Compósitos de matriz metálica à base níquel com adição de TaC e NbC produzidos via metalurgia do pó

Carbide reinforced metallic alloys potentially improve some important mechanical properties required for the overall use of important engineering materials such as steel and nickel. Nevertheless, improved performance is achieved not only by composition enhancement but also by adequate processing techniques, such as novel sintering methods in the case of powder metallurgy. The method minimizes energy losses in addition to providing uniform heating during sintering. Thus, the general objective of this study was to evaluate the density, hardness, flexural strength, dilatometric behavior and to analyze the microstructure of metal matrix composites based nickel with addition of carbides of tantalum and / or niobium when sintered in a conventional furnace and Plasma assisted debinding and sintering (PADS). Initially, were defineds best parameters of granulation, screening and mixing procedure. After, mixtures of carbonyl Ni and 5%, 10% and 15 wt.% NbC and TaC were prepared in a Y-type mixer under wet conditions during 60 minutes. The mixtures were then dried and granulated using 1.5 wt. % paraffin diluted in hexane. Granulates were cold pressed under 600 MPa. Paraffin was then removed from the pressed pellets during a pre-sintering process carried out in a tubular furnace at 500 °C during 30 min. The heating rate was 3 ºC/min. The pellets were then sintered using either a plasma assisted reactor or a conventional resistive tubular furnace. For both methods, the heating rate was set to 8 ºC/min up to 1150 °C. The holding time was 60 minutes. The microstructure of the sintered samples was evaluated by SEM. Brinell hardness tests were also carried out. The results revealed that higher density and higher hardness values were observed in the plasma-assisted sintered samples. Hardness increased with the concentration of carbides in the Ni-matrix. The flexural strength also increased by adding the carbides. The decline was larger for the sample with addition of 5% 5% TaC and NbC. In general, compositions containing added carbide 10% showed less porous and more uniform distribution of carbides in the nickel matrix microstructural appearance. Thus, both added carbide and plasma sintering improved density, hardness, flexural strength and microstructural appearance of the composites

Avaliação da incorporação combinada dos resíduos de cascalho de perfuração de poço de petróleo e de polimento do porcelanato em cerâmica vermelha

Among the industries, those that produce ceramic porcelain for use in construction industry and oil, during the exploration and production period, play an important role in the production of waste. Much research has been carried out both by academia and the productive sector, sometimes reintroducing them in the same production line that generated them, sometimes in areas unrelated to their generation, as in the production of concrete and mortar for the construction, for example, but each one in an isolated way. In this research, the aim is to study the combined incorporation of the waste drill cuttings of oil well and the residue of the polishing of porcelain, generated in the final stage of finishing of this product in a clay matrix, for the production of red pottery, specifically bricks, ceramic blocks and tiles. The clay comes from the municipality of São Gonçalo, RN, the drilling waste is from the Natal basin, in Rio Grande do Norte, and the residue of the polishing proceeds from a ceramic porcelain of the State of Paraíba. For this purpose, we used a mixture of a plastic clay with a non-plastic, in a ratio of 50% each, settling formulations with the addition of these two residues in this clay matrix. In the formulations, both residues were incorporated with a minimum percentage of 2.5% and maximum of 12.5%, varying from 2.5% each, in each formulation, which the sum of the waste be no more than 15%. It should be noted that the residue of the polishing of ceramic porcelain is a IIa class (not inert). The materials were characterized by XRF, XRD, TG, DTA, laser granulometry and the plasticity index. The technological properties of water absorption, apparent porosity, linear shrinkage of burning, flexural tensile strength and bulk density were evaluated after the sintering of the pieces to 850 °C, 950 °C and 1050 °C, with a burning time of 3 hr, 3 hr and 30 minutes, and 3 hr and 50 minutes, respectively, with a heating rate of 10 °C/minute, for all formulations and landing of 30 minutes. To better understand the influence of each residue and temperature on the evaluated properties, we used the factorial planning and its surfaces of response for the interpretation of the results. It was found that the temperature has no statistical significance at a 95% of reliability level in flexural tensile strength and that it decreases the water absorption and the porosity, but increases the shrinkage and the bulk density. The results showed the feasibility of the desired incorporation, but adjusting the temperature to each product and formulation, and that the temperatures of 850 °C and 950 °C were the one that responded to the largest number of formulations

