Design, analysis and implementation of a versatile low level radio frequency system for accelerating cavities

179 p.

Estrategias de arranque de biofiltros orgánicos para el tratamiento de corrientes gaseosas contaminadas con compuestos de azufre

[ES]El disulfuro de carbono (CS2) y el sulfuro de hidrógeno (H2S) son gases especialmente tóxicos presentes en una gran cantidad de emisiones gaseosas industriales, principalmente en la producción de fibras de rayón a partir de celulosa en el caso del CS2, y en la industria petroquímica en el caso del H2S. La legislación vigente en cuanto a las emisiones de estos compuestos se refiere hace que su tratamiento sea, en muchos casos, necesario. La biofiltración como tecnología para el tratamiento de corrientes gaseosas contaminadas se ha convertido en los últimos años en una alternativa a los tratamientos físico-químicos empleados hasta la fecha. Sin embargo, uno de los principales obstáculos a la hora de la implantación de este tratamiento biológico a escala industrial es la duración del periodo de aclimatación de la biomasa encargada de degradar los contaminantes, que en función del compuesto a tratar puede resultar demasiado largo para la aplicación comercial de esta tecnología. El presente trabajo se centra en el estudio de estos periodos de arranque y aclimatación, especialmente lentos en el caso del CS2, y propone una estrategia de arranque basada en la reutilización de biomasa capaz de degradar los compuestos de interés, almacenada tras usos anteriores, que permite reducir el tiempo necesario para alcanzar eficacias de eliminación elevadas. Paralelamente, se ha concluido que paradas de corta duración no afectan de manera importante a la operación del sistema.

Estudo do impacto do complexo petroquímico COMPERJ na atmosfera

Os modelos de dispersão de ar têm sido utilizados amplamente para investigação de padrões de dispersão, comportamento de emissões, estimativas de potenciais riscos a saúde humana, elaboração de propostas de gerenciamento ambiental e, também, na previsão de impacto da qualidade do ar. Alguns modelos, homologados por agência de regulação de alguns países ou comunidades, servem de base para as análises de risco com auxílio de simulação. Somente após este tipo de análise uma unidade fabril terá direito à sua instalação e operação nestes países. Nesta dissertação, serão abordados os principais poluentes presentes em uma indústria petroquímica básica, uma revisão sobre os principais tipos de modelos existentes no mercado e um estudo de caso será realizado empregando os modelos AERMOD e OZIPR/SAPRC. A indústria petroquímica básica a servir de modelo será o Complexo Petroquímico do Rio de Janeiro, que deverá ser instalado no município de Itaboraí e com operação prevista para o ano de 2012. De acordo com as simulações realizadas neste trabalho, o poluente NOx apresentou os resultados mais críticos violando em algumas áreas os padrões primários e secundários de emissão. Diante deste fato, o ozônio se tornou um poluente secundário importante a ser analisado. E para sua simulação, premissas tiveram que ser tomadas, devido a ausência de dados, criando cenários que apresentaram resultados díspares: Ora violando os limites, ora se mantendo abaixo deles. Apesar disso, estes cenários apontaram a mesma solução para minimizar esta formação de ozônio: controlar as emissões de compostos orgânicos voláteis.

Utilización de la lógica borrosa en la selección de personas e ideas para la participación en programas públicos de ayuda a la creación de empresas

[ES] Se propone en este trabajo un modelo de control borroso que ayude a filtrar y seleccionar las solicitudes de subvención que pueda recibir una institución pública en un programa de fomento para la creación y desarrollo de nuevas iniciativas empresariales. Creemos que la utilización de la lógica borrosa presenta ventajas sobre los procedimientos ordinarios ya que nos movemos en un escenario de actuación complejo y vago. El control borroso introduce el conocimiento de los expertos de un modo muy natural mediante variables lingüísticas y procesos de inferencia propios del lenguaje ordinario, lo que facilita la toma de decisiones en situaciones complejas. Nuestro modelo considera por un lado la idea empresarial y por otro la persona . Los indicadores y criterios que los expertos consideran relevantes para la evaluación de la subvención son modelados mediante variables lingüísticas y tratados como antecedentes y consecuentes de un motor de inferencia borroso, cuya salida nos proporciona la valoración final de la solicitud. Al final de nuestro trabajo resolvemos un caso práctico sencillo para aclarar el procedimiento.

