The financial sustainability of passive house construction in Ireland.

In Ireland the average energy cost for a household in 2006 was estimated to be €1,767, an increase of 4% on 2005 figures. With the state o f the current economic climate, home owners are beginning to realise the potential of energy efficient construction methods. The Passive House Standard offers a cost efficient and sustainable construction solution compared to the Traditional Irish construction methods. This report focuses on the Cost comparison between Passive House construction and traditional construction methods. The report also focuses on barriers that are slowing market penetration of the Passive House standard in the Irish Market. It also identifies potential energy savings that passive house occupants would benefit from. The report also highlights professional opinions on the future development o f the Passive House Standard in Ireland. The conclusions of this report are that the Passive House Standard is a more financially suitable construction solution compared to that o f a traditional dwelling complying with the Irish Building Regulations. The report also concludes that the Passive House Standard won’t be introduced as an Irish Building Regulation in the future but that it will have a big impact on future building regulations. The hypothesis o f this report is supported by data obtained from a literature review, qualitative data analysis and a case study. The report recommends that in order for the Passive House Standard to penetrate further into the Irish construction market, various barriers must be rectified. Local manufactures must start producing suitable components that suit the Passive House specification. The Building Energy Rating system must be altered in order for the Passive House to achieve its potential BER rating.

The importance and accuracy of wind power forecasts

Due to the global crisis o f climate change many countries throughout the world are installing the renewable energy o f wind power into their electricity system. Wind energy causes complications when it is being integrated into the electricity system due its intermittent nature. Additionally winds intennittency can result in penalties being enforced due to the deregulation in the electricity market. Wind power forecasting can play a pivotal role to ease the integration o f wind energy. Wind power forecasts at 24 and 48 hours ahead of time are deemed the most crucial for determining an appropriate balance on the power system. In the electricity market wind power forecasts can also assist market participants in terms o f applying a suitable bidding strategy, unit commitment or have an impact on the value o f the spot price. For these reasons this study investigates the importance o f wind power forecasts for such players as the Transmission System Operators (TSOs) and Independent Power Producers (IPPs). Investigation in this study is also conducted into the impacts that wind power forecasts can have on the electricity market in relation to bidding strategies, spot price and unit commitment by examining various case studies. The results o f these case studies portray a clear and insightful indication o f the significance o f availing from the information available from wind power forecasts. The accuracy o f a particular wind power forecast is also explored. Data from a wind power forecast is examined in the circumstances o f both 24 and 48 hour forecasts. The accuracy o f the wind power forecasts are displayed through a variety o f statistical approaches. The results o f the investigation can assist market participants taking part in the electricity pool and also provides a platform that can be applied to any forecast when attempting to define its accuracy. This study contributes significantly to the knowledge in the area o f wind power forecasts by explaining the importance o f wind power forecasting within the energy sector. It innovativeness and uniqueness lies in determining the accuracy o f a particular wind power forecast that was previously unknown.

Population dynamics of 0-group flounder (Platichthys flesus L.) in Galway Bay, West of Ireland and the value of flounder from shore angling tourism in Ireland

