreover for p-type piezoresistors the predicted values of the piezoresistive coefficients are higher in case of localised holes. Additionally, to the integration of the piezoresistive sensor, actuator integrated into the cantilever is considered as fundamental for realisation of fast SPM imaging. Actuation of the beam is achieved thermally by relying on differences in the coefficients of thermal expansion between aluminum and silicon. In addition the aluminum layer forms the heating micro-resistor, which is able to accept heating impulses with frequency up to one megahertz. Such direct oscillating thermally driven bimorph actuator was studied also with respect to the bimorph actuator efficiency. Higher eigenmodes of the cantilever are used in order to increase the operating frequencies. As a result the scanning speed has been increased due to the decreasing of the actuation time constant. The fundamental limits to force sensitivity that are imposed by piezoresistive deflection sensing technique have been discussed. For imaging in ambient conditions the force sensitivity is limited by the thermo-mechanical cantilever noise. Additional noise sources, connected with the piezoresistive detection are negligible.

Zur Druck-Querzug-Festigkeit von Stahlbeton und stahlfaserverstärktem Stahlbeton in scheibenförmigen Bauteilen

Am Fachgebiet Massivbau (Institut für Konstruktiven Ingenieurbau – IKI) des Fachbereichs Bauingenieurwesen der Universität Kassel wurden Bauteilversuche an zweiaxial auf Druck-Zug belasteten, faserfreien und faserverstärkten Stahlbetonscheiben durchgeführt. Dabei wurden die Auswirkungen der Querzugbeanspruchung und der Rissbildung auf die Druckfestigkeit, auf die Stauchung bei Erreichen der Höchstlast sowie auf die Drucksteifigkeit des stabstahl- und faserbewehrten Betons an insgesamt 56 faserfreien und faserverstärkten Beton- und Stahlbetonscheiben untersucht. Auf der Grundlage der experimentell erhaltenen Ergebnisse wird ein Vorschlag zur Abminderung der Druckfestigkeit des gerissenen faserfreien und faserbewehrten Stahlbetons in Abhängigkeit der aufgebrachten Zugdehnung formuliert. Die Ergebnisse werden den in DIN 1045-1 [D4], Eurocode 2 [E3, E4], CEB-FIP Model Code 1990 [C1] und ACI Standard 318-05 [A1] angegebenen Bemessungsregeln für die Druckstrebenfestigkeit des gerissenen Stahlbetons gegenübergestellt und mit den Untersuchungen anderer Wissenschaftler verglichen. Die bekannten Widersprüche zwischen den Versuchsergebnissen, den vorgeschlagenen Modellen und den Regelwerken aus U.S.A., Kanada und Europa können dabei weitgehend aufgeklärt werden. Für nichtlineare Verfahren der Schnittgrößenermittlung und für Verformungsberechnungen wird ein Materialmodell des gerissenen faserfreien und faserbewehrten Stahlbetons abgeleitet. Hierzu wird die für einaxiale Beanspruchungszustände gültige Spannungs-Dehnungs-Linie nach Bild 22 der DIN 1045-1 auf den Fall der zweiaxialen Druck-Zug-Beanspruchung erweitert.

Biofilmbildung bei Pflanzen-assoziierten Bakterien der Gattung Methylobacterium und molekulargenetisch-physiologische Charakterisierung eines neuen Marchantia-Isolats (Mtb. sp. JT1)