Las políticas tecnológicas y de innovación en la Comunidad Autónoma de Euskadi: El caso de los Clusters

[ES] En el presente trabajo se ha tratado de analizar la evolución de las políticas tecnológicas y de innovación en la Comunidad Autónoma de Euskadi (CAE), en las últimas tres décadas, prestando especial atención a la política de clusters. Es evidente el avance tecnológico e innovador experimentado por Euskadi en este período, basado en la estrecha cooperación desarrollada entre las universidades, las instituciones públicas y las empresas privadas. En este marco, la CAE fue pionera en el diseño y puesta en marcha de una política de clusters a principios de los años noventa. Tras más de dos décadas de funcionamiento de dicha política, ésta parece haberse consolidado existiendo en la actualidad 13 asociaciones cluster en Euskadi.

Puesta en marcha de negocios digitales

[ES] El presente TFG plantea una reflexión sobre la puesta en marcha de un negocio digital en el contexto empresarial de hoy en día. Se trata con ello de identificar pistas que resulten clave en el proceso de arranque de un negocio online exitoso. Para ello, se estudia el contexto empresarial en la era digital, así como la evolución de este en los últimos años con el paso de negocios puramente offline, a una combinación de estos, o a negocios puramente online. Una vez puestos en situación, se analizan algunos factores que resultan clave para iniciar un negocio online, como son los beneficios que estos ofrecen, así como los errores más comunes cometidos en negocios digitales. En este contexto, analizamos las estrategias empresariales seguidas por negocios digitales de éxito, considerando algunos ejemplos de los diferentes modelos de negocios digitales existentes hasta la fecha. El objetivo último es extraer algunas conclusiones generales que permitan orientar las decisiones de puesta en funcionamiento de un negocio digital.

Modelling non-linearities in a MEMS square wave oscillator

The modelling of the non-linear behaviour of MEMS oscillators is of interest to understand the effects of non-linearities on start-up, limit cycle behaviour and performance metrics such as output frequency and phase noise. This paper proposes an approach to integrate the non-linear modelling of the resonator, transducer and sustaining amplifier in a single numerical modelling environment so that their combined effects may be investigated simultaneously. The paper validates the proposed electrical model of the resonator through open-loop frequency response measurements on an electrically addressed flexural silicon MEMS resonator driven to large motional amplitudes. A square wave oscillator is constructed by embedding the same resonator as the primary frequency determining element. Measurements of output power and output frequency of the square wave oscillator as a function of resonator bias and driving voltage are consistent with model predictions ensuring that the model captures the essential non-linear behaviour of the resonator and the sustaining amplifier in a single mathematical equation. © 2012 IEEE.