The economic value of flounder from shore angling around Ireland was assessed. Flounder catches from shore angling tournaments around Ireland were related to domestic and overseas shore angling expenditure in order to determine an economic value for the species. Temporal trends in flounder angling catches, and specimen (trophy) flounder reports were also investigated. Flounder was found to be the most caught shore angling species in competitions around Ireland constituting roughly one third of the shore angling competition catch although this did vary by area. The total value of flounder from shore angling tourism was estimated to be of the order of €8.4 million. No significant temporal trends in flounder angling catches and specimen reports were found. Thus there is no evidence from the current study for any decline in flounder stocks. The population dynamics of 0-group flounder during the early benthic stage was investigated at estuarine sites in Galway Bay, west of Ireland. Information was analysed from the March to June sampling period over five years (2002 to 2006). Spatial and temporal variations in settlement and population length structure were analysed between beach and river habitats and sites. Settlement of flounder began from late March to early May of each year, most commonly in April. Peak settlement was usually in April or early May. Settlement was recorded earlier than elsewhere, although most commonly was similar to the southern part of the UK and northern France. Settlement was generally later in tidal rivers than on sandy beaches. Abundance of 0-group flounder in Galway Bay did not exhibit significant inter -annual variability. 0-group flounder were observed in dense aggregations of up to 105 m'2, which were patchy in distribution. Highest densities of 0-group flounder were recorded in limnetic and oligohaline areas as compared with the lower densities in polyhaline and to a lesser extent mesohaline areas. Measurements to of salinity allowed the classification of beaches, and tidal river sections near the mouth, into a salinity based scheme for length comparisons. Beaches were classified as polyhaline,the lower section of rivers as mesohaline, and the middle and upper sections as oligohaline. Over the March to June sampling period 0-group flounder utilised different sections at different length ranges and were significantly larger in more upstream sections. During initial settlement in April, 0-group flounder of 8-10 mm (standard length, SL) were present in abundance on polyhaline sandy beaches. By about 10mm (SL), flounder were present in all polyhaline, mesohaline and (oligohaline) sections. 0-group flounder became absent or in insignificant numbers in polyhaline and mesohaline sections in a matter of weeks after first appearance. From April to June, 0-group flounder of 12-30mm (SL) were found in more upstream locations in the oligohaline sections. About one month (May or June) after initial settlement, 0-group flounder became absent from the oligohaline sections. Concurrently, flounder start to reappear in mesohaline and polyhaline areas at approximately 30mm (SL) in June. The results indicate 0-group flounder in the early benthic stage are associated with low salinity areas, but as they grow, this association diminishes. Results strongly suggest that migration of 0-group flounder between habitats takes place during the early benthic phase.

Flood analysis of the clare river catchment considering traditional factors and climate change

The main objective of this thesis on flooding was to produce a detailed report on flooding with specific reference to the Clare River catchment. Past flooding in the Clare River catchment was assessed with specific reference to the November 2009 flood event. A Geographic Information System was used to produce a graphical representation of the spatial distribution of the November 2009 flood. Flood risk is prominent within the Clare River catchment especially in the region of Claregalway. The recent flooding events of November 2009 produced significant fluvial flooding from the Clare River. This resulted in considerable flood damage to property. There were also hidden costs such as the economic impact of the closing of the N17 until floodwater subsided. Land use and channel conditions are traditional factors that have long been recognised for their effect on flooding processes. These factors were examined in the context of the Clare River catchment to determine if they had any significant effect on flood flows. Climate change has become recognised as a factor that may produce more significant and frequent flood events in the future. Many experts feel that climate change will result in an increase in the intensity and duration of rainfall in western Ireland. This would have significant implications for the Clare River catchment, which is already vulnerable to flooding. Flood estimation techniques are a key aspect in understanding and preparing for flood events. This study uses methods based on the statistical analysis of recorded data and methods based on a design rainstorm and rainfall-runoff model to estimate flood flows. These provide a mathematical basis to evaluate the impacts of various factors on flooding and also to generate practical design floods, which can be used in the design of flood relief measures. The final element of the thesis includes the author’s recommendations on how flood risk management techniques can reduce existing flood risk in the Clare River catchment. Future implications to flood risk due to factors such as climate change and poor planning practices are also considered.

Green furniture: sustainable design guidelines for the Irish furniture and wood products industry.

This thesis presents the research and development of sustainable design guidelines for the furniture and wood products industry, suitable for sustainably enhancing design, manufacturing and associated activities. This sustainable guideline is based on secondary research conducted on subject areas such as ‘eco’ design, ‘green’ branding and ‘green’ consumerism, as well as an examination of existing certifications and sustainable tools techniques and methodologies, national and international drivers for sustainable development and an overview of sustainability in the Irish furniture manufacturing context. The guideline was further developed through primary research. This consisted of a focus group attended by leading Irish designers, manufacturers and academics in the area of furniture and wood products. This group explored the question of ‘green branding’ saturation in the market and the viability of investing in sustainability just yet. Participants stated that they felt the market for ‘green’ products is evolving very slowly and that there is no metric or legal framework present to audit whether or not companies are producing products that really embody sustainability. All the participants believed that developing and introducing a new certification process to incorporate a sustainable design process was a viable and necessary solution to protecting Irish furniture and wood manufacturers going forward. For the purposes of the case study, the author investigated a ‘sustainable’ design process for Team woodcraft, Ltd., through the design and development of a ‘sustainable’ children’s furniture range. The case study followed a typical design and development process; detailing customer design specifications, concept development and refinement and cumulating in final prototype, as well as associated engineering drawings. Based on this primary and secondary research, seven fundamental core principles for this sustainable guideline have been identified by the author. The author then used these core principles to expand into guidelines for the basis of proposed new Irish sustainable design guidelines for the furniture and wood products industry, the concept of which the author has named ‘Green Dot’. The author suggests that the ‘Green Dot’ brand or logo could be used to market an umbrella network of Irish furniture designers and manufactures who implement the recommended sustainable techniques.

The concept of risk management in the renewable sector.

This study explores the perception of risk and the level of risk management implementation in the renewable sector. Risk management is emerging as a key issue due to the loss of confidence amongst banks, causing the attainment of financing to be difficult over the next few years. To attract financing, there is a fundamental requirement to manage risk in a way that minimizes the probability of a negative financial impact on the project. Miller and Lessard (2001) argue that successful projects are not selected but shaped with risk resolution in mind. Rather than evaluating projects at the outset based on projections of the full set of benefits, costs and risks over their lifetime, successful developers start with project ideas that have the potential of becoming viable. Therefore, this study bridges the gap that exists within the renewable sector in relation to risk management literature. This study succeeds through a detailed comparative case study analysis where two developers and two financiers were questioned through qualitative semi-structured interviews on the concept of risk management and its level implementation within the industry. It is believed that the growth in financed renewable energy projects depends on the adequate design and implementation of risk management to mitigate inherent project risks. However, this study revealed that are certain types of developers in existence within the renewable sector, which underestimate the magnitude of risk and view the development of projects as a ‘money racket’. Therefore, it can be concluded that perception of risk will also differ, causing risk and uncertainty to vary from project to project, resulting in investment reluctance to be associated with certain projects. The study originality lies in how it demonstrates to developers the concept of risk management, outlining the simplicity and benefits of implementing it in project development. Finally, this study contributes to the knowledge by enhancing the awareness and understanding of the presence and nature of risk in a RE project environment.

An assessment of biological and population parameters of the Common whelk, Buccinum undatum (L.) in the region of the North West Irish whelk fishery

The Common whelk, Buccinum undatum (L.) is a conspicuous benthic scavenger in Irish waters, and is a valuable fisheries resource in South East Ireland. B. undatum is fished in many parts of its range, and previous studies have shown that certain life history parameters, which vary with location, make this species vulnerable to overexploitation. This makes research into each exploited stock essential to ensure sustainable fisheries management of the species. In 2003, interest in B. undatum as a complementary species in the inshore fishery east of the Inishowen Peninsula, North West Ireland, initiated investigation into fisheries related biological and population aspects of the species in this region. The current study presents estimates of spatial variation and density of the stock, size at age and growth rates, size and age at onset of sexual maturity, and timing of reproductive events in the region of the North West Irish whelk fishery for the period of June 2003 to May 2004. Analysis of variance of the total shell length of whelk landings to the fishery was conducted over spatial scales of fishing pot, fishing string and landings to vessels. Landings varied significantly in shell length at the spatial scale at which whelks are attracted to baited pots, but did not vary significantly over larger spatial scales. Depletion estimates of stock density from fisheries derived Catch per Unit Effort data and a mark re-capture experiment estimate 0.134 - 0.227 whelks per m2. Two independent methods of age determination found similar growth logistics functions for B. undatum.Modal analysis of length frequency distribution of landings to the fishery estimated symptotic length, Leo = 151.64 mm and Brody growth coefficient, K = 0.04. Analysis of the striae in individual opercula, where each stria was found to represent annual growth, estimated Loo = 137.73 mm and K = 0.12. Common whelks in the region of the North West Irish whelk fishery grow slowly and are long-lived, with 19 opercula striae recorded in one individual. Onset of sexual maturity is late, and no sex-specific differences in size or age at maturity were determined in the present study. Males were found to achieve sexual maturity at 83.30 ± 10.77 mm, and 8.9 - 11.1 years of age, and females at 82.62 ± 10.68 mm and 8.8 to 11.1 years of age. Systematic observations of reproductive events, including histological changes to the female ovary and male testis, and changes in the size and mass of body components, suggest that breeding occurred between the autumn and winter months of October and December 2003. Biological aspects of B. undatum in the study region are compared with previous studies from other regions, and discussed in relation to sustainable management of the fishery.

The use of forensic polycyclic aromatic hydrocarbon signatures and Compound Ratio Analysis Techniques (CORAT) for the source characterisation of petrogenic/pyrogenic environmental releases.

This study utilised recent developments in forensic aromatic hydrocarbon fingerprint analysis to characterise and identify specific biogenic, pyrogenic and petrogenic contamination. The fingerprinting and data interpretation techniques discussed include the recognition of: The distribution patterns of hydrocarbons (alkylated naphthalene, phenanthrene, dibenzothiophene, fluorene, chrysene and phenol isomers), • Analysis of “source-specific marker” compounds (individual saturated hydrocarbons, including n-alkanes (n-C5 through 0-C40) • Selected benzene, toluene, ethylbenzene and xylene isomers (BTEX), • The recalcitrant isoprenoids; pristane and phytane and • The determination of diagnostic ratios of specific petroleum / non-petroleum constituents, and the application of various statistical and numerical analysis tools. An unknown sample from the Irish Environmental Protection Agency (EPA) for origin characterisation was subjected to analysis by gas chromatography utilising both flame ionisation and mass spectral detection techniques in comparison to known reference materials. The percentage of the individual Polycyclic Aromatic Hydrocarbons (PAIIs) and biomarker concentrations in the unknown sample were normalised to the sum of the analytes and the results were compared with the corresponding results with a range of reference materials. In addition, to the determination of conventional diagnostic PAH and biomarker ratios, a number of “source-specific markers” isomeric PAHs within the same alkylation levels were determined, and their relative abundance ratios were computed in order to definitively identify and differentiate the various sources. Statistical logarithmic star plots were generated from both sets of data to give a pictorial representation of the comparison between the unknown sample and reference products. The study successfully characterised the unknown sample as being contaminated with a “coal tar” and clearly demonstrates the future role of compound ratio analysis (CORAT) in the identification of possible source contaminants.

Nutritional composition, quality and spoilage capacity of orange roughy (Hoplostethus atlanticus) from the North East Atlantic

The nutritional composition o f orange roughy (collected from the Northeast Atlantic near the Rockall Trough) was studied on a seasonal basis. In addition samples were aged and stability assessed. Protein levels (16.68-16.21% w/w) were found to be slightly higher than those recorded for the N ew Zealand species o f orange roughy and compared favourably with protein values for fish muscle in general. Statistically results show a significant seasonal variation with no variation from fish to fish or in the location within the fish. Lipid content (3.6-4.5% w/w) was found to be much lower than that recorded for New Zealand. As with protein statistically results show a significant seasonal variation and no variation from fish to fish or in the location within the fish. Moisture levels (77.3_79.6%w/w) compared favourably with values obtained from other studies. Again statistically results show a significant seasonal variation with no variation from fish to fish or within the fish. Iodine values (74.63-79.54) indicate the likely presence o f a high level o f mono unsaturated fatty acids. Statistically results show no significant seasonal variation and no sample variation or variation within fish. Thin layer chromatography o f the extracted fat showed the major type to be wax esters with a much lower amount o f triglycerides and smaller amounts of polar lipids, free sterols and free fatty acids. Total fatty acid composition was found to be very similar to that recorded from other studies and showed that most o f the oils extracted from the fish muscle contained a high percentage o f mono unsaturates namely 16:1,18:1, 20:1 and 22:1 (85.63 - 91.14% ) with 16:1 present in the smallest amounts and 18:1 the major one. The only saturated fatty M.Sc. in Biochemistry III Nutritional Composition, Quality and Spoilage Capacity of Specific Deep Sea Fish acids present in significant quantities were 14:0, 16:0 and 18:0, the total varied from a seasonal average high o f 4.05 % to an average low o f 2.27%. The polyunsaturated fatty acids linoleic and arachidonic acid were present in small quantities varying in total from 0.89% to 1.50%. Docosapentaenoic acid (D P A ) was found only in trace quantities in spring, autumn and winter samples and undetected in summer. Levels o f Eicosapentaenoic acid (EPA ) and Docosahexaenoic acid (D H A ) were also found in very low percentages and varied on a seasonal basis with average values ranging from 0.41% in summer to 1.03 % in autumn for EPA and from 1.44 % in summer to3.20 % in autumn for D H A . Again statistically results show a significant seasonal variation with no variation from fish to fish or location within the fish. Levels o f freshness were measured using the Thiobarbituric acid (T B A ), Total volatile base nitrogen (T V B -N ) and Trimethylamine (T M A ) techniques. The quality o f the fish upon arrival was excellent and well below legal/acceptable lim its.T V B -N values ranged from 6.88-8.91 mg/lOOg and T M A values from 4.82-6.46 mg/lOOg Values for T B A ranged from 0.18-0.35 mg Malonaldehyde/kg fish. The summer values were higher than the other seasons. Seasonal variation was significant for all methods with no variation from fish to fish or within the fish. Fish aged at +4°C in air did not exceed the T V B N lim it o f 35mg/100g until day 6 whereas the T V B N lim it was extended to 8 days for fish aged at +4°C in vacuum. However the T M A lim it o f 12mg/100g was reached on day 4 for fish stored at +4°C in air and on day 5 for vacuum packed samples stored at +4°C . Fish stored at -5°C in air and vacuum packed did not reach the T V B N lim it until day 61 but the T M A limit was reached on day 24 for fish stored at -5°C in air and was extended to 31 days for vacuum packed fish stored at-5°C. Prolonged storage at -18°C caused some deterioration o f the frozen fish muscle. Upon thawing the shelf life o f fish stored for 12 months was much shorter than that stored for 6 M.Sc. in Biochemistry IV Nutritional Composition, Quality and Spoilage Capacity of Specific Deep Sea Fish months. This in turn deteriorated faster than fresh fish held at refridgeration temperature in air. Orange roughy were found to be a good source of protein with moisture levels similar to that o f other fish. They were o f medium fat content but have a very poor content o f the essential omega 3 and omega 6 fatty acids. Orange roughy can be stored at -18°C but its subsequent refridgerated shelf life will be shorter than that o f unfrozen orange roughy stored at refridgeration temperature. Orange roughy are a very important part o f the ecosystem. Their composition is less nutritionally beneficial than more readily available fish for human consumption and therefore should not be fished at all

An analysis of the use of photogrammetric sorting to audit construction and demolition waste production on site

This study analyses the area of construction and demolition waste (C & D W) auditing. The production of C&DW has grown year after year since the Environmental Protection Agency (EPA) first published a report in 1996 which provided data for C&D W quantities for 1995 (EPA, 1996a). The most recent report produced by the EPA is based on data for 2005 (EPA, 2006). This report estimated that the quantity of C&DW produced for that period to be 14 931 486 tonnes. However, this is a ‘data update’ report containing an update on certain waste statistics so any total provided would not be a true reflection of the waste produced for that period. This illustrates that a more construction site-specific form of data is required. The Department of Building and Civil Engineering in the Galway-Mayo Institute of Technology have carried out two recent research projects (Grimes, 2005; Kelly, 2006) in this area, which have produced waste production indicators based on site-specific data. This involved the design and testing of an original auditing tool based on visual characterisation and the application of conversion factors. One of the main recommendations of these studies was to compare this visual characterisation approach with a photogrammetric sorting methodology. This study investigates the application of photogrammetric sorting on a residential construction site in the Galway region. A visual characterisation study is also carried out on the same project to compare the two methodologies and assess the practical application in a construction site environment. Data collected from the waste management contractor on site was also used to provide further evaluation. From this, a set of waste production indicators for new residential construction was produced: □ 50.8 kg/m2 for new residential construction using data provided by the visual characterisation method and the Landfill Levy conversion factors. □ 43 kg/m2 for new residential construction using data provided by the photogrammetric sorting method and the Landfill Levy conversion factors. □ 23.8 kg/m2 for new residential construction using data provided by Waste Management Contractor (WMC). The acquisition of the data from the waste management contractor was a key element for testing of the information produced by the visual characterisation and photogrammetric sorting methods. The actual weight provided by the waste management contractor shows a significant difference between the quantities provided.

