Influência da vermiculita expandida na resistência à compressão e reologia de pastas cimentantes de poços de petróleo

Several problems related to the loss of hydraulic seal in oilwells, causing gas migration and/or contamination of the production zone by water, have been reported. The loss of the hydraulic seal is a consequence of cracks which can be occasioned either by the invasion of gas during the wait on cement or by the expansion of the casing causing the fracture of the cement sheath. In case of the pressure of the formation is higher than the pressure in the annulus, gas can migrate into the slurry and form microannulus, which are channels where gas migrates after the cement is set. Cracks can be also occasioned by the fracture of the cement sheath when it does not withstand the thermal and dynamic loads. In reservoirs where the oil is heavy, steam water injection operation is required in order to get the oil flowing. This operation increases the temperature of the casing, and then it expands and causes the fracture of the cement sheath in the annulus. When the failures on the cement are detected, remedial cementing is required, which raise costs caused by the interventions. Once the use of cement in the construction civil sector is older than its use in the petroleum sector, it is common to bring technologies and solutions from the civil construction and apply them on the petroleum area. In this context, vermiculite, a mineral-clay widely encountered in Brazil, has been used, on its exfoliated form, in the civil construction, especially on the manufacture of lights and fireproof concretes with excellent thermal and acoustical properties. It has already been reported in scientific journals, studies of the addition of exfoliated vermiculite in Portland cements revealing good properties related to oilwell cementing operations. Thus, this study aimed to study the rheological behavior, thickening time, stability and compressive strength of the slurries made of Portland cement and exfoliated vermiculite in 5 different compositions, at room temperature and heated. The results showed that the compressive strength decreased with the addition of exfoliated vermiculite, however the values are still allowed for oiwell cementing operations. The thickening time of the slurry with no exfoliated vermiculite was 120 min and the thickening time of the slurry with 12 % of exfoliated vermiculite was 98 min. The stability and the rheological behavior of the slurries revealed that the exfoliated vermiculite absorbed water and therefore increased the viscosity of the slurries, even though increasing the factor cement-water. The stability experiment carried out at 133 ºF showed that, there was neither sedimentation nor reduction of the volume of the cement for the slurry with 12 % of exfoliated vermiculite. Thus, the addition of exfoliated vermiculite accelerates the set time of the cement and gives it a small shrinkage during the wait on cement, which are important to prevent gas migration

Adição de resíduo cerâmico em pastas geopoliméricas para cimentação de poços de petróleo

The development of activities the of oil and gas sector have promoted the search for suitable materials for cementing oil wells. In the state of the Rio Grande do Norte, the integrity of the cement sheath tends to be impaired during steam injection, a procedure necessary to increase oil recovery in reservoirs with low-viscosity oil. The geopolymer is a material that can be used as alternative cement, since it has been used in the production of fire-resistant components, building structures, and for the control of toxic or radioactive residues. Geopolymers result from condensation polymer alkali aluminosilicates and silicates resulting three-dimensional polymeric structures. They are produced in a manner different from that of Portland cement, which is made an activating solution that is mixed with geopolymer precursor. Among the few works studied allowed us to conclude that the pastes prepared with metakaolin as precursor showed better performance of its properties. Several studies show the addition of waste clay as a means of reducing cost and improving end of the folder properties. On this basis, the goal is to study the influence of the addition of ceramic waste in geopolymer paste. To develop the study of rheology tests were carried out, filtered, thickening time, compressive strength, free water, specific gravity and permeability, according to the American Pretoleum Institute (API). The results for all formulations studied show that the folders have high mechanical strength to a light paste; low filtrate volume, absence of free water, very low permeability, slurry, consistent with a light paste, and thickening time low that can be corrected with the use of a retardant handle. For morphological characterization, microstructural, physical, chemical and thermal tests were carried out by XRD, MEV, DTA, TG, FTIR. In the trial of XRD, it was found that geopolymer is an amorphous material, with a peak of crystalline kaolinite. In tests of TG / DTA, revealed the presence of a significant event, which represents the mass loss related to water, and also observed the reduction of weight loss by increasing the concentration of ceramic waste. In the trial of MEV, we found a uniform matrix without the presence of other phases. In the trial of FT-IR, we observed the presence of the band related to water. From all results it was determined that the optimum concentration range of use is between 2.5 and 5% of waste ceramic

Aditivação de pastas geopoliméricas com tetraborato de sódio e látex não iônico para cimentação de Poços de Petróleo