The rise heights of low-and high-Froude-number turbulent axisymmetric fountains

We present the results of an experimental investigation across a broad range of source Froude numbers, 0. 4 ≤ Fr 0 ≤ 45, into the dynamics, morphology and rise heights of Boussinesq turbulent axisymmetric fountains in quiescent uniform environments. Typically, these fountains are thought to rise to an initial height, z i, before settling back and fluctuating about a lesser (quasi-) steady height, z ss. Our measurements show that this is not always the case and the ratio of the fountain's initial rise height to steady rise height, λ = z i/z ss, varies widely, 0. 5 ≈ λ ≈ 2, across the range of Fr 0 investigated. As a result of near-ideal start-up conditions provided by the experimental set-up we were consistently able to form a vortex at the fountain's front. This enabled new insights into two features of the initial rise of turbulent fountains. Firstly, for 1. 0 ≈ Fr 0 ≈ 1. 7 the initial rise height is less than the steady rise height. Secondly, for Fr 0 ≈ 5. 5, the vortex formed at the fountain's front pinches off, separates from the main body and rises high above the fountain; there is thus a third rise height to consider, namely, the maximum vortex rise height, z v. From our observations we propose classifying turbulent axisymmetric fountains into five regimes (as opposed to the current three regimes) and present detailed descriptions of the flow in each. Finally, based on an analysis of the rise height fluctuations and the width of fountains in (quasi-) steady state we provide further insight into the physical cause of height fluctuations. © 2011 Cambridge University Press.

Thermal shock resistance of air plasma sprayed thermal barrier coatings

The spallation resistance of an air plasma sprayed (APS) thermal barrier coating (TBC) to cool-down/reheat is evaluated for a pre-existing delamination crack. The delamination emanates from a vertical crack through the coating and resides at the interface between coating and underlying thermally grown oxide layer (TGO). The coating progressively sinters during engine operation, and this leads to a depth-dependent increase in modulus. Following high temperature exposure, the coating is subjected to a cooling/reheating cycle representative of engine shut-down and start-up. The interfacial stress intensity factors are calculated for the delamination crack over this thermal cycle and are compared with the mode-dependent fracture toughness of the interface between sintered APS and TGO. The study reveals the role played by microstructural evolution during sintering in dictating the spallation life of the thermal barrier coating, and also describes a test method for the measurement of delamination toughness of a thin coating. © 2014 Elsevier Ltd.

Origin of insulating behavior of the p-type LaAlO3/SrTiO3 interface: Polarization-induced asymmetric distribution of oxygen vacancies

It is revealed from first-principles calculations that polarization-induced asymmetric distribution of oxygen vacancies plays an important role in the insulating behavior at p-type LaAlO3/SrTiO3 interface. The formation energy of the oxygen vacancy (V-O) is much smaller than that at the surface of the LaAlO3 overlayer, causing all the carriers to be compensated by the spontaneously formed V-O's at the interface. In contrast, at an n-type interface, the formation energy of V-O is much higher than that at the surface, and the V-O's formed at the surface enhance the carrier density at the interface. This explains the puzzling behavior of why the p-type interface is always insulating but the n-type interface can be conducting.

Zn2SiO4/ZnO Core/Shell Coaxial Heterostructure Nanobelts Formed by an Epitaxial Growth

Si-doped ZnO can be synthesized on the surface of the early grown Zn2SiO4 nanostructures and form core/ shell coaxial heterostructure nanobelts with an epitaxial orientation relationship. A parallel interface with a periodicity array of edge dislocations and an inclined interface without dislocations can be formed. The visible green emission is predominant in PL spectra due to carrier localization by high density of deep traps from complexes of impurities and defects. Due to band tail localization induced by composition and defect fluctuation, and high density of free-carriers donated by doping, especially the further dissociation of excitons into free-carriers at high excitation intensity, the near-band-edge emission is dominated by the transition of free-electrons to free-holes, and furthermore, exhibits a significant excitation power-dependent red-shift characteristic. Due to the structure relaxation and the thermalization effects, carrier delocalization takes place in deep traps with increasing excitation density. As a result, the green emission passes through a maximum at 0.25I(0) excitation intensity, and the ratio of the violet to green emission increases monotonously as the excitation laser power density increases. The violet and green emission of ZnO nanostructures can be well tuned by a moderate doping and a variation in the excitation density.

亚硝化—厌氧氨氧化处理猪场废水研究

猪场废水COD浓度高、氨氮浓度高、悬浮物浓度高，已成为农村面源污染的主要来源，并严重威胁到农村饮用水安全。猪场废水氨氮浓度高、处理难度大，如何采用经济高效的方法，去除氨氮使其达到排放标准，一直是猪场废水处理中面临的重要难题。 厌氧氨氧化是近年受到国内外水处理研究者广泛关注的新型生物脱氮技术，具有不需要外加有机碳源、节省供氧量、降低能耗等优点。虽然国内外研究者对厌氧氨氧化过程的脱氮机理、厌氧氨氧化菌的生理生化特性等进行了多方面的研究，但已有的报道大多以模拟废水为研究对象，以猪场废水为研究对象的报道，在国内外文献中极少有报导。 本论文以猪场废水为主要研究对象，考察了猪场废水的亚硝化过程、厌氧氨氧化的启动过程，并对亚硝化和厌氧氨氧化联合用于猪场废水脱氮进行了探索。 1．论文首先研究了猪场废水的亚硝化过程，考察了废水水质和主要运行条件对亚硝化过程的影响。实验表明：（1）亚硝化阶段反应时间为8到10h时，出水中氨氮和亚硝酸盐浓度比可达到1：1～1：1.23，满足厌氧氨氧化反应对二者比例的要求；达到前述要求时，氨氮去除率达到58.3～65.6 %，亚硝化率在整个过程均保持在97 %以上，COD去除率在59.2～68.6 %；（2）曝气量（溶解氧）对亚硝化过程影响显著，随着曝气量增大，达到厌氧氨氧化要求的氨氮与亚硝酸盐氮浓度比例所需水力停留时间τ越短，pH出现明显下降的时间越短；（3）τ对应的pH在7.8～8.1之间，无需进行pH调节即可满足厌氧氨氧化反应对pH的要求；（4）氨氮和COD降解过程遵循一级反应动力学，氨氮和COD降解的速率常数分别为0.0656～0.0724 1/h和0.0491～0.0664 1/h。 2．在进行亚硝化过程研究的同时，以模拟废水为试验对象，进行厌氧氨氧化启动研究。以反硝化污泥和养殖厂储水池厌氧底泥的混合污泥作为接种污泥，历时大约100天，培育出具有厌氧氨氧化活性的污泥，氨氮和亚硝酸盐氮最高进水浓度分别为223.8 mg/L和171.4 mg/L，去除率最高分别达48%和41.5%，此时二者消耗比例为1.33：1。 3．在猪场废水的亚硝化研究完成和厌氧氨氧化过程初步启动成功后，在模拟废水中逐步加入猪场废水的亚硝化处理出水，逐步实现亚硝化和厌氧氨氧化的组合。亚硝化出水添加到厌氧反应器后，厌氧氨氧化反应仍可继续进行，且去除效率逐步提高。研究发现添加的亚硝化出水中携带的亚硝化细菌在厌氧氨氧化菌膜外层生长并累积，增加了厌氧氨氧化反应基质的传质阻力，妨碍了厌氧氨氧化效率的提高。 4．亚硝化－厌氧氨氧化实际工程应用探索中，生物接触氧化池可在有效去除废水中的有机物的同时实现亚硝化，出水中氨氮和亚硝酸盐比例平均为1.10，可满足后续厌氧氨氧化的要求；在适宜的进水浓度和温度下，ABR池出现了厌氧氨氧化启动的迹象；研究同时发现，水质的波动和气温的变化是工程中影响厌氧氨氧化菌活性的重要因素。 论文的主要创新点在于：（1）以猪场废水为研究对象，以实现厌氧氨氧化为目标，对亚硝化过程进行了比较详细的考察，获得了亚硝化出水满足厌氧氨氧化要求的工艺条件，通过对其COD和氨氮降解过程的考察，得出亚硝化阶段COD降解和氨氮去除的动力学模型；（2）对亚硝化－厌氧氨氧化处理猪场废水进行了探索，确立了影响其污染物去除率稳定的重要因素。 论文的上述研究成果，为厌氧氨氧化技术的实用性研究提供理论依据。 Piggery wastewater, which is characterized by high concentration of COD、ammonium and suspend substance, has become a most important source of non-point source pollution and also severely threats drinking water security in rural area. How to discharge piggery wastewater with the ammonium concentration meeting standard by economical and effective method? This is the most urgent problem in piggery wastewater treatment. As a new biological nitrogen removal technology, Anammox process has been paid more and more attention by researchers all over the world. Anammox has advantages of no need of organic carbon addition, low oxygen consumption and energy consumption. Plenty of investigations have been carried out to the mechanism, physiological and biochemical characteristic of bacteria about Anammox. Most of researches focused on synthetic wastewater, there is rare report about its application in piggery wastewater. In this paper，experimental studies were performed to investigate Sharon process in treatment of piggery wastewater，the start up process of Annammox using synthetic wastewater were studied, the feasibility of applying Sharon-Anammox process in the nitrogen removal of piggery wastewater was evaluated. 