Optimising the design and manufacture of a customised, prescription fit, Maxillo-facial prosthesis

This thesis is a continuation of the Enterprise-Ireland Research Innovation Fund (RIF) Project entitled’ "Design and Manufacturing of Customised Maxillo-Facial Prostheses" The primary objective of this Internal Research Development Program (IRDP) project was to investigate two fundamental design changes 1 To incorporate the over-denture abutments directly into the implant. 2 To remove the restraining wings by the addition of screws, which affix the. implant to the dense material of the jawbone. The prosthetic was redesigned using the ANSYS Finite Element Analysis software program and analysed to* • Reduce the internal von Mises stress distribution The new prosthetic had a -63.63 % lower von Mises stress distribution when compared with the original prosthetic. • Examine the screw preload effects. A maximum relative displacement of 22 6 * lO^mm between the bone and screw was determined, which is well below the critical threshold of micromotion which prevents osseointegration • Investigate the prosthetic-bone contact interface. Three models of the screw, prosthesis, and bone, were studied. (Axisymmetnc, quarter volume, and full volume), a recommended preload torque of 0 32 Nm was applied to the prosthetic and a maximum von Mises stress of 1.988 MPa was predicted • Study the overdenture removal forces. This analysis could not be completed because the correct plastic multilinear properties of the denture material could not be established The redesigned prosthetic was successfully manufactured on a 3-axis milling machine with an indexing system The prosthetic was examined for dimensional quality and strength The research established the feasibility of the new design and associated manufacturing method.

Development of a data acquisition system to characterise sustainable energy technologies and to support Web-Based learning (DAQ-WBL)

Driven by concerns about rising energy costs, security of supply and climate change a new wave of Sustainable Energy Technologies (SET’s) have been embraced by the Irish consumer. Such systems as solar collectors, heat pumps and biomass boilers have become common due to government backed financial incentives and revisions of the building regulations. However, there is a deficit of knowledge and understanding of how these technologies operate and perform under Ireland’s maritime climate. This AQ-WBL project was designed to address both these needs by developing a Data Acquisition (DAQ) system to monitor the performance of such technologies and a web-based learning environment to disseminate performance characteristics and supplementary information about these systems. A DAQ system consisting of 108 sensors was developed as part of Galway-Mayo Institute of Technology’s (GMIT’s) Centre for the Integration of Sustainable EnergyTechnologies (CiSET) in an effort to benchmark the performance of solar thermal collectors and Ground Source Heat Pumps (GSHP’s) under Irish maritime climate, research new methods of integrating these systems within the built environment and raise awareness of SET’s. It has operated reliably for over 2 years and has acquired over 25 million data points. Raising awareness of these SET’s is carried out through the dissemination of the performance data through an online learning environment. A learning environment was created to provide different user groups with a basic understanding of a SET’s with the support of performance data, through a novel 5 step learning process and two examples were developed for the solar thermal collectors and the weather station which can be viewed at http://www.kdp 1 .aquaculture.ie/index.aspx. This online learning environment has been demonstrated to and well received by different groups of GMIT’s undergraduate students and plans have been made to develop it further to support education, awareness, research and regional development.

An investigation into system security requirements and implementation in an Application Service Provider (ASP) environment

Although the ASP model has been around for over a decade, it has not achieved the expected high level of market uptake. This research project examines the past and present state of ASP adoption and identifies security as a primary factor influencing the uptake of the model. The early chapters of this document examine the ASP model and ASP security in particular. Specifically, the literature and technology review chapter analyses ASP literature, security technologies and best practices with respect to system security in general. Based on this investigation, a prototype to illustrate the range and types of technologies that encompass a security framework was developed and is described in detail. The latter chapters of this document evaluate the practical implementation of system security in an ASP environment. Finally, this document outlines the research outputs, including the conclusions drawn and recommendations with respect to system security in an ASP environment. The primary research output is the recommendation that by following best practices with respect to security, an ASP application can provide the same level of security one would expect from any other n-tier client-server application. In addition, a security evaluation matrix, which could be used to evaluate not only the security of ASP applications but the security of any n-tier application, was developed by the author. This thesis shows that perceptions with regard to fears of inadequate security of ASP solutions and solution data are misguided. Finally, based on the research conducted, the author recommends that ASP solutions should be developed and deployed on tried, tested and trusted infrastructure. Existing Application Programming Interfaces (APIs) should be used where possible and security best practices should be adhered to where feasible.

Instrumentation and software for the VERITAS Project and the detection of TeV Gamma-Ray Emission from the BL Lacertae Object 1ES1959+650

Transmission of Cherenkov light through the atmosphere is strongly influenced by the optical clarity of the atmosphere and the prevailing weather conditions. The performance of telescopes measuring this light is therefore dependent on atmospheric effects. This thesis presents software and hardware developed to implement a prototype sky monitoring system for use on the proposed next-generation gamma-ray telescope array, VERITAS. The system, consisting of a CCD camera and a far-infrared pyrometer, was successfully installed and tested on the ten metre atmospheric Cherenkov imaging telescope operated by the VERITAS Collaboration at the F.L. Whipple Observatory in Arizona. The thesis also presents the results of observations of the BL Lacertae object, 1ES1959+650, made with the Whipple ten metre telescope. The observations provide evidence for TeV gamma-ray emission from the BL Lacertae object, 1ES1959+650, at a level of more than 15 standard deviations above background. This represents the first unequivocal detection of this object at TeV energies, making it only the third extragalactic source seen at such levels of significance in this energy range. The flux variability of the source on a number of timescales is also investigated.

Synchronous reproduction may facilitate introgression in a hybrid mussel (Mytilus) population

Mussel populations on the Irish Atlantic coast comprise an interbreeding mixture of the blue mussel, Mytilus edulis (L.) and the Mediterranean mussel, Mytilus galloprovincialis (Lmk.). The occurrence of hybrid genotypes varies between sites but can be as high 80%. This study compares the reproductive cycle of M. edulis, M. galloprovincialis and their hybrids to determine if the extensive hybridisation observed at Irish Atlantic coast sites is linked to spawning synchrony between the two taxa. Mussels (40-45 mm size class) were collected monthly from a sheltered shore in Galway Bay from January to December 2005. Two major spawning events (March- June and September-October) were observed and gametogenesis took place throughout the year. The spawning cycles of the three taxa were largely overlapping. Small differences were observed in the timing of peak spawning which occurred in March and October in M. galloprovincialis and in May-June and September in M.edulis. Spawning of hybrid individuals was intermediate between the parental genotypes. Fecundity was slightly higher in M. galloprovincialis females compared to the other taxa (up to 30% difference, p<0.05). This apparent advantage is not shared by the sexes and is likely being offset by high numbers of hybrid genotypes releasing gametes during peak spawning of M. galloprovincialis. There was no evidence for increased mortality in hybrid males; sex ratios did not deviate from the 1:1 ratio. The results show that in this region of the hybrid zone the timing of reproduction does not present a barrier to gene flow between M. edulis and M. galloprovincialis. Nonetheless, small differences in the timing of peak spawning may increase the likelihood of conspecific fertilisation at certain times of the year. Hybrids outnumber the parental genotypes, undergo complete gametogenesis and show no evidence of depressed fitness (i.e. hybrids are reproductively competent suggesting a high degree of introgression.