The development of activities in the oil and gas sector has been promoting the search for materials more adequate to oilwell cementing operation. In the state of Rio Grande do Norte, the cement sheath integrity tend to fail during steam injection operation which is necessary to increase oil recovery in reservoir with heavy oil. Geopolymer is a material that can be used as alternative cement. It has been used in manufacturing of fireproof compounds, construction of structures and for controlling of toxic or radioactive waste. Latex is widely used in Portland cement slurries and its characteristic is the increase of compressive strength of cement slurries. Sodium Tetraborate is used in dental cement as a retarder. The addition of this additive aim to improve the geopolymeric slurries properties for oilwell cementing operation. The slurries studied are constituted of metakaolinite, potassium silicate, potassium hydroxide, non-ionic latex and sodium tetraborate. The properties evaluated were: viscosity, compressive strength, thickening time, density, fluid loss control, at ambient temperature (27 ºC) and at cement specification temperature. The tests were carried out in accordance to the practical recommendations of the norm API RP 10B. The slurries with sodium tetraborate did not change either their rheological properties or their mechanical properties or their density in relation the slurry with no additive. The increase of the concentration of sodium tetraborate increased the water loss at both temperatures studied. The best result obtained with the addition of sodium tetraborate was thickening time, which was tripled. The addition of latex in the slurries studied diminished their rheological properties and their density, however, at ambient temperature, it increased their compressive strength and it functioned as an accelerator. The increase of latex concentration increased the presence of water and then diminished the density of the slurries and increased the water loss. From the results obtained, it was concluded that sodium tetraborate and non-ionic latex are promising additives for geopolymer slurries to be used in oilwell cementing operation

Aplicação de termogravimetria acoplada à espectrometria de massas para caracterização de petróleo e determinação da curva de evolução de gás sulfídrico

With the new discoveries of oil and gas, the exploration of fields in various geological basins, imports of other oils and the development of alternative fuels, more and more research labs have evaluated and characterized new types of petroleum and derivatives. Therefore the investment in new techniques and equipment in the samples analysis to determine their physical and chemical properties, their composition, possible contaminants, especification of products, among others, have multiplied in last years, so development of techniques for rapid and efficient characterization is extremely important for a better economic recovery of oil. Based on this context, this work has two main objectives. The first one is to characterize the oil by thermogravimetry coupled with mass spectrometry (TG-MS), and correlate these results with from other types of characterizations data previously informed. The second is to use the technique to develop a methodology to obtain the curve of evaluation of hydrogen sulfide gas in oil. Thus, four samples were analyzed by TG-MS, and X-ray fluorescence spectrometry (XRF). TG results can be used to indicate the nature of oil, its tendency in coke formation, temperatures of distillation and cracking, and other features. It was observed in MS evaluations the behavior of oil main compounds with temperature, the points where the volatilized certain fractions and the evaluation gas analysis of sulfide hydrogen that is compared with the evaluation curve obtained by Petrobras with another methodology

Análise do desempenho de um queimador infravermelho funcionando com gás liquefeito de petróleo e glicerina

The use of infrared burners in industrial applications has many advantages in terms of technical-operational, for example, uniformity in the heat supply in the form of radiation and convection, with greater control of emissions due to the passage of exhaust gases through a macro-porous ceramic bed. This paper presents an infrared burner commercial, which was adapted an experimental ejector, capable of promoting a mixture of liquefied petroleum gas (LPG) and glycerin. By varying the percentage of dual-fuel, it was evaluated the performance of the infrared burner by performing an energy balance and atmospheric emissions. It was introduced a temperature controller with thermocouple modulating two-stage (low heat / high heat), using solenoid valves for each fuel. The infrared burner has been tested and tests by varying the amount of glycerin inserted by a gravity feed system. The method of thermodynamic analysis to estimate the load was used an aluminum plate located at the exit of combustion gases and the distribution of temperatures measured by a data acquisition system which recorded real-time measurements of the thermocouples attached. The burner had a stable combustion at levels of 15, 20 and 25% of adding glycerin in mass ratio of LPG gas, increasing the supply of heat to the plate. According to data obtained showed that there was an improvement in the efficiency of the 1st Law of infrared burner with increasing addition of glycerin. The emission levels of greenhouse gases produced by combustion (CO, NOx, SO2 and HC) met the environmental limits set by resolution No. 382/2006 of CONAMA

Proposta de modelo de interação da Universidade Federal do Rio Grande do Norte e empresas do setor de petróleo

Operational procedures may negatively interfere in negotiation and execution regarding universities and business companies. In some cases it may even derail business interaction. Thus, aiming to overcome this and other barriers a university-industry interaction model was structured. The model enhances the appropriation of technological solutions on behalf of enterprises, as well as aim to improve the quality of teaching and research done at the university. In order to conduct a case study, sampling considering the Federal University of Rio Grande do Norte (UFRN) was made as well as the Oil and Gas sector. For data collection questionnaires, classroom observation, document analysis, semi-structured interviews were used. The study describes the companies as well as the internal organization of UFRN in their interaction context. The diagnosis related to past interactions as well as the expectations of the companies and the university s internal subjects regarding the university-industry relationship were also studied. Thus, specific questionnaires were applied for the three types of groups: researchers, managers and business companies. These subjects pointed out that the great deal of barriers they identified were related to issues regarding the university internal management. Given these barriers, the critical factors were then identified in order to overcome this reality. Among the nine critical factors only one belongs to the macro environment, while the remaining factors are related to organizational issues present in the university context. It was possible to formulate a university-business interaction model one the researched focused on the case study results and contribution from a theoretical framework that was enabled trough literature review. The model considers all business collaboration mechanisms; it focuses on a particular strategic productive sector and provides a co-evolution vision over time, according to the sector´s development strategy. The need for institutionalizing the relationship with the companies involved is pointed out. The proposed model considers all the critical factors identified by the research; it aims long-term relationship with the company and integrates teaching, research and extension actions. The model implementation was also considered. It was seen that it must be done in three phases. The phases will be defined by the level of maturity in the relationship between the university and the companies. Thus, a framework was developed in order to assess the interaction level regarding company institutionalization. Whilst structuring the model was a concern with replication came up. It was pointed out that this model should not only serve to this specific case study situation. So the final result is a model of university-industry relationship appropriate in the first instance, for UFRN, but has applicability, in general, to any Brazilian university

Ecogenômica de archaea e monitoramento de comunidades de procariotos redutores de sulfato: aplicações na indústria de petróleo e gás

The human activities responsible for the ambient degradation in the modern world are diverse. The industrial activities are preponderant in the question of the impact consequences for brazilian ecosystems. Amongst the human activities, the petroliferous industry in operation in Potiguar Petroliferous Basin (PPB) displays the constant risk of ambient impacts in the integrant cities, not only for the human populations and the environment, but also it reaches the native microorganisms of Caatinga ground and in the mangrove sediment. Not hindering, the elaboration of strategies of bioremediation for impacted areas pass through the knowledge of microbiota and its relations with the environment. Moreover, in the microorganism groups associated to oil, are emphasized the sulfate-reducing prokaryotes (SRP) that, in its anaerobic metabolism, these organisms participate of the sulfate reduction, discharging H2S, causing ambient risks and causing the corrosion of surfaces, as pipelines and tanks, resulting in damages for the industry. Some ancestries of PRS integrate the Archaea domain, group of microorganisms whose sequenced genomes present predominance of extremophilic adaptations, including surrounding with oil presence. This work has two correlated objectives: i) the detection and monitoring of the gene dsrB, gift in sulfate-reducing prokaryotes, through DGGE analysis in samples of mDNA of a mangrove sediment and semiarid soil, both in the BPP; ii) to relate genomic characteristics to the ecological aspects of Archaea through in silico studies, standing out the importance to the oil and gas industry. The results of the first work suggest that the petrodegraders communities of SRP persist after the contamination with oil in mangrove sediment and in semiarid soil. Comparing the populations of both sites, it reveals that there are variations in the size and composition during one year of experiments. In the second work, functional and structural factors are the probable cause to the pressure in maintenance of the conservation of the sequences in the multiple copies of the 16S rDNA gene. Is verified also the discrepancy established between total content GC and content GC of the same gene. Such results relating ribosomal genes and the ambient factors are important for metagenomic evaluations using PCR-DGGE. The knowledge of microbiota associated to the oil can contribute for a better destination of resources by the petroliferous industry and the development of bioremediation strategies. Likewise, search to lead to the best agreement of the performance of native microbiota in biogeochemical cycles in Potiguar Petroliferous Basin ecosystem

Estudo do efeito da adição de gás condensado sobre o ponto de fluidez e a viscosidade de petróleos pesados

Neste trabalho foi estudado o comportamento de quatro óleos pesados, com densidade API variando de 13,7 a 21,6, frente à adição de gás condensado, com o objetivo de se obter informações relevantes para o processo de escoamento destes óleos. Assim, foi analisado o comportamento da densidade à 20 °C, pontos de fluidez máximo e mínimo, e viscosidade dinâmica à 50 °C dos óleos contendo diferentes concentrações de gás condensado. Também foi analisado o efeito da variação da temperatura sobre a viscosidade dos óleos crus, e, adicionalmente, após o estudo do efeito do gás condensado sobre os óleos, foi avaliado o comportamento da viscosidade dinâmica dos mesmos com a adição de diferentes solventes orgânicos (querosene, aguarrás e tolueno). Os resultados obtidos indicaram que o gás condensado foi eficiente para a redução da densidade, dos pontos de fluidez máximo e mínimo e da viscosidade dos quatros óleos analisados. O óleo A apresentou uma taxa de decaimento da densidade mais baixa do que os outros óleos e foi o que apresentou o comportamento mais próximo de mistura ideal. A amostra de óleo mais pesada (óleo D) foi a que apresentou as maiores variações nos valores dos pontos de fluidez máximo e mínimo com a adição de condensado, chegando a reduzir um total de 19 °C no ponto de fluidez máximo e um total de 21 °C no ponto de fluidez mínimo com a adição de apenas 10,7% v/v de gás condensado. Nos resultados obtidos nas análises da viscosidade dinâmica observou-se que a grande maioria das misturas preparadas apresentou um comportamento de fluido newtoniano. Todas as amostras apresentaram uma notável diminuição da sua viscosidade, chegando a atingir valores percentuais de redução de viscosidade que variaram entre 75 e 91%, na concentração de 14% v/v de gás condensado. A partir desta concentração a viscosidade continua a decair, porém de forma mais atenuada, e o uso do condensado acima desta concentração pode significar gastos desnecessários com o solvente com a finalidade de se reduzir a viscosidade de óleos pesados. O óleo D foi o que apresentou os maiores percentuais de redução da viscosidade enquanto o óleo B foi o que apresentou os mais baixos valores. Comparando o gás condensado aos outros três solventes orgânicos testados, o condensado apresentou um comportamento bem semelhante ao tolueno quando analisadas as suas capacidades de redução da viscosidade dos óleos estudados.

Alocação de recursos financeiros em projetos de risco na exploração de petróleo

As recentes mudanças no setor petrolífero implicam um novo ambiente de exploração de intensa competição no Brasil. As tendências de internacionalização da exploração obrigam as empresas a adotarem técnicas padronizadas de avaliação e comparação de prospectos visando à redução do risco. Dentro dessa perspectiva, os indivíduos necessitam de um processo decisório que contemple os objetivos da empresa, as metas desejadas e as restrições orçamentárias. Este artigo descreve um sistema teórico e prático de suporte à tomada de decisão baseada na teoria da utilidade e da análise da decisão, com o objetivo de estimar a melhor alocação de capital em uma bacia sedimentar. Além disso, esse sistema possibilita estimar o melhor nível de participação financeira de uma firma em um projeto de exploração de petróleo realizado em parceria.

Perfil dos acidentes de trabalho em refinaria de petróleo

OBJETIVO: O trabalho em refinarias de petróleo envolve o risco de acidentes triviais e ampliados. Os dados nacionais apontam para a relevância dos acidentes nesse setor. Assim, realizou-se pesquisa com o objetivo de identificar o perfil e avaliar a adequação dos instrumentos de registro dos acidentes de trabalho em refinaria. MÉTODOS: Foram padronizadas e analisadas informações referentes aos acidentes de trabalho nas atividades de produção e manutenção registradas em uma refinaria de petróleo do Estado do Rio de Janeiro, no ano de 1997. A população estudada constituiu-se de 153 pessoas, sendo 83 trabalhadores próprios lesionados e 69 trabalhadores terceirizados lesionados. As variáveis analisadas foram: tipo de acidente, modo de operação e função do trabalhador lesionado. RESULTADOS: Em relação aos trabalhadores próprios, houve predominância dos chamados acidentes triviais (54,2%) e quanto ao modo de operação, houve concentração dos acidentes nas atividades em operação normal (62,9%). Quanto aos trabalhadores terceirizados, os acidentes triviais (75,5%) tiveram predominância mais acentuada; e quanto ao modo de operação, houve um domínio quase total dos acidentes na atividade de manutenção (96,8%). CONCLUSÕES: Os resultados mostraram um perfil de acidentes que afeta principalmente os níveis hierárquicos mais baixos, concentrando-se de modo geral nas atividades de manutenção, além da necessidade de modificações no sistema de registro e investigação de acidentes por parte da empresa.

Alteração de enzimas hepáticas em trabalhadores de refinaria de petróleo

OBJETIVO: A exposição ocupacional típica de uma refinaria de petróleo pode alterar a função hepática de seus trabalhadores. Assim, o objetivo do estudo foi identificar fatores de risco de alterações em enzimas hepáticas em trabalhadores de uma refinaria de petróleo. MÉTODOS: Os trabalhadores de uma refinaria de petróleo, localizada em São Francisco do Conde, Estado da Bahia, eram submetidos a exames periódicos anuais de 1982 a1998. O estudo caso-controle investigou todos os 150 casos de indivíduos com alteração simultânea de gama-glutamil transferase e de alanino amino transferase, de pelo menos 10% acima do valor de referência. Como controles, foram selecionados 150 indivíduos sem quaisquer alterações de enzimas hepáticas ou de bilirrubinas, desde a sua admissão. Foram calculadas as razões de chance e respectivos intervalos de confiança de 95% a partir de modelos de regressão logística. RESULTADOS: Em todos os setores de produção, o risco de alteração de enzimas hepáticas foi significantemente mais elevado do que no setor administrativo (RC=5,7; IC 95%: 1,7-18,4), estando controlados os efeitos do álcool, obesidade e antecedentes médicos de hepatite. No período 1992-1994 foram registrados 89 casos, 88 deles provieram dos diversos setores da produção. CONCLUSÕES: A exposição ocupacional desempenha papel importante na determinação de alterações de enzimas hepáticas em trabalhadores do refino de petróleo, além dos fatores de risco eminentemente biológicos e/ou comportamentais como obesidade e o consumo de álcool.

Contribuição para o estudo de avaliação do desempenho de um sistema de estabilização anaeróbia e utilização do gás produzido

Dissertação apresentada na Faculdade de Ciências e Tecnologia da Universidade Nova de Lisboa para obtenção do Grau de Mestre em Engenharia do Ambiente,Perfil Engenharia Sanitária

Gás sulfídrico nas redes de águas residuais

Os colaboradores que realizam a sua atividade profissional, no setor das águas residuais, reconhecem que a sua atividade é perigosa. Esse conhecimento, foi adquirido pela experiência obtida ao longo dos anos, pelas várias formações e pelas notícias de acidentes, muitas vezes mortais, que têm acontecido na atividade. Muita das vezes, os colaboradores têm dificuldade em aceitar o risco, porque na realidade não existe um histórico conhecido do que se passa no interior das redes de drenagem de águas residuais e consideram que o risco é apenas teórico. Os portugueses são um Povo muito ligado à Cultura Popular,e são os ditados populares que melhor sintetiza as ideias expressas pelos trabalhador português “Ver para Crer, Como São Tomé” (SOUSA, Marcelo Rebelo de, Os Evangelhos de 2001, Lisboa, Bertrand Editora, 2001]. O objetivo principal com este trabalho, foi evidenciar que existem gases no interior das caixas de visita, mas principalmente, demostrar que seu aparecimento e respetiva concentração, é variável e que ocorre sem aviso prévio! Tornando assim, os trabalhos no interior das caixas de visita e das redes de drenagem de águas residuais domesticas, locais perigosos para quem opera no seu interior, sem a correta utilização dos equipamentos de proteção individual, (Epis e Epc). Sendo necessário, reforçar, a constante informação e formação para a utilização dos equipamentos de proteção individual e coletiva. Com o presente estágio, pretendeu-se iniciar um registo histórico de medições nas redes de drenagem de águas residuais domésticas. Com o resultado das medições que serão obtidas, pretende-se uma “Radiografia Fotográfica” ao interior das caixas de visitas das redes de drenagem de águas residuais. Com os resultados deste estudo, pretende-se contribuir de forma clara e objetiva, para os perigos iminentes que existem efetivamente, no interior das redes de saneamento, com a presença de altas concentrações de gás sulfídrico, nocivo para a vida humana!

Caracterização da industria petrolifera e do georrecurso petróleo

Dissertação apresentada à Faculdade de Ciências e Tecnologia da Universidade Nova de Lisboa para obtenção do grau de Mestre em Engenharia Geológica (Georrecursos)

Possibilidade e rentabilidade da utilização do gás de xisto em Portugal

Mestrado em Engenharia Mecânica- Energia