Surface characterization of feldspathic ceramic using ATR FT-IR and ellipsometry after various silanization protocols

Objectives. This study characterized the feldspathic ceramic surfaces after various silanization protocols.Methods. Ceramic bars (2 mm x 4 mm x 10 mm) (N = 18) of feldpathic ceramic (VM7, VITA Zahnfabrik) were manufactured and finished. Before silane application, the specimens were ultrasonically cleaned in distilled water for 10 min. The ceramic specimens were randomly divided into nine groups (N = 2 per group) and were treated with different silane protocols. MPS silane (ESPE-Sil, 3M ESPE) was applied to all specimens and left to react at 20 degrees C for 2 min (G20). After drying, the specimens were subjected to heat treatment in an oven at 38 degrees C (G38), 79 degrees C (G79) or 100 degrees C (G100) for 1 min. Half of the specimens of each group were rinsed with water at 80 degrees C for 15 s (G20B, G38B, G79B, G100B). The control group (GC) received no silane. Attenuated total reflection infrared Fourier transform analysis (ATR FT-IR) was performed using a spectrometer. Thickness of silane layer was measured using a spectroscopic ellip-someter working in the lambda = 632.8 nm (He-Ne laser) at 70 degrees incidence angle. Surface roughness was evaluated using an optical profilometer. Specimens were further analyzed under the Scanning Electron Microscopy (SEM) to observe the topographic patterns.Results. ATR FT-IR analysis showed changes in Si-O peaks with enlarged bands around 940 cm(-1). Ellipsometry measurements showed that all post-heat treatment actions reduced the silane film thickness (30.8-33.5 nm) compared to G20 (40 nm). The groups submitted to rinsing in hot water (B groups) showed thinner silane films (9.8-14.4 nm) than those of their corresponding groups (without washing) (30.8-40 nm). Profilometer analysis showed that heat treatments (Ra approximate to 0.10-0.19 mu m; Rq approximate to 0.15-0.26 mu m) provided a smoother surface than the control group (Ra approximate to 0.48 mu m; Rq approximate to 0.65 mu m). Similar patterns were also observed in SEM images.Significance. Heat treatment after MPS silane application improved the silane layer network. Rinsing with boiling water eliminated the outmost unreacted regions of the silane yielding to thinner film thicknesses. (C) 2011 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Resistance to compression of weakened roots subjected to different root reconstruction protocols

Objective: This study evaluated, in vitro, the fracture resistance of human non-vital teeth restored with different reconstruction protocols. Material and methods: Forty human anterior roots of similar shape and dimensions were assigned to four groups (n=10), according to the root reconstruction protocol: Group I (control): non-weakened roots with glass fiber post; Group II: roots with composite resin by incremental technique and glass fiber post; Group III: roots with accessory glass fiber posts and glass fiber post; and Group IV: roots with anatomic glass fiber post technique. Following post cementation and core reconstruction, the roots were embedded in chemically activated acrylic resin and submitted to fracture resistance testing, with a compressive load at an angle of 45 degrees in relation to the long axis of the root at a speed of 0.5 mm/min until fracture. All data were statistically analyzed with bilateral Dunnett's test (alpha=0.05). Results: Group I presented higher mean values of fracture resistance when compared with the three experimental groups, which, in turn, presented similar resistance to fracture among each other. None of the techniques of root reconstruction with intraradicular posts improved root strength, and the incremental technique was suggested as being the most recommendable, since the type of fracture that occurred allowed the remaining dental structure to be repaired. Conclusion: The results of this in vitro study suggest that the healthy remaining radicular dentin is more important to increase fracture resistance than the root reconstruction protocol.

Medium-term protocols for in vivo evaluation of chemical modifiers of carcinogenesis

Cancer development is a long-term multistep process which allows interventional measure before the clincial disease emerges. the detection of natural substances which can block the process of carcinogenesis is a important as the identification of anti-tumoral drugs since they might be used in chemoprevention of cancer in high-risk groups. In vivo rodent models of chemical caecinogenesis have been used to study plant-derived inhibitors of carcinofenesis such as indols, coumarins, isothiocyanates, flavones, phenols and allyl-sulfides. Since the standard in vivo rodent bioassay is prolonged and expensive, shorter reliable protocols are needed. Two in vivo medium-term protocols for evaluation of modifiers of carcinogenesis are presented, one related to liver and the other to bladder cancer. Both protocols use rats, last 8 and 36 weeks and are based on the two-step concept of carcinogenesis: initiation and promotion. The protocols use respectively the development of altered foci of hepatocytes expressing immunochistochemically the placental form of gluthation S-transferase and the appearence of pre-neoplastic urothelium and papillomas as the end-points. the use of these protocols for detection of plantpderived inhibitors of carcinogenesis appear warranted.

Evaluation of different immunization protocols with P. brasiliensis antigens in Guinea pigs

O objetivo deste trabalho foi desenvolver protocolo eficiente e reprodutível de imunização em cobaias com antígenos de P. brasiliensis, visando a obtenção de modelo experimental para futuros estudos de mecanismos de proteção imunológica. Testaram-se três diferentes antígenos (particulado, solúvel e composto) e seis protocolos nos quais foram avaliadas as influências dos seguintes fatores: presença ou ausência de adjuvante completo de Freund, número de doses imunizantes e intervalo de tempo entre a última dose imunizante e o desafio. A eficiência do protocolo de imunização foi estudada pela avaliação da resposta imune celular e humoral anti-P. brasiliensis, utilizando teste cutâneo e teste de inibição da migração do macrófago, e imunodifusão, respectivamente. Observou-se que: 1. Três doses imunizantes de antígeno induziram melhor resposta do que duas doses; 2. Maior resposta imune foi conseguida com a utilização de adjuvante completo de Freund; 3. Animais desafiados depois de longo tempo (6 semanas) da última dose imunizante mostraram melhor resposta imune anti-P. brasiliensis; 4. Os antígenos solúvel e composto foram igualmente eficientes induzindo maior resposta imune humoral e celular anti-P. brasiliensis enquanto que o antígeno particulado provocou menor reatividade

Protocols for hyperlactatemia induction in the lactate minimum test adapted to swimming rats

The lactate minimum test (LACmin) has been considered an important indicator of endurance exercise capacity and a single session protocol can predict the maximal steady state lactate (MLSS). The objective of this study was to determine the best swimming protocol to induce hyperlactatemia in order to assure the LACmin in rats (Rattus norvegicus), standardized to four different protocols (P) of lactate elevation. The protocols were PI: 6 min of intermittent jumping exercise in water (load of 50% of the body weight - bw); P2: two 13% bw load swimming bouts until exhaustion (thin); P3: one thin 13% bw load swimming bout; and P4: two 13% bw load swimming bouts (1st 30 s, 2nd to thin), separated by a 30 s interval. The incremental phase of LACmin beginning with initial loads of 4% bw, increased in 0.5% at each 5 min. Peak lactate concentration was collected after 5, 7 and 9 min (mmol L-1) and differed among the protocols P 1 (15.2 +/- 0.4, 14.9 +/- 0.7, 14.8 +/- 0.6) and P2 (14.0 +/- 0.4, 14.9 +/- 0.4, 15.5 +/- 0.5) compared to P3 (5.1 +/- 0.1, 5.6 +/- 0.3, 5.6 +/- 0.3) and P4 (4.7 +/- 0.2, 6.8 +/- 0.2, 7.1 +/- 0.2). The LACmin determination success rates were 58%, 55%, 80% and 91% in P1, P2, P3 and P4 protocols, respectively. The MLSS did not differ from LACmin in any protocol. The LACmin obtained from P4 protocol showed better assurance for the MLSS identification in most of the tested rats. (c) 2007 Elsevier B.V. All rights reserved.

Effect of various acupuncture treatment protocols upon sepsis in wistar rats

Sepsis is a syndrome characterized by infection and generalized inflammatory response that can lead to organ failure and death. In this study we standardize a model to investigate acupuncture's effects upon sepsis. The objectives were to study the use of acupuncture in the infectious process and to formulate acupuncture's treatment protocol for sepsis. The CLP (cecal ligation and puncture) model in rats was used to induce sepsis through bacterial entrance into the peritoneal cavity. An acupuncture treatment protocol that enhanced survival and reversed the neutrophil impairment migration toward the peritoneal cavity in rats with sepsis was achieved. It seems that acupuncture can be used for the treatment of experimental infectious processes. The effects of acupuncture and related mechanisms are discussed.

A revised taxonomy for time warp based distributed synchronization protocols

This paper presents an improved and updated taxonomy for Time Warp based distributed synchronization protocols. This taxonomy aims to allow the grouping of several optmistic distributed simulation synchronization protocols, with the objective to facilitate the task to decide which protocol is better for a specific simulation.

