A 75-81 GHz, 14.3 dBm Peak Output Power, 21 dB Peak Gain, SiGe Power-Combining Amplifier Operating from a Single 3.3 V Supply

A compact differential 4-way power combiner with 2.3 dB loss and high common-mode rejection characteristic for use in mm-wave PAs is presented. A complete circuit comprised of a power splitter, two-stage cascode PA array, and a power combiner was implemented in SiGe technology. Measured small-signal gain of at least 17 dB was obtained from 74.5 GHz to 80.5 GHz with a peak 21 dB at 79 GHz. The prototype delivered 13.2 dBm P1dB and 14.3 dBm Psat when operated from a single 3.3 V supply at 75 GHz.

Electrical characterization of metal-oxide-polymer devices for non-volatile memory applications

The objective of this thesis is to study the properties of resistive switching effect based on bistable resistive memory which is fabricated in the form of Al2O3/polymer diodes and to contribute to the elucidation of resistive switching mechanisms. Resistive memories were characterized using a variety of electrical techniques, including current-voltage measurements, small-signal impedance, and electrical noise based techniques. All the measurements were carried out over a large temperature range. Fast voltage ramps were used to elucidate the dynamic response of the memory to rapid varying electric fields. The temperature dependence of the current provided insight into the role of trapped charges in resistive switching. The analysis of fast current fluctuations using electric noise techniques contributed to the elucidation of the kinetics involved in filament formation/rupture, the filament size and correspondent current capabilities. The results reported in this thesis provide insight into a number of issues namely: (i) The fundamental limitations on the speed of operation of a bi-layer resistive memory are the time and voltage dependences of the switch-on mechanism. (ii) The results explain the wide spread in switching times reported in the literature and the apparently anomalous behaviour of the high conductance state namely the disappearance of the negative differential resistance region at high voltage scan rates which is commonly attributed to a “dead time” phenomenon which had remained elusive since it was first reported in the ‘60s. (iii) Assuming that the current is filamentary, Comsol simulations were performed and used to explain the observed dynamic properties of the current-voltage characteristics. Furthermore, the simulations suggest that filaments can interact with each other. (iv) The current-voltage characteristics have been studied as a function of temperature. The findings indicate that creation and annihilation of filaments is controlled by filling and neutralizing traps localized at the oxide/polymer interface. (v) Resistive switching was also studied in small-molecule OLEDs. It was shown that the degradation that leads to a loss of light output during operation is caused by the presence of a resistive switching layer. A diagnostic tool that predicts premature failure of OLEDs was devised and proposed. Resistive switching is a property of oxides. These layers can grow in a number of devices including, organic light emitting diodes (OLEDs), spin-valve transistors and photovoltaic devices fabricated in different types of material. Under strong electric fields the oxides can undergo dielectric breakdown and become resistive switching layers. Resistive switching strongly modifies the charge injection causing a number of deleterious effects and eventually device failure. In this respect the findings in this thesis are relevant to understand reliability issues in devices across a very broad field.

Systèmes vésiculaires colloïdaux pour la vectorisation de la 1-β-D-arabinofuranosylcytosine

La 1-β-D-arabinofuranosylcytosine (ara-C) demeure l’agent anticancéreux principalement utilisé dans le traitement de la leucémie myéloblastique aiguë (LMA), malgré sa dégradation et son élimination rapide après une administration parentérale. Son encapsulation dans des vecteurs pharmaceutiques, majoritairement des liposomes, a permis de surmonter ces inconvénients. L’objectif général de ce projet de doctorat était de développer deux systèmes à libération prolongée, à base de phospholipides, de cholestérol et de poly(éthylène glycol) (PEG) afin d’encapsuler l’ara-C et ultimement, d’améliorer son efficacité dans le traitement de la LMA. Des Sphérulites® (vésicules multilamellaires d’un type particulier) ont d’abord été étudiées pour leur forte capacité d’encapsulation, due à leur mode de préparation. Par la suite, une formulation liposomale capable, d’une part de cibler spécifiquement les cellules leucémiques et, d’autre part, de promouvoir la libération intracellulaire de l’ara-C grâce à sa sensibilité au pH, a été mise au point. Les deux formulations se devaient d’avoir un faible diamètre, une stabilité en présence de fluides biologiques et des temps de circulation prolongés chez l’animal. Une préparation de Sphérulites®, composée de Phospholipon 90G, de Solutol HS15 et de cholestérol, a permis d’obtenir des vésicules de 300 nm de diamètre. Un dérivé lipidique de PEG a pu être fixé à leur surface, sans modifier la disposition concentrique des lamelles, ni changer leur stabilité. Les Sphérulites® PEGylées ont été chargées d’ara-C et injectées chez le rat par la voie intraveineuse. Elles ont démontré des temps de circulation significativement prolongés comparativement aux Sphérulites® sans PEG. Cependant, l’ara-C s’est retrouvée éliminée de la circulation sanguine très rapidement, révélant une libération précoce du principe actif à partir de ces vésicules. Les liposomes sensibles au pH (~150 nm) ont été obtenus suite à l’insertion d’un copolymère à base de dioctadécyle, de N-isopropylacrylamide (NIPAM) et d’acide méthacrylique. L’anticorps anti-CD33, soit complet soit son fragment Fab’, a été fixé à la surface des liposomes afin de cibler les cellules leucémiques. Les essais in vitro ont démontré la spécificité de la formulation pour différentes cellules leucémiques (CD33+), sa stabilité en présence de protéines plasmatiques et la libération intracellulaire d’un marqueur fluorescent et de l’ara-C. Enfin, des études menées chez la souris saine et immunodéprimée inoculée de cellules HL60 ont montré que la formulation exposant le fragment Fab’ possédait un profil pharmacocinétique et une biodistribution semblables à ceux des liposomes contrôles non-ciblés. L’encapsulation de l’ara-C a permis d’améliorer grandement ses temps de circulation après une administration intraveineuse. Cependant, bien que les immunoliposomes ont permis de prolonger la survie des souris leucémiques comparativement à l’ara-C libre, l’addition du polymère sensible au pH n’a pas permis d’apporter de réel avantage à la formulation lorsque administrée in vivo. Les résultats obtenus dans ce travail de thèse ont, dans un premier temps, mis en évidence que les Sphérulites® pourraient s’avérer utiles dans la vectorisation d’agents anticancéreux si leur capacité à retenir le principe actif in vivo était améliorée. Dans un second temps, les données présentées avec les immunoliposomes suggèrent qu’ils pourraient apporter un bénéfice notable dans le traitement de la LMA.

