Albuterol delivery in an in vitro pediatric ventilator lung model: comparison of jet, ultrasonic, and mesh nebulizers.

OBJECTIVE: : To determine the influence of nebulizer types and nebulization modes on bronchodilator delivery in a mechanically ventilated pediatric lung model. DESIGN: : In vitro, laboratory study. SETTING: : Research laboratory of a university hospital. INTERVENTIONS: : Using albuterol as a marker, three nebulizer types (jet nebulizer, ultrasonic nebulizer, and vibrating-mesh nebulizer) were tested in three nebulization modes in a nonhumidified bench model mimicking the ventilatory pattern of a 10-kg infant. The amounts of albuterol deposited on the inspiratory filters (inhaled drug) at the end of the endotracheal tube, on the expiratory filters, and remaining in the nebulizers or in the ventilator circuit were determined. Particle size distribution of the nebulizers was also measured. MEASUREMENTS AND MAIN RESULTS: : The inhaled drug was 2.8% ± 0.5% for the jet nebulizer, 10.5% ± 2.3% for the ultrasonic nebulizer, and 5.4% ± 2.7% for the vibrating-mesh nebulizer in intermittent nebulization during the inspiratory phase (p < 0.01). The most efficient nebulizer was the vibrating-mesh nebulizer in continuous nebulization (13.3% ± 4.6%, p < 0.01). Depending on the nebulizers, a variable but important part of albuterol was observed as remaining in the nebulizers (jet and ultrasonic nebulizers), or being expired or lost in the ventilator circuit (all nebulizers). Only small particles (range 2.39-2.70 µm) reached the end of the endotracheal tube. CONCLUSIONS: : Important differences between nebulizer types and nebulization modes were seen for albuterol deposition at the end of the endotracheal tube in an in vitro pediatric ventilator-lung model. New aerosol devices, such as ultrasonic and vibrating-mesh nebulizers, were more efficient than the jet nebulizer.

Distortion control for delay-sensitive sources

We investigate the problem of finding minimum-distortion policies for streaming delay-sensitive but distortion-tolerant data. We consider cross-layer approaches which exploit the coupling between presentation and transport layers. We make the natural assumption that the distortion function is convex and decreasing. We focus on a single source-destination pair and analytically find the optimum transmission policy when the transmission is done over an error-free channel. This optimum policy turns out to be independent of the exact form of the convex and decreasing distortion function. Then, for a packet-erasure channel, we analytically find the optimum open-loop transmission policy, which is also independent of the form of the convex distortion function. We then find computationally efficient closed-loop heuristic policies and show, through numerical evaluation, that they outperform the open-loop policy and have near optimal performance.

Laboratory Evaluation of Asphalt-Rubber in Asphalt Paving Mixture, MLR-89-15, 1990

Interest in the use of ground rubber from used tires as a hot asphalt mix binder has been increasing due to the magnitude of the disposal problem posed by the annual addition of millions of waste tires to the refuse stream. This study evaluates, through laboratory means, the performance of asphalt-rubber as a hot mix binder as compared to conventional asphalt. The results indicate that asphalt-rubber outperforms its base asphalt in mixes of identical gradation and comparable void content on tests that are heavily dependent on binder characteristics (resilient modulus and indirect tension). An appreciable increase in rut resistance due to the use of asphalt-rubber is not indicated.

Cities, skills, and regional change

One approach to urban areas emphasizes the existence of certain immutable relationships, such as Zipf's or Gibrat's Law. An alternative view is that urban changereflects individual responses to changing tastes or technologies. This paper examinesalmost 200 years of regional change in the U.S. and finds that few, if any, growth relationships remain constant, including Gibrat's Law. Education does a reasonable jobof explaining urban resilience in recent decades, but does not seem to predict countygrowth a century ago. After reviewing this evidence, we present and estimate a simple model of regional change, where education increases the level of entrepreneurship.Human capital spillovers occur at the city level because skilled workers produce moreproduct varieties and thereby increase labor demand. We find that skills are associatedwith growth in productivity or entrepreneurship, not with growth in quality of life, atleast outside of the West. We also find that skills seem to have depressed housing supplygrowth in the West, but not in other regions, which supports the view that educatedresidents in that region have fought for tougher land-use controls. We also present evidence that skills have had a disproportionately large impact on unemployment duringthe current recession.

Design Process of Packaging Laboratory at Lappeenranta University of Technology

The layout design process of the packaging laboratory at Lappeenranta University of Technology is documented in this thesis. Layout planning methods are discussed in general. The systematic layout planning procedure is presented in more detail as it is utilised in the case of layout planning of the packaging laboratory. General demands for research laboratory are discussed both from the machine and product perspectives. The possibilities for commercial food processing in the laboratory are discussed from the point of view of foodstuff processing regulations and hygiene demands. The layout planning process is documented and different layout possibilities are presented. Different layout drafts are evaluated and one layout draft is developed to be the final layout of the packaging laboratory. Guideline for technical planning and implementation based on the final layout is given

La investigación regional en España. Rankings de países, instituciones y autores en ciencia regional y urbana para el período 1991-2000

Este trabajo analiza cual ha sido la evolución de la investigación en ciencia regional y urbana en España en el período 1991-2000 situándola en el contexto internacional. Para ello, se elaboran rankings de países, autores e instituciones en función de las publicaciones realizadas en una muestra de nueve revistas internacionales ampliamente reconocidas dentro de este campo. Los resultados muestran que la mejora en la posición relativa a nivel internacional encontrada por otros autores para el conjunto de la investigación española en economía también se produce en el contexto de la investigación económica regional y urbana De hecho, hay un claro aumento de la presencia a nivel internacional de los autores e instituciones españolas motivado en buena medida por un incremento de las publicaciones de autores con tradición en la investigación en ciencia regional y urbana pero también por la irrupción con fuerza de 'nuevos' autores.