Uso de argilominerais e diatomita como adsorvente de fenóis em águas produzidas na indústria de petróleo

The oil production in Brazil has been increasing each year. Consequently, increasing volumes of water produced are generated with large quantities of contaminants, which brings many problems in disposing of these waters. The concern that the concentrations of contaminants in water produced meet existing laws for disposal of effluents, has been extremely important for the development of different techniques for treatment of water produced. The study of clay minerals as adsorbents of organic contaminants has grown considerably so in order to combine the low cost with the efficiency of environmental preservation and health issues. Thus, this study aims to understand the characteristics of vermiculite clay, sodium bentonite, calcium bentonite and diatomite and evaluate their performance as adsorbents for phenol in the water produced. Through adsorption isotherms it was possible to observe the behavior of these adsorptive clay and diatomite for adsorption of phenol, the main phenolic compound found in water produced. Different concentrations of synthetic solutions of phenol were put in touch with these adsorbents under same conditions of agitation and temperature. The adsorbents were composted adsorptive favorable, but the vermiculite and diatomite showed little capacity for absorption, being suggested for absorbs small concentrations of phenol in the balance isothermal

Avaliação da biodegradabilidade de petróleo utilizando microrganismos isolados do estuário do Rio Potengi (RN)

The oil activity in the Rio Grande do Norte State (RN) is a permanent threat to coastal ecosystems, particularly mangroves, with the possibility of oil spills. In this context, the objective of this study was to evaluate the potential resistance of the mangrove environment of a possible spill. Were selected and isolated microorganisms degrading oil by the technique of enrichment cultures and formation of a bacterial consortium. The kinetic study of the consortium was held in rotary incubator shaken at 150 rpm and 30° C. Samples were taken at intervals of 4 hours for analysis of cell concentration and surface tension. The biodegradation was monitored using two methods of respirometry: manometric (OxiTop-C ®) and conductivimetry, where the biodegradation of oil was estimated indirectly by oxygen consumption and CO2 production, respectively. Furthermore, it was used a full 2² factorial design with triplicate at central point to the runs that used the conductivimetric methodology.. The technique of enrichment cultures allowed to obtain thirteen bacterial strains. Kinetic study of the consortium, we can showed the absence of the lag phase, reaching a maximum cell concentration of 2.55 g / L at 16 h of cultivation and a reduction on surface tension. When we adopted the methodology of OxiTop-C was detected a band indicating biodegradability (1% oil v/v), however when we used the conductivimetry methodology did not observe any band that would indicate effective biodegradation. By monitoring a process of biodegradation is necessary to observe the methodology will be adopted to evaluate the biodegradation process, since for the same conditions adopted different methodologies can produce different results. The oil-degrading isolates from soils of the mangrove estuary Potengi / RN are largely to be used in bioremediation strategies of these places, in the case of a possible oil spill, or it can be used in the treatment of waste oil generated in saline environments, since they are optimized the conditions of the tests so that the efficiency of biodegradation reach the minimum level suggested by the standarts

Pirólise termoquímica de pós da fibra de coco seco em um reator de cilindro rotativo para produção de bio-óleo