Amplifying vibrational circular dichroism by manipulation of the electronic manifold

Vibrational circular dichroism is a powerful technique to study the stereochemistry of chiral molecules, but often suffers from small signal intensities. Electrochemical modulation of the energies of the electronically excited state manifold is now demonstrated to lead to an order of magnitude enhancement of the differential absorption. Quantum-chemical calculations show that increased mixing between ground and excited states is at the origin of this amplification.

Attribution of climate extreme events

There is a tremendous desire to attribute causes to weather and climate events that is often challenging from a physical standpoint. Headlines attributing an event solely to either human-induced climate change or natural variability can be misleading when both are invariably in play. The conventional attribution framework struggles with dynamically driven extremes because of the small signal-to-noise ratios and often uncertain nature of the forced changes. Here, we suggest that a different framing is desirable, which asks why such extremes unfold the way they do. Specifically, we suggest that it is more useful to regard the extreme circulation regime or weather event as being largely unaffected by climate change, and question whether known changes in the climate system's thermodynamic state affected the impact of the particular event. Some examples briefly illustrated include 'snowmaggedon' in February 2010, superstorm Sandy in October 2012 and supertyphoon Haiyan in November 2013, and, in more detail, the Boulder floods of September 2013, all of which were influenced by high sea surface temperatures that had a discernible human component.

MRI study of radiation effect on Fricke gel solutions

The quality control optimization of medical processes that use ionizing radiation in the treatment of diseases like cancer is a key element for patient safety and success of treatment. The major medical application of radiation is radiotherapy, i.e. the delivery of dose levels to well-defined target tissues of a patient with the purpose of eliminating a disease. The need of an accurate tumour-edge definition with the purpose of preserving healthy surrounding tissue demands rigorous radiation treatment planning. Dosimetric methods are used for dose distribution mapping region of interest to assure that the prescribed dose and the irradiated region are correct. The Fricke gel (FXG) is the main dosimeter that supplies visualization of the three-dimensional (3D) dose distribution. In this work the dosimetric characteristics of the modified Fricke dosimeter produced at the Radiation Metrology Centre of the Institute of Energetic and Nuclear Research (IPEN) such as gel concentration dose response dependence, xylenol orange addition influence, dose response between 5 and 50Gy and signal stability were evaluated by magnetic resonance imaging (MRI). Using the same gel solution, breast simulators (phantoms) were shaped and absorbed dose distributions were imaged by MRI at the Nuclear Resonance Laboratory of the Physics Institute of Sao Paulo University. (C) 2007 Elsevier Ltd. All rights reserved.

Synthesis and electrical characterization of CaBi2Nb2O9 thin films deposited on Pt/Ti/SiO2/Si substrates by polymeric precursor method

We report the successful deposition of CaBi2Nb2O9 (CBN) thin films on platinum coated silicon substrates by polymeric precursor method. The CBN thin films exhibited good structural, dielectric and CBN/Pt interface characteristics. The leakage current of the capacitor structure was around 0.15 A cm(-2) at an applied electric field of 30 kV cm(-1). The capacitance-voltage measurements indicated good ferroelectric polarization switching characteristics. The typical measured small signal dielectric constant and the dissipation factor at a frequency of 100 kHz were 90 and 0.053, respectively. The remanent polarization and the drive voltage values were 4.2 C cm(-2) and 1.7 V at an applied voltage of 10 V. No significant fatigue was observed at least up to 10(8) switching cycles. (c) 2005 Elsevier B.V. All rights reserved.