Governments and the Decentralization

The Purpose of This Article Is to Show How Costs and Benefits of Geographical Decentralization of R&D Can Be Identified and Compared. the Benefits for the Region That Receives R&D Activities Are Studied in Section 1. They Stem From the Short-Run Multiplier Effect, the Amelioration of Human Capital and the Possible Modernization of the Local Industrial Structure. on the Cost Side Examined in Section 2, the Observable Impacts of the Decentralization of R&D Concern the Loss of Returns to Scale and of the Production of the R&D Output. It Is Shown, in Section 3, That the Flows of Costs and Benefits Must Be Discounted by the Social Cost of Capital. the Main Conclusion of This Article Is That the Decentralization of R&D in a Large Sparsely Populated Country Entails Social Cost and Would Weaken Its Competitive Position in World Commerce. on the Other Hand, the Issue of Decentralization Is More Crucial for Small Countries (In Terms of Population and Economic Size) Than for Large Ones, Like the U.S., Where Critical Masses of Research Efforts Cna Be Simulataneously Attained in Many Fields and in Many Places.

Providing Genetic Testing Through the Private Sector: A View From Canada

Genetic testing technologies are rapidly moving from the research laboratory to the market place. Very little scholarship considers the implications of private genetic testing for a public health care system such as Canada’s. It is critical to consider how and if these tests should be marketed to, and purchased by, the public. It is also imperative to evaluate the extent to which genetic tests are or should be included in Canada’s public health care system, and the impact of allowing a two-tiered system for genetic testing. A series of threshold tests are presented as ways of clarifying whether a genetic test is morally appropriate, effective and safe, efficient and appropriate for public funding and whether private purchase poses special problems and requires further regulation. These thresholds also identify the research questions around which professional, public and policy debate must be sustained: What is a morally acceptable goal for genetic services? What are the appropriate benefits? What are the risks? When is it acceptable that services are not funded under health care? And how can the harms of private access be managed?

Preparation, Characterisation And Microwave Dielectric Properties Of Anbn-1o3n (N=5,6,8) Type Perovskite Compounds

The present study on the preparation , characterization and microwave dielectric properties of AnBn-1O3n (N=5,6,8) type perovskite compounds. The explored ceramics show dielectric constant between 11 and 54,quality factor in the range 2400 to 88900 GHz and Tf in the range -73 to +231ppm/0C.Most of the investigated cation deficient hexagonal perovskites show intermediate dielectric constant with high quality factors. This study gives a general introduction about material, scientific and technological aspects of DRs.Three important ,€r ,Q and Tf, used for the DR characterization are described. The relationship of the above parameters with the fundamental material characteristics is discussed. Different modes are excited when a DR is excited with suitable microwave spectrum of frequencies .A description of analytical determination of frequencies and construction of mode charts used for sample design and mode identification are also discussed. In this study several ceramics are developed for DR purposes, very little attention has been paid to grow the single crystals. It might be due to the fact that the difficulties and time involved in the growth of single crystals, big enough to function as microwave resonators make them expensive .However single crystals of these materials may have very high Q values. It is also possible that a better understanding of the dielectric properties in relation to the structure can be arrived using single crystals. Hence one of the future directions of dielectric resonator research should be to grow good quality single crystals of the above materials.

Tailored Ion Imprinted Polymer Materials for the Preconcentrative Separation of Noble Metals

Tailored ion imprinted polymer materials for the preconcentrative separation of noble metals. This study deals with the synthesis, separation,characterization and analytical application of the noble metals especially palladium and platinum. Platinum group metals(PGM) are currently receiving world wide attention. This group include Palladium(Pt),rhodium(Rh), ruthenium(Ru), iridium(Ir) and osmium(Os).PGM are used as catalysts for a wide variety of hydrogenation, oxidation, isomerization,cyclization,dehydrogenation and dehalogenation reactions.The corrosion resistance of PGM enables them to use in jewellery,electrical and glass industries,extrusion of synthetic fibres,manufacture of laboratory utensils,dental and medical devices. This study clearly establishes selective recovery of platinum from other noble and transition elements.

OFFLINE AND ONLINE SOLID PHASE EXTRACTION/PRECONCENTRATION OF INORGANICS

Solid phase extraction (SPE) is a powerful technique for preconcentration/removal or separation of trace and ultra trace amounts of toxic and nutrient elements. SPE effectively simplifies the labour intensive sample preparation, increase its reliability and eliminate the clean up step by using more selective extraction procedures. The synthesis of sorbents with a simplified procedure and diminution of the risks of errors shows the interest in the areas of environmental monitoring, geochemical exploration, food, agricultural, pharmaceutical, biochemical industry and high purity metal designing, etc. There is no universal SPE method because the sample pretreatment depends strongly on the analytical demand. But there is always an increasing demand for more sensitive, selective, rapid and reliable analytical procedures. Among the various materials, chelate modified naphthalene, activated carbon and chelate functionalized highly cross linked polymers are most important. In the biological and environmental field, large numbers of samples are to be analysed within a short span of time. Hence, online flow injection methods are preferred as they allow extraction, separation, identification and quantification of many numbