Shoot growth of Merlot and Cabernet Sauvignon grapevine varieties

The objective of this work was to evaluate shoot growth of the grapevine varieties Merlot and Cabernet Sauvignon, during 2006/2007, and Cabernet Sauvignon, during 2008/2009, in São Joaquim, SC, Brazil. The experiment was carried out in a commercial vineyard trained on a vertical trellis system. The shoots of the central part of the plants were selected, and the lengths from the base to the apex of 20 shoots per cultivar were evaluated. In 2006/2007, monitoring began at pruning, on 9/15/2006, and ended on 2/6/2007, totalizing 144 days of evaluation. During the 2008/2009 cycle, phenology and shoot growth for 'Cabernet Sauvignon' were assessed from grape development (1/13/2009) (pea-sized grapes) until shoot vegetative growth had ceased. Budburst occurred in the second half of September, and shoot-growth cessation occurred during ripening. Higher growth rates (about 4 cm per day) were observed in pre- and post-flowering, followed by reduction due to the competition for photosynthates for the formation of flowers and bunches. Temperature and photoperiod induce grapevine shoots to cease growth in the highland regions of Santa Catarina State, Brazil.

Short-term storage in vitro and large-scale propagation of grapevine genotypes

The objective of this work was to evaluate the large-scale propagation of grapevine genotypes after short-term storage in vitro. Microshoots from ten grapevine genotypes were used. The following storage temperatures were evaluated: 10, 20, and 25°C. After short-term storage, the shoots were propagated in up to five successive subcultures, to assess the large-scale propagation of the germplasm maintained under conditions of minimal growth. The propagated shoots were rooted in different concentrations of indolbutiric acid (IBA) and acclimatized in greenhouse. The best temperature for short-term storage in vitro and survival of the genotypes was 20°C. In the propagation phase, the highest number of shoots per explant was found in the subcultures 4 and 5, with averages of 4.9 and 4.8 shoots per explant, respectively. In the rooting phase, the best results for number of roots were obtained using a culture medium supplemented with 0.4 µmol L-1 of IBA, with an average of three roots per shoot. During the acclimation phase, a survival rate higher than 95% was achieved after 30 days in the greenhouse. Grapevine genotypes maintained for six months in vitro, at 20ºC, can be micropropagated in large scale.

Effect of thinning on stem form and wood characteristics of teak (Tectona grandis) in a humid tropical site in Costa Rica

Abstract

Influence of rootstocks and pruning times on yield and on nutrient content and extraction in 'Niagara Rosada' grapevine

The objective of this work was to evaluate the influence of rootstocks and pruning times on yield and on nutrient content and extraction by pruned branches and harvested bunches of 'Niagara Rosada' grapevine in subtropical climate. The rootstocks 'IAC 766', 'IAC 572', 'IAC 313', 'IAC 571-6', and '106-8 Mgt' were evaluated. Treatments consisted of a combination between five rootstocks and three pruning times. At pruning, fresh and dry matter mass of branches were evaluated to estimate biomass accumulation. At harvest, yield was estimated by weighing of bunches per plant. Branches and bunches were sampled at pruning and at harvest, respectively, for nutrient content analysis. Nutrient content and dry matter mass of branches and bunches were used to estimate total nutrient extraction. 'Niagara Rosada' grapevine grafted onto the 'IAC 572' rootstock had the highest yield and dry matter mass of bunches, which were significantly different from the ones observed in 'Niagara Rosada'/'IAC 313'. 'Niagara Rosada' grafted onto the 'IAC 572' rootstock extracted the largest quantity of K, P, Mg, S, Cu, and Fe, differing from 'IAC 313' and 'IAC 766' in K and P extraction, and from '106-8 Mgt' in Mg and S extraction. Winter pruning results in higher yield, dry matter accumulation by branches, and total nutrient content and extraction.

Wood ants use resin to protect themselves against pathogens

Social life is generally associated with an increased exposure to pathogens and parasites, due to factors such as high population density, frequent physical contact and the use of perennial nest sites. However, sociality also permits the evolution of new collective behavioural defences. Wood ants, Formica paralugubris, commonly bring back pieces of solidified coniferous resin to their nest. Many birds and a few mammals also incorporate green plant material into their nests. Collecting plant material rich in volatile compounds might be an efficient way to fight bacteria and fungi. However, no study has demonstrated that this behaviour has a positive effect on survival. Here, we provide the first experimental evidence that animals using plant compounds with antibacterial and antifungal properties survive better when exposed to detrimental micro-organisms. The presence of resin strongly improves the survival of F. paralugubris adults and larvae exposed to the bacteria Pseudomonas fluorescens, and the survival of larvae exposed to the entomopathogenic fungus Metarhizium anisopliae. These results show that wood ants capitalize on the chemical defences which have evolved in plants to collectively protect themselves against pathogens.

Cutting of Frozen Wood

The objective of this master's thesis was to develop a system for measuring the cutting forces of frozen wood. In northern parts of the world cuttingof frozen wood is one of the major problem. During winter and early spring the temperature inside the wood cells will fall below Zero degrees that strongly influences on the properties of the wood. These variations of properties will effects on the blade nomenclature while cutting the frozen wood. However the end results will cause uneven cutting forces. Cutting forces, Chip formation, wearing of the blade and the quality of the machined surface are difficult task. In this project we are attempting to find the variation of cutting forces and properties of frozen wood at four different temperatures (-20 , -10, 0 and + 10 degrees). The linear planning machine was used for measuring the cuttingforces. The cutting was done parallel to the long axis of wood due to the nature of pine wood and the structure of the plane. A considerable amount of work andtime was used for collecting and processing the numerical information from the sensors of the measuring system. There were some alterations suggested to the construction of the plane and the sensor system.

Root distribution of irrigated grapevine rootstocks in a coarse texture soil of the São Francisco Valley, Brazil

An experiment was carried out to determine the root distribution of four grapevine rootstocks (Salt Creek, Dogridge, Courdec 1613, IAC 572) in a coarse texture soil of a commercial growing area in Petrolina County, São Francisco Valley, Brazil. Rootstocks were grafted to a seedless table grape cv. Festival, and irrigated by microsprinkler. Roots were quantified by the trench wall method aided by digital image analysis. Results indicated that roots reached 1 m depth, but few differences among rootstocks were found. All of them presented at least 90 % of the roots distributed until 0.6 m depth, with a greater root presence in the first 0.4 m. The upper 0.6 m can be taken into account as the effective rooting depth for soil and water management.

A Feasibility Study of a Pelleting Plant as an Option for By Product Upgrading in Wood-Processing Industry

Tämän kannattavuustutkimuksen lähtökohtana oli se, että Yhtyneet Sahat Oy:n Kaukaan sahalla ja Luumäen jatkojalostuslaitoksella haluttiin selvittää pellettitehtaan kannattavuus nykyisessä markkinatilanteessa. Tämä työon luonteeltaan teknis-taloudellinen selvitys eli ns. feasibility study. Pelletöintiprosessi on tekniikaltaan yksinkertainen eikä edellytä korkea teknologian laitteita. Toimiala on maailmanlaajuisesti varsin uusi. Suomessa pellettimarkkinat ovat vielä pienet ja kehittymättömät, mutta kasvua on viime vuosina tapahtunut. Valtaosa kotimaan tuotannosta menee vientiin. Investoinnin laskentaprosessissa saadut tuotannon alkuarvot sekä kustannusrakenteen määrittelyt ovat perustana varsinaisille kannattavuuslaskelmille. Laskelmista on selvitetty investointeihin liittyvät yleisimmät taloudelliset tunnusluvut ja herkimpiä muuttujia on tutkittu ja pohdittu herkkyysanalyysiä apuna käyttäen.

Propagation of the Ignition Front against Airflow in Packed Beds of Wood Particles

Combustion of wood is increasing because of the needs of decreasing the emissions of carbon dioxide and the amount of waste going to landfills. Wood based fuels are often scattered on a large area. The transport distances should be short enough to prevent too high costs, and so the size of heating and power plants using wood fuels is often rather small. Combustion technologies of small-size units have to be developed to reach efficient and environmentally friendly energy production. Furnaces that use different packed bed combustion or gasification techniques areoften most economic in small-scale energy production. Ignition front propagation rate affects the stability, heat release rate and emissions of packed bed combustion. Ignition front propagation against airflow in packed beds of wood fuels has been studied. The research has been carried out mainly experimentally. Theoretical aspects have been considered to draw conclusions about the experimental results. The effects of airflow rate, moisture content of the fuel, size, shape and density of particles, and porosity of the bed on the propagation rate of the ignition front have been studied. The experiments were carried out in a pot furnace. The fuels used in the experiments were mainly real wood fuels that are often burned in the production of energy. The fuel types were thin wood chips, saw dust, shavings, wood chips, and pellets with different sizes. Also a few mixturesof the above were tested. Increase in the moisture content of the fuel decreases the propagation rates of the ignition front and makes the range of possible airflow rates narrower because of the energy needed for the evaporation of water and the dilution of volatile gases due to evaporated steam. Increase in the airflow rate increases the ignition rate until a maximum rate of propagation is reached after which it decreases. The maximum flame propagation rate is not always reached in stoichiometric combustion conditions. Increase in particle size and density transfers the optimum airflow rate towards fuel lean conditions. Mixing of small and large particles is often advantageous, because small particles make itpossible to reach the maximum ignition rate in fuel rich conditions, and large particles widen the range of possible airflow rates. A correlation was found forthe maximum rate of ignition front propagation in different wood fuels. According to the correlation, the maximum ignition mass flux is increased when the sphericity of the particles and the porosity of the bed are increased and the moisture content of the fuel is decreased. Another fit was found between sphericity and porosity. Increase in sphericity decreases the porosity of the bed. The reasons of the observed results are discussed.

Short communication.Wood identification based on their common name and their transversal surface anatomy. Application to the batch from the expedition of Ruiz and Pavon

Aim of study: To identify species of wood samples based on common names and anatomical analyses of their transversal surfaces (without microscopic preparations). Area of study: Spain and South America Material and methods: The test was carried out on a batch of 15 lumber samples deposited in the Royal Botanical Garden in Madrid, from the expedition by Ruiz and Pavon (1777-1811). The first stage of the methodology is to search and to make a critical analysis of the databases which list common nomenclature along with scientific nomenclature. A geographic filter was then applied to the information resulting from the samples with a more restricted distribution. Finally an anatomical verification was carried out with a pocket microscope with a magnification of x40, equipped with a 50 micrometers resolution scale. Main results: The identification of the wood based exclusively on the common name is not useful due to the high number of alternative possibilities (14 for “naranjo”, 10 for “ébano”, etc.). The common name of one of the samples (“huachapelí mulato”) enabled the geographic origin of the samples to be accurately located to the shipyard area in Guayaquil (Ecuador). Given that Ruiz y Pavon did not travel to Ecuador, the specimens must have been obtained by Tafalla. It was possible to determine correctly 67% of the lumber samples from the batch. In 17% of the cases the methodology did not provide a reliable identification. Research highlights: It was possible to determine correctly 67% of the lumber samples from the batch and their geographic provenance. The identification of the wood based exclusively on the common name is not useful.

Anatomy, chlorophyll content and photosynthetic potential in grapevine leaves under plastic cover

The present study evaluated the anatomy, chlorophyll content and photosynthetic potential of grapevine leaves grown under plastic cover. The experiment was carried out in vineyards of Moscato Giallo cultivar covered and uncovered with plastic. A block design with 10 selected plants was used for each area (covered and uncovered). Twelve leaves (six of them fully exposed to solar radiation and six grown under shaded conditions) were collected from each area and were fixed and analyzed microscopically (thickness of the adaxial and abaxial epidermis and of the palisade and spongy parenchymas). Chlorophyll content and photosynthetic potential were determined in the vineyard at veraison and after harvest. Plastic covering increased the thickness of the palisade parenchyma in exposed and shaded leaves due to solar radiation restriction. However, the leaves from the covered vineyard did not have the same response to the restriction of solar radiation, as observed in the uncovered vineyard. The thickness of the adaxial and abaxial epidermis and of the spongy parenchyma did not vary due to solar radiation restriction. Chlorophyll content increased in the leaves of covered plants. The photosynthetic potential of the vines is not affected by solar radiation restriction imposed by plastic cover due to anatomical modification in leaves.

Wood Volume Measurement Using Color Images

Tämä työ käsittelee puutukkien tilavuuden mittaamista värikonenäön avulla. Värikuvat on saatu Simpeleellä olevan metsäteollisuusyrityksen hiomosta. Työssä esitetään perusteellisesti matemaattinen teoria, joka liittyy käytettyihin kuvankäsittelymenetelmiin, kuten luokitteluun, kohinan poistoon ja tukkien segmentointiin. Esitetyt menetelmät implementointiin käytännössä ja eri menetelmillä saatuja tuloksia vertailtiin keskenään. Kuvankäsittelyalgoritmit on implementoitu Matlab 6.0:n avulla. Pääasiassa käytettiin uusinta Image Processing Toolboxia, joka on versio 3.0. Tämä työn näkökulma on pääasiassa käytäntöön soveltava, koska metsäteollsuus on korkealla tasolla Suomessa ja siellä on paljon alan yrityksiä, joissa tässä työssä kehitettyä menetelmää voidaan hyödyntää.

Removal of Lipophilic Wood Extractives from TMP Process Waters by Wet Oxidation

Työssä tutkittiin kokeellisesti rasvaliukoisten uuteaineiden poistamista TMP -prosessin vesikierroista märkähapetuksen avulla. Työn tavoitteena oli tutkia mahdollisuudet hyödyntää TMP -prosessissa vallitsevaa korkeaa lämpötilaa rasvaliukoisten uuteaineiden poistamiseen hapettamalla niitä puhtaalla hapella. Kirjallisuusosassa tarkasteltiin märkähapetuksen teknologiaa, reaktiomekanismia, käytettyjä katalyyttejä, käyttökohteita sekä kustannuksia. Kokeita suoritettiin autoklaavireaktorissa lämpötiloissa 140 °C, 160 °C ja 180 °C. Vetyperoksidia käytettiin katalyyttinä lisätyn vetyperoksidin määrän ollessa 100 - 1800 mg/l ja hapen osapaineen ollessa 0 ( typpiatmosfääri) - 15 baria. Kokeissa tarkasteltiin kemiallisen hapenkulutuksen (COD), rasvaliukoisten uuteaineiden konsentraation, orgaanisen kokonaishiilen (TOC) ja värin muutoksia kokeiden aikana eri lämpötiloilla, hapen osapaineilla ja lisätyn vetyperoksidin määrillä. Kokeissa saavutettiin 30 %:n COD:n vähenemä sekä 90 %:n vähenemä rasvaliukoisissa uuteaineissa lämpötiloissa 160 °C ja 180 °C. Lisäämällä vetyperoksidia katalyyttinä saavutettiin lähes sama tulos lämpötilassa 140 °C. Suurin tässä työssä havaittu ongelma oli lisääntynyt värinmuodostus vedessä olevassa hienojakoisessa kiintoaineessa hapetuksen aikana. Tämän vuoksi lisätutkimukset ovat tarpeellisia sen seikan selvittämiseksi, voidaanko muodostunut väri mahdollisesti poistaa massan valkaisussa.

Potential Acquisition Candidates for a Supplier of Wood Processing Machinery

Diplomityön tavoitteena oli sopivimman yritysostokohteen valitseminen useiden kilpailijoiden joukosta puunkäsittelykoneiden toimittajalle. Ensin esiteltiin Suomen metsäteollisuus sekä sen osaamistarpeista noussut metsäklusteri pääosin kohdeyrityksen näkökulmasta. Seuraavaksi annettiin kuva yrityksen tuotteista, kilpailijoista ja asiakkaista. Yritysostoprosessi kuvattiin sekä esille tuotiin yleiset motiivit ja kriittiset menestystekijät. Lisäksi kuvattiin kilpailijoiden ja liiketoimintaympäristön analysointi yrityksen menestyksen edellytyksenä. Puuntyöstökoneiden markkinat segmentoitiin ja analysoitiin vuodesta 1990 aina tähän päivään asti, jotta löydettäisiin kehityskelpoiset osa-alueet eli alueet, joissa yrityksen markkinaosuutta voitaisiin kasvattaa. Kandidaattien ominaisuuksia verrattiin yritysoston motiiveihin. Yritysten tuotteet sekä maantieteellinen sijainti pisteytettiin, jotta sopivimmat yritykset nousisivat esille. Kolme yritystä valittiin syvällisempään tarkasteluun. Yritysten tuotteita, taloudellista asemaa ja globaalia verkostoa vertailtiin keskenään muiden tekijöiden, kuten maailmantalouden ohessa. Taloudellisesti vakaa ja teknisesti monipuolinen yritys kohtasi yritysoston motiivit parhaiten. Kohteen positiivisia puolia olivat sijainti, tuotteet ja palvelut. Lisäksi, yritys sopii ostajan strategiaan sekä auttaa kohtaamaan asiakkaiden nykyiset ja tulevat tarpeet.