Removal of dyes by lignocellulose adsorbents originating from biodiesel production

In this study, use was made of tucumã cake, in natura (TCN) and thermally treated (TCT), as potential alternative adsorbents for the adsorption of cationic and anionic dyes. The effects of the parameters: contact time, adsorbent: adsorbate mass ratio, and initial concentration of dye were analyzed. The adsorption isotherms were established from optimized adsorption parameters. The best conditions for adsorption were: equilibrium time of 7 h, concentration of 25 mg L 1 and ratio of 1:200 for the methylene blue dye; and pH 6.5, concentration of 25 mg L 1 and ratio of 1:200 for the congo red dye. The adsorption process was best represented by the Dubinin–Radushkevich and Sips isotherms. The kinetics of adsorption of the dyes were best described by the pseudo-second-order kinetic and Elovich models. TCT showed the best maximum adsorption capacity (Qm) for the methylene blue dye (63.92 mg g 1 ).

Using ionic liquid combined with HPLC-DAD to analyze semi-permanent hair dyes in commercial formulations

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Determination of water insoluble dyes used as marking of commercial petroleum products using high-performance liquid chromatography with electrochemical detection

This paper describes an analytical method using high-performance liquid chromatographic (HPLC) separationcoupled with electrochemical detection to detect three dyes, Solvent Blue 14 (SB-14), Solvent Blue 35 (SB-35) andSolvent Red 24 (SR-24). The dyes were eluted and separated using a reversed-phase column (C-8) under isocraticelution with the mobile phase containing a mixture of acetonitrile/ammonium acetate (5.0 mmol L1) at the ratio of75: 25 (v/v). Two sample pretreatment methods were tested and successfully applied to quantify SB14, SB-35 and SR-24 dyes in gasoline samples. The proposed method was simple, fast and suitable to detect and quantify marker dyes ingasoline sample at low concentration.

Using SPE-LC-ESI-MS/MS analysis to assess disperse dyes in environmental water samples

We have optimized an SPE-LC-ESI-MS/MS method and used it to monitor disperse azo dyes in environmental aquatic samples. Calibration curves constructed for nine disperse dyes-Red 1, Violet 93, Blue 373, Orange 1, Orange 3, Orange 25, Yellow 3, Yellow 7 and Red 13-in aqueous solution presented good linearity between 2.0 and 100.0 ng mL(-1). The method provided limits of detection and quantification around 2.0 and 8.0 ng L(-1), respectively. For dyes at concentrations of 25.0 ng mL(-1), the intra- and interday analyses afforded relative standard deviation lower than 6 and 13%, respectively. The recovery values obtained for each target analyte in Milli-Q water, receiving waters and treated water samples spiked with the nine studied dyes at concentrations of 8.0, 25.0 and 50.0 ng L(-1) (n = 3) gave average recoveries greater than 70%, with RSD <20%. Statistical evaluation aided method validation. The validated method proved to be useful for analysis of organic extracts from effluents and receiving water samples after an SPE extraction step. More specifically, the method enabled detection of the dyes Disperse Red 1, Disperse Blue 373 and Disperse Violet 93 at concentrations ranging from 84 to 3452 ng L(-1) in the treated effluent (TE), affluent and points collected upstream and downstream of the drinking water treatment plant of a textile dye industry in Brazil.

Cytotoxic and genotoxic effects of two hair dyes used in the formulation of black color

According to the International Agency for Research on Cancer (IARC), some hair dyes are considered mutagenic and carcinogenic in in vitro assays and exposed human populations. Epidemiological studies indicate that hairdressers occupationally exposed to hair dyes have a higher risk of developing bladder cancer. In Brazil, 26% of the adults use hair dye. In this study, we investigated the toxic effects of two hair dyes, Basic Red 51 (BR51) and Basic Brown 17 (BB17), which are temporary dyes of the azo group (R-N=N-R'), used in the composition of the black hair dye. To this end, MTT and trypan blue assays (cytotoxicity), comet and micronucleus assay (genotoxicity) were applied, with HepG2 cells. For cytotoxic assessment, dyes were tested in serial dilutions, being the highest concentrations those used in the commercial formula for hair dyes. For genotoxic assessment concentrations were selected according to cell viability. Results showed that both dyes induced significant cytotoxic and genotoxic effects in the cells, in concentrations much lower than those used in the commercial formula. Genotoxic effects could be related to the azo structure present in the composition of the dyes, which is known as mutagenic and carcinogenic. These results point to the hazard of the hair dye exposure to human health.