This master thesis aims at developing a new methodology for thermochemical degradation of dry coconut fiber (dp = 0.25mm) using laboratory rotating cylinder reactor with the goal of producing bio-oil. The biomass was characterized by infrared spectroscopy with Fourier transform FTIR, thermogravimetric analysis TG, with evaluation of activation energy the in non-isothermal regime with heating rates of 5 and 10 °C/min, differential themogravimetric analysis DTG, sweeping electron microscopy SEM, higher heating value - HHV, immediate analysis such as evaluated all the amounts of its main constituents, i.e., lignin, cellulose and hemicelluloses. In the process, it was evaluated: reaction temperature (450, 500 and 550oC), carrier gas flow rate (50 and 100 cm³/min) and spin speed (20 and 25 Hz) to condensate the bio-oil. The feed rate of biomass (540 g/h), the rotation of the rotating cylinder (33.7 rpm) and reaction time (30 33 min) were constant. The phases obtained from the process of pyrolysis of dry coconut fiber were bio-oil, char and the gas phase non-condensed. A macroscopic mass balance was applied based on the weight of each phase to evaluate their yield. The highest yield of 20% was obtained from the following conditions: temperature of 500oC, inert gas flow of 100 cm³/min and spin speed of 20 Hz. In that condition, the yield in char was 24.3%, non-condensable gas phase was 37.6% and losses of approximately 22.6%. The following physicochemical properties: density, viscosity, pH, higher heating value, char content, FTIR and CHN analysis were evaluated. The sample obtained in the best operational condition was subjected to a qualitative chromatographic analysis aiming to know the constituents of the produced bio-oil, which were: phenol followed by sirigol, acetovanilona and vinyl guaiacol. The solid phase (char) was characterized through an immediate analysis (evaluation of moisture, volatiles, ashes and fixed carbon), higher heating value and FTIR. The non-condensing gas phase presented as main constituents CO2, CO and H2. The results were compared to the ones mentioned by the literature.

Corpo e Velhice: um estudo da qualidade de vida de idosos da Vila Vicentina Júlia Freire em João Pessoa

The aim of this study was to follow the daily routine of elderly individuals residing at the Vila Vicentina Júlia Freire (VVJF) nursing home in João Pessoa, Brazil, observing and analyzing as much as possible, the way in which they live in a group and how they deal, through personal experiences, with their own body image and with that of others. The results were obtained from information considered relevant, according to the perspectives of the residents themselves, contained in narratives of their history and related to their quality of life. Our interest lays in how they coped with changes in their bodies at old age and adapted to the challenges of this new phase. To obtain this information, with significant expressions, we used the Narrative Interview (NI) as a research tool in order to redeem their life experience and develop an understanding of their impressions about the life experience at the current nursing home. We selected, among the housed, ten subjects - actors - to appear as a sample of the group together. The design of our sample had a hybrid model, combining two types: random sample (probability) and an intentional sample (not probability). After recording transcripts and ensuring that all the subjects showed common interests that were relevant to the group, we chose three categories for analysis as follows: a. the elderly as seen by themselves and by others; b. religiosity as a moral factor; c. intimacy and relationships. Our choice was based on the importance of the theme as a multidisciplinary topic in the quality of life of populations. The subjects, chosen as spokespersons for the VVJF, spoke, among other things, about the way in which they viewed the world, their own body and how they experienced the environment and their fellow residents, in an attitude of reflection and criticism that confirms the lucidity of an old age conditioned to an elderly institution. The method allowed us to investigate our subjects from a multidisciplinary point of view. We suggest other studies in assorted areas of the human sciences, having as principle, man at the center of all our scientific questionings. The paradigm that the elder is, necessarily, unhappy in his sheltered has been, in this job, broken through the testimonies collected, establishing multiple perspectives of the analyzed subjects by their respective narrative records. Involving the participation of researchers with major in Administration, Communication and Law, this study filled, in this aspect, the requirements of the multidisciplinarity of the Program of Pos-Graduation in Health Science

A dimensão ética do cinema de Walter Salles: hospitalidade, religação e perdão

Soulignant l´importance des transformations du discours politique du cinéma brésilien actuel, cet étude entreprend une analyse de la dimension éthique du cinéma de Walter Salles. Pour cela, nous avons parti de trois films long-métrages du directeur: Terra Estrangeira, Central do Brasil et Abril Despedaçado. Les films sélectionnés constituent les trois diférents chapitres de cette mémoire de maîtrise, qui s´articulent a des diférentes dimensions de l´éthique - l´hospitalité, la réliaison, et le pardon- et se présentent em format essayistique. Au texte, ces dimensions éthiques émergent à partir des récits, surtout des expériences existencielles des protagonistes et de ses singulières rencontres avec l´altérité. Comme tel, dialoguent avec des réflétions d´auteurs comme Edgar Morin, Zigmunt Bauman, Julia Kristeva, Paul Ricoeur et Hannah Arendt. Des diférents régistres de la connaissance -artistique, scientifique, religieuse- s´articulent donc dans le travail, et dialoguent en condition d´égalité. La recherche fait usage de matériels multiples qui incluent, au-delà des films mentionnés, et de ses respectifs scripts, des références à d´autres long-métrages et documentaires du directeur, ainsi que, des makingoffs, entretiens, et interprétations de commentaristes comme Lucia Nagib, Luiz Zanin Oricchio, Ivana Bentes, Pedro Butcher e Jurandir Freire Costa