Synthesis, ferroelectric and optical properties of (Pb,Ca)TiO3 thin films by soft solution processing

Calcium modified lead titanate sol was synthesized using a soft solution processing, the so-called polymeric precursor method. In soft chemistry method, soluble precursors such as lead acetate trihydrate, calcium carbonate and titanium isopropoxide, as starting materials, were mixed in aqueous solution. Pb0.7Ca0.3TiO3 thin films were deposited on platinum-coated silicon and quartz substrates by means of the spinning technique. The surface morphology and crystal structure, dielectric and optical properties of the thin films were investigated. The electrical measurements were conducted on metal-ferroelectric-metal (MFM) capacitors. The typical measured small signal dielectric constant and dissipation factor at a frequency of 100 kHz were 299 and 0.065, respectively, for a thin film with 230 nm thickness annealed at 600degreesC for 2 h. The remanent polarization (2P(r)) and coercive field (E-c) were 32 muC/cm(2) and 100 kV/cm, respectively. Transmission spectra were recorded and from them, refractive index, extinction coefficient, and band gap energy were calculated. Thin films exhibited good optical transmissivity, and had optical direct transitions. The present study confirms the validity of the DiDomenico model for the interband transition, with a single electronic oscillator at 6.858 eV. The optical dispersion behavior of PCT thin film was found to fit well the Sellmeir dispersion equation. The band gap energy of the thin film, annealed at 600degreesC, was 3.56 eV. The results confirmed that soft solution processing provides an inexpensive and environmentally friendly route for the preparation of PCT thin films.

Properties of BaBi2Ta2O9 thin films prepared by chemical solution deposition technique for dynamic random-access memory applications

We report on the properties of BaBi2Ta2O9 (BBT) thin films for dynamic random-access memory (DRAM) and integrated capacitor applications. Crystalline BBT thin films were successfully fabricated by the chemical solution deposition technique on Pt-coated Si substrates at a low annealing temperature of 650°C. The films were characterized in terms of structural, dielectric, and insulating properties. The electrical measurements were conducted on Pt/BBT/Pt capacitors. The typical measured small signal dielectric constant and dissipation factor, at 100 kHz, were 282 and 0.023, respectively, for films annealed at 700°C for 60 min. The leakage current density of the films was lower than 10-9 A/cm2 at an applied electric field of 300 kV/cm. A large storage density of 38.4 fC/μm2 was obtained at an applied electric field of 200 kV/cm. The high dielectric constant, low dielectric loss and low leakage current density suggest the suitability of BBT thin films as dielectric layer for DRAM and integrated capacitor applications.

Micro-inverter for integrated grid-tie PV module using resonant controller

Two-stage isolated converters for photovoltaic (PV) applications commonly employ a high-frequency transformer on the DC-DC side, submitting the DC-AC inverter switches to high voltages and forcing the use of IGBTs instead of low-voltage and low-loss MOSFETs. This paper shows the modeling, control and simulation of a single-phase full-bridge inverter with high-frequency transformer (HFT) that can be used as part of a two-stage converter with transformerless DC-DC side or as a single-stage converter (simple DC-AC inverter) for grid-connected PV applications. The inverter is modeled in order to obtain a small-signal transfer function used to design the PResonant current control regulator. A high-frequency step-up transformer results in reduced voltage switches and better efficiency compared with converters in which the transformer is used on the DC-DC side. Simulations and experimental results with a 200 W prototype are shown. © 2012 IEEE.

Utilização de sinais adicionais estabilizantes para o amortecimento de oscilações de baixa frequência do sistema elétrico de potência multimáquinas

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Preparação e caracterização de filmes finos de 'BA''BI IND.2''TA IND.2''O IND.9(BBT)' e 'BA''BI IND.2''NB IND.2''O IND.9(BBN)'

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Micro-inverter for integrated grid-tie photovoltaic module using resonant controller

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Search for standard model production of four top quarks in the lepton plus jets channel in pp collisions at root S=8 TeV

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Microinversor integrado ao módulo fotovoltaico para sistemas conectados à rede elétrica utilizando controlador ressonante

This paper shows the modeling and control of a single-phase full-bridge inverter with high-frequency transformer that may be used as part of a two-stage converter with transformerless DC-DC side or as a single-stage converter (simple DC-AC converter) for grid-connected PV applications. The inverter is modeled in order to obtain a small-signal transfer function used to design the P+Resonant current controller. A highfrequency step-up transformer results in reduced voltage switches and better efficiency compared with converters in which the transformer is used on the DC-DC side. Simulations and experimental results with a 200 W prototype are shown. 1