Preisach modeling of hysteresis for a pseudoelastic Cu-Zn-Al single crystal

Stress-strain trajectories associated with pseudoelastic behavior of a Cu¿19.4 Zn¿13.1 Al (at.%) single crystal at room temperature have been determined experimentally. For a constant cross-head speed the trajectories and the associated hysteresis behavior are perfectly reproducible; the trajectories exhibit memory properties, dependent only on the values of return points, where transformation direction is reverted. An adapted version of the Preisach model for hysteresis has been implemented to predict the observed trajectories, using a set of experimental first¿order reversal curves as input data. Explicit formulas have been derived giving all trajectories in terms of this data set, with no adjustable parameters. Comparison between experimental and calculated trajectories shows a much better agreement for descending than for ascending paths, an indication of a dissymmetry between the dissipation mechanisms operative in forward and reverse directions of martensitic transformation.

Optical correlation by use of partial phase-only modulation with VGA liquid-crystal displays

The development of liquid-crystal panels for use in commercial equipment has been aimed at improving the pixel resolution and the display efficiency. These improvements have led to a reduction in the thickness of such devices, among other outcomes, that involves a loss in phase modulation. We propose a modification of the classical phase-only filter to permit displays in VGA liquid-crystal panels with a constant amplitude modulation and less than a 2¿(PI) phase modulation. The method was tested experimentally in an optical setup.

Crystal defects and spin tunneling in single crystals of Mn12 clusters

The question addressed in this paper is that of the influence of the density of dislocations on the spin tunneling in Mn12 clusters. We have determined the variation in the mosaicity of fresh and thermally treated single crystals of Mn12 by analyzing the widening of low angle x-ray diffraction peaks. It has also been well established from both isothermal magnetization and relaxation experiments that there is a broad distribution of tunneling rates which is shifted to higher rates when the density of dislocations increases.

Animal manure phosphorus characterization by sequential chemical fractionation, release kinetics and 31P-NMR analysis

Phosphate release kinetics from manures are of global interest because sustainable plant nutrition with phosphate will be a major concern in the future. Although information on the bioavailability and chemical composition of P present in manure used as fertilizer are important to understand its dynamics in the soil, such studies are still scarce. Therefore, P extraction was evaluated in this study by sequential chemical fractionation, desorption with anion-cation exchange resin and 31P nuclear magnetic resonance (31P-NMR) spectroscopy to assess the P forms in three different dry manure types (i.e. poultry, cattle and swine manure). All three methods showed that the P forms in poultry, cattle and swine dry manures are mostly inorganic and highly bioavailable. The estimated P pools showed that organic and recalcitrant P forms were negligible and highly dependent on the Ca:P ratio in manures. The results obtained here showed that the extraction of P with these three different methods allows a better understanding and complete characterization of the P pools present in the manures.

Metastable liquid-liquid phase transition in a single-component system with only one crystal phase and no density anomaly

We investigate the phase behavior of a single-component system in three dimensions with spherically-symmetric, pairwise-additive, soft-core interactions with an attractive well at a long distance, a repulsive soft-core shoulder at an intermediate distance, and a hard-core repulsion at a short distance, similar to potentials used to describe liquid systems such as colloids, protein solutions, or liquid metals. We showed [Nature (London) 409, 692 (2001)] that, even with no evidence of the density anomaly, the phase diagram has two first-order fluid-fluid phase transitions, one ending in a gas¿low-density-liquid (LDL) critical point, and the other in a gas¿high-density-liquid (HDL) critical point, with a LDL-HDL phase transition at low temperatures. Here we use integral equation calculations to explore the three-parameter space of the soft-core potential and perform molecular dynamics simulations in the interesting region of parameters. For the equilibrium phase diagram, we analyze the structure of the crystal phase and find that, within the considered range of densities, the structure is independent of the density. Then, we analyze in detail the fluid metastable phases and, by explicit thermodynamic calculation in the supercooled phase, we show the absence of the density anomaly. We suggest that this absence is related to the presence of only one stable crystal structure.

Pilot Knob State Park, Merrick State Park, Eagle Lake State Park, Rice Lake State Park and Crystal, East and West Twin, and Duck Lakes,1925.

Provides information on Pilot Knob State Park, Merrick State Park, Eagle Lake State Park, Rice Lake State Park and Crystal, East and West Twin, and Duck Lakes including history, maps, location, terrain, photos, vegetation and wildlife.

Magnetic properties and domain-wall motion in single-crystal BaFe10.2Sn0.74Co0.66O19

The magnetic properties of BaFe12O19 and BaFe10.2Sn0.74Co0.66O19 single crystals have been investigated in the temperature range (1.8 to 320 K) with a varying field from -5 to +5 T applied parallel and perpendicular to the c axis. Low-temperature magnetic relaxation, which is ascribed to the domain-wall motion, was performed between 1.8 and 15 K. The relaxation of magnetization exhibits a linear dependence on logarithmic time. The magnetic viscosity extracted from the relaxation data, decreases linearly as temperature goes down, which may correspond to the thermal depinning of domain walls. Below 2.5 K, the viscosity begins to deviate from the linear dependence on temperature, tending to be temperature independent. The near temperature independence of viscosity suggests the existence of quantum tunneling of antiferromagnetic domain wall in this temperature range.