Professores em contexto formativo: um estudo do processo de mudanças de concepções sobre o ensino da matemática

El objetivo en esta tesis consistió en estudiar el proceso de los cambios de los conceptos de profesores de la educación infantil y de los años iníciales de la educación básica referente a la enseñanza de la matemática. La investigación se desenvolvió en la escuela Presidente Kennedy, en la ciudad de Natal, en Rio Grande do Norte, teniendo como participante 05 (cinco) profesores del curso normal superior a través de la educación superior del instituto relacionado. El trabajo asocia el programa a él Programa de Pós-Graduação em Educação da Universidade Federal do Rio Grande do Norte, en la base de pesquisa Formação e Profissionalização Docente coordinada de los doctores Betânia Leite Ramalho e Isauro Beltran Núñez. El referencial teórico-metodológico en quien si apoya el trabajo se inserta en la señal conceptual usada por Giordan y de Vecchi (1996), de Carrillo y Contreras (1994), Ramalho; Núñez y Gauthier (2003), Ponte (1998), Guimarães (1988), Ernest (1989). En esta investigación, los conceptos de los profesores habían sido estudiados en el contexto educativo de la formación del nivel superior, usándola reflexiva crítico práctico como estrategia formativa. Estos conceptos se entienden como estructuras subyacentes al pensamiento del profesor. Dado la naturaleza del objeto del estudio, la información, para las intenciones de esta investigación, habían sido cosechados a través de los instrumentos siguientes: cuestionario, plan de la lección, entrevista diaria y del campo. El cuestionario fue constituido de preguntas abiertas y de las entrevistas de la mitad-structuralized. La organización de los datos permitió a La inferencia de los conceptos, usando la técnica de la triangulación de datos. La investigación divulgó que los conceptos de los profesores, a través del proceso formativo, se habían desarrollado de una plataforma para otra, yéndose puesto que los modelos didácticos tradicionales para otros modelos dirigidos a una tendencia didáctica de espontaneísta/investigativa. La reflexión crítica era considerada como elemento catalítico de los cambios de los conceptos de los profesores en la educación de las matemáticas, sin embargo déjenos verifican que estos cambios son difíciles de ocurrir para la naturaleza compleja de estos conceptos. Como facilitadores de los factores de estos cambios, encontramos y el investigativo el trabajo, la dinámica y la naturaleza de las actividades se convirtió en el colaborativo de proceso formativo, entre otros. Como obstáculos a los cambios, identificamos el contexto del trabajo de los profesores, de la cultura de los individualistas prácticos de sus profesores de los colegas, del concepto linear, estático y de los mecánicos de los procesos para enseñar, el conocimiento profesional construído durante la formación inicial, alineación con los modelos didácticos de sus viejos profesores, entre otros

Gestão ambiental na saúde pública: um estudo sobre a percepção ambiental de gerenciamento de resíduos sólidos de serviços de saúde, dos servidores do Hospital Universitário Onofre Lopes do Rio Grande do Norte

This research has aimed at studying the perception of University Hospital Onofre Lopes (HUOL) s workers on the environmental management plan of RSSS. They have been interviewed 250 workers: doctors, nurses, nursing assistants, and cleaners. It was used an exploratory and descriptive research of the type Survey, which aims at obtaining of data or information on characteristics, actions or opinions of any group of people. The questions of the questionnaire were of the kind objective", formulated in a model "scale", analyzed in according to the positioning of the interviewee. The wastes of health service have high potential for environmental impact in the activities from HUOL. Actions or environmental protective policy can improve the image of HUOL. They have been detected divergences on the rigor in application of law of ANVISA. The HUOL s workers unaware of the law of ANVISA and they have little or no knowledge about the practices of environmental control, public health and, they do not know the Environmental Management System ISO 14001. They have divergent views on the degree of importance of ISO 14001. There is not a Waste Management Plan for Health Service and / or is not disclosed for most of HUOL workers. It has not carried out audits or defined the goals and objectives. Besides, it has not been identified legal requirements, and there has not been communication about the service is performed or has been made a critical analysis and no control of documents the environmental management plan. The HUOL have not had a committee of environmental management. The direction of HUOL has not been organized courses, training and recycling of waste on environmental control of the health service. On a scale from 01 to 05, the level of aware level concerning to the waste management from health services of the workers, so is at the threshold between 01 and 02. For the reversal of this situation, the first and urgent step is the creation and institutionalization the environmental management committee of the University Hospital Onofre Lopes