Ovarian follicle diameter at timed insemination and estrous response influence likelihood of ovulation and pregnancy after estrous synchronization with progesterone or progestin-based protocols in suckled Bos indicus cows

The objectives of the present study were to evaluate factors associated with estrous synchronization responses and pregnancy per insemination (P/AI) in Bos indicus beef cows submitted to progesterone-based fixed-time artificial insemination (FTAI) protocols. A total of 2388 cows (1869 Nellore and 519 crossbred Nellore x Angus) from 10 commercial farms were evaluated to determine the relationships among breed, body condition score (BCS) on the first day of the FTAI protocol, the occurrence of estrus between progesterone device removal and FTAI and diameter of largest ovarian follicle (LF) at FTAI on estrous synchronization responses and P/AI. Cows (n=412 primiparous; 1976 multiparous) received an intravaginal device containing progesterone or an ear implant containing norgestomet (a progestin), and an injection of estradiol at the beginning of the estrous synchronization protocol. Body condition was scored using a 1-5 scale on the first day of the FTAI protocol and at 30-60 days postpartum. Females received 300IU of equine chorionic gonadotropin (eCG) and PGF(2 alpha) on the day the progesterone device/implant was removed and were inseminated 48-60h later. At insemination, cows (n=2388) were submitted to an ultrasonographic exam to determine the diameter of the LF. Follicles were classified into four categories based on mean and standard deviation (SD) of the LF (LF1 = two SD below the mean; LF2 = mean minus one SD; LF3 = mean plus one SD; LF4 = two SD above the mean). Ovulation rate was determined in a subset of cows (n=813) by three consecutive ultrasonographic exams: (1) at time of progesterone device/implant removal, (2) at time of FTAI and (3) 48 h after FTAI. Ovulation was defined as the disappearance of a large follicle (>= 8.0 mm) that was previously recorded. Estrus was determined in a subset of the cows (n = 445) by the activation of a detection of estrous patch placed on the tail head on the day of progesterone device/implant removal. Pregnancy was diagnosed 30 days after FTAI. Pregnancy was influenced (P = 0.001) by follicle diameter [LF1 = 27.5% (81/295), LF2 = 46.6% (328/705), LF3 = 57.9% (647/1118), LF4 = 63.3% (171/270)] and the occurrence of estrus [estrus = 67.7% (174/257) and no estrus = 36.2% (68/188)]. Follicle diameter at FTAI influenced ovulation rate [LF1 = 42.5% (34/80), LF2 = 73.9% (161/218), LF3 = 95.8% (407/425), LF4 = 97.8% (88/90)], the occurrence of estrus [LF1 = 54.8% (51/93), LF2 = 33.6% (43/128), LF3 = 68.9% (126/183), LF4 = 90.2% (37/41)] and P/AI among cows that had ovulations [LF1 =32.4% (11/34), LF2 = 50.3% (81/161), LF3 = 60.0% (244/407), LF4 = 68.2% (60/88)]. Improving estrous responses between progesterone device withdrawal and FTAI and increasing the diameter of the LF at FTAI may be important aspects to achieve improved estrous synchronization responses and P/AI following progesterone/progestin and estradiol based FTAI protocols in suckled Bos indicus cows. (C) 2010 Elsevier B.V. All rights reserved.

LH and FSH concentration and follicular development in Nellore heifers submitted to fixed-time artificial insemination protocols with different progesterone concentrations

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Dynamic and isometric protocols of knee extension: Effect of fatigue on the EMG signal

The objective of this study was to analyze the electromyographic (EMG) signal behavior of rectus femoris (RF), vastus medialis (VM), vastus lateralis (VL) and biceps femoris (caput longum) (BFCL) from nine women during fatiguing dynamic and isometric knee extensions tests and to determine their EMGFT (Electromyographic Fatigue Threshold). Surface electrodes, biological signal acquisition module, analogical-digital converter board and specific software were used. The RMS (Root Mean Square) values obtained from concentric phase (80 to 30 degrees) of the dynamic knee extension andfrom isometric contraction were correlated with time on each load by linear regression analysis. The respective slopes were correlated with the correspondent load to determine the EMGFT. Force (Kgf) and median frequency - MF (Hz) obtained during MIVC (Maximal Isometric Voluntary Contraction) performed before and after the fatiguing tests were calculated in Matlab environment. The results demonstrated that the endurance time decreases with higher loads the EMG amplitude increase with time and was greater at higher loads, between muscles in dynamic exercise the RF and VL showed higher slopes, and in isometric exercise the VL showed the same behavior The EMGFT values were similar in both exercises; the force values predominantly decreased after fatiguing tests; however the MF only decreased after some loads. The protocols proposed allowed standardizing protocols at least to induce the fatigue process and to determine the EMGFT as an endurance indicative, which may be used to evaluate the effectiveness of rehabilitative or training interventions indicated to reduce muscle weakness and fatigue.