The roles of flux- and decompression melting and their respective fractionation lines for continental crust formation: Evidence from the Kohistan arc

Delamination and foundering of the lower continental crust (LCC) into the mantle is part of the crust-forming mechanism. However, knowledge of the composition and mineralogy of the preserved or delaminated LCC over geological timescales remains scarce. We provide a synopsis of recent research within the Kohistan arc (Pakistan) and demonstrate that hydrous and less hydrous liquid lines of descent related to flux assisted and decompression mantle melting, respectively, produce compositionally different lower crustal rocks. The argument refers to two lower crustal sections exposed in Kohistan, the older Southern Plutonic Complex (SPC) and the younger Chilas Complex. The SPC typifies a hydrous, high-pressure fractionation sequence of olivine-pyroxenes-garnet-Fe/Ti-oxide-amphibole-plagioclase. The Chilas Complex illustrates a less hydrous fractionation sequence of olivine-clinopyroxene-orthopyroxene-plagioclase-amphibole. Despite the similarity of the Chilas Complex rocks to proposed lower crust compositions, the less hydrous fractionation results in unrealistically small volumes of silica-rich rocks, precluding the Chilas Complex gabbros to represent the magmatic complement to the upper crust. The composition of the SPC lower crust differs markedly from bulk lower crust estimates, but is complementary to silica-rich rocks exposed along this section and in the Kohistan batholith. These observations inspire a composite model for the formation of continental crust (CC) where the negatively buoyant delaminated and the buoyant preserved lower continental crusts (LCC) differ in genesis, mineralogy, and composition. We propose that the upper, non-sedimentary subsequent removal of the complementary, negatively buoyant garnet-pyroxene-amphibole-plagioclase-rich cumulates. In contrast, the LCC, which is buoyant and preserved over geological timescales, is formed by less hydrous parental mantle melts. We suggest that the bulk continental crust composition is related to mixing of these petrologically not directly related end members. Published by Elsevier B.V.

Post-Plutonic Magmatism: from the Source to the Emplacement of an Upper Crustal Dyke Swarm, Adamello Massif, Italy