Uma modelagem de indicadores de desempenho para instituições de ensino superior no Brasil na abordagem do balanced scorecard: um estudo com instituições privadas

This Master of Science Thesis deals with a BSC modeling for higher education institution focusing on private institution in the Brazilian context. It‟s accomplished a literature review in order to understand the BSC and its application to for profit and non for profit organizations and as a main result it is proposed a BSC conceptual model with a new perspective (Government) and a change in the hierarchy of the main BSC perspective equaling financial to customer/society. Taking the national higher education assessment system of Education Ministry indicators a model is deployed and the relations between the indicators are measured with the Pearson correlation coefficient. As a result a model emerges with sound relations of indicators but a improvement in the financial indicators is needed

Spatial variability of soil penetration resistance influenced by season of sampling

O objetivo deste trabalho foi analizar a distribuição espacial da compactação do solo e a influência da umidade do solo na resistência à penetração. Esta última variável foi descrita pelo índice de cone. O solo estudado foi Nitossolo e os dados de índice de cone foram obtidos usando um penetrômetro. A resistência do solo foi avaliada a 5 profundidades diferentes, 0-10 cm, 10-20 cm, 20-30 cm, 30-40 cm e mais de 40 cm, porém o conteúdo de umidade do solo foi medido a 0-20 cm e 20-40 cm. As condições hídricas do solo variaram nas diferentes amostragems. Os coeficientes de variação para o índice de cone foram 16,5% a 45,8% e os do conteúdo de umidade do solo variaram entre 8,96% e 21,38%. Os resultados sugeriram elevada correlação entre a resistência do solo, estimada pelo índice de cone e a profundidade do solo. Sem embargo, a relação esperada com a umidade do solo não foi apreciada. Observou-se dependência espacial em 31 de 35 séries de dados de índice de cone e umidade do solo. Esta dependência foi ajustada por modelos exponenciais com efeito pepita variável de 0 a 90% o valor do patamar. em séries de dados o comportamento foi aleatório. Portanto, a técnica das distâncias inversas foi utilizada para cartografar a distribuição das variáveis que não tiveram estrutura espacial. Na krigagem constatou-se uma suavização dos mapas comparados com esses das distâncias inversas. A krigagem indicadora foi utilizada para cartografar a variabilidade espacial do índice de cone e recomendar melhor manejo do solo.

Aproveitamento de resíduo de caulim em cerâmica branca

The world market of Kaolin has been growing as new investments for better quality of materials have been applied. This market produces amounts of dross that are put in the environment in a wrong way, causing damages to it. Trying to reduce these damages, researches have been done in an attempt to use kaolin dross in ceramic. The disposal of kaolin dross in the environment by the industries of the states of Rio Grande do Norte and Paraiba have great impact in society. Usually this dross is disposed clandestinely in places like roads, river banks and lands of small cities. The present work shows the characteristics of the kaolin produced by the mining company in Junco do Seridó, Paraiba state, western Seridó, 300 km from Natal, in the border of both states. After that, researches were done to study its physical and the chemistry characteristics, trying to see if it can be used in white ceramic. The samples got were bolted in fabric of 325# . The technological characteristics tried to use it as a product in white ceramic. For that, it was made a haracterization of the subject matter through enlargement analyses, ATG and ATD, elaborating three formulations that were burned in four different temperatures, 1175, 1200, 1250 and 1300 degrees centigrade up to 30 minutes. After the burning, the subjects were submitted to water absorbing tests, linear retreating, apparent porosity, apparent specific mass, resistance to flexibility and MEV. For one of the mixtures it was obtained demanded properties for a semi porous material