Bakterien existieren bevorzugt in Biofilmen. Das Zusammenleben in diesen Gemeinschaften bietet den einzelnen Mikroben einen wirksamen Schutz und ermöglicht die Ausbildung langfristiger, synergistischer Wechselwirkungen, die mit multizellulären Systemen verglichen werden können. Biofilme bestehen aus Mikrooganismen-Populationen, die sich an Grenzflächen ansammeln und typischerweise von einer Matrix aus extrazellulären polymeren Substanzen umgeben sind. Auch auf Pflanzen-Oberflächen bilden viele Bakterien Biofilme, um ihre Überlebenswahrscheinlichkeit zu erhöhen. In dieser Arbeit wurde die Biofilmbildung bei Pflanzen-assoziierten Bakterien der Gattung Methylobacterium (Mtb.) untersucht, wobei molekular- und mikrobiologische sowie mikroskopische Techniken eingesetzt wurden. Es zeigte sich, dass alle untersuchten Vertreter der Gattung Methylobacterium in unterschiedlichem Ausmaß Biofilme bilden. Die Ausprägung ist dabei Taxon (bzw. Isolat)-spezifisch und vor allem von der Stickstoff-Verfügbarkeit abhängig. Jedoch spielen auch andere Umweltfaktoren, wie die Versorgung der Zellen mit Phosphat und die Zelldichte, bei der Ausbildung der überzellulären Einheiten eine wichtige Rolle. Die Matrix der Biofilme wird meist durch ein fibrilläres Netzwerk gebildet. Dabei handelt es sich um Heteropolysaccharide, die von den Bakterien synthetisiert und sezerniert werden. Einige Isolate bilden zusätzlich zahlreiche Fimbrien (Auswüchse), durch die sie an andere Zellen oder Oberflächen binden können. Im zweiten Teil dieser Arbeit wurden mehrere neue Methylobacterium-Isolate physiologisch und molekulargenetisch charakterisiert (Nährstoffverwertung, DNA-Sequenzen verschiedener Gene, phylogenetische Analysen usw.). Im Vordergrund stand hierbei der von einer urtümlichen Landpflanze, dem Lebermoos (Marchantia polymorpha), isolierte Stamm Mtb. sp. JT1. Dabei zeigten sich deutliche Unterschiede in der Morphologie und Physiologie des Bakterienstamms JT1 und dem nahe verwandten Stamm 5b.2.20 zu den bereits beschriebenen Taxa der Gattung, so dass eine Spezies-Neubeschreibung erforderlich war. Als Artname wurde aufgrund der außergewöhnlichen Oberflächenstrukturen Mtb. fimbriae sp. nov. eingeführt. Auch andere Methylobakterien (unter anderem Isolat Mtb. sp. F3.2, isoliert vom Laubmoos Funaria hygrometrica) stellen wahrscheinlich Vertreter einer neue Spezies dar (Artname Mtb. funariae sp. nov.). Jedoch zeigen Mtb. fimbriae und Mtb. funariae nur geringe physiologische und morphologische Unterschiede und konnten auf Grundlage umfassender DNA-DNA-Hybridisierungs-Studien nicht eindeutig voneinander abgegrenzt werden.

Modelo tridimensional del tendón del músculo supraespinoso

Introducción: Teniendo en cuenta el envejecimiento de la población y la alta prevalencia de las lesiones del manguito rotador no es de extrañar que esta patología se convierta en un problema de salud pública. Se sabe que el aumento en el tamaño de una lesión se asocia con la aparición de síntomas, pero no existen herramientas que permitan predecir la evolución del tamaño de una lesión. Con esto en mente se desarrollo una línea de investigación para estudiar el mecanismo de falla que inicia con la realización de un modelo tridimensional de un tendón del musculo supraespinoso sano. Materiales y métodos: Se caracterizo el tendón del músculo supraespinoso aplicando cargas uniaxiales a 7 complejos humero-tendón-escápula cadavéricos. Con los datos obtenidos se alimento un modelo tridimensional lineal isotrópico analizando la concentración de esfuerzos de von Misses Resultados: Del ensayo uniaxial se obtuvieron curvas esfuerzo-deformación homogéneas para el 20% de la deformación inicial, obteniendo un modulo de Young (14.4±2.3MPa) y un coeficiente de Poisson (0.14) con una concentración de esfuerzos de en la zona central de la cara articular del tendón, cercana a su inserción. Encontramos una disminución del 5% en los esfuerzos al retirar el acromion del modelo. Conclusiones: Se caracterizó de manera exitosa y se obtuvo un modelo tridimensional del tendón. La distribución de esfuerzos es compatible con la reportada en la literatura. El acromion no tiene mayor importancia en la magnitud de los esfuerzos en nuestro modelo. Este es el punto de partida para estudiar el mecanismo de falla.

