U.S. government environmental datafiles & software : microcomputers & mainframes.

"3/94"--P [4] of cover.

An investigation of thin amorphous carbon-based sputtered coatings for MEMS and micro-engineering applications

The work presented in this thesis describes an investigation into the production and properties of thin amorphous C films, with and without Cr doping, as a low wear / friction coating applicable to MEMS and other micro- and nano-engineering applications. Firstly, an assessment was made of the available testing techniques. Secondly, the optimised test methods were applied to a series of sputtered films of thickness 10 - 2000 nm in order to: (i) investigate the effect of thickness on the properties of coatingslcoating process (ii) investigate fundamental tribology at the nano-scale and (iii) provide a starting point for nanotribological coating optimisation at ultra low thickness. The use of XPS was investigated for the determination of Sp3/Sp2 carbon bonding. Under C 1s peak analysis, significant errors were identified and this was attributed to the absence of sufficient instrument resolution to guide the component peak structure (even with a high resolution instrument). A simple peak width analysis and correlation work with C KLL D value confirmed the errors. The use of XPS for Sp3/Sp2 was therefore limited to initial tentative estimations. Nanoindentation was shown to provide consistent hardness and reduced modulus results with depth (to < 7nm) when replicate data was suitably statistically processed. No significant pile-up or cracking of the films was identified under nanoindentation. Nanowear experimentation by multiple nanoscratching provided some useful information, however the conditions of test were very different to those expect for MEMS and micro- / nano-engineering systems. A novel 'sample oscillated nanoindentation' system was developed for testing nanowear under more relevant conditions. The films were produced in an industrial production coating line. In order to maximise the available information and to take account of uncontrolled process variation a statistical design of experiment procedure was used to investigate the effect of four key process control parameters. Cr doping was the most significant control parameter at all thicknesses tested and produced a softening effect and thus increased nanowear. Substrate bias voltage was also a significant parameter and produced hardening and a wear reducing effect at all thicknesses tested. The use of a Cr adhesion layer produced beneficial results at 150 nm thickness, but was ineffective at 50 nm. Argon flow to the coating chamber produced a complex effect. All effects reduced significantly with reducing film thickness. Classic fretting wear was produced at low amplitude under nanowear testing. Reciprocating sliding was produced at higher amplitude which generated three body abrasive wear and this was generally consistent with the Archard model. Specific wear rates were very low (typically 10-16 - 10-18 m3N-1m-1). Wear rates reduced exponentially with reduced film thickness and below (approx.) 20 nm, thickness was identified as the most important control of wear.

Adhesive bonding of aluminium

Adhesive bonding of aluminium is widely used in the aerospace industry. High initial bood strengths can be obtained, but bond failure occurs atter prolonged exposure to humid enviroments. The thesis contains details ot a test procedure which has been designed and developed for the assessment of different alloys, pretreatments, and adhesives, which will give adhesively bonded aluminium joints of high strength coupled with long term durability. The test involves assembly of lap shear specimens in a precision jig using 250 ballotini spacers in the adhesive to control the bond line thickness. The test is modified by drilling three accurately located holes through the bonded area after assembly of the joint and curing of the adhesive. Further important features at the test, such as fillet control, are detailed. The test was assessed, modified and developed to give a reliable and reproducible method which would discriminate amongst different bonding systems after exposure to humid test environments. This is the first test to have achieved the discrimination necessary for short term assessment of bond systems where long term durability is required. Even better discrimination has been obtained by applying stress in a stress humidity test. Having established accurate, reliable and discriminating test methods they were used to study the durability of structural epoxy adhesive bonds to aluminium as a function of alloy, pretreatment, adhesive and environment. It was established that the long term durability or adhesively bonded aluminium was directly related to the infulence of water migrating within the adhesive. Pretreatments differed in their ability to prevent hydration of the aluminium oxide by the water absorbed within the adhesive.

Abrasion resistance of fibre reinforced concrete floors

This thesis focuses on the investigation of the abrasion resistance of fibre reinforced concrete floors at both the macro and micro levels. A literature review of the available literature concerning subjects allied to the current project is included. This highlights themes relevant to wear mechanisms and the factors influencing it: factors that affect the abrasion resistance of concrete and several test methods for assessing it; and the historical development of fibres and the properties of different fibre types and their influence on concrete. Three accelerated abrasion testers were compared and critically discussed for their suitability for assessing the abrasion resistance of concrete floors. Based on the experimental findings one accelerated abrasion apparatus was selected as more appropriate to be used for carrying out the main investigations. The laboratory programme that followed was undertaken to investigate the influence of various material and construction factors on abrasion resistance. These included mix variations (w/c ratio), fibre reinforcement, geometry, type and volume, curing method and superplasticizing agents. The results clearly show that these factors significantly affected abrasion resistance and several mechanisms were presumed to explain and better understand these observations. To verify and understand these mechanisms that are accountable for the breakdown of concrete slabs, the same concrete specimens that were used for the macro-study, were also subjected to microstructutural investigations using techniques such as Microhardness examination, Mercury intrusion porosimetry and Petrographic examination. It has been found that the abrasion resistance of concrete is primarily dependent on the microstructure and porosity of the concrete nearest to the surface. The feasibility of predicting the abrasion resistance of fibre reinforced concrete floors by indirect and non-destructive methods was investigated using five methods that have frequently been used for assessing the quality of concrete. They included the initial surface absorption test, the impact test, ball cratering, the scratch test and the base hardness test. The impact resistance (BRE screed tester) and scratch resistance (Base hardness tester) were found to be the most sensitive to factors affecting abrasion resistance and hence are considered to be the most appropriate testing techniques. In an attempt to develop an appropriate method for assessing the abrasion resistance of heavy-duty industrial concrete floors, it was found that the presence of curing/sealing compound on the concrete surface at the time of accelerated abrasion testing produces inappropriate results. A preliminary investigation in the direction of modifying the Aston accelerated abrasion tester has been carried out and a more aggressive head has been developed and is pending future research towards standardisation.

Settlement of fill with particular reference to opencast coal mining sites

A study of information available on the settlement characteristics of backfill in restored opencast coal mining sites and other similar earthworks projects has been undertaken. In addition, the methods of opencast mining, compaction controls, monitoring and test methods have been reviewed. To consider and develop the methods of predicting the settlement of fill, three sites in the West Midlands have been examined; at each, the backfill had been placed in a controlled manner. In addition, use has been made of a finite element computer program to compare a simple two-dimensional linear elastic analysis with field observations of surface settlements in the vicinity of buried highwalls. On controlled backfill sites, settlement predictions have been accurately made, based on a linear relationship between settlement (expressed as a percentage of fill height) against logarithm of time. This `creep' settlement was found to be effectively complete within 18 months of restoration. A decrease of this percentage settlement was observed with increasing fill thickness; this is believed to be related to the speed with which the backfill is placed. A rising water table within the backfill is indicated to cause additional gradual settlement. A prediction method, based on settlement monitoring, has been developed and used to determine the pattern of settlement across highwalls and buried highwalls. The zone of appreciable differential settlement was found to be mainly limited to the highwall area, the magnitude was dictated by the highwall inclination. With a backfill cover of about 15 metres over a buried highwall the magnitude of differential settlement was negligible. Use has been made of the proposed settlement prediction method and monitoring to control the re-development of restored opencase sites. The specifications, tests and monitoring techniques developed in recent years have been used to aid this. Such techniques have been valuable in restoring land previously derelict due to past underground mining.

Estudo sobre tratamento térmico e mudança superficial da diatomita de Punaú/RN para o desenvolvimento de um auxiliar de filtração

The diatomite is a natural material that has numerous applications due to changes in their physical and chemical properties after processing. It is currently used in the industry as a sound insulator , filter aid and industrial load . The filter material shall be inert chemical composition , which will diatomite confers a high commercial value and performance not found in other particulate materials , for this application. The diatomite surface undergoes changes after thermal treatment at high temperatures , from 800ºC , with properties that enable its application in the food , beverage , pharmaceutical , cosmetic and textiles . In this work , we developed a study on thermal treatment on natural diatomite to adapt their properties to the application as a filter aid . The heat treatments were performed in an open oven at temperatures of 800ºC , 1000ºC and 1200ºC for a time of 24 hours. Reagents were added in the constitution of the samples analyzed. The reagents used were sodium carbonate (Na2CO3 ) and sodium chloride (NaCl) . The samples were characterized by x - ray diffraction , x -ray fluorescence , scanning electron microscopy , analysis and particle size distribution , specific surface area by the BET method , and pore volume by BJH method. The results showed a reduction in porosity of the material as well as a significant increase in specific surface area after heat treatment and the reactants in the ratio of 3 wt%. The diatomaceous earth , after heat treatment , undergone changes in its coloration , varying in white, cream and beige , which directly interferes with the speed of filtration materials process. All results obtained before and after heat treatment of the material with the values obtained for samples already used industrially , Brazilian and American industry , which were characterized using the same test methods performed with the samples in the study were compared and showed promising efficiency when material studied in the region of Punaú - RN , after processing , reagent addition and heat treatment, as an element in the composition of filter .

Normalização de eletromiografia de superfície dos músculos respiratórios em sujeitos saudáveis: contração voluntária máxima máxima isométrica versus pressões respiratórias máximas

Aim : To evaluate and to standardize surface electromyography (sEMG) normalization procedures for respiratory muscles by comparing muscle activation during Maximal Voluntary Isometric Contraction (MVIC) and Maximal Respiratory Pressures (MIP, MEP and sniff test). Methods: Healthy subjects were evalua ted regarding demographics, spirometry and sEMG during the five maneuvers: sniff test, MIP , MEP and Maximal Voluntary Isometric C ontraction (MVIC) of RA, SCM and SC A . For electrode placement, skin was prepared with abrasion, followed by shaving in the foll owing regions for acquisition of el ectromyographic signals: (1) SC M: lower third of the distance between the mastoid process and t he sternoclavicular joint; (2) SC A : 5 cm to the right from the sternoclavicular joint and at this point, up to 2 cm; and (3 ) RA: the level of umbilicus, 4 cm to the right. In electromyographic variables analysis , the data normality was assessed by Shapiro - Wilk test. Comparisons among studied maneuvers were performed by Friedman Test and Dunn’s post - hoc for multiple comparisons a mong inspiratory maneuvers, and Mann Whitney test for expiratory maneuvers. Subgroups differences between genders were performed by Student's t test or Mann - Whitney test according to data normality. Results: 35 subjects participated in the study, b ut 5 we re excluded (BMI> 25 kg/ m²). Sample consisted of 30 subjects (1 5 women), mean age 27.3±7.43 years, BMI 22.2 ± 1.69 kg/m² and spirometric indices within normal limits. Specific MVIC for SCM, SCA and RA showed the highest RMS. When we grouped sample into gender we found no difference among RMS values for the studied SCM maneuvers, while for SCA, MVIC SCM / SCA was the one with the highest RMS and for RA, MVIC RA in men. Once considering women, MVIC SCM/SCA showed the highest RMS for SCM, SCA and MVIC RA showed t he highest value for RA. Conclusion: MVIC for SCM, SCA and RA muscles showed the highest RMS values. When comparing RMS between the studied groups, there was no significant difference between men and women.

Testing of Interposer-Based 2.5D Integrated Circuits

The unprecedented and relentless growth in the electronics industry is feeding the demand for integrated circuits (ICs) with increasing functionality and performance at minimum cost and power consumption. As predicted by Moore's law, ICs are being aggressively scaled to meet this demand. While the continuous scaling of process technology is reducing gate delays, the performance of ICs is being increasingly dominated by interconnect delays. In an effort to improve submicrometer interconnect performance, to increase packing density, and to reduce chip area and power consumption, the semiconductor industry is focusing on three-dimensional (3D) integration. However, volume production and commercial exploitation of 3D integration are not feasible yet due to significant technical hurdles.

At the present time, interposer-based 2.5D integration is emerging as a precursor to stacked 3D integration. All the dies and the interposer in a 2.5D IC must be adequately tested for product qualification. However, since the structure of 2.5D ICs is different from the traditional 2D ICs, new challenges have emerged: (1) pre-bond interposer testing, (2) lack of test access, (3) limited ability for at-speed testing, (4) high density I/O ports and interconnects, (5) reduced number of test pins, and (6) high power consumption. This research targets the above challenges and effective solutions have been developed to test both dies and the interposer.

The dissertation first introduces the basic concepts of 3D ICs and 2.5D ICs. Prior work on testing of 2.5D ICs is studied. An efficient method is presented to locate defects in a passive interposer before stacking. The proposed test architecture uses e-fuses that can be programmed to connect or disconnect functional paths inside the interposer. The concept of a die footprint is utilized for interconnect testing, and the overall assembly and test flow is described. Moreover, the concept of weighted critical area is defined and utilized to reduce test time. In order to fully determine the location of each e-fuse and the order of functional interconnects in a test path, we also present a test-path design algorithm. The proposed algorithm can generate all test paths for interconnect testing.

In order to test for opens, shorts, and interconnect delay defects in the interposer, a test architecture is proposed that is fully compatible with the IEEE 1149.1 standard and relies on an enhancement of the standard test access port (TAP) controller. To reduce test cost, a test-path design and scheduling technique is also presented that minimizes a composite cost function based on test time and the design-for-test (DfT) overhead in terms of additional through silicon vias (TSVs) and micro-bumps needed for test access. The locations of the dies on the interposer are taken into consideration in order to determine the order of dies in a test path.

To address the scenario of high density of I/O ports and interconnects, an efficient built-in self-test (BIST) technique is presented that targets the dies and the interposer interconnects. The proposed BIST architecture can be enabled by the standard TAP controller in the IEEE 1149.1 standard. The area overhead introduced by this BIST architecture is negligible; it includes two simple BIST controllers, a linear-feedback-shift-register (LFSR), a multiple-input-signature-register (MISR), and some extensions to the boundary-scan cells in the dies on the interposer. With these extensions, all boundary-scan cells can be used for self-configuration and self-diagnosis during interconnect testing. To reduce the overall test cost, a test scheduling and optimization technique under power constraints is described.

In order to accomplish testing with a small number test pins, the dissertation presents two efficient ExTest scheduling strategies that implements interconnect testing between tiles inside an system on chip (SoC) die on the interposer while satisfying the practical constraint that the number of required test pins cannot exceed the number of available pins at the chip level. The tiles in the SoC are divided into groups based on the manner in which they are interconnected. In order to minimize the test time, two optimization solutions are introduced. The first solution minimizes the number of input test pins, and the second solution minimizes the number output test pins. In addition, two subgroup configuration methods are further proposed to generate subgroups inside each test group.

Finally, the dissertation presents a programmable method for shift-clock stagger assignment to reduce power supply noise during SoC die testing in 2.5D ICs. An SoC die in the 2.5D IC is typically composed of several blocks and two neighboring blocks that share the same power rails should not be toggled at the same time during shift. Therefore, the proposed programmable method does not assign the same stagger value to neighboring blocks. The positions of all blocks are first analyzed and the shared boundary length between blocks is then calculated. Based on the position relationships between the blocks, a mathematical model is presented to derive optimal result for small-to-medium sized problems. For larger designs, a heuristic algorithm is proposed and evaluated.

In summary, the dissertation targets important design and optimization problems related to testing of interposer-based 2.5D ICs. The proposed research has led to theoretical insights, experiment results, and a set of test and design-for-test methods to make testing effective and feasible from a cost perspective.

Text-messaging as a Tool for Medication Adherence and Behavior Change in Disease Management among Patients with Coronary Heart Disease

Background: Evidence-based medication and lifestyle modification are important for secondary prevention of cardiovascular disease but are underutilized. Mobile health strategies could address this gap but existing evidence is mixed. Therefore, we piloted a pre-post study to assess the impact of patient-directed text messages as a means of improving medication adherence and modifying major health risk behaviors among coronary heart disease (CHD) patients in Hainan, China.

Methods: 92 CVD patients were surveyed between June and August 2015 (before the intervention) and then between October and December 2015 (after 12 week intervention) about (a) medication use (b) smoking status,(c) fruit and vegetable consumption, and (d) physical activity uptake. Acceptability of text-messaging intervention was assessed at follow-up. Descriptive statistics, along with paired comparisons between the pre and post outcomes were conducted using both parametric (t-test) and non-parametric (Wilcoxon signed rank test) methods.

Results: The number of respondents at follow-up was 82 (89% retention rate). Significant improvements were observed for medication adherence (P<0.001) and for the number of cigarettes smoked per day (P=.022). However there was no change in the number of smokers who quitted smoking at follow-up. There were insignificant changes for physical activity (P=0.91) and fruit and vegetable consumption.

RELATIONSHIP BETWEEN PHYSICAL AND CHEMICAL PROPERTIES OF STRAIGHT AND RECOVERED ASPHALT BINDERS FROM ONTARIO

Thermal and fatigue cracking are the major pavement distresses that contribute to a drastic reduction of the pavement’s service life and performance in Ontario. Chemical oxidation and hardening of asphalt binders deteriorates its physical properties since physical properties of asphalts depend on its chemical composition. This thesis is aimed to establish a relationship between physical and chemical properties of asphalt binders. A secondary objective is to show the strong correlation between CTOD and temperature. All recovered and straight Ministry of Transportation of Ontario (MTO) samples were investigated using conventional Superpave® test method dynamic shear rheometer (DSR) as well as improved MTO test methods such as extended bending beam rheometer (eBBR) and double-edge-notched tension (DENT) test. DENT test was conducted for all Ontario contract samples at three different temperatures based on their performance grade after three hours of thermal conditioning and compared the results in terms of essential work of fracture, plastic work of fracture and CTOD at different temperatures. Good correlation exists between CTOD and temperature according to the DENT data. X-ray fluorescence (XRF) analysis was conducted to detect the presence of heavy metals such as zinc and molybdenum believed to have originated from waste engine oil. Fourier transform infra-red spectroscopy (FTIR) was performed to determine the abundance of functional groups such as carbonyl, sulfoxides, polyisobutylene, etc. XRF and FTIR analysis confirmed that most of the samples contain waste engine oil and/or oxidized residues, which is believed to be a root cause of premature pavement failures.

The Pico de Navas slump (Burgos, Spain): a large rocky landslide caused by underlying clayey sand fluidification

The Pico de Navas landslide was a large-magnitude rotational movement, affecting 50x106m3 of hard to soft rocks. The objectives of this study were: (1) to characterize the landslide in terms of geology, geomorphological features and geotechnical parameters; and (2) to obtain an adequate geomechanical model to comprehensively explain its rupture, considering topographic, hydro-geological and geomechanical conditions. The rupture surface crossed, from top to bottom: (a) more than 200 m of limestone and clay units of the Upper Cretaceous, affected by faults; and (b) the Albian unit of Utrillas facies composed of silty sand with clay (Kaolinite) of the Lower Cretaceous. This sand played an important role in the basal failure of the slide due to the influence of fine particles (silt and clay), which comprised on average more than 70% of the sand, and the high content presence of kaolinite (>40%) in some beds. Its geotechnical parameters are: unit weight (δ) = 19-23 KN/m3; friction angle (φ) = 13º-38º and cohesion (c) = 10-48 KN/m2. Its microstructure consists of accumulations of kaolinite crystals stuck to terrigenous grains, making clayey peds. We hypothesize that the presence of these aggregates was the internal cause of fluidification of this layer once wet. Besides the faulted structure of the massif, other conditioning factors of the movement were: the large load of the upper limestone layers; high water table levels; high water pore pressure; and the loss of strength due to wet conditions. The 3D simulation of the stability conditions concurs with our hypothesis. The landslide occurred in the Recent or Middle Holocene, certainly before at least 500 BC and possibly during a wet climate period. Today, it appears to be inactive. This study helps to understand the frequent slope instabilities all along the Iberian Range when facies Utrillas is present.