Magmas of the arc-tholeiitic and calc-alkaline differentiation suites contribute substantially to the formation of continental crust in subduction zones. Different geochemical-petrological models have been put forward to achieve evolved magmas forming large volumes of tonalitic to granitic plutons, building an important part of the continental crust. Primary magmas produced in the mantle wedge overlying the subducted slab migrate through the mantle and the crust. During the transfer, magma can accumulate in intermediate reservoirs at different levels where crystallization leads to differentiation and the heat transfer from the magma, together with gained heat from solidification, lead to partial melting of the crust. Partial melts can be assimilated and mix with more primitive magma. Moreover, already formed crystal cumulates or crystal mushes can be recycled and reactivated to transfer to higher crustal levels. Magma transport in the crust involves fow through fractures within a brittle elastic rock. The solidified magma filled crack, a dyke, can crosscut previously formed geological structures and thus serves as a relative or absolute time marker. The study area is situated in the Adamello massif. The Adamello massif is a composite of plutons that were emplaced between 42 and 29 million years. A later dyke swarm intruded into the southern part of the Adamello Batholith. A fractionation model covering dyke compositions from picrobasalts to dacites results in the cummulative crystallization of 17% olivine, 2% Cr-rich spinel, 18% clinopyroxene, 41% amphibole, 4% plagioclase and 0.1% magnetite to achieve an andesitic composition out of a hydrous primitive picrobasalt. These rocks show a similar geochemical evolution as experimental data simulating fractional crystallization and associated magma differentiation at lower crustal depth (7-10 kbar). The peraluminous, corundum normative composition is one characteristic of more evolved dacitic magmas, which has been explained in a long lasting debate with two di_erent models. Melting of mafic crust or politic material provides one model, whereas an alternative is fractionation from primary mantle derived melts. Amphibole occurring in basaltic-andesitic and andesitic dyke rocks as fractionating cumulate phase extracted from lower crustal depth (6-7.5 kbar) is driving the magmas to peraluminous, corundum normative compositions, which are represented by tonalites forming most of the Adamello Batholith. Most primitive picrobasaltic dykes have a slightly steepened chondrite normalized rare earth elements (REE) pattern and the increased enrichment of light-REE (LREE) for andesites and dacites can be explained by the fractional crystallization model originating from a picrobasalt, taking the changing fractionating phase assemblage and temperature into account. The injection of hot basaltic magma (~1050°C) in a closely spaced dyke swarm increases the surface of the contact to the mainly tonalitic wallrock. Such a setting induces partial melting of the wall rock and selective assimilation. Partial melting of the tonalite host is further expressed through intrusion breccias from basaltic dykes. Heat conduction models with instantaneous magma injection for such a dyke swarm geometry can explain features of partial melting observed in the field. Geochemical data of minerals and bulk rock further underline the selective or bulk assimilation of the tonalite host rock at upper crustal levels (~2-3 kbar), in particular with regard to light ion lithophile elements (LILE) such as Sr, Ba and Rb. Primitive picrobasalts carry an immiscible felsic assimilant as enclaves that bring along refractory rutile and zircon with textures typically found in oceanic plagiogranites or high pressure/low-temperature metamorphic rocks in general. U-Pb data implies a lower Cretaceous age for zircon not yet described as assimilant in Eocene to Oligocene magmatic rocks of the Central Southern Alps. The distribution of post-plutonic dykes in large batholiths such as the Adamello is one of the key features for understanding the regional stress field during the post-batholith emplacement cooling history. The emplacement of the regional dyke swarm covering the southern part of the Adamello massif was associated with consistent left lateral strike-slip movement along magma dilatation planes, leading to en echelon segmentation of dykes. Through the dilation by magma of pre-existing weaknesses and cracks in an otherwise uniform host rock, the dyke propagation and according orientation in the horizontal plane adjusted continuously perpendicular to least compressive remote stress σ3, resulting in an inferred rotation of the remote principal stress field. Les magmas issus des zones de subduction contribuent substantiellement à la formation de la croûte continentale. Les plutons tonalitiques et granitiques représentent, en effet, une partie importante de la croûte continentale. Des magmas primaires produits dans le 'mantle wedge ', partie du manteau se trouvant au-dessus de la plaque plongeante dans des zones de subduction, migrent à travers le manteau puis la croûte. Pendant ce transfert, le magma peut s'accumuler dans des réservoirs intermédiaires à différentes profondeurs. Le stockage de magma dans ces réservoirs engendre, d'une part, la différentiation des magmas par cristallisation fractionnée et, d'autre part, une fusion partielle la croûte continentale préexistante associée au transfert de la chaleur des magmas vers l'encaissant. Ces liquides magmatiques issus de la croûte peuvent, ensuite, se mélanger avec des magmas primaires. Le transport du magma dans la croûte implique notamment un flux de magma à travers différentes fractures recoupant les roches encaissantes élastiques. Au cours de ce processus de migration, des cumulats de cristaux ou des agrégats de cristaux encore non-solidifiés, peuvent être recyclés et réactivés pour être transportés à des niveaux supérieures de la croûte. Le terrain d'étude est situé dans le massif d'Adamello. Celui-ci est composé de plusieurs plutons mis en place entre 42 et 29 millions d'années. Dans une phase tardive de l'activité magmatique liée à ce batholite, une série de filons de composition variable allant de picrobasalte à des compositions dacitiques s'est mise en place la partie sud du massif. Deux modèles sont proposés dans la littérature, pour expliquer la formation des magmas dacitiques caractérisés par des compositions peralumineux (i.e. à corindon normatif). Le premier modèle propose que ces magmas soient issus de la fusion de matériel mafique et pélitique présent dans la partie inférieur de la croûte, alors que le deuxième modèle suggère une évolution par cristallisation fractionnée à partir de liquides primaires issus du manteau. Un modèle de cristallisation fractionnée a pu être développé pour expliquer l'évolution des filons de l'Adamello. Ce modèle explique la formation des filons dacitiques par la cristallisation fractionnée de 17% olivine, 2% spinelle riche en Cr, 18% clinopyroxène, 41% amphibole, 4% plagioclase et 0.1% magnetite à partir de liquide de compositions picrobasaltiques. Ce modèle prend en considération les contraintes pétrologiques déduites de l'observation des différents filons ainsi que du champ de stabilité des différentes phases en fonction de la température. Ces roches montrent une évolution géochimique similaire aux données expérimentales simulant la cristallisation fractionnée de magmas évoluant à des niveaux inférieurs de la croûte (7-10 kbar). Le modèle montre, en particulier, le rôle prépondérant de l'amphibole, une phase qui contrôle en particulier le caractère peralumineux des magmas différentiés ainsi que leurs compositions en éléments en traces. Des phénomènes de fusion partielle de l'encaissant tonalitique lors de la mise en place de _lons mafiques sont observée sur le terrain. L'injection du magma basaltique chaud (~1050°C) sous forme de filons rapprochés augmente la surface du contact avec l'encaissante tonalitique. Une telle situation produit la fusion partielle des roches encaissantes nécessaire à l'incorporation d'enclaves mafiques observés au sein des tonalites. Pour comprendre les conditions nécessaires pour la fusion partielle des roches encaissantes, des modèles de conduction thermique pour une injection simultanée d'une série de filons ont été développées. Des données géochimiques sur les minéraux et sur les roches totales soulignent qu'au niveau supérieur de la croûte, l'assimilation sélective ou totale de l'encaissante tonalitique modifie la composition du liquide primaire pour les éléments lithophiles tel que le Sr, Ba et Rb. Un autre aspect important concernant la pétrologie des filons de l'Adamello est la présence d'enclaves felsiques dans les filons les plus primitifs. Ces enclaves montrent, en particulier, des textures proches de celles rencontrées dans des plagiogranites océaniques ou dans des roches métamorphiques de haute pression/basse température. Ces enclaves contiennent du zircon et du rutile. La datations de ces zircons à l'aide du géochronomètre U-Pb indique un âge Crétacé inférieur. Cet âge est important, car aucune roche de cet âge n'a été considérée comme un assimilant potentiel pour des roches magmatiques d'âge Eocène à Oligocène dans les Alpes Sud Centrales. La réparation spatiale des filons post-plutoniques dans des grands batholites tel que l'Adamello, est une caractéristique clé pour la compréhension des champs de contraintes lors du refroidissement du batholite. L'orientation des filons va, en particulier, indiqué la contrainte minimal au sein des roches encaissante. La mise en place de la série de filon recoupant la partie Sud du massif de l'Adamello est associée à un décrochement senestre, un décrochement que l'on peut lié aux contraintes tectoniques régionales auxquelles s'ajoutent l'effet de la dilatation produite par la mise en place du batholite lui-même. Ce décrochement senestre produit une segmentation en échelon des filons.

