Technical note : modelling a complex micro-multileaf collimator using the standard BEAMnrc distribution

Purpose: The component modules in the standard BEAMnrc distribution may appear to be insufficient to model micro-multileaf collimators that have tri-faceted leaf ends and complex leaf profiles. This note indicates, however, that accurate Monte Carlo simulations of radiotherapy beams defined by a complex collimation device can be completed using BEAMnrc's standard VARMLC component module.---------- Methods: That this simple collimator model can produce spatially and dosimetrically accurate micro-collimated fields is illustrated using comparisons with ion chamber and film measurements of the dose deposited by square and irregular fields incident on planar, homogeneous water phantoms.---------- Results: Monte Carlo dose calculations for on- and off-axis fields are shown to produce good agreement with experimental values, even upon close examination of the penumbrae.--------- Conclusions: The use of a VARMLC model of the micro-multileaf collimator, along with a commissioned model of the associated linear accelerator, is therefore recommended as an alternative to the development or use of in-house or third-party component modules for simulating stereotactic radiotherapy and radiosurgery treatments. Simulation parameters for the VARMLC model are provided which should allow other researchers to adapt and use this model to study clinical stereotactic radiotherapy treatments.

Use of micro-ATR/FTIR imaging to study heterogeneous polymer oxidation by direct solvent casting onto the ATR IRE

A technique is described whereby micro-ATR/FTIR imaging can be used to follow polymer degradation reactions in situ in real time. The internal reflection element (IRE) assembly is removed from the ATR objective and polymer is solvent cast directly onto the IRE surface. The polymer is then subjected to degradation conditions and molecular structural changes monitored by periodically replacing the IRE assembly back in the ATR objective and collecting spectra which can be used to construct images. This approach has the benefit that the same part of the sample is always studied, and that contact by pressure which might damage the polymer surface is not required. The technique is demonstrated using the polymer Topas which was degraded by exposure to UVC light in air.

Channel blurring and consumer expectations : evidence in Chile

An important trend in Chilean retailing industry is the increase in channel blurring. This investigation attempts to identify the relevant store attributes for different retail formats (grocery, department store, drug store, and home improvement). Do consumer store attribute saliency vary for different retail formats? Interviews identified twelve salient store attributes for the different retail formats. Survey results showed differences in store attribute saliencies for consumers when shopping at different formats. Seven of the twelve variables showed significant differences across formats. However, two attributes were relatively important for all four retail formats: product quality and responsiveness of employees.

Modelling the broadband wireless channel in rural Australia

The internet infrastructure which supports high data rates has a major impact on the Australian economy and the world. However, in rural Australia, the provision of broadband services to an internet dispersed population over a large geographical area with low population densities remains both an economic and technical challenge [1]. Furthermore, the implementation of currently available technologies such as fibre-to-the-premise (FTTP), 3G, 4G and WiMAX seems to be impractical, considering the low population density that is distributed in a large area. Therefore, new paradigms and innovative telecommunication technologies need to be explored to overcome the challenges of providing faster and more reliable broadband internet services to internet dispersed rural areas. The research project implements an innovative Multi-User- Single-Antenna for MIMO (MUSA-MIMO) technology using the spectrum currently allocated to analogue TV. MUSAMIMO technology can be considered as a special case of MIMO technology, which is beneficial when provisioning reliable and high-speed communication channels. Particularly, the abstract describes the development of a novel MUSA-MIMO channel model that takes into account temporal variations in the rural wireless environment. This can be considered as a novel approach tailor-made to rural Australia for provisioning efficient wireless broadband communications.

Channel tracking algorithms for highly efficient wireless broadband communications in rural areas

High-speed broadband internet access is widely recognised as a catalyst to social and economic development, having a significant impact on global economy. Rural Australia’s inherent dispersed population over a large geographical area make the delivery of efficient, well-maintained and cost-effective internet a challenging task. The novel and highly-efficient Multi-User-Single-Antenna for MIMO (MUSA-MIMO) broadband wireless communication technology can effectively be used to deliver wireless broadband access to rural areas. This research aims to develop for the first time, an efficient and accurate algorithm for the tracking and prediction of Channel State Information (CSI) at the transmitter, by characterising time variation effects of the wireless communication channel on the performance of a highly-efficient MUSA-MIMO technology particularly suited for rural communities, improving their quality of life and economic prosperity.