Developing an engineering approach for migrating from prescriptive to performance-based specification for concrete

The integral variability of raw materials, lack of awareness and appreciation of the technologies for achieving quality control and lack of appreciation of the micro and macro environmental conditions that the structures will be subjected, makes modern day concreting a challenge. This also makes Designers and Engineers adhere more closely to prescriptive standards developed for relatively less aggressive environments. The data from exposure sites and real structures prove, categorically, that the prescriptive specifications are inadequate for chloride environments. In light of this shortcoming, a more pragmatic approach would be to adopt performance-based specifications which are familiar to industry in the form of specification for mechanical strength. A recently completed RILEM technical committee made significant advances in making such an approach feasible.
Furthering a performance-based specification requires establishment of reliable laboratory and on-site test methods, as well as easy to perform service-life models. This article highlights both laboratory and on-site test methods for chloride diffusivity/electrical resistivity and the relationship between these tests for a range of concretes. Further, a performance-based approach using an on-site diffusivity test is outlined that can provide an easier to apply/adopt practice for Engineers and asset managers for specifying/testing concrete structures.

Propriedades Psicométricas do Teste Stroop numa Amostra de Adultos da População Portuguesa: estudo preliminar

Objetivos: O presente estudo insere-se no Projeto - Estudos Normativos de Instrumentos Neuropsicologicos (ENIN) e tem por objetivo analisar as propriedades psicométricas do Teste Stroop, fornecendo dados normativos de uma amostra da População Portuguesa. Métodos: Selecionámos e inquirimos 671 sujeitos. As variáveis independentes estudadas foram idade, sexo, escolaridade e profissão. Foram utilizados vários testes neste estudo, contribuindo para a obtenção de validade convergente: Bateria de Avaliação Frontal-FAB, Figura Complexa de Rey-Osterrieth e Teste do Relógio. Foram estudadas a consistência interna e a estabilidade temporal do Teste Stroop. Resultados: A nossa amostra ficou constituída por 310 sujeitos (46,2%) do sexo masculino e 361 (53,8%) do sexo feminino, com idades compreendidas entre os 18 e 100 anos (M = 41,12; DP = 20,85). No que se refere ao nível de escolaridade (M = 5,71; DP = 1,45), este variou entre o 1º Ciclo do Ensino Básico e o Ensino Superior. As profissões, exercidas inseriram-se maioritariamente na categoria das profissões intelectuais (N = 281; 84,9%). Relativamente às variáveis sociodemográficas, verificámos que a idade, sexo, escolaridade e profissão influenciam nas provas de Leitura e Nomeação de Cor do Teste Stroop. No que diz respeito à validade convergente, observámos que a prova de Nomeação de Cor apresentou correlações positivas fracas com o FAB, Figura Complexa de Rey-Cópia (FCR-Cópia) e Teste do Relógio, e correlações positivas moderadas com a prova de Leitura. A consistência interna do Teste Stroop apresentou uma elevada confiabilidade (α = 0,99). A correlação teste-reteste apenas se mostrou significativa para a prova de Nomeação de Cor. Conclusão: Este estudo mostra que o Teste Stroop é promissoriamente confiável como instrumento de avaliação neuropsicológica, podendo potencialmente ser utilizado para qualquer faixa etária da população. Em estudos futuros são necessárias amostras com números mais elevados de participantes nas faixas etárias acima dos 30 anos, representativas dos níveis de escolaridade abaixo do 9ºano, a exercerem profissões manuais, e com residência noutras regiões geográficas para além do Centro. / Objectives: The present study is part of the Project - Estudos Normativos de Instrumentos Neuropsicologicos (ENIN) and aims to analyze the psychometric properties of the Stroop test. Methods: We have selected, and we also enquired 671 subjects. The independent variables studied were age, gender, education and profession. Several tests were used in this study for analysis of convergent validity: convergent validity: Frontal Assessment Battery-FAB, Complex Figure Rey-Osterrieth and the clock test. We also studied the internal consistency and the temporal stability of the Stroop test. Results: Our sample was composed of 310 subjects (46.2%) male and 361 (53.8%) females, with ages between 18 and 100 years (M = 41.12; SD = 20.85). The level of schooling (M = 5.71; SD = 1.45) ranged between the 1st cycle and the Higher Education. The professions were mainly intellectual ones (N = 281; 84.9%). On sociodemographic variables, we found that the age, sex, education and profession influenced reading and Color naming of Stroop test. Regarding convergent validity, Color naming showed weak positive correlations with the FAB, Complex Figure Rey-Copy, and the clock test. Color naming moderate positive correlations with the reading. The internal consistency of the Stroop test was high (α = 0.99). The test-retest correlation was significant only for Color naming. Conclusion: This study shows that the Stroop test is promissory reliable instrument of neuropsychological assessment and may potentially be used for any age range of the population. In future research, it is necessary to enroll samples with higher numbers of participants above 30 years, representative of the levels of schooling below the 9º grade, with more manual professions represented, and with residence in other geographic regions in addition to the Center region of Portugal.