Myeloid-related proteins 8 and 14 contribute to monosodium urate monohydrate crystal-induced inflammation in gout.

OBJECTIVE: Monosodium urate monohydrate (MSU) crystal-induced interleukin-1β (IL-1β) secretion is a critical factor in the pathogenesis of gout. However, without costimulation by a proIL-1β-inducing factor, MSU crystals alone are insufficient to induce IL-1β secretion. The responsible costimulatory factors that act as a priming endogenous signal in vivo are not yet known. We undertook this study to analyze the costimulatory properties of myeloid-related protein 8 (MRP-8) and MRP-14 (endogenous Toll-like receptor 4 [TLR-4] agonists) in MSU crystal-induced IL-1β secretion and their relevance in gout. METHODS: MRP-8/MRP-14 was measured in paired serum and synovial fluid samples by enzyme-linked immunosorbent assay (ELISA) and localized in synovial tissue from gout patients by immunohistochemistry. Serum levels were correlated with disease activity, and MSU crystal-induced release of MRPs from human phagocytes was measured. Costimulatory effects of MRP-8 and MRP-14 on MSU crystal-induced IL-1β secretion from phagocytes were analyzed in vitro by ELISA, Western blotting, and polymerase chain reaction. The impact of MRP was tested in vivo in a murine MSU crystal-induced peritonitis model. RESULTS: MRP-8/MRP-14 levels were elevated in the synovium, tophi, and serum of patients with gout and correlated with disease activity. MRP-8/MRP-14 was released by MSU crystal-activated phagocytes and increased MSU crystal-induced IL-1β secretion in a TLR-4-dependent manner. Targeted deletion of MRP-14 in mice led to a moderately reduced response of MSU crystal-induced inflammation in vivo. CONCLUSION: MRP-8 and MRP-14, which are highly expressed in gout, are enhancers of MSU crystal-induced IL-1β secretion in vitro and in vivo. These endogenous TLR-4 ligands released by activated phagocytes contribute to the maintenance of inflammation in gout.