Potent mutagenicity in the Ames test of 2-cyano-4-nitroaniline and 2,6-dicyano-4-nitroaniline, components of disperse dyes

Genotoxicity data on commercial azo dyes and their components remain sparse, despite their widespread use. We have tested the mutagenicity of 2-cyano-4-nitroaniline (CNNA) and 2,6-dicyano-4-nitroaniline (CNCNNA), components of azo dyes such as Disperse Blue 165 and Disperse Red 73, in Ames test strains. Both compounds are extraordinarily potent frameshift mutagens, with much greater activity than structurally similar dihalonitroanilines and halodinitroanilines. Analysis of the responses of strains over-expressing or deficient in bioactivation enzymes shows that bacterial nitroreductase and acetyl CoA: arylamine N-acetyltransferase are important mediators of the mutagenicity of CNNA and CNCNNA. Environ. Mol. Mutagen., 2015. © 2015 Wiley Periodicals, Inc.

Decolorization of textile dyes by cyanobacteria

Cyanobacteria are widely distributed in the environment and may be an effective and economic alternative for removing dyes from textile industry effluents. The present work investigated the potential of six cyanobacterial strains in decolorizing eleven types of textile dyes. The maximum absorbance of each dye was verified using a spectrophotometer. Mass spectrometry was used to verify the removal and possible degradation of dyes by the cyanobacteria. The results showed that all of the evaluated cyanobacteria were able to remove indigo, palanil yellow, indanthrene yellow, indanthrene blue, dispersol blue, indanthrene red and dispersol red by more than 50%. The Brazilian isolate Phormidium sp. CENA135 was able to decolorize and completely remove indigo blue BANN 30. This study confirmed the capacity of cyanobacteria to decolorize and possibly to structurally degrade different textile dyes, suggesting the possibility of their application in bioremediation studies.

Introducing education for sustainable development in the undergraduate laboratory: quantitative analysis of bioethanol fuel and its blends with gasoline by using solvatochromic dyes

The concept of Education for Sustainable Development, ESD, has been introduced in a period where chemistry education is undergoing a major change, both in emphasis and methods of teaching. Studying an everyday problem, with an important socio-economic impact in the laboratory is a part of this approach. Presently, the students in many countries go to school in vehicles that run, at least partially, on biofuels; it is high time to let them test these fuels. The use of renewable fuels is not new: since 1931 the gasoline sold in Brazil contains 20 to 25 vol-% of bioethanol; this composition is being continually monitored. With ESD in mind, we have employed a constructivist approach in an undergraduate course, where UV-vis spectroscopy has been employed for the determination of the composition of two fuel blends, namely, bioethanol/water, and bioethanol/gasoline. The activities started by giving a three-part quiz. The first and second ones introduced the students to historical and practical aspects of the theme (biofuels). In the third part, we asked them to develop a UV-vis experiment for the determination of the composition of fuel blends. They have tested two approaches: (i) use of a solvatochromic dye, followed by determination of fuel composition from plots of the empirical fuel polarity versus its composition; (ii) use of an ethanol-soluble dye, followed by determination of the blend composition from a Beer's law plot; the former proved to be much more convenient. Their evaluation of the experiment was highly positive, because of the relevance of the problem; the (constructivist) approach employed, and the bright colors that the solvatochromic dye acquire in these fuel blends. Thus ESD can be fruitfully employed in order to motivate the students; make the laboratory "fun", and teach them theory (solvation). The experiments reported here can also be given to undergraduate students whose major is not chemistry (engineering, pharmacy, biology, etc.). They are low-cost and safe to be introduced at high-school level.

Sensitive and fast determination of Sudan dyes in chilli powder by partial-filling micellar electrokinetic chromatography-tandem mass spectrometry

A fast and sensitive method for the simultaneous determination of Sudan dyes (I, II, III, and IV) in food samples was developed for the first time using partial filling micellar electrokinectic chromatography-mass spectrometry (MEKC-MS). The use of MEKC was essential to achieve the separation of these neutral analytes, while the partial filling technique was necessary to avoid the contamination of the ion source with non-volatile micelles. MEKC separation and MS detection conditions were optimized in order to achieve a fast, efficient, and sensitive separation of the four dyes. Filling 25% of the capillary with an MEKC solution containing 40 mM ammonium bicarbonate, 25 mM SDS, and 32.5% (v/v) acetonitrile, a baseline separation of the four azo-dyes was obtained in 10 min. Tandem MS was investigated in order to improve the sensitivity and selectivity of the analysis. Limits of detection (LOD) values 5, 8, 15, and 29 times better were obtained for Sudan III, I, II, and IV, respectively, using partial filling MEKC-MS/MS instead of partial filling MEKC-MS. Under optimized conditions, LOD from 0.05 to 0.2 mu g/mL were obtained. The suitability of the developed method was demonstrated through the fast and sensitive determination of Sudan I, II, III, and IV in spiked chilli powder samples. This determination could not be achieved by MEKC-UV due to the existence of several interfering compounds from the matrix.

Emission features of microstructures fabricated by two-photon polymerization containing three organic dyes

Fabrication of microstructures containing active compounds, such as fluorescent dyes and nanoparticles have been exploited in the last few years, aiming at applications from photonics to biology. Here we fabricate, using two-photon polymerization, microstructures containing the fluorescent dyes Stilbene 420, Disodium Fluorescein and Rhodamine B. The produced microstructures, containing dyes at specific sites, present good structural integrity and a broad fluorescence spectrum, from about 350 nm until 700 nm. Such spectrum can be tuned by using different excitation wavelengths and selecting the excitation position in the microstructure. These results are interesting for designing multi-doped structures, presenting tunable and broad fluorescence spectrum. (C)2012 Optical Society of America

HEPATOTOXICITY ASSESSMENT OF THE AZO DYES DISPERSE ORANGE 1 (DO1), DISPERSE RED 1 (DR1,) AND DISPERSE RED 13 (DR13) IN HEPG2 CELLS

During the dyeing process in baths approximately 10 to 15% of the dyes used are lost and reach industrial effluents, thus polluting the environment. Studies showed that some classes of dyes, mainly azo dyes and their by-products, exert adverse effects on humans and local biota, since the wastewater treatment systems and water treatment plants were found to be ineffective in removing the color and reducing toxicity of some dyes. In the present study, the toxicity of the azo dyes disperse orange 1 (DO1), disperse red 1 (DR1), and disperse red 13 (DR13) was evaluated in HepG2 cells grown in monolayers or in three dimensional (3D) culture. Hepatotoxicity of the dyes was measured using 3-(4,5-dimethylthiazol-2yl)2,5-diphenyltetrazolium (MTT) and cell counting kit 8 (CCK-8) assays after 24, 48, and 72 h of incubation of cells with 3 different concentrations of the azo dyes. The dye DO1 only reduced the mitochondrial activity in HepG2 cells grown in a monolayer after 72 h incubation, while the dye DR1 showed this deleterious effect in both monolayer and 3D culture. In contrast, dye DR13 decreased the mitochondrial activity after 24, 48, and 72 h of exposure in both monolayer and 3D culture. With respect to dehydrogenase activity, only the dye DR13 diminished the activity of this enzyme after 72 h of exposure in both monolayer and 3D culture. Our results clearly demonstrated that exposure to the studied dyes induced cytotoxicity in HepG2 cells.

Photophysical properties and interactions of xanthene dyes in aqueous micelles

Photosensitizers (PS) photodynamic activities are regulated by their location in the biological target, which modulates their photophysical and photochemical features. In this work the PS partition for the Xanthene Dyes Fluorescein (FSC), Eosin Y(EOS), Erythrosin B (ERY) and Rose Bengal B (RBB) in biomimetic models (SDS, CTAB and Pluronic P-123 micelles) and the effects on their photophysical characteristics are evaluated. The hydrophobic and electrostatic forces that govern the PS-micelle interaction are analyzed. At physiological pH (7.25), the ability of the dianionic protolytic form of the dyes to be positioned into the micelle palisade and its micelle interaction depends not only on the hydrophobicity of the dye but also on the micellar surface charge. The Binding Constants obey exactly the same order of the Partition Coefficients for the dyes in P-123 and CTAB micelles. The Stern-Volmer treatment pointed out that dyes are located inside the micelle, especially ERY and RBB. The magnitude of the dye-micelle interaction increased from SDS, P-123 and finally CTAB micelles due to the charges between dye and micelle, and among the xanthenes, their hydrophobic characteristics. Within the micelle pseudo phase, ERY and RBB are still very efficient photosensitizers exhibiting high quantum yield of singlet oxygen, which turns them very attractive especially with P-123 polymeric system as drug delivery systems in photodynamic therapy. (C) 2012 Elsevier B.V. All rights reserved.

Design, synthesis and application of ultrastable rylene dyes for fluorescent labeling of biomolecules

Studies of organic fluorescent dyes are experiencing a renaissance related to the increasing demands posed by new microscopy techniques for high resolution and high sensitivity. While in the last decade single molecule equipment and methodology has significantly advanced and in some cases reached theoretical limits (e.g. detectors approaching unity quantum yields) unstable emission from chromophores and photobleaching become more and more the bottleneck of the advancement and spreading of single-molecule fluorescence studies. The main goal of this work was the synthesis of fluorophores that are water-soluble, highly fluorescent in an aqueous environment, have a reactive group for attachment to a biomolecule and posses exceptional photostability. An approach towards highly fluorescent, water-soluble and monofunctional perylene-3,4,9,10-tetracarboxdiimide and terrylene-3,4:11,12-tetra carboxidiimide chromophores was presented. A new synthetic strategy for the desymmetrization of perylenetetracarboximides was elaborated; water-solubility was accomplished by introducing sulfonyl substituents in the phenoxy ring. Two strategies have been followed relying on either non-specific or site specific labeling. For this purpose a series of new water-soluble monofunctional perylene and terrylene dyes, bearing amine or carboxy group were prepared. The reactivity and photophysical properties of these new chromophores were studied in aqueous medium. The most suitable chromophores were further derivatized with amine or thiol reactive groups, suitable for chemical modification of proteins. The performance of the new fluorescent probes was assessed by single molecule enzyme tracking, in this case phospholipase acting on phospholipid supported layers. Phospholipase-1 (PLA-1) was labeled with N-hydroxysuccinimide ester functionalized perylene and terrylene derivatives. The purification of the conjugates was accomplished by novel convenient procedure for the removal of unreacted dye from labeled enzymes, which involves capturing excess dye with a solid support. This novel strategy for purification of bioconjugates allows convenient and fast separation of labeled proteins without the need for performing time consuming chromatographic or electrophoretic purification steps. The outstanding photostability of the dyes and, associated therewith, the extended survival times under strong illumination conditions allow a complete characterization of enzyme action on its natural substrates and even connecting enzyme mobility to catalytic activity. For site-specific attachment of the rylene dyes to proteins the chromophores were functionalized with thioesters or nitrilotriacetic acid groups. This allowed attachment of the emitters to the N-terminus of proteins by native chemical ligation or complexation with His-tagged polypeptides at the N- or C-termini, respectively. The synthesis of a water-soluble perylenebis (dicarboximide) functionalized with a thioester group was presented. This chromophore exhibits an exceptional photostability and a functional unit for site-specific labeling of proteins. The suitability of the fluorophore as a covalent label was demonstrated via native chemical ligation with protein containing N-terminal cystein residue. We exploited also oligohisitidine sequences as recognition elements for site-selective labeling. The synthesis of a new water-soluble perylene chromophore, containing a nitrilotriacetic acid functional group was demonstrated, using solution-phase and solid-phase approaches. This chromophore combines the exceptional photophysical properties of the rylene dyes and a recognition unit for site-specific labeling of proteins. An important feature of the label is the unchanged emission of the dye upon complexation with nickel ions.

Enzyme tRNA interaction and (t)RNA conformation probed via environmentally sensitive cyanine dyes

Nukleosidmodifikationen beeinflussen Dynamik und Konformation von RNArnund sind epigenetisch wirksam. Wenig verstanden sind konformationelle Dynamik und enzymatische Erkennung von tRNA, sowie der Einfluss des mutmaßlichen kovalenten Inhibitors 5-Fluorouridine (5FU) auf Y Synthasen, die Pseudouridin (Y) erzeugen. Frühere Arbeiten nutzten mit den Fluorophoren Cy3 und Cy5rnmarkierte tRNA, um diese Fragen zu adressieren.rnDie vorliegende Arbeit weitet Cy3-Cy5-Markierung auf Hefe tRNArnPhernaus undrnnutzt Thermophorese und fortschrittliche Fluoreszenzspektroskopie. In der Thermophorese zeigte sich eine hohe Toleranz gegenüber Fluoreszenzmarkierung beirngleichzeitiger Erhöhung der Cy5 Fluoreszenz durch Enzymbindung. Zudem konnte die Konformation verschiedener Mutanten human mitochondrialer tRNArnLysrnund die Bindung von SAM durch SAM-I Riboswitch RNA untersucht werden.rnUm etwaige Unterschiede in der Interaktion von Y55 Synthase TruB mit Cy5-gelabelter U55- bzw. 5FU55-tRNA aufzudecken, wurde eine Kombination ausrnThermophorese, zeit- und polarisationsaufgelöster Fluoreszenzspektroskopie undrn’gel shift’ Experimenten genutzt. Alle Ergebnisse zeigten übereinstimmend einernreversible Bindung ähnlicher Affinität für beide tRNAs und widersprechen somit einer kovalenten Inhibition durch 5FU. Folgerichtig wurde der SDS-stabilernKomplex von TruB mit 5FU-tRNA neu evaluiert, da er bisher als kovalent interpretiert wurde. Es erfolgte eine schnelle Komplexbildung in hoher Ausbeute auchrnfür schlechte Substrate, außerdem ließ sich die Komplexausbeute nicht durch andere Reaktionsbedingungen beeinflussen. Somit kann der SDS stabile Komplexrnnur den ersten, nicht-kovalenten Kontakt von Enzym und 5FU55-tRNA darstellen und repräsentiert kein kovalentes Addukt späterer Katalyse.