Utilização de resíduos de rochas ornamentais na produção de cerâmica branca

The marble and granite waste come from the process of mining of those ornamental rocks for use in the building industry. Brazil is one of the largest producers of blocks or finished products of ornamental rocks, extracting about 5.2 tons / year. The largest national producers are the states of Espírito Santo, Minas Gerais and Bahia which account for 80% of the Brazilian production. However, the waste total amount during processing of these blocks reaches 40% of the total. The use of the waste produced by this industry in white ceramics could be a form of disposition, because these materials, are thrownasa mud directly at decantation ponds, wastelands or in rivers, without any treatment. The present work has as main purpose to study the influence that reject of the ornamental rocks on the physical and mechanical properties of white ceramics. X-Ray characterizations of raw materials by were performed X-Ray fluorescence, X-Ray diffraction, granulometric, thermogravimetric and thermodiferencial analysis, five formulations were made (0, 10, 20, 30, 40% in granite weight) wich were burned at three temperatures: 1100°C, 1150°C and 1200ºC with 60 minutes of sorling time. After sintering, the samples were submitted to different analyser absorption of water, linear retraction, apparent porosity, apparent specific mass, flexival stronght, and scanning were obtained microscopy. Compatible technological properties within the limits demanded for the production of porcelainized stoneware

Obtenção de placas cerâmico a partir de formulações de massas triaxiais de resíduos de caulim, chamote de telha e cinza vegetal

The production of red ceramic is an industrial activity that causes an intense impact. The manufacture of its products considerably increases the demand for natural resources, mainly with the extraction of raw material. The ceramic material produced generates waste, such as ash firewood and chamote. The residue from the beneficiation of kaolin is deposited in a poor, degrades the environment and contaminate water sources and soil, constituting in this manner, ecological disasters. The main objective of this work is to develop the formulation of a ceramic product consisting solely of industrial solid wastes, from ceramic tiles, (chamote) residue of kaolin and ash firewood. It is assumed that this product made in the laboratory can be used in coatings, wall and floor. The aim is to facilitate the replacement of the raw material of original composition of a ceramic body, for waste, while the process of production equal to the conventionally used, so that the properties of the product are reproduced. This work is characterized waste as its chemical composition, analysis of particle size, X-ray diffraction and thermal behavior. Several formulations were studied. The mass of waste was prepared by dry process, pressed to 25 MPa, and then burned in muffle type oven to 850, 950, 1050 and 1150 °C. The results showed that it is technically possible to produce porous tiles only with waste. It was found that the formulations of bodies play a key role in the properties of the final product, as well as the sintering temperature and heating rates. RN in the waste of kaolin is estimated at 15,000 t/month, about 3,000 gray t/month and chamote with 10 million pieces/month damaged. The presence of carbonates of calcium and magnesium at 1050 ° C results in an appropriate porosity and mechanical strength. The formulation M3JE, composed of 69% waste of kaolin, 7.7% and 23.3% of chamote of gray, became suitable for porous materials with the strength and absorption within the level of national and international standards

Produção de grês porcelanato a partir de matérias-primas do Rio Grande do Norte e queima a gás natural

The State of Rio Grande do Norte, Brazil, possess major deposits of feldspar, clay, kaolin and talc, all raw materials used in the production of porcelainized stoneware tiles. Conversely, state industries manufacture only low added value red ceramics. Porcelainized stoneware tiles is one of the noblest ceramics, depicting low water absorption (typically below of 0,5%), in addition to excellent staining resistance and mechanical strength. The present work aims at investigating the potential of local raw materials for the production of porcelainized stoneware tiles. To that end, these materials were characterized by X-ray fluorescence, X-ray diffraction, particle size analysis, thermal gravimetric analysis and thermal differential analysis. Admixtures containing different compositions were prepared and fired at three temperatures, 1150, 1200 and 1250°C for 30 min. After firing, tests samples were characterized by water absorption tests, linear retraction, dilatometric analysis, apparent porosity, apparent specific mass, flexural strength, and microstructural analysis by XRD and SEM. The results revealed that ceramics with porcelainized stoneware tiles characteristics could be produced from raw materials originated in the State of Rio Grande do Norte