Uso de la matriz extracelular como material para ingeniería de tejidos

Introducción: La evaluación de injertos vasculares de submucosa de intestino delgado para la regeneración de vasos sanguíneos ha producido una permeabilidad variable (0-100%) que ha sido concurrente con la variabilidad en las técnicas de fabricación. Metodología: Investigamos los efectos de fabricación en permeabilidad y regeneración en un diseño experimental de 22factorial que combino: 1) preservación (P) o remoción (R) de la capa estratum compactum del intestino, y 2) deshidratada (D) o hidratada (H), dentro de cuatro grupos de estudio (PD, RD, PH, RH). Los injertos fueron implantados en las Arterias Carótidas de porcinos (ID 4.5mm, N=4, 7d). Permeabilidad, trombogenicidad, reacción inflamatoria, vascularización, infiltración de fibroblastos, perfil de polarización de macrófagos y fuerza tensil biaxial fueron evaluadas. Resultados: Todos los injertos PD permanecieron permeables (4/4), pero tuvieron escasa vascularización e infiltración de fibroblastos. El grupo RD permaneció permeable (4/4), presentó una extensa vascularización e infiltración de fibroblastos, y el mayor número del fenotipo de macrófagos (M2) asociado a regeneración. El grupo RH presentó menor permeabilidad (3/4), una extensa vascularización e infiltración de fibroblastos, y un perfil dominante de M2. El grupo PH presentó el menor grado de permeabilidad, y a pesar de mayor infiltración celular que PD, exhibió un fenotipo de macrófagos dominante adverso. La elasticidad de los injertos R evolucionó de una manera similar a las Carótidas nativas (particularmente RD, mientras que los injertos P mantuvieron su rigidez inicial. Discusión: Concluimos que los parámetros de fabricación afectan drásticamente los resultados, siendo los injertos RD los que arrojaron mejores resultados.

Nuclear accumulation of myocyte muscle LIM protein is regulated by heme oxygenase 1 and correlates with cardiac function in the transition to failure

Impaired mechanosensing leads to heart failure and we have previously shown that a decreased ratio of cytoplasmic to nuclear CSRP3/Muscle LIM protein (MLP ratio) is associated with a loss of mechanosensitivity. Here we tested whether passive or active stress/strain was important in modulating the MLP ratio and determined whether this correlated with heart function during the transition to failure. We exposed cultured neonatal rat myocytes to 10% cyclic mechanical stretch at 1 Hz, or electrically paced myocytes at 6.8 V (1 Hz) for 48 h. The MLP ratio decreased 50% (P < 0.05, n = 4) only in response to electrical pacing, suggesting impaired mechanosensitivity. Inhibition of contractility with 10 μM blebbistatin resulted in a ∼3 fold increase in the MLP ratio (n = 8, P < 0.05), indicating that myocyte contractility regulates nuclear MLP. Inhibition of histone deacetylase (HDAC) signaling with trichostatin A increased nuclear MLP following passive stretch, suggesting that HDACs block MLP nuclear accumulation. Inhibition of heme-oxygenase1 (HO-1) activity with PPZII blocked MLP nuclear accumulation. To examine how mechanosensitivity changes during the transition to heart failure, we studied a guinea pig model of angiotensin II infusion (400 ng/kg/min) over 12 weeks. Using subcellular fractionation we showed that the MLP ratio increased 88% (n = 4, P < 0.01) during compensated hypertrophy, but decreased significantly during heart failure (P < 0.001, n = 4). The MLP ratio correlated significantly with the E/A ratio (r = 0.71, P < 0.01 n = 12), a clinical measure of diastolic function. These data indicate for the first time that myocyte mechanosensitivity as indicated by the MLP ratio is regulated primarily by myocyte contractility via HO-1 and HDAC signaling.

Cambrian mafic to felsic magmatism and its connections with transcurrent shear zones of the Borborema Province (NE Brazil): Implications for the late assembly of the West Gondwana

New U-Pb (SHRIMP) and (40)Ar/(39)Ar isotopic data of igneous rocks and mylonites of the Borborema Province (NE Brazil) show that a wide range of tectonothermal events affected the province during the transition from the Precambrian to the Cambrian. Concordant zircon U-Pb data constrained the crystallization age of mafic stocks, mafic to felsic dikes and granite batholiths between 548 and 533 Ma. These bodies were emplaced in a regional strain field combining extension and dextral shearing. The ductile shear deformation overprinted an older basement fabric to develop a low- to medium metamorphic grade vertical mylonite belt that cut the province in the E-W direction. Magnetic fabrics of the Cambrian batholiths determined by anisotropy of magnetic susceptibility are consistent with syntectonic emplacement. The magmatic pulses and shear deformation would have supplied enough heat to reset the synkinematic micas of mylonites to yield (40)Ar/(39)Ar plateau cooling ages between ca. 550 and 510 Ma. These results provide evidence that emplacement of Early Cambrian mafic and felsic magmas were accompanied by regional-scale shear deformations, probably in the consequence of late collisions along the West Gondwana margin. (C) 2010 Published by Elsevier B.V.