1. Sharon process of piggery wastewater was firstly investigated to analyze the effects of water quality and main running parameters, which meet the NH4+-N to NO2--N ratio requirement of successive Anammox. Results showed: (1)During Sharon Process，after 8～10 hours’ reaction the NH4+-N to NO2--N ratio in effluent reached 1:1.0～1:1.23, when the removal percentage of NH4+-N was 58.3～65.6 %, a semi-nitration rate of above 97 % was achieved during the process; meanwhile 59.2～68.6 % of the COD was also removed. (2)The aeration rate（oxygen） had obvious effect on the hydraulic retention time(τ) which met the NH4+-N to NO2--N ratio requirement of Anammox. As aeration rate increased, the hydraulic retention time(τ) was shortened. (3) The pH corresponding to τ was between 7.8 and 8.1, thus it needed no artificial adjustment. (4) The reduction of ammonia and COD followed the first-order reaction kinetics. The velocity constants of ammonia and COD were 0.0656～0.0724 1/h and 0.0491～0.0664 1/h, respectively. 2. The startup of Anammox process using the artificial wastewater was performed simultaneously with Sharon. The aim was to investigate the running parameters of Anammox and make foundation for the combination stage. By using the mixture of denitrifying sludge and anaerobic sludge in tank of the breeding factory, sludge of Anammox activity was cultivated in UASB after 100 days. The removal percentage of NH4+-N and NO2-N were up to 48% and 41.5%, respectively, when the NH4+-N and NO2-N influent concentration were 223.8 mg/L and 171.4 mg/L, respectively, the NH4+-N and NO2-N removal rate was 1.33:1. 3. After investigation of Sharon and startup of Anammox, effluent of Sharon process was added into the synthetic wastewater to combine Sharon and Anammox step by step. It took some time after the addition of Sharon effluent that Anammox reaction continued and the removal rate kept increasing. It indicated that nitrifying bacteria were carried by the Sharon effluent cumulated in the outer layer of Anammox. This enhanced transfer resistance of Anammox reaction and the increasing removal rate was restrained. 4. In the bio-contact oxidation pond of practical project, Sharon process were carried out successfully and organic compounds were removed effectively. An average NO2-N/ NH4+-N rate of 1:1.0 was achieved in the effluent, which met the requirement of successive Anammox. Under condition of suitable influent concentration and temperature, there was evidence that Anammox could start up in ABR. The variety of wastewater and temperature had great affects on Anammox activity in practical engineering. Innovation of this paper: (1) The Sharon process for treating piggery wastewater was discussed in details. Technological parameters that met requirement of Anammox were obtained. The dynamic models of COD and ammonium removal in the process were educed. (2) Sharon-Ananmmox for treatment of piggery wastewater was investigated, and the primary influencing factors was studied. This paper could be a theoretical consult for research of Anammox utility.

猪场废水短程硝化反硝化-厌氧氨氧化脱氮研究

畜禽废水是农村水环境污染的主要来源之一，其处理的难点在于脱氮。传统生物脱氮法具有能耗高、需大量外加碳源等缺点，开发低成本、高效率的新型生物脱氮技术具有重要意义。 本研究将短程硝化反硝化和厌氧氨氧化两种脱氮新技术结合，让前者为后者创造去除可降解COD、降低总氮负荷、调整pH、调整氨氮和亚硝酸盐氮浓度比例等进水条件，而后者可在无需外加碳源的条件下进一步脱氮，二者结合可成为高氨氮、低C/N废水脱氮的新途径。 试验以低碳氮比猪场废水为研究对象，首先进行了短程硝化反硝化预处理研究，同时启动并运行调控厌氧氨氧化反应器，最后以经过短程硝化反硝化预处理的猪场废水为进水，进行厌氧氨氧化脱氮考察。实验表明：（1）短程硝化反硝化作为厌氧氨氧化的预处理工序是可行的。猪场废水通过短程硝化反硝化，可以达到基本去除可生化COD、部分脱氮、控制出水氨氮和亚硝酸盐氮浓度之比在1︰1左右、pH在7.5～8.0的目的， COD和总氮平均去除率分别为64.3%、49.1%,出水可达到厌氧氨氧化反应的进水要求。（2）采用模拟废水启动厌氧氨氧化反应器，经过5个月左右的运行调控，反应器启动成功并稳定运行，最高总氮去除率为87.1%，总氮容积去除率最高达到0.14kg/m3.d；整个稳定阶段，氨氮、亚硝酸盐氮、硝酸盐氮的变化量之比为1︰1.21︰0.33。（3）经过短程硝化反硝化预处理的猪场废水厌氧氨氧化脱氮效果稳定，氨氮、亚硝酸盐氮、总氮、COD的平均去除率分别为93.0%、99.4%、84.6%、18.1%，处理效果与模拟废水处理系统相比无明显变化。（4）经过短程硝化反硝化预处理后，猪场废水中残留有机物成分在厌氧氨氧化反应过程中无显著变化，主要为酯类和烷烃类物质；残留有机物对厌氧氨氧化效果无明显影响。（5）采用PCR技术进行特殊功能菌种检测，结果表明模拟废水处理系统和猪场废水处理系统的菌群中均含有厌氧氨氧化菌和好氧硝化菌；通过blast比对，厌氧氨氧化菌扩增序列与未培养的Planctomycetales菌和Candidatus Brocadia fulgida菌16S rRNA部分序列相似性分别为95％、90%。（6）MPN法菌种计数结果显示，模拟废水处理系统和猪场废水处理系统的菌群中均含有硝化细菌、亚硝化细菌和少量反硝化菌，实验条件下的微生物系统是一个厌氧氨氧化菌与好氧硝化菌、反硝化菌共存的系统。 Poultry wastewater is one of the main source of water pollution in rural areas，and nitrogen removal is the most difficult part in treating poultry wastewater. There are some disadvantages in traditional nitrogen removal, such as high energy consumption and more additional organic carbon. It is important to develop ecolomical and efficient technologyies. Shortcut nitricfication/denitrification, as a pretreatment process, was combined with Anammox in this research, so that part of total nitrogen and most degradable COD could be removed by the former, and further nitrogen removal could be implemented by the latter. The combination of the two technologies was a new approach to treat wastewater with high ammonium and low C/N. Piggery wastewater with low C/N was treated in lab-scale experiment. Firstly, shortcut nitrification/denitrification was investigated, and Anammox reactor was started up successfully at the same time. Then piggery wastewater after pretreatment was treated by Anammox. The results showed :(1) It was feasible to take nitrification/denitrification as the pretreatment process of Anammox. By using this process, part of total nitrogen and COD were removed, the ratio of ammonium and nitrite reached around 1︰1 and the pH was about 7.8, which were favorable for Anammox. The average removal percentage of COD and total nitrogen were about 64.3% and 49.1%, respectively. (2) Simulated wastewater was used to start up Anammox reactor. The reactor was started up successfully within 5 months and stable performance was achieved. The highest nitrogen removal reached 87.1% and the biggest volumetric total nitrogen removal rate reached 0.14kg/m3.d. The average ratio of ammonium, nitrite and nitrate was 1:1.21:0.33. (3)Taking the effluent of shortcut nitrification/denitrification as the influent, the nitrogen removal efficiency of Anammox was stable, and the the average removal percentage of ammonium, nitrite, total nitrogen and COD were 93.0%, 99.4% , 84.6% and 18.1%, respectively, which had little difference with that by using simulated wastewater..(4) After pretreatment, the residual organic carbon in piggery wastewater showed no obvious change during the Anammox process, and the main organic compounds were saturated hydrocarbon and ester, which had no obvious negative effect on Anammox process.(5) By PCR technology, the existence of Anammox bacteria was confirmed and the aerobic nitrifying bacteria was found to coexist as well. The result of blast showed that the identities of Anammox bacterium to part of 16S rRNA sequence of uncultured Planctomycetales bacterium and Candidatus Brocadia fulgida bacterium were 95% and 90%, respectively.（6）By MPN method, nitrite oxidizer, ammonium oxidizer and denitrification bacteria were detected in both simulated and piggery wastewater treatment system of Anammox, and the microorganism system was composed of Anammox bacteria，aerobic bacteria and denitrification bacteria together.

The temporal and spatial evaluation on China's agricultural policy output since 1978

Since reform and opening up, how much contribution has China's implementation of new agricultural policy made to agricultural output? This paper is trying to establish an agricultural policy output econometric model for doing a quantitative analysis of China's new agricultural policy. The results show that China's agricultural policies on agricultural output have an average contribution rate of about 7% since 1978, which is consistent with the OECD's basic forecast. There are obvious temporal and spatial differences. Generally speaking, we can divide the contribution of agricultural policy into three periods, which are the start-up phase from 1978 to 1991 (14 years), the stationary phase from 1992 to 2002 (11 years) and the rising phase from 2003 to 2008 (6 years). In space, the contribution of agricultural policy underwent a process from the all-low in the start-up phase, the gradual increase in the stationary phase to the all-high in the rising phase. Northern and western regions are more sensitive to policies. There are three major factors that can affect the contribution of regional agricultural policies, which are the process of national industrialization strategy, terrain and the level of local finance.

动漫行业创业者胜任特征研究

Venture has become an important force for the sustainable economic growth of China, However, research on entrepreneurs is far failed to meet the actual needs, Animation and Comic Industry is an important component of the state-led Cultural and Creative Industries. Entrepreneurship is the rapid growth of population, but the empirical research on the Animation and Comic Industry entrepreneurs’ Competent Characteristic Model is rarely heard. As a manager of a national incubator which major in Cultural and Creative Industry, study these entrepreneurs competent characteristics is my responsibility. As an exploration, the study uses Competent Characteristic Model of classical design methods and behavior events interview method, and selects entrepreneurs which of animation and comic industry business start-up period as the objects. Through coding analysis of 31 entrepreneurs’ interview information, completed the amendment to the dictionary coding, and ultimately construct the animation and comic industry entrepreneurs need to have the threshold competence model and differentiating competence model. Differentiating competence model includes six competencies: tolerance and optimism, cooperation, creative innovation, pool talents, vision, decision-making and tempo control. Threshold competence model includes twenty features, divided into three dimensions: personal characteristics, knowledge quality, capacity of the quality. Knowledge and capacity of the quality are closely related to the core work of entrepreneurs, Personal characteristics concern the deep-seated motivation of the entrepreneurs. The study also analyses and discusses the characteristics of the entrepreneurs on the demographic variables.