Elemental and isotopic zoning in natural alpine quartz

THESIS ABSTRACT : Stable isotope geochemistry is used to help resolve a large number of geological questions. In order to do this, it is essential to understand the different mechanisms that govern isotopic fractionation processes between different phases and to identify the conditions required to reach equilibrium fractionation. However, at low temperatures, these processes are poorly constrained and many factors can induce differential partitioning of the isotopes between sectors of a mineral species and the fluid during mineral growth. This can result in so-called 'sector zoning' of a mineral species. The aim of this thesis is to evaluate the occurrence of sector zoning of the oxygen isotopes and trace elements in natural α-quartz crystals and to identify the reasons for such zoning. The implications for the fluid-mineral interactions are studied in the context of the Alpine metamorphism. The approach chosen has focused on examining the crystal structure, cathodoluminescence appearance (CL), and on relating elemental (e.g. Li, Na, Al, P, K, Ca, Ge, Ti, Fe) to stable oxygen isotope compositions between and along different growth sectors. Low temperature quartz samples were selected from Alpine veins in different localities, where growth conditions have already been well constrained. The mineralogy as well as the isotopic compositions of the host rocks were also investigated, in order to interpret the variations obtained between the different growth stages in the framework of fluid-rock interaction during Alpine metamorphism. Depending on the growth conditions, most of the studied quartz is strongly zoned in CL, and it reveals corresponding zonations in the trace element content (e.g. growth zoning). Aluminium, substituting for Si in the lattice, was found in concentrations up to 1000's ppma, and its distribution is strongly related to Li and H and to a lesser extent, to Ge. Elemental sector zoning is evident from the distribution of these three elements since they exhibit differences in their respective concentrations between faces for distinct growth zones, with prismatic faces having the lowest Al contents. Quartz from veins in magmatic rocks, for example, tend to have lower Al concentrations and similar concentrations of Li and Ti suggesting also a contribution of these elements from the host rock. The relationship between Al and Li is still correlated. Only Alpine crystals grown at higher temperatures (~400°C) without any CL zoning feature are free of these impurities and do not show such zoning characteristics. Differences in the δ18O values were measured between different faces principally in the AIenriched growth zones or stages. These results were confirmed by the means of two different methods (in situ/non in situ). However, it was determined that the Al concentrations do not affect significantly oxygen isotope fractionations at 300°C. The results altogether suggest that the presence of sector zoning in quartz crystals is real, but not universal, and henceforth should be taken into consideration for any use of these systems. The occurrence of disequilibrium partitioning has been enhanced and is possibly related to kinetic processes as well as structural effects that do not affect similarly trace element incorporation and isotopic fractionation. In situ measurements also revealed fine scale δ18O zonations along growth paths that are useful to constrain fluid-rock interactions during Alpine metamorphism. Variations in the δ18O values present along growth vectors indicate changes in the fluid composition and origin. Association with oxygen isotope composition of the host rock allows for the deduction of interactions between rocks, veins and consequently fluids, as well as fluid regimes. RESUME DE LA THESE : A basses températures, (i.e. <400°C) les différents mécanismes qui régissent le fractionnement isotopique ainsi que les conditions nécessaires pour établir un état d'équilibre sont peu connus et nombre de paramètres peuvent entraîner un partitionnement chimique différentiel entre différents secteurs d'un minéral et le fluide en contact. Ainsi, ce travail de thèse a pour but d'évaluer la possible présence de zonages sectoriels en isotopes de l'oxygène mais aussi en éléments traces dans des cristaux naturels de quartz-α de basses températures, ainsi que les raisons d'un tel phénomène et enfin ses implications sur les interactions fluide-roche, principalement dans le cadre du métamorphisme Alpin. La structure et l'apparence en cathodoluminescence (CL) des échantillons ont été caractérisées avant de retracer en détail les compositions en élément traces (Li, Na, Al, P, K, Ca, Ge, Ti, Fe) et en isotopes de l'oxygène, le long et entre différents secteurs. Les échantillons de quartz sélectionnés proviennent majoritairement de veines Alpine de différentes localités, où les conditions de croissance ont été déjà bien caractérisées. Les compositions minéralogiques et isotopiques de la roche encaissante ont aussi été examinées, pour contraindre les variations obtenues dans un contexte Alpin. Selon leurs conditions de croissance, la plupart des cristaux étudiés sont fortement zonés, ce qui est souligné par un zonage des concentrations en éléments traces (e.g. zonage de croissance). L'Aluminium, qui peut se substituer à la Silice dans le réseau cristallin, a été retrouvé jusqu'en très grandes concentrations dans certaines zones (plusieurs milliers de ppma). De plus, la distribution en Al est fortement liée à celles de Li et H, ainsi que dans une moindre mesure à Ge. La présence de zonage sectoriel est évidente au niveau de ces éléments qui montrent de larges différences de concentrations entre différentes faces pour une même zone de croissance, avec les concentrations les plus basses retrouvées dans les faces prismatiques. Les quartz de veines situées dans des roches magmatiques par exemple possèdent des concentrations en Li et Ti de même ordre de grandeur, confirmant le rôle de la composition de la roche encaissante. La relation Li/Al est toujours fortement présente, mais ce rapport est fonction de la face mesurée. Seuls les cristaux Alpins de plus hautes températures (400°C) ne possédant pas de zones en CL ne présentent aucune