A dislocation based theory for the deformation hardening behavior of DP steels : Impact of martensite content and ferrite grain size

A dislocation model, accurately describing the uniaxial plastic stress-strain behavior of dual phase (DP) steels, is proposed and the impact of martensite content and ferrite grain size in four commercially produced DP steels is analyzed. It is assumed that the plastic deformation process is localized to the ferrite. This is taken into account by introducing a non-homogeneity parameter, f(e), that specifies the volume fraction of ferrite taking active part in the plastic deformation process. It is found that the larger the martensite content the smaller the initial volume fraction of active ferrite which yields a higher initial deformation hardening rate. This explains the high energy absorbing capacity of DP steels with high volume fractions of martensite. Further, the effect of ferrite grain size strengthening in DP steels is important. The flow stress grain size sensitivity for DP steels is observed to be 7 times larger than that for single phase ferrite.

Estudo do comportamento de um solo mole tratado com cal, visando seu uso em fundações superficiais

Neste trabalho foi analisada a melhoria nas características de um solo mole quando tratado com cal, bem como a viabilidade técnica de se utilizar este novo material como uma camada suporte de fundações superficiais. O solo estudado classifica-se pedologicamente como Gley Húmico e a jazida localiza-se no município de Canoas/RS, às margens da BR 386. O trabalho teve as seguintes finalidades: realizar um estudo da influência dos diferentes teores de cal sobre as características tensão x deformação do solo tratado; verificar o ganho de resistência com o tempo de cura; modelar o comportamerito tensão x deformação do material tratado; realizar simulações numéricas, através do Método dos Elementos Finitos, do comportamento carga x recalque de fundações continuas flexíveis assentes sobre o novo material. Adotou-se o teor ótimo de cal (obtido pelo método de Eades & Grim, 1966) de 9% e dois valores inferiores de 7% e 5%. Realizaram-se os seguintes ensaios sobre o solo natural e as misturas de solo-cal: limites de Atterberg, compactação, granulometria, difratograma de raio X, permeabilidade (triaxial) e ensaios triaxiais adensados não drenados(CIU). Todos os ensaios foram realizados para três tempos de cura (7, 28 e 90 dias) e os corpos de prova foram curados em câmara úmida. Para modelar o comportamento tensão x deformação do solo melhorado, adotou-se o Modelo Hiperbólico e para o solo natural o Modelo Cam-Clay Modificado. O Modelo Hiperbólico foi implementado no software CRISPSO, desenvolvido na Universidade de Cambridge, Inglaterra. O software foi utilizado em um estudo paramétrico para determinar a influência do processo de estabilização no comportamento carga x recalque de fundações superficiais. Dos resultados obtidos, concluiu-se: que o método de Eades & Grim (1966) não mostrou-se adequado para determinação do teor ótimo de cal; houve, de maneira geral, melhora nas características físicas com o tratamento com cal; não houve ganho de resistência com o tempo de cura; o modelo hiperbólico representou bem o comportamento das misturas de solo cal e a colocação de uma camada de solo tratado apresenta melhoras no comportamento carga x recalque de fundações superficiais contínuas flexíveis.

Desenvolvimento de elastômeros termoplásticos a partir de SBR epoxidada e polipropileno

Os elastômeros termoplásticos vulcanizados (TPVs) na sua maioria constituídos por borrachas apolares (EPDM, NR) e poliolefinas (PP, PE), apresentam a vantagem de serem processáveis como termoplásticos e serem facilmente reciclados. No entanto, apresentam desvantagens no que se refere à sua baixa resistência a óleos, combustíveis e graxas em relação à borracha termofixa. Este trabalho, teve como objetivo estudar a obtenção de TPVs com propriedades mecânicas adequadas e resistência a óleos e solventes orgânicos, a partir da borracha comercial SBR 1502 parcialmente epoxidada. Esta, por ter a estrutura química de sua cadeia principal modificada pela introdução de grupos epóxidos, deve apresentar melhor resistência a óleos e solventes. Os TPVs foram obtidos em misturador fechado acoplado a um reômetro Haake, na temperatura de 1800C e velocidade de rotor de 75 rpm, vulcanizados dinamicamente com o sistema Bismaleimida/peróxido de dicumila. Foram caracterizados quanto às suas propriedades mecânicas por medidas tensão-deformação, medidas mecânicas dinâmicas, inchamento em ciclohexano, THF e óleo IRM 903, dureza. A morfologia foi determinada por microscopia eletrônica de varredura, MEV. Foram analisados os fatores que influenciam as propriedades dos TPVs, tais como composição (relação PP/SBR), teor de BMI, grau de epoxidação da borracha, uso de agente compatibilizante. O TPV na composição PP/SBR 40/60, esta epoxidada em 40 mol % e contendo o agente compatibilizante Vestenamer adicionado na forma de blenda (borracha/agente compatibilizante) apresentou a melhor resposta em termos de tensão-deformação na ruptura. Os TPVs com a SBR epoxidada em 70% apresentaram melhor resistência a óleo e solventes. Os fatores, potencialmente, capazes de influenciar a dureza dos TPVs também foram avaliados. Neste particular, verificou-se que o tipo de poliolefina, bem como o uso de plastificante são os fatores que mais influenciam a dureza dos TPVs.

Plastificação de um solo cimentado curado sob tensão

A fim de avaliar a contribuição das ligações cimentantes no comportamento tensão-deformação dos solos cimentados, bem como quantificar a variação das tensões de início de plastificação e incremento de tensão de plastificação em função do índice de vazios de cura, foram realizados dezoito ensaios de compressão isotrópica em amostras artificialmente cimentadas curadas com diferentes tensões confinantes, índices de vazios e teores de cimento. As amostras foram inicialmente adensadas a várias tensões confinantes ao longo da linha de compressão normal do solo sem cimentação, simulando a formação de elementos de solos em diferentes profundidades de um depósito sedimentar cimentado. Após o adensamento, as amostras eram curadas para posterior aplicação de incrementos de tensão isotrópica. Complementarmente, dezenove ensaios triaxiais drenados foram realizados em amostras artificialmente cimentadas curadas sob diferentes tensões confinantes e índices de vazios de forma a analisar as modificações dos parâmetros de resistência, deformabilidade e plastificação em função do índice de vazios e tensão de cura. Por final, um novo modelo matemático foi proposto para simular os ensaios isotrópicos das amostras curadas com diferentes índices de vazios e teores de cura, descrevendo o comportamento teórico dos elementos de solo situados nas diferentes profundidades do depósito fictício de solo cimentado. A capacidade do modelo de simular os resultados dos ensaios isotrópicos para uma gama ampla de índice de vazios de cura e teores de cimento também foi apresentada. Comentários acerca das respostas obtidas com simulações de amostras curadas a altos e baixos índices de vazios, e solicitadas a elevadas tensões isotrópicas, também são apresentadas juntamente com uma análise dos três parâmetros adicionais requeridos pelo modelo em relação ao modelo Cam Clay: um parâmetro de medida de nível de cimentação, um parâmetro definidor do tipo de comportamento da estrutura cimentante (rígido, rígido-plástico, linear, etc.), e um parâmetro que relaciona a magnitude das tensões da estrutura cimentante com o nível de cimentação da amostra.

The Effect of Residence Time on the Tensile Properties of Superelastic and Thermal Activated Ni-Ti Orthodontic Wires

Since the 1980s, different devices based on superelastic alloys have been developed to fulfill orthodontic applications. Particularly in the last decades several researches have been carried out to evaluate the mechanical behavior of Ni-Ti alloys, including their tensile, torsion and fatigue properties. However, studies regarding the dependence of elastic properties on residence time of Ni-Ti wires in the oral cavity are scarce. Such approach is essential since metallic alloys are submitted to mechanical stresses during orthodontic treatment as well as pH and temperature fluctuations. The goal of the present contribution is to provide elastic stress-strain results to guide the orthodontic choice between martensitic thermal activated and austenitic superelastic Ni-Ti alloys. From the point of view of an orthodontist, the selection of appropriate materials and the correct maintenance of the orthodontic apparatus are essential needs during clinical treatment. The present work evaluated the elastic behavior of Ni-Ti alloy wires with diameters varying from 0.014 to 0.020 inches, submitted to hysteresis tensile tests with 8% strain. Tensile tests were performed after periods of use of 1, 2 and 3 months in the oral cavity of patients submitted to orthodontic treatment. The results from the hysteresis tests allowed to exam the strain range covered by isostress lines upon loading and unloading, as well as the residual strain after unloading for both superelastic and thermal activated Ni-Ti wires. Superelastic Ni-Ti wires exhibited higher load isostress values compared to thermal activated wires. It was found that such differences in the load isostress values can increase with increasing residence time.