Micro-family-owned business : transitory survival mechanism or long term wealth creator?

Principal Topic: Entrepreneurship is key to employment, innovation and growth (Acs & Mueller, 2008), and as such, has been the subject of tremendous research in both the economic and management literatures since Solow (1957), Schumpeter (1934, 1943), and Penrose (1959). The presence of entrepreneurs in the economy is a key factor in the success or failure of countries to grow (Audretsch and Thurik, 2001; Dejardin, 2001). Further studies focus on the conditions of existence of entrepreneurship, influential factors invoked are historical, cultural, social, institutional, or purely economic (North, 1997; Thurik 1996 & 1999). Of particular interest, beyond the reasons behind the existence of entrepreneurship, are entrepreneurial survival and good ''performance'' factors. Using cross-country firm data analysis, La Porta & Schleifer (2008) confirm that informal micro-businesses provide on average half of all economic activity in developing countries. They find that these are utterly unproductive compared to formal firms, and conclude that the informal sector serves as a social security net ''keep[ing] millions of people alive, but disappearing over time'' (abstract). Robison (1986), Hill (1996, 1997) posit that the Indonesian government under Suharto always pointed to the lack of indigenous entrepreneurship , thereby motivating the nationalisation of all industries. Furthermore, the same literature also points to the fact that small businesses were mostly left out of development programmes because they were supposed less productive and having less productivity potential than larger ones. Vial (2008) challenges this view and shows that small firms represent about 70% of firms, 12% of total output, but contribute to 25% of total factor productivity growth on average over the period 1975-94 in the industrial sector (Table 10, p.316). ---------- Methodology/Key Propositions: A review of the empirical literature points at several under-researched questions. Firstly, we assess whether there is, evidence of small family-business entrepreneurship in Indonesia. Secondly, we examine and present the characteristics of these enterprises, along with the size of the sector, and its dynamics. Thirdly, we study whether these enterprises underperform compared to the larger scale industrial sector, as it is suggested in the literature. We reconsider performance measurements for micro-family owned businesses. We suggest that, beside productivity measures, performance could be appraised by both the survival probability of the firm, and by the amount of household assets formation. We compare micro-family-owned and larger industrial firms' survival probabilities after the 1997 crisis, their capital productivity, then compare household assets of families involved in business with those who do not. Finally, we examine human and social capital as moderators of enterprises' performance. In particular, we assess whether a higher level of education and community participation have an effect on the likelihood of running a family business, and whether it has an impact on households' assets level. We use the IFLS database compiled and published by RAND Corporation. The data is a rich community, households, and individuals panel dataset in four waves: 1993, 1997, 2000, 2007. We now focus on the waves 1997 and 2000 in order to investigate entrepreneurship behaviours in turbulent times, i.e. the 1997 Asian crisis. We use aggregate individual data, and focus on households data in order to study micro-family-owned businesses. IFLS data covers roughly 7,600 households in 1997 and over 10,000 households in 2000, with about 95% of 1997 households re-interviewed in 2000. Households were interviewed in 13 of the 27 provinces as defined before 2001. Those 13 provinces were targeted because accounting for 83% of the population. A full description of the data is provided in Frankenberg and Thomas (2000), and Strauss et alii (2004). We deflate all monetary values in Rupiah with the World Development Indicators Consumer Price Index base 100 in 2000. ---------- Results and Implications: We find that in Indonesia, entrepreneurship is widespread and two thirds of households hold one or several family businesses. In rural areas, in 2000, 75% of households run one or several businesses. The proportion of households holding both a farm and a non farm business is higher in rural areas, underlining the reliance of rural households on self-employment, especially after the crisis. Those businesses come in various sizes from very small to larger ones. The median business production value represents less than the annual national minimum wage. Figures show that at least 75% of farm businesses produce less than the annual minimum wage, with non farm businesses being more numerous to produce the minimum wage. However, this is only one part of the story, as production is not the only ''output'' or effect of the business. We show that the survival rate of those businesses ranks between 70 and 82% after the 1997 crisis, which contrasts with the 67% survival rate for the formal industrial sector (Ter Wengel & Rodriguez, 2006). Micro Family Owned Businesses might be relatively small in terms of production, they also provide stability in times of crisis. For those businesses that provide business assets figures, we show that capital productivity is fairly high, with rates that are ten times higher for non farm businesses. Results show that households running a business have larger family assets, and households are better off in urban areas. We run a panel logit model in order to test the effect of human and social capital on the existence of businesses among households. We find that non farm businesses are more likely to appear in households with higher human and social capital situated in urban areas. Farm businesses are more likely to appear in lower human capital and rural contexts, while still being supported by community participation. The estimation of our panel data model confirm that households are more likely to have higher family assets if situated in urban area, the higher the education level, the larger the assets, and running a business increase the likelihood of having larger assets. This is especially true for non farm businesses that have a clearly larger and more significant effect on assets than farm businesses. Finally, social capital in the form of community participation also has a positive effect on assets. Those results confirm the existence of a strong entrepreneurship culture among Indonesian households. Investigating survival rates also shows that those businesses are quite stable, even in the face of a violent crisis such as the 1997 one, and as a result, can provide a safety net. Finally, considering household assets - the returns of business to the household, rather than profit or productivity - the returns of business to itself, shows that households running a business are better off. While we demonstrate that uman and social capital are key to business existence, survival and performance, those results open avenues for further research regarding the factors that could hamper growth of those businesses in terms of output and employment.

Fit optimisation of a distal medial tibia plate

An iterative method for the fit optimisation of a pre-contoured fracture fixation plate for a given bone data set is presented. Both plate shape optimisation and plate fit quantification are conducted in a virtual environment utilising computer graphical methods and 3D bone and plate models. Two optimised shapes of the undersurface of an existing distal medial tibia plate were generated based on a dataset of 45 3D bone models reconstructed from computed tomography image data of Japanese tibiae. The existing plate shape achieved an anatomical fit on 13% of tibiae from the dataset. Modified plate 1 achieved an anatomical fit for 42% and modified plate 2 a fit for 67% of the bones. If either modified plate 1 or plate 2 is used, then the anatomical fit can be increased to 82% for the same dataset. Issues pertaining to any further improvement in plate fit/shape are discussed.

Corruption and political interest : empirical evidence at the micro level

The topic of corruption has recently attracted a great deal of attention, yet there is still a lack of micro level empirical evidence regarding the determinates of corruption. Furthermore, the present literature has not investigated the effects of political interest on corruption despite the interesting potential of this link. We address these deficiencies by analysing a cross-section of individuals, using the World Values Survey. We explore the determinants of corruption through two dependant variables (perceived corruption and the justifiability of corruption). The impact of political interest on corruption is explored through three different proxies presenting empirical evidence at both the cross-country level and the within-country level.The results of the multivariate analysis suggest that political interest has an impact on corruption controlling for a huge number of factors.

Chemical functionalities of high and low sulfur Australian coals : a case study using micro attenuated total reflectance–fourier transform infrared (ATR–FTIR) spectrometry

The macerals in bituminous coals with varying organic sulfur content from the Early Permian Greta Coal Measures at three locations (Southland Colliery, Drayton Colliery and the Cranky Corner Basin), in and around the Sydney Basin (Australia), have been studied using light-element electron microprobe (EMP) analysis and micro-ATR–FTIR. Electron microprobe analysis of individual macerals reveals that the vitrinite in both the Cranky Corner Basin and Drayton Colliery (Puxtrees seam) samples have similar carbon contents (ca. 78% C in telocollinite), suggesting that they are of equivalent rank. However, the Cranky Corner coals have anomalously low vitrinite reflectance (down to 0.45%) vs. the Drayton materials (ca. 0.7%). They also have very high organic S content (3–6.5%) and lower O content (ca. 10%) than the equivalent macerals in the Drayton sample (0.7% S and 15.6% O). A study was carried out to investigate the impacts of the high organic S on the functional groups of the macerals in these two otherwise iso-rank, stratigraphically-equivalent seams. An iso-rank low-S coal from the overlying Wittingham Coal Measures near Muswellbrook and coals of slightly higher rank from the Greta Coal Measures at Southland Colliery near Cessnock were also evaluated using the same techniques to extend the data set. Although the telocollinite in the Drayton and Cranky Corner coals have very similar carbon content (ca.78% C), the ATR–FTIR spectra of the vitrinite and inertinite macerals in these respectively low S and high S coals show some distinct differences in IR absorbance from various aliphatic and aromatic functional groups. The differences in absorbance of the aliphatic stretching bands (2800–3000 cm−1) and the aromatic carbon (CC) peak at 1606 cm−1 are very obvious. Compared to that of the Drayton sample (0.7% S and 15% O), the telocollinite of the Cranky Corner coal (6% S and 10% O) clearly shows: (i) less absorbance from OH groups, represented by a broad region around 3553 cm−1, (ii) much stronger aliphatic C–H absorbance (stretching modes around 3000–2800 cm−1 and bending modes around 1442 cm−1) and (iii) less absorbance from aromatic carbon functional groups (peaking at 1606 cm−1). Evaluation of the iso-rank Drayton and Cranky Corner coals shows that: (i) the aliphatic C–H absorbances decrease with increasing oxygen content but increase with increasing organic S content and (ii) the aromatic H to aliphatic H ratio (Har/Hali) for the telocollinite increases with (organic) O%, but decreases progressively with increasing organic S. The high organic S content in the maceral appears to be accompanied by a greater proportion of aliphatic functional groups, possibly as a result of some of the O within maceral ring structures in the high S coal samples being replaced.

Experimental studies on the shear behaviour and strength of LiteSteel Beams

This paper presents the details of an experimental study on the shear behaviour and strength of a recently developed, cold-formed steel hollow flange channel beam known as LiteSteel Beam (LSB). The new LSB sections with rectangular hollow flanges are produced using a patented manufacturing process involving simultaneous cold-forming and dual electric resistance welding. They are commonly used as flexural members in buildings. However, no research has been undertaken on the shear behaviour of LSBs. Therefore a detailed experimental study involving 36 shear tests was undertaken to investigate the shear behaviour of 10 different LSB sections. Simply supported test specimens of LSBs with aspect ratios of 1.0 and 1.5 were loaded at midspan until failure using both single and back to back LSB arrangements. Test specimens were chosen such that all three types of shear failure (shear yielding, inelastic and elastic shear buckling) occurred in the tests. Comparison of experimental results with corresponding predictions from the current Australian and North American cold-formed steel design rules showed that the current design rules are very conservative for the shear design of LSBs. Significant improvements to web shear buckling occurred due to the presence of rectangular hollow flanges while considerable post-buckling strength was also observed. Appropriate improvements have been proposed for the shear strength of LSBs based on the design equations in the North American Specification. This paper presents the details of this experimental study and the results. When reduced height web side plates or only one web side plate was used, the shear capacity of LSB was reduced. Details of these tests and the results are also presented in this paper. Keywords: LiteSteel beam, Shear strength, Shear tests, Cold-formed steel structures, Direct strength method, Slender web, Hollow flanges.

Development of a multi-scale finite element model of the osteoporotic lumbar vertebral body for the investigation of apparent level vertebra mechanics and micro-level trabecular mechanics.

Osteoporotic spinal fractures are a major concern in ageing Western societies. This study develops a multi-scale finite element (FE) model of the osteoporotic lumbar vertebral body to study the mechanics of vertebral compression fracture at both the apparent (whole vertebral body) and micro-structural (internal trabecular bone core)levels. Model predictions were verified against experimental data, and found to provide a reasonably good representation of the mechanics of the osteoporotic vertebral body. This novel modelling methodology will allow detailed investigation of how trabecular bone loss in osteoporosis affects vertebral stiffness and strength in the lumbar spine.

Flexural behaviour and design of hollow flange steel beams

The LiteSteel Beam (LSB) is a new hollow flange channel section developed by OneSteel Australian Tube Mills using a patented Dual Electric Resistance Welding technique. The LSB has a unique geometry consisting of torsionally rigid rectangular hollow flanges and a relatively slender web. It is commonly used as rafters, floor joists and bearers and roof beams in residential, industrial and commercial buildings. It is on average 40% lighter than traditional hot-rolled steel beams of equivalent performance. The LSB flexural members are subjected to a relatively new Lateral Distortional Buckling mode, which reduces the member moment capacity. Unlike the commonly observed lateral torsional buckling of steel beams, lateral distortional buckling of LSBs is characterised by simultaneous lateral deflection, twist and web distortion. Current member moment capacity design rules for lateral distortional buckling in AS/NZS 4600 (SA, 2005) do not include the effect of section geometry of hollow flange beams although its effect is considered to be important. Therefore detailed experimental and finite element analyses (FEA) were carried out to investigate the lateral distortional buckling behaviour of LSBs including the effect of section geometry. The results showed that the current design rules in AS/NZS 4600 (SA, 2005) are over-conservative in the inelastic lateral buckling region. New improved design rules were therefore developed for LSBs based on both FEA and experimental results. A geometrical parameter (K) defined as the ratio of the flange torsional rigidity to the major axis flexural rigidity of the web (GJf/EIxweb) was identified as the critical parameter affecting the lateral distortional buckling of hollow flange beams. The effect of section geometry was then included in the new design rules using the new parameter (K). The new design rule developed by including this parameter was found to be accurate in calculating the member moment capacities of not only LSBs, but also other types of hollow flange steel beams such as Hollow Flange Beams (HFBs), Monosymmetric Hollow Flange Beams (MHFBs) and Rectangular Hollow Flange Beams (RHFBs). The inelastic reserve bending capacity of LSBs has not been investigated yet although the section moment capacity tests of LSBs in the past revealed that inelastic reserve bending capacity is present in LSBs. However, the Australian and American cold-formed steel design codes limit them to the first yield moment. Therefore both experimental and FEA were carried out to investigate the section moment capacity behaviour of LSBs. A comparison of the section moment capacity results from FEA, experiments and current cold-formed steel design codes showed that compact and non-compact LSB sections classified based on AS 4100 (SA, 1998) have some inelastic reserve capacity while slender LSBs do not have any inelastic reserve capacity beyond their first yield moment. It was found that Shifferaw and Schafer’s (2008) proposed equations and Eurocode 3 Part 1.3 (ECS, 2006) design equations can be used to include the inelastic bending capacities of compact and non-compact LSBs in design. As a simple design approach, the section moment capacity of compact LSB sections can be taken as 1.10 times their first yield moment while it is the first yield moment for non-compact sections. For slender LSB sections, current cold-formed steel codes can be used to predict their section moment capacities. It was believed that the use of transverse web stiffeners could improve the lateral distortional buckling moment capacities of LSBs. However, currently there are no design equations to predict the elastic lateral distortional buckling and member moment capacities of LSBs with web stiffeners under uniform moment conditions. Therefore, a detailed study was conducted using FEA to simulate both experimental and ideal conditions of LSB flexural members. It was shown that the use of 3 to 5 mm steel plate stiffeners welded or screwed to the inner faces of the top and bottom flanges of LSBs at third span points and supports provided an optimum web stiffener arrangement. Suitable design rules were developed to calculate the improved elastic buckling and ultimate moment capacities of LSBs with these optimum web stiffeners. A design rule using the geometrical parameter K was also developed to improve the accuracy of ultimate moment capacity predictions. This thesis presents the details and results of the experimental and numerical studies of the section and member moment capacities of LSBs conducted in this research. It includes the recommendations made regarding the accuracy of current design rules as well as the new design rules for lateral distortional buckling. The new design rules include the effects of section geometry of hollow flange steel beams. This thesis also developed a method of using web stiffeners to reduce the lateral distortional buckling effects, and associated design rules to calculate the improved moment capacities.