Reduction of drag due to lift at supersonic speeds

"Aeronautical Research Laboratory, Contract no. AF 33(616)-2170, Project no. 1366."

Fluid-dynamic drag; practical information on aerodynamic drag and hydrodynamic resistance

Mode of access: Internet.

Conveyor drag type piler self-propelled crawler mounted gasoline driven 35 ft long, 75 ton per hr capacity : Barber-Greene model 689 (less engine) /

Includes index.

Wire drag manual.

Mode of access: Internet.

Computed induced velocity, induced drag, and angle of attack distributions for a two-bladed rotor

Cover title.

Molecular size as the main determinant of solute maximum flux across the skin

One of the most important determinants of dermatological and systemic penetration after topical application is the delivery or flux of solutes into or through the skin. The maximum dose of solute able to be delivered over a given period of time and area of application is defined by its maximum flux (J(max), mol per cm(2) per h) from a given vehicle. In this work, J(max) values from aqueous solution across human skin were acquired or estimated from experimental data and correlated with solute physicochemical properties. Whereas epidermal permeability coefficients (k(p)) are optimally correlated to solute octanol-water partition coefficient (K-ow) and molecular weight (MW) was found to be the dominant determinant of J(max) for this literature data set: log J(max)=-3.90-0.0190MW (n=87, r(2)=0.847, p

Parasitic isopod Anilocra apogonae, a drag for the cardinal fish Cheilodipterus quinquelineatus

Cymothoid isopods Anilocra apogonae are regular ectoparasites of the cardinal fish Cheilodipterus quinquelineatus on the Great Barrier Reef. To determine whether this large isopod, attached to the head of the fish, affects the physiology and behaviour of its host, we conducted morphological measurements to obtain a condition index and several laboratory experiments on fish with and without isopods. The condition index did not vary between parasitised and non-parasitised wild fish. However, we found that parasitised fish lost more weight than unparasitised fish when fed a low food ration. Parasitised fish also had a higher rate of oxygen consumption than non-parasitised fish. When maintaining body posture in calm water, parasitised fish had an elevated pectoral fin beat frequency, probably because the isopod attaches asymmetrically, causing an asymmetrical weight balance for which the fish needs to compensate. Moreover, the sustained aerobic swimming speed as well as the swimming endurance at high water speeds were reduced in parasitised fish, possibly because of the drag from the parasite. The results suggest that parasites can have significant effects on fish even if this is not revealed by their body condition index in the wild. The metabolic effects found imply that parasitised fish may have to spend more time foraging to compensate for their higher metabolism. This could expose them to a higher risk of being eaten, a situation made worse by an impaired swimming ability that may reduce their capacity to escape a predator.

An analysis of the relationship between grain size, solute content, and the potency and number density of nucleant particles

To be able to determine the grain size obtained from the addition of a grain refining master alloy, the relationship between grain size (d), solute content (defined by the growth restriction factor Q), and the potency and number density of nucleant particles needs to be understood. A study was undertaken on aluminium alloys where additions of TiB2 and Ti were made to eight wrought aluminum alloys covering a range of alloying elements and compositions. It was found from analysis of the data that d = a/(3)root pct TiB2 + b/Q. From consideration of the experimental data and from further analysis of previously published data, it is shown that the coefficients a and b relate to characteristics of the nucleant particles added by a grain refiner. The term a is related to the maximum density of active TiB2 nucleant particles within the melt, while b is related to their potency. By using the analysis methodology presented in this article, the performance characteristics of different master alloys were defined and the effects of Zr and Si on the poisoning of grain refinement were illustrated.