Estudo do comportamento mecânico de areias artificialmente cimentadas

Soil improved with the addition of cement have been utilized as an alternative to the construction of various types of geotechnical works, almost always present economic and environmental advantages. This paper presents a study on the usage of cement in the improvement of mechanical properties of sandy soils, characteristic of the region of Natal, collected from its dunes. This research was made in order to analyze the influence of cement content, voids, and also including water immersion and confining pressure. Samples molded from cement-soil mixtures were tested for unconfined compression tests and triaxial tests. The samples had the percentage of cement mixed in 2.5%, 5% and 10% by weight. The cement agent used was the Portland Cement of High Early strength(CPV-ARI), which promoted agility to the experimental procedure for presenting a rapid gain in strenght. The void ratio used ranged from 0.7 (more compact), 0,9 and 1,1(softer). The soil under study can be considered as pure sand. In general, it can be stated that the larger the amount of cement added to the sand studied is, the greater ultimate strength will be. Likewise, as more compact the soil is, the less void ratio and more resistant it will be present. The confining pressure tends to increase the resistance of the specimens. The cementing adopted grades showed that the use of different criteria for failure did not significantly alter the stress-strain parameters for the sand studied. The angle of friction values were found within the typical range of medium and compact sands. Cementing acted in the sand providing an intercepted cohesion which increased enhancing the potential cementation. In triaxial compression tests, the sand with void ratio is equal to 0.7 and showed the expected behavior for a compact sand while the stress-strain behavior of the same sand with the void ratio of 0.9 tended to be expected for the soft sand as well

Análise tribológica das malhas multifuncionais obtidas por multicamadas

The present work consists in the analysis of tribologycal properties of basic and multifunctional knitted fabrics. This knowledge has fundamental importance for the textile industry since it can quantify, in an objective way, the tactil. The fabrics used were characterized by friction and mechanical tests for determining the viscoelastic region, wear resistance and friction coefficient of the fabrics used. The stress-strain curve was obtained by the method Kawabata, KES-FB1. Wear tests performed with the aid of equipment Martindale. The measurement of friction coefficient, two methods were used and analyzed comparatively. The first was a method already established worldwide known as KES-FB4 and the second was an innovative method called FRICTORQ, developed by the University of Minho. These two methods were compared taking into account the relative motion between the tribologycal pairs are different from each method. While the first motion is translational, the second is rotational. It was formal that the knitted had a multifunctional fabrics tribologycal performance which was better than the basic knitted fabrics, as the viscoelastic region, was laager highlighting a multifunctional structure, with greater wear resistance mainly on the back side of the knitted fabrics and lower friction coefficient. Performing a comparative analysis between two methods used to measure the friction coefficient, it was formal that both methods were consistent in terms of results. In operational terms, the FRICTORQ showed ease of operation and increased reproducibility of results

Thermoplastic starch/natural rubber blends

Thermoplastic starch/natural rubber polymer blends were prepared using directly natural latex and cornstarch. The blends were prepared in an intensive batch mixer at 150 degreesC, with natural rubber content varying from 2.5 to 20%. The blends were characterised by mechanical analysis (stress-strain) and by scanning electron microscopy. The results revealed a reduction in the modulus and in tensile strength, becoming the blends less brittle than thermoplastic starch alone. Phase separation was observed in some compositions and was dependent on rubber and on plasticiser content (glycerol). Increasing plasticiser content made possible the addition of higher amounts of rubber. The addition of rubber was, however, limited by phase separation the appearance of which depended on the glycerol content. Scanning electron microscopy showed a good dispersion of the natural rubber in the continuos phase of thermoplastic starch matrix. (C) 2003 Elsevier B.V. Ltd. All rights reserved.