Manganese toxicity in Portuguese Cambisols derived from granite: causes, limitations of soil analyses and possible solutions

Cambisols are the major soil type in Portugal. The yield of annual crops in these soils is generally poor, and the situation is aggravated in wet winters. In the south of Portugal, manganese toxicity has been identified as the major cause of poor growth and leaching as the main reason for the negative effect of rainfall observed in Cambisols derived from granite Manganese toxicity also appears to be present in the Cambisols in other regions of Portugal. Manganese toxicity is cross-related to the magnesium concentration, either in the soil solution or in plant shoots. Therefore soil amendment using dolomitic limestone is needed to overcome the problem. Current soil test methods are unable to predict the level of Mn toxicity. However, new approach using the extraction of soil solution is proposed, although further work is needed to fully implement the method.

Prática de ensino supervisionada relativo ao ano letivo 2014/2015, realizada na Escola Básica de 2º e 3º ciclos com Ensino Secundário Cunha Rivara

O presente relatório é fruto da Prática de Ensino Supervisionada, realizada no ano letivo 2014/2015 na Escola Básica 2, 3 com Ensino Secundário Cunha Rivara, no âmbito do Mestrado em Ensino do Português no 3.º Ciclo do Ensino Básico e Ensino Secundário e de Espanhol nos Ensinos Básico e Secundário, sob a orientação do Professor Doutor António Ricardo Mira. Esta fase prática do mestrado assume-se como momento charneira na formação de futuros professores, porquanto representa o espaço ideal para aferir e testar métodos e técnicas aplicáveis aos processos de ensino/aprendizagem. Nesse sentido, e partindo do pressuposto de que o aluno deve ser o ator principal ao longo deste processo, este relatório assume uma função descritiva, mas, em simultâneo, outra dimensão, tão ou mais importante, no domínio da reflexão e da interiorização de práticas pedagógico-didáticas e de comportamentos relacionais, assumidos durante este processo. Assim, desenvolve-se em cinco componentes, que se complementam: preparação científica, pedagógica e didática; planificação e condução de aulas e avaliação de aprendizagens; análise da prática de ensino; participação na escola e desenvolvimento profissional; ABSTRACT: This report is the result of Supervised Teaching Practice, held in the school year 2014/2015 at the Basic and Secondary School 2, 3 “Cunha Rivara”, within the Master degree: “Teaching Portuguese in the 3rd cycle of Basic Education and Secondary Education and Spanish in basic and secondary education”, under the guidance of Professor Ricardo Antonio Mira. This practice of master stage is assumed as a key moment in the training of future teachers, because it is the ideal place and moment to measure and test methods and techniques applicable to teaching / learning processes. Accordingly, and assuming that the student must be the main actor throughout this process, this report takes a descriptive function, but at the same time, another dimension, equally important in the field of reflection and practices internalization, pedagogical-didactic and relational behaviors made during this process. Thus it develops into five components, which complement each other: scientific, pedagogical and didactic preparation; planning and conducting classes and learning evaluation; analysis of the teaching practice; participation in school and professional development.