Desenvolvimento e estudo de materiais híbridos siloxano-poli(óxipropileno) para liberação prolongada do cloridrato de propranolol

Pós-graduação em Química - IQ

Internal fit of two all-ceramic systems and metal-ceramic crowns

Objectives: The aim of this study was to investigate the internal fit (IF) of glass-infiltrated alumina (ICA - In-Ceram Alumina), yttria-stabilized tetragonal zirconia polycrystals (Y-TZP - IPS e.max ZirCAD), and metal-ceramic (MC - Ni-Cr alloy) crowns. Material and Methods: Sixty standardized resin-tooth replicas of a maxillary first molar were produced for crown placement and divided into 3 groups (n=20 each) according to the core material used (metal, ICA or Y-TZP). The IF of the crowns was measured using the replica technique, which employs a light body polyvinyl siloxane impression material to simulate the cement layer thickness. The data were analyzed according to the surfaces obtained for the occlusal space (OS), axial space (AS) and total mean (TM) using two-way ANOVA with Tukey's multiple comparison test (p<0.05). Results: No differences among the different areas were detected in the MC group. For the Y-TZP and ICA groups, AS was statistically lower than both OS and TM. No differences in AS were observed among the groups. However, OS and TM showed significantly higher values for ICA and Y-TZP groups than MC group. Comparisons of ICA and Y-TZP revealed that OS was significantly lower for Y-TZP group, whereas no differences were observed for TM. Conclusions: The total mean achieved by all groups was within the range of clinical acceptability. However, the metal-ceramic group demonstrated significantly lower values than the all-ceramic groups, especially in OS.

On the nu SiO infrared absorption of polysiloxane films

The infrared absorption of polysiloxanes involves a strong band at around 1050 cm(-1), attributed to the antisymmetric vibration of siloxane bridges. The splitting of this band into two components is generally attributed to coupling between next-neighbor siloxane groups along the polysiloxane chain. From a quantitative analysis of the spectra of these materials, we find that this splitting is larger when the material is in thin-film form, and that the relative intensity of the two components is polarization dependent. We show that these effects are fully understandable in the theoretical framework of infrared absorption by thin films, and are related to long-range dipolar interactions responsible for the longitudinal-transverse splitting effect in crystalline materials. As a consequence, the polarization dependence of the infrared absorption observed for thin films does not appear to be associated with an orientational ordering in the film. (c) 2012 Elsevier B.V. All rights reserved.

Internal fit of two all-ceramic systems and metal-ceramic crowns

OBJECTIVES: The aim of this study was to investigate the internal fit (IF) of glass-infiltrated alumina (ICA - In-Ceram Alumina), yttria-stabilized tetragonal zirconia polycrystals (Y-TZP - IPS e.max ZirCAD), and metal-ceramic (MC - Ni-Cr alloy) crowns. MATERIAL AND METHODS: Sixty standardized resin-tooth replicas of a maxillary first molar were produced for crown placement and divided into 3 groups (n=20 each) according to the core material used (metal, ICA or Y-TZP). The IF of the crowns was measured using the replica technique, which employs a light body polyvinyl siloxane impression material to simulate the cement layer thickness. The data were analyzed according to the surfaces obtained for the occlusal space (OS), axial space (AS) and total mean (TM) using two-way ANOVA with Tukey s multiple comparison test (p<0.05). RESULTS: No differences among the different areas were detected in the MC group. For the Y-TZP and ICA groups, AS was statistically lower than both OS and TM. No differences in AS were observed among the groups. However, OS and TM showed significantly higher values for ICA and Y-TZP groups than MC group. Comparisons of ICA and Y-TZP revealed that OS was significantly lower for Y-TZP group, whereas no differences were observed for TM. CONCLUSIONS: The total mean achieved by all groups was within the range of clinical acceptability. However, the metal-ceramic group demonstrated significantly lower values than the all-ceramic groups, especially in OS.

Evaluation of fluid transport processes in dental enamel. Methods to assess the relevance of enamel permeability in caries prevention and etching treatments.

This thesis evaluated in vivo and in vitro enamel permeability in different physiological and clinical conditions by means of SEM inspection of replicas of enamel surface obtained from polyvinyl siloxane impressions subsequently later cast in polyether impression ma-terial. This technique, not invasive and risk-free, allows the evaluation of fluid outflow from enamel surface and is able to detect the presence of small quantities of fluid, visu-alized as droplets. Fluid outflow on enamel surface represents enamel permeability. This property has a paramount importance in enamel physiolgy and pathology although its ef-fective role in adhesion, caries pathogenesis and prevention today is still not fully under-stood. The aim of the studies proposed was to evaluate enamel permeability changes in differ-ent conditions and to correlate the findings with the actual knowledge about enamel physiology, caries pathogenesis, fluoride and etchinhg treatments. To obtain confirmed data the replica technique has been supported by others specific techniques such as Ra-man and IR spectroscopy and EDX analysis. The first study carried out visualized fluid movement through dental enamel in vivo con-firmed that enamel is a permeable substrate and demonstrated that age and enamel per-meability are closely related. Examined samples from subjects of different ages showed a decreasing number and size of droplets with increasing age: freshly erupted permanent teeth showed many droplets covering the entire enamel surface. Droplets in permanent teeth were prominent along enamel perikymata. These results obtained through SEM inspection of replicas allowed innovative remarks in enamel physiology. An analogous testing has been developed for evaluation of enamel permeability in primary enamel. The results of this second study showed that primary enamel revealed a substantive permeability with droplets covering the entire enamel sur-face without any specific localization accordingly with histological features, without changes during aging signs of post-eruptive maturation. These results confirmed clinical data that showed a higher caries susceptibility for primary enamel and suggested a strong relationship between this one and enamel permeability. Topical fluoride application represents the gold standard for caries prevention although the mechanism of cariostatic effect of fluoride still needs to be clarified. The effects of topical fluoride application on enamel permeability were evaluated. Particularly two dif-ferent treatments (NaF and APF), with different pH, were examined. The major product of topical fluoride application was the deposition of CaF2-like globules. Replicas inspec-tion before and after both treatments at different times intervals and after specific addi-tional clinical interventions showed that such globule formed in vivo could be removed by professional toothbrushing, sonically and chemically by KOH. The results obtained in relation to enamel permeability showed that fluoride treatments temporarily reduced enamel water permeability when CaF2-like globules were removed. The in vivo perma-nence of decreased enamel permeability after CaF2 globules removal has been demon-strated for 1 h for NaF treated teeth and for at least 7 days for APF treated teeth. Important clinical consideration moved from these results. In fact the caries-preventing action of fluoride application may be due, in part, to its ability to decrease enamel water permeability and CaF2 like-globules seem to be indirectly involved in enamel protection over time maintaining low permeability. Others results obtained by metallographic microscope and SEM/EDX analyses of or-thodontic resins fluoride releasing and not demonstrated the relevance of topical fluo-ride application in decreasing the demineralization marks and modifying the chemical composition of the enamel in the treated area. These data obtained in both the experiments confirmed the efficacy of fluoride in caries prevention and contribute to clarify its mechanism of action. Adhesive dentistry is the gold standard for caries treatment and tooth rehabilitation and is founded on important chemical and physical principles involving both enamel and dentine substrates. Particularly acid etching of dental enamel enamel has usually employed in bonding pro-cedures increasing microscopic roughness. Different acids have been tested in the litera-ture suggesting several etching procedures. The acid-induced structural transformations in enamel after different etching treatments by means of Raman and IR spectroscopy analysis were evaluated and these findings were correlated with enamel permeability. Conventional etching with 37% phosphoric acid gel (H3PO4) for 30 s and etching with 15 % HCl for 120 s were investigated. Raman and IR spectroscopy showed that the treatment with both hydrochloric and phosphoric acids induced a decrease in the carbonate content of the enamel apatite. At the same time, both acids induced the formation of HPO42- ions. After H3PO4 treatment the bands due to the organic component of enamel decreased in intensity, while in-creased after HCl treatment. Replicas of H3PO4 treated enamel showed a strongly reduced permeability while replicas of HCl 15% treated samples showed a maintained permeability. A decrease of the enamel organic component, as resulted after H3PO4 treatment, involves a decrease in enamel permeability, while the increase of the organic matter (achieved by HCl treat-ment) still maintains enamel permeability. These results suggested a correlation between the amount of the organic matter, enamel permeability and caries. The results of the different studies carried out in this thesis contributed to clarify and improve the knowledge about enamel properties with important rebounds in theoretical and clinical aspects of Dentistry.

Biofilms on exposed monumental stones: mechanism of formation and development of new control methods

Within the stone monumental artefacts artistic fountains are extremely favorable to formation of biofilms, giving rise to biodegradation processes related with physical-chemical and visual aspect alterations, because of their particular exposure conditions. Microbial diversity of five fountains (two from Spain and three from Italy) was investigated. It was observed an ample similarity between the biodiversity of monumental stones reported in literature and that one found in studied fountains. Mechanical procedures and toxic chemical products are usually employed to remove such phototrophic patinas. Alternative methods based on natural antifouling substances are recently experimented in the marine sector, due to their very low environmental impact and for the bio settlement prevention on partially immersed structures of ships. In the present work groups of antibiofouling agents (ABAs) were selected from literature for their ability to interfere, at molecular level, with the microbial communication system “quorum sensing”, inhibiting the initial phase of biofilm formation. The efficacy of some natural antibiofoulants agents (ABAs) with terrestrial (Capsaicine - CS, Cinnamaldehyde - CI) and marine origin (Zosteric Acid - ZA, poly-Alkyl Pyridinium Salts – pAPS and Ceramium botryocarpum extract - CBE), incorporated into two commercial coatings (Silres BS OH 100 - S and Wacker Silres BS 290 - W) commonly used in stone conservation procedures were evaluated. The formation of phototrophic biofilms in laboratory conditions (on Carrara marble specimens and Sierra Elvira stone) and on two monumental fountains (Tacca’s Fountain 2 - Florence, Italy and Fountain from Patio de la Lindaraja - Alhambra Palace, Granada, Spain) has been investigated in the presence or absence of these natural antifouling agents. The natural antibiofouling agents, at tested concentrations, demonstrated a certain inhibitory effect. The silane-siloxane based silicone coating (W) mixing with ABAs was more suitable with respect to ethyl silicate coating (S) and proved efficacy against biofilm formation only when incompletely cured. The laboratory results indicated a positive action in inhibiting the patina formation, especially for poly-alkyl pyridinium salts, zosteric acid and cinnamaldehyde, while on site tests revealed a good effect for zosteric acid.

Entwicklung einer Methode mittels hochauflösender ICP-MS zur Bestimmung von Siliciumspuren in anorganischen und organischen Matrices sowie von Siloxanen in Geweben

Deutsch:Schwerpunkt dieser Arbeit war die Entwicklung einer Methode zur Spurenbestimmung von Silicium in organischen und anorganischen Matrices unter Verwendung der massenspektrometrischen Isotopenverdünnungsanalyse (MSIVA) an einem hochauflösenden induktiv gekoppelten Plasma-Massenspektrometer (HR-ICP-MS). Zusätzlich zur Elementspurenbestimmung wurde eine GC/HR-ICP-MS Kopplung entwickelt, die zur Analyse linearer und cyclischer Siloxane verwendet wurde.Die hier entwickelte Analysenmethode erlaubt Nachweisgrenzen für Silicium sowohl in organischen als auch in anorganischen Matrices im oberen ng/g-Bereich und ergab für die im Rahmen dieser Arbeit analysierten Proben Reproduzierbarkeiten von < 20%. Durch einfache Verdünnung nach der Probenvorbereitung in Verbindung mit dem sehr empfindlichen Detektionsverfahren sowie der internen Standardisierung mittels MSIVA erlaubt das Verfahren eine präzise Bestimmung von Silicium in jeglicher Matrix. Neben der Schnelligkeit und Einfachheit eignet sich die hier entwickelte Methode besonders für die Routineanalytik. Die gute Reproduzierbarkeit und der Vergleich mit Ergebnissen von zwei Interlaborstudien unterstreicht zusätzlich die Fähigkeit präzise und richtige Ergebnisse zur Zertifizierung an Standardreferenzmaterialien bezüglich des Siliciums im Spurenbereich zu liefern.Neben dem Gesamtgehalt von Silicium konnten medizinisch relevante Siliciumverbindungen analysiert und quantifiziert werden. Hierbei wurden niedermolekulare Polydimethlysiloxane (PDMS) untersucht, die als Nebenprodukte vor allem in Brustimplantaten auftreten. Grundlage für die Bestimmung dieser Siliciumspezies ist die Kopplung eines hochauflösenden ICP-MS an einen Gaschromatographen. Der hohe Ionisierungsgrad des ICP, gerade unter trockenen Plasmabedingungen, und der elementspezifische und sehr empfindliche massenspektrometrische Detektor erlauben in Verbindung mit dem GC die Bestimmung von Siloxanen bis in den pg/g-Bereich. Aus der Bestimmung des Gesamtgehalts an Silicium und der Bestimmung des Gehalts an den untersuchten Siliciumverbindungen können Vergleiche gemacht werden. Die Analyse beider Parameter ist mit Hilfe in dieser Arbeit entwickelten Methode möglich.Zusätzlich zur Siliciumbestimmung wurde der Gehalt an Platin in Humanproben analysiert, da bei der Herstellung der Füllung von Siliconimplantaten Platinkatalysatoren verwendet werden.

Wasserfreie, polymere Protonenleiter für Brennstoffzellen durch Immobilisierung von Imidazol

Es werden neuartige, polymere Protonenleiter vorgestellt die nach dem 'Konzept des polymergebunden Protonensolvens' realisiert wurden. Sie zeigen protonische Leitfähigkeit als intrinsische Eigenschaft, sodass keine zweite, flüssige Phase zur Protonenleitung nötig ist. Verwirklicht wurde das Konzept anhand von kammartigen Siloxanoligomeren und -polymeren, wobei Imidazol als Protonensolvens durch flexible Spacer kovalent an das Rückgrat gebunden ist. Durch Pfropfung mit imidazoltragenden Spacereinheiten wurden ferner Kieselgelnanopartikel oberflächenmodifiziert. Um die Auswirkungen der Immobilisierung von Imidazol auf die Leitfähigkeit zu untersuchen, wurden neben unterschiedlichen Molekulargewichten, die Verbindungen auch jeweils mit verschiedenen Spacerlängen synthetisiert. Die Materialien wurden umfassend charakterisiert und auf ihr thermisches Verhalten, Stabilität, Leitfähigkeit, Diffusion und dielektrisches Verhalten sowie auch nach Dotierung mit Säure untersucht. Thermisch stabil sind die Materialien bis ca. 200°C. Die Leitfähigkeiten betragen bis zu 1,5E-3 S/cm bei 160°C, welche aufgrund der Immobilisierung des Imidazols ausschließlich auf Strukturdiffusion zurückzuführen sind. Die Strukturdiffusion ist vergleichbar mit dem Grotthus-Mechanismus in Wasser und wird durch die lokale Mobilität der Imidazolmoleküle, d.h. durch die Glasübergangstemperatur des Systems bestimmt. Entsprechend wird das für Glasbildner typische Vogel-Tamman-Fulcher-Verhalten für alle untersuchten Transportprozesse gefunden. Die mit abnehmender Glasübergangstemperatur abnehmende mechanische Stabilität der Materialien kann, wie gezeigt ist, durch Compoundierung mit Kieselgelnanopartikeln entscheidend verbessert werden, was eine kostengünstige und aussichtsreiche Möglichkeit zur Herstellung von Membranen für Brennstoffzellen darstellt.

Grenzflächenspannung und Morphologie fließender zweiphasiger Polymermischungen

In der vorliegenden Arbeit wurde die Morphologie von zweiphasigen Polymermischungen unter Scherung in situ mit Hilfe einer Kombination aus optischer Scherzelle, Durchlichtmikroskop und computergestützten CCD-Kamera untersucht. Als Modellblends dienten die unverträglichen, bei Raumtemperatur flüssigen Polymersysteme Polyisobutylen (PIB)/Polydimethylsiloxan (PDMS) (I) und Poly(dimethyl-co-methylphenyl)siloxan/PDMS (II). Alle Komponenten verhalten sich bei den verwendeten Scherraten newtonisch.Eine der wichtigsten Einflussgrößen für die Blendmorphologie ist die Grenzflächenspannung gamma 12. Sie wurde für I und II mit Hilfe der Methode der Tropfenrelaxation (dynamisch) als Funktion der Zeit bestimmt. Diese Methode erlaubt die Messung von gamma 12 für Tropfen der Phase A in B sowie von Tropfen B in A. Bei der Methode des hängenden Tropfens (statisch) muss der Tropfen aus der Phase mit der höheren Dichte bestehen. Wo der Vergleich der beiden Methoden möglich ist, stimmen die Ergebnisse für beide Systeme sehr gut überein. Bei II sind die aus der Tropfenrelaxation erhaltenen gamma 12-Werte der beiden komplementären Zusammensetzungen im Rahmen des Fehlers gleich, bei I zeigt ein PIB-Tropfen in PDMS einen um 40 % niedrigeren Wert als ein PDMS-Tropfen in PIB, dies wird auf die Diffusion von kurzkettigen Anteilen des PDMS in die Grenzschicht zurückgeführt. Die Grenzflächenspannung hängt also unter Umständen auch bei binären Systemen deutlich von der Zusammensetzung ab.Für II wurde die Blendmorphologie über den gesamten Zusammensetzungsbereich untersucht. Die häufig beobachteten cokontinuierlichen Strukturen treten bei keiner Zusammensetzung auf. Die Phaseninversion erkennt man in einer sprunghaften Änderung der Tropfengröße zwischen phiPDMS <= 0,400 und 0,500; zudem lässt sich die Zeitabhängigkeit der Radien durch Auftragung gegen das Produkt aus der Deformation und dem Quadrat des Volumenbruchs der Tropfenphase für 0 <= phiPDMS <= 0,400 sowie 0,500 <= phiPDMS <= 1 normieren. Für I und II wurde die Morphologieentwicklung bei 25 °C nach Vorscherung bei 100 bzw. 50 s-1 und anschließendem Sprung der Scherrate auf deutlich niedrigere Werte als Funktion der Zeit verfolgt. Hierbei erhält man bei genügend langer Messdauer (mindestens 200 000-300 000 Schereinheiten) konstante Tropfengrößen. Zum einen handelt es sich dabei um pseudo-stationäre Werte, die nur durch Koaleszenz bestimmt sind, zum anderen um echte stationäre Radien, die durch gleichzeitig ablaufende Koaleszenz und Zerteilung entstehen. Für I liegen die stationären Mittelwerte auf der Zerteilungskurve, für II hingegen auf der Koaleszenzkurve.Der Einfluss eines grenzflächenwirksamen Additivs wurde anhand von I durch Zugabe des Blockcopolymer PIB-b-PDMS zu PIB untersucht. Der Vergleich des zeitlichen Verlaufs von gamma 12 mit der Morphologieentwicklung zeigt, dass das Additiv eine Stabilisierung der feinen Tropfen/Matrix-Struktur des Blends durch Hinderung der Koaleszenz und nicht durch Reduktion der Grenzflächenspannung bewirkt.

Surface layer formation in polymer melts and in solutions

In this work the surface layer formation in polymer melts and in polymer solutions have been investigated with the atomic force microscope (AFM). In polymer melts, the formation of an immobile surface layer results in a steric repulsion, which can be measured by the AFM. From former work it is know, that polydimethyl siloxane (PDMS) forms a stable surface layer for molecular weights above 12 kDa. In the present thesis, polyisoprene (PI) was investigated apart from PDMS, by a)measuring the steric surface interactions and b)measuring the surface slip in hydrodynamic experiments. If a polymer flows over a surface, the flow velocity at the surface is larger then zero. If case of a surface layer formation the flow plane changes to the top of the adsorbed layer and the surface slip is reduced to zero. By measuring the surface slip in hydrodynamic experiments, it is therefore possible to determine the presence of a stable surface layer. The results show no stable repulsion for PI and only a small decrease of the surface slip. This indicates that PI does not form a stable surface layer, but is only adsorbed weakly to the surface. Furthermore for 8 kDa PDMS the timescale of the formation of a surface layer was investigated by changing themaximal force the tip applied to the surface. With a repulsive force present, applying a higher force than 15 nN resulted in a destruction of the surface layer, indicated by attractive forces. Reducing the applied force below 15 nN then resulted in an increase of the repulsion to the former state during one minute, thus indicating that a surface layer can be formed within one minute even under the influence of continuous measurements. As a next step, mixtures of two PDMS homopolymers with different chain lengths have been investigated. The aim was to verify theoretical predictions that shorter chains should predominate at the surface due to their smaller loss in conformational entropy. The measurements where done in dependence of the volume fractions of short and long chain PMDS. The results confirmed the short chain dominance for all mixtures with less then 90 vol.% long chain PDMS. Surface layer formation in solution was investigated for superplasticizers which are industrially used as an additive to cement. They change the surface interaction between the cement grains from attractive to repulsive and the freshlymixed cement paste therefore becomes liquid. The aimin this part of the thesis was, to investigate cement particle interactions in a close to real environment. Therefore calcium silicate hydrate phases have been precipitated onto an AFM tip and onto a calcite crystal and the interaction between these surfaces have beenmeasured with and without addition of superplasticizers. The measurements confirmed the change from attraction to repulsion upon addition of superplasticizers. The repulsive steric interaction increased with the length of the sidechain of the superplasticizer, and the dependence of the range of the steric interactions on the sidechain length indicated that the sidechains are in a coiled conformation.

Abscheidung und Charakterisierung von Plasmapolymerschichten auf Fluorkohlenstoff- und Siloxan-Basis

In dieser Arbeit wurden Fluorkohlenstoff-basierte und siliziumorganische Plasmapolymerfilme hergestellt und hinsichtlich ihrer strukturellen und funktionalen Eigenschaften untersucht. Beide untersuchten Materialsysteme sind in der Beschichtungstechnologie von großem wissenschaftlichen und anwendungstechnischen Interesse. Die Schichtabscheidung erfolgte mittels plasmachemischer Gasphasenabscheidung (PECVD) an Parallelplattenreaktoren. Bei den Untersuchungen zur Fluorkohlenstoff-Plasmapolymerisation stand die Herstellung ultra-dünner, d. h. weniger als 5 nm dicker Schichten im Vordergrund. Dies wurde durch gepulste Plasmaanregung und Verwendung eines Gasgemisches aus Trifluormethan (CHF3) und Argon realisiert. Die Bindungsstruktur der Schichten wurden in Abhängigkeit der eingespeisten Leistung, die den Fragmentationsgrad der Monomere im Plasma bestimmt, analysiert. Hierzu wurden die Röntgen-Photoelektronenspektroskopie (XPS), Rasterkraftmikroskopie (AFM), Flugzeit-Sekundärionenmassenspektrometrie (ToF-SIMS) und Röntgenreflektometrie (XRR) eingesetzt. Es zeigte sich, dass die abgeschiedenen Schichten ein homogenes Wachstumsverhalten und keine ausgeprägten Interfacebereiche zum Substrat und zur Oberfläche hin aufweisen. Die XPS-Analysen deuten darauf hin, dass Verkettungsreaktionen von CF2-Radikalen im Plasma eine wichtige Rolle für den Schichtbildungsprozess spielen. Weiterhin konnte gezeigt werden, dass der gewählte Beschichtungsprozess eine gezielte Reduzierung der Benetzbarkeit verschiedener Substrate ermöglicht. Dabei genügen Schichtdicken von weniger als 3 nm zur Erreichung eines teflonartigen Oberflächencharakters mit Oberflächenenergien um 20 mN/m. Damit erschließen sich neue Applikationsmöglichkeiten ultra-dünner Fluorkohlenstoffschichten, was anhand eines Beispiels aus dem Bereich der Nanooptik demonstriert wird. Für die siliziumorganischen Schichten unter Verwendung des Monomers Hexamethyldisiloxan (HMDSO) galt es zunächst, diejenigen Prozessparameter zu identifizieren, die ihren organischen bzw. glasartigen Charakter bestimmen. Hierzu wurde der Einfluss von Leistungseintrag und Zugabe von Sauerstoff als Reaktivgas auf die Elementzusammensetzung der Schichten untersucht. Bei niedrigen Plasmaleistungen und Sauerstoffflüssen werden vor allem kohlenstoffreiche Schichten abgeschieden, was auf eine geringere Fragmentierung der Kohlenwasserstoffgruppen zurückgeführt wurde. Es zeigte sich, dass die Variation des Sauerstoffanteils im Prozessgas eine sehr genaue Steuerbarkeit der Schichteigenschaften ermöglicht. Mittels Sekundär-Neutralteilchen-Massenspektrometrie (SNMS) konnte die prozesstechnische Realisierbarkeit und analytische Quantifizierbarkeit von Wechselschichtsystemen aus polymerartigen und glasartigen Lagen demonstriert werden. Aus dem Intensitätsverhältnis von Si:H-Molekülen zu Si-Atomen im SNMS-Spektrum ließ sich der Wasserstoffgehalt bestimmen. Weiterhin konnte gezeigt werden, dass durch Abscheidung von HMDSO-basierten Gradientenschichten eine deutliche Reduzierung von Reibung und Verschleiß bei Elastomerbauteilen erzielt werden kann.

Structure property relations in complex copolymer systems

A thorough investigation was made of the structure-property relation of well-defined statistical, gradient and block copolymers of various compositions. Among the copolymers studied were those which were synthesized using isobornyl acrylate (IBA) and n-butyl acrylate (nBA) monomer units. The copolymers exhibited several unique properties that make them suitable materials for a range of applications. The thermomechanical properties of these new materials were compared to acrylate homopolymers. By the proper choice of the IBA/nBA monomer ratio, it was possible to tune the glass transition temperature of the statistical P(IBA-co-nBA) copolymers. The measured Tg’s of the copolymers with different IBA/nBA monomer ratios followed a trend that fitted well with the Fox equation prediction. While statistical copolymers showed a single glass transition (Tg between -50 and 90 ºC depending on composition), DSC block copolymers showed two Tg’s and the gradient copolymer showed a single, but very broad, glass transition. PMBL-PBA-PMBL triblock copolymers of different composition ratios were also studied and revealed a microphase separated morphology of mostly cylindrical PMBL domains hexagonally arranged in the PBA matrix. DMA studies confirmed the phase separated morphology of the copolymers. Tensile studies showed the linear PMBL-PBA-PMBL triblock copolymers having a relatively low elongation at break that was increased by replacing the PMBL hard blocks with the less brittle random PMBL-r-PMMA blocks. The 10- and 20-arm PBA-PMBL copolymers which were studied revealed even more unique properties. SAXS results showed a mixture of cylindrical PMBL domains hexagonally arranged in the PBA matrix, as well as lamellar. Despite PMBL’s brittleness, the triblock and multi-arm PBA-PMBL copolymers could become suitable materials for high temperature applications due to PMBL’s high glass transition temperature and high thermal stability. The structure-property relation of multi-arm star PBA-PMMA block copolymers was also investigated. Small-angle X-ray scattering revealed a phase separated morphology of cylindrical PMMA domains hexagonally arranged in the PBA matrix. DMA studies found that these materials possess typical elastomeric behavior in a broad range of service temperatures up to at least 250°C. The ultimate tensile strength and the elastic modulus of the 10- and 20-arm star PBA-PMMA block copolymers are significantly higher than those of their 3-arm or linear ABA type counterparts with similar composition, indicating a strong effect of the number of arms on the tensile properties. Siloxane-based copolymers were also studied and one of the main objectives here was to examine the possibility to synthesize trifluoropropyl-containing siloxane copolymers of gradient distribution of trifluoropropyl groups along the chain. DMA results of the PDMS-PMTFPS siloxane copolymers synthesized via simultaneous copolymerization showed that due to the large difference in reactivity rates of 2,4,6-tris(3,3,3-trifluoropropyl)-2,4,6-trimethylcyclotrisiloxane (F) and hexamethylcyclotrisiloxane (D), a copolymer of almost block structure containing only a narrow intermediate fragment with gradient distribution of the component units was obtained. A more dispersed distribution of the trifluoropropyl groups was obtained by the semi-batch copolymerization process, as the DMA results revealed more ‘‘pure gradient type’’ features for the siloxane copolymers which were synthesized by adding F at a controlled rate to the polymerization of the less reactive D. As with trifluoropropyl-containing siloxane copolymers, vinyl-containing polysiloxanes may be converted to a variety of useful polysiloxane materials by chemical modification. But much like the trifluoropropyl-containing siloxane copolymers, as a result of so much difference in the reactivities between the component units 2,4,6-trivinyl-2,4,6-trimethylcyclotrisiloxane (V) and hexamethylcyclotrisiloxane (D), thermal and mechanical properties of the PDMS-PMVS copolymers obtained by simultaneous copolymerization was similar to those of block copolymers. Only the copolymers obtained by semi-batch method showed properties typical for gradient copolymers.

Functional silicones and silicone-containing block copolymers

Polysiloxanes can be synthesized and subsequently modified (i) by the attachment of small molecules that change the properties of the silicone in such a way that it becomes more hydrophilic, but under the premise that this does not go together with a loss of the silicone-specific features. This can be done by adding hydrophilic sidechains to a polysiloxane. Polyethers like poly(ethylene glycol) or hyperbranched polyether-polyols are suitable in this regard. In order to assure that the silicone properties retain, these side groups can be attached to only one part of the polysiloxane backbone, which results in a block copolymer that consists of a common polysiloxane and a second block of the modified structure. (ii) Polysiloxanes can be equipped with functional groups that are capable of initializing polymerization of a different monomer (macroinitiator approach). For example, hydroxyl groups are used to initiate the ring opening polymerization of cyclic esters, or ATRP macroinitiators can be synthesized to add a second block via controlled radical polymerization. Stimuli responsive polymers like poly(oligoethylene glycol methacrylate) (POEGMA) can be added via this route to create “smart” siloxane-containing block copolymers that respond to certain stimuli. rnAn important premise for all synthetic routes is to achieve the targeted structure in a process as simple as possible, because facile availability of the material is crucial with regard to industrial applicability of the invented products. rnConcerning characterization of the synthesized macromolecules, emphasize is put on their (temperature dependent) aggregation behavior, which can be investigated by several microscopic and scattering methods, their behavior at the interface between silicone oils and water and their thermal properties.rnrn

Eliminating Adhesion Errors in Nanoindentation of Compliant Polymers and Hydrogels

Nanoindentation is a valuable tool for characterization of biomaterials due to its ability to measure local properties in heterogeneous, small or irregularly shaped samples. However, applying nanoindentation to compliant, hydrated biomaterials leads to many challenges including adhesion between the nanoindenter tip and the sample. Although adhesion leads to overestimation of the modulus of compliant samples when analyzing nanoindentation data using traditional analysis techniques, most studies of biomaterials have ignored its effects. This paper demonstrates two methods for managing adhesion in nanoindentation analysis, the nano-JKR force curve method and the surfactant method, through application to two biomedically-relevant compliant materials, poly(dimethyl siloxane) (PDMS) elastomers and poly(ethylene glycol) (PEG) hydrogels. The nano-JKR force curve method accounts for adhesion during data analysis using equations based on the Johnson-Kendall-Roberts (JKR) adhesion model, while the surfactant method eliminates adhesion during data collection, allowing data analysis using traditional techniques. In this study, indents performed in air or water resulted in adhesion between the tip and the sample, while testing the same materials submerged in Optifree Express() contact lens solution eliminated tip-sample adhesion in most samples. Modulus values from the two methods were within 7% of each other, despite different hydration conditions and evidence of adhesion. Using surfactant also did not significantly alter the properties of the tested material, allowed accurate modulus measurements using commercial software, and facilitated nanoindentation testing in fluids. This technique shows promise for more accurate and faster determination of modulus values from nanoindentation of compliant, hydrated biological samples. Copyright 2013 Elsevier Ltd. All rights reserved.

Multi-software modeling technique for field distribution propagation through an optical vertical interconnect assembly

Embedded siloxane polymer waveguides have shown promising results for use in optical backplanes. They exhibit high temperature stability, low optical absorption, and require common processing techniques. A challenging aspect of this technology is out-of-plane coupling of the waveguides. A multi-software approach to modeling an optical vertical interconnect (via) is proposed. This approach utilizes the beam propagation method to generate varied modal field distribution structures which are then propagated through a via model using the angular spectrum propagation technique. Simulation results show average losses between 2.5 and 4.5 dB for different initial input conditions. Certain configurations show losses of less than 3 dB and it is shown that in an input/output pair of vias, average losses per via may be lower than the targeted 3 dB.