de ces caractéristiques. Des différences dans les valeurs de δ18O de zones identiques enrichies en Al ont clairement été mesurées entre les différentes faces r, z, et m, mais aussi au sein d'une même seule zone, indiquant que le fractionnement a probablement eu lieu en déséquilibre. Il a été déterminé que la présence d'Al dans ces teneurs n'avait qu'un faible effet sur le fractionnement isotopique de l'oxygène. L'utilisation de deux méthodes différentes a permis d'obtenir des résultats in situ et non in situ concordants. La comparaison des résultats obtenus permet de démontrer que le zonage sectoriel est bien présent dans certains cristaux de quartz, et dépend des conditions de formation. La présence d'un partitionnement différentiel des éléments traces peut être due à des effets cinétiques aussi bien que structuraux, alors que le zonage sectoriel des isotopes de l'oxygène aurait d'autres origines. Il est alors évident que la possibilité de zonage sectoriel doit être désormais pris en considération avant toute interprétations de données isotopiques de cristaux zonés. Les mesures in situ ont de plus permis de distinguer de fines variations des valeurs δ18O au cours de la croissance, qui peuvent aider à retracer la circulations des fluides dans les Alpes durant cette période. En association avec les compositions des roches encaissantes, ii est possible de déduire les interactions entre roches, veines, et par conséquent fluides, au cours de différentes étapes. RESUME GRAND PUBLIC : La géochimie des isotopes stables a pris beaucoup d'importance depuis ces dernières années pour aider à résoudre nombre de questions géologiques, en se basant sur les caractéristiques du fractionnement isotopiques pour différents systèmes. Il est donc nécessaire d'avoir une connaissance approfondie des mécanismes qui s'appliquent au fractionnement isotopique entre les minéraux et les fluides à partir desquels ils se forment. Ces mécanismes ont été bien approchés par différents types de calibrations pour des systèmes à hautes températures, cependant cela n'est pas aussi évident pour les systèmes à des températures inférieures à 400-500°C. Ce travail de thèse a pour but d'aider à la description et la compréhension des phénomènes qui peuvent affecter le fractionnement isotopique à basses températures, ainsi que leurs implications, à partir de l'étude de cristaux de quartz. Le choix des échantillons s'est porté sur des cristaux naturels formés à des températures inférieures ou égales à 400°C, provenant majoritairement de fissures hydrothermales Alpines dont les conditions de formation ont déjà été déterminées. L'étude des cristaux Alpin permet de plus de replacer les résultats obtenus dans le contexte du métamorphisme Alpin au cours du Miocène (21-13 Ma). Après examen de la structure et de la morphologie des cristaux, et leur caractérisation par cathodoluminescence (CL), des analyses chimiques détaillées sur les éléments en traces pouvant entrer dans le réseau cristallin du quartz comme impuretés (i.e. Li, Na, Al, P, K, Ca, Ge, Ti), et des isotopes stables de l'oxygène, ont été menées. En fonction des conditions de croissance, la plupart des cristaux présentent des zonations, qui peuvent être facilement reliées à la distribution des éléments traces analysés par microsonde électronique, sonde ionique (SIMS) et LA-ICPMS. De fortes concentrations d'Aluminium (plusieurs milliers de parties par million atomique) ont pu être observées dans les zones les plus externes des cristaux. De plus, les concentrations en Al et en Li sont toujours corrélées; la présence d'Hydrogène déduite à partir d'analyses par FTIR suit cette même tendance. Les différentes faces des cristaux présentent des concentrations distinctes d'Al, Li et H pour des mêmes zones de croissance, avec par exemple les concentrations les plus faibles dans les zones des faces prismatiques. Cela implique la présence d'un zonage sectoriel, qui a déjà été observé principalement dans des carbonates mais jamais décrit auparavant pour des quartz. Seuls les cristaux alpins homogènes en CL dont la croissance s'est faite à plus haute température (400°C) ne présentent aucune de ces caractéristiques. Par analogie avec le zonage sectoriel en Al, élément qui se substitue au Si dans le réseau cristallin du quartz, il est possible de penser qu'un zonage sectoriel pourrait aussi s'appliquer aux isotopes de l'oxygène. Des précédentes études avaient en effet émis cette hypothèse. Nos résultats ont été obtenus à partir d'analyses à la fois in- situ par SIMS, et par extraction assistée par laser-CO2 sur des parties de quartz soigneusement séparées, et sont en accord entre les deux méthodes. Un zonage sectoriel est en effet bien présent pour les cristaux alpins, mais principalement au niveau des zones très riches en Aluminium. Cependant, il a été déterminé que la présence d'Al dans ces teneurs avait un effet plus que minimal sur le fractionnement isotopique de l'oxygène. Des différences importantes ont été observées entre les faces r & z mais aussi au sein d'une même et seule zone, indiquant que le fractionnement a pu avoir lieu en déséquilibre, ce qui est aussi visible au niveau des valeurs totalement opposées entre faces pour la dernière phase de croissance de certains cristaux. Ainsi l'association de ces résultats laisse suggérer que la présence d'un zonage sectoriel peut être liée à différents paramètres tels que le taux de croissance ou la structure de surface du cristal, mais qui n'affectent pas de la même façon l'incorporation des éléments traces et le fractionnement isotopique. La possibilité d'un zonage sectoriel est importante à prendre en compte lors de toute interprétation de données isotopiques. Les analyses des isotopes de l'oxygène effectuées par SIMS ont aussi permis de distinguer des variations importantes à petite échelle au cours de la croissance. Des mesures faites par laser CO2 sur certaines roches encaissantes, ont permis distinguer plusieurs étapes dans la croissance des minéraux et de déduire le rôle de l'encaissant et le type de fluide. En association avec de précédentes études, il a été ainsi possible de mieux contraindre la formation de ces cristaux dans le contexte alpin et la circulation de fluide au cours du métamorphisme alpin durant le Miocène.

Reduction of Concrete Deterioration by Ettringite Using Crystal Growth Inhibition Techniques, TR-431, 2001

Many researchers have concluded that secondary or delayed ettringite is responsible for serious premature deterioration of concrete highways. In some poorly performing Iowa concretes, ettringite is the most common secondary mineral but its role in premature deterioration is uncertain since some researchers still maintain that secondary ettringite does not itself cause deterioration. The current research project was designed to determine experimentally if it is possible to reduce secondary ettringite formation in concrete by treating the concrete with commercial crystallization inhibitor chemicals. The hypothesis is such that if the amount of ettringite is reduced, there will also be a concomitant reduction of concrete expansion and cracking. If both ettringite formation and deterioration are simultaneously reduced, then the case for ettringite induced expansion/cracking is strengthened. The experiment used four commercial inhibitors - two phosphonates, a polyacrylic acid, and a phosphate ester. Concrete blocks were subjected to continuous immersion, wet/dry and freeze/thaw cycling in sodium sulfate solutions and in sulfate solutions containing an inhibitor. The two phosphonate inhibitors, Dequest 2060 and Dequest 2010, manufactured by Monsanto Co., were effective in reducing ettringite nucleation and growth in concrete. Two other inhibitors, Good-rite K752 and Wayhib S were somewhat effective, but less so than the two phosphonates. Rapid experiments with solution growth inhibition of ettringite without the presence of concrete phases were used to explore the mechanisms of inhibition of this mineral. Reduction of new ettringite formation in concrete blocks also reduced expansion and cracking of the blocks. This relationship clearly links concrete expansion with this mineral - a conclusion that some research workers have disputed despite theoretical arguments for such a relationship and despite numerous observations of ettringite mineralization in prematurely deteriorated concrete highways. Secondary ettringite nucleation and growth must cause concrete expansion because the only known effect of the inhibitor chemicals is to reduce crystal nucleation and growth, and the inhibitors cannot in any other way be responsible for the reduction in expansion. The mechanism of operation of the inhibitors on ettringite reduction is not entirely clear but the solution growth experiments show that they prevent crystallization of a soluble ettringite precursor gel. The present study shows that ettringite growth alone is not responsible for expansion cracking because the experiments showed that most expansion occurs under wet/dry cycling, less under freeze/thaw cycling, and least under continuous soaking conditions. It was concluded from the different amounts of damage that water absorption by newly-formed, minute ettringite crystals is responsible for part of the observed expansion under wet/dry conditions, and that reduction of freeze resistance by ettringite filling of air-entrainment voids is also important in freeze/thaw environments.

The carbon isotope composition of natural SiC (moissanite) from the Earth's mantle: New discoveries from ophiolites

Moissanite (natural SiC) has been recovered from podiform chromitites of several ophiolite complexes, including the Luobusa and Donqiao ophiolites in Tibet, the Semail ophiolite in Oman and the United Arab Emirates, and the Ray-Iz ophiolite of the Polar Urals, Russia. Taking these new occurrences with the numerous earlier reports of moissanite in diamondiferous kimberlites leads to the conclusion that natural SiC is a widespread mineral in the Earth's mantle, which implies at least locally extremely low redox conditions. The ophiolite moissanite grains are mostly fragments (20 to 150 mu m) with one or more crystal faces, but some euhedral hexagonal grains have also been recovered. Twinned crystals are common in chromitites from the Luobusa ophiolite. The moissanite is rarely colorless, more commonly light bluish-gray to blue or green. Many grains contain inclusions of native Si and Fe-Si alloys (FeSi(2), Fe(3)Si(7)). Secondary ion mass spectrometric (SIMS) analysis shows that the ophiolite-hosted moissanite has a distinctive (13)C-depleted isotopic composition (delta(13)C from -18 to -35 parts per thousand, n=36), much lighter than the main carbon reservoir in the upper mantle (delta(13)C near -5 parts per thousand). The compiled data from moissanite from kimberlites and other mantle settings share the characteristic of strongly (13)C-depleted isotopic composition. This suggests that moissanite originates from a separate carbon reservoir in the mantle or that its formation involved strong isotopic fractionation. The degree of fractionation needed to produce the observed moissanite compositions from the main C-reservoir would be unrealistically large at the high temperatures required for moissanite formation. Subduction of biogenic carbonaceous material could potentially satisfy both the unusual isotopic and redox constraints on moissanite formation, but this material would need to stay chemically isolated from the upper mantle until it reached the high-T stability field of moissanite. The origin of moissanite in the mantle is still unsolved, but all evidence from the upper mantle indicates that it cannot have formed there, barring special and local redox conditions. We suggest, alternatively, that moissanite may have formed in the lower mantle, where the existence of (13)C-depleted carbon is strongly supported by studies of extraterrestrial carbon (Mars, Moon, meteorites). (C) 2009 Elsevier B. V. All rights reserved.

Stable O and H isotopic composition of hydrous minerals as proxies for paleoclimate and -topography : application to the European Alps

The isotopie composition of clay minerals can be used to gain information on paleoaltitude, -topography and -climate during the time of their formation, as they form in isotopie equilibrium with ambient water, which has an isotopie composition that is determined by previous rain-out. In this thesis, the usability of this approach is evaluated for sample material from both the North Alpine Foreland Basin and internal parts of the European Alps. The isotopie composition of precipitation is determined by the air temperature and the extent of previous rain-out, which in turn is affected by the distance to the point of origin of the water vapor and the condensation conditions. An orographic barrier leads to uplift and adiabatic cooling of air masses and thereby enhances rainfall with a characteristic depletion in heavy 0 and H isotopes. Processes such as evaporation and mixing of water with different origin affect the isotopie composition further on the surface. Clay minerals are hydrous phyllosilicates that can form during weathering or pedogenesis in isotopie equilibrium with the present water and inherit its isotopie composition with a characteristic fractionation. If their isotopie composition was preserved after formation and the necessary parameters are known, it is possible to calculate the isotopie composition of the ambient water and thereby reconstruct climatic and topographic conditions during their formation. Due to the hygroscopic behavior of the sample material, analytical procedures needed to be modified to allow an analysis of the oxygen and hydrogen isotopie composition of the hydroxyl water built into their crystal structure and not the one of recently adsorbed water. In order to determine typical 5lsO and 8D values of meteoric water and minerals in the weathering environment in high Alpine regions, samples of surface water and soils from the valley of Visp in the Swiss Alps were studied that were collected along a transect with varying altitudes and host rock lithologies. The actual aim to attempt the reconstruction of Alpine paleoelevations was addressed by the analysis of sediments deposited under marine and terrestrial conditions during the Miocene and Oligocene, which were sampled from different locations in Switzerland, Germany and Austria. Further bentonite and fault gouge clay samples were used as reference material from low and high elevations. Results show that the isotopie composition of clay minerals can be influenced by several factors, such as the mode and site of their formation, possible isotope exchange (which is evident for 8D values), the samples' mineral composition (such as the presence of detrital material) and the deposition environment. With a consideration of these parameters and limitation to certain sample material, conclusions are drawn on the isotopie composition of the water from which the clay minerals formed. Most of the obtained values lie in the same range as has been reported in literature for foreland precipitation. The reconstruction of paleoelevation might be possible for selected sites with a geographical setting close to the Alpine chain or for intramontane basins. - La composition isotopique des argiles, qui se forment typiquement en contact avec des eaux superficielles, peut être utilisée pour obtenir des informations sur la paléoaltitude, la paléotopographie et le paléoclimat pendant leur création. La composition en isotopes stable (oxygène et hydrogène) des eaux de pluie est déterminée par l'altitude, la température, la distance depuis le lieu d'évaporation et par le taux de précipitation. Certains processus comme l'évaporation, l'interaction avec des minéraux et le mélange d'eaux d'origines variées peuvent aussi changer la composition des eaux de surface. Les argiles sont des pliyllosilicates hydratés qui sont crées par l'altération des roches au contact de ces eaux de surface et ils acquièrent une composition isotopique qui est soumise à un certain fractionnement. L'objectif de cette thèse est d'évaluer si l'effet de l'altitude des Alpes, est détectable dans la composition isotopique des sédiments du bassin d'avant-pavs pendant le Miocène. Après avoir établi la procédure analytique, des compositions isotopiques typiques de régions de hautes altitudes ont été determine sur les eaux de surfaces (rivières) et sur des échantillons de sols, le long d'une coupe dans la valée de Visp, dans les Alpes Suisses. Une reconstruction des paléoaltitudes Miocènes Alpines a ensuite été mené par l'analyse de sédiments marins et terrestres en utilisant des échantillons d'âges variés et provenant de Suisse, d'Allemagne et d'Autriche. Les résultats montrent que la composition isotopique des échantillons est impactée par de multiples facteurs, tels que le mode de et le lieu de formation. un possible échange isotopique tardif (surtout pour 5D). leur composition minéralogique et l'environnement de leur sédimentation. Après un examen prudent de ces paramètres, et en se limitant à un certain assortiment d'échatillons, on peut tirer des conclusions sur la composition isotopique des eaux originelles pour en déduire l'effet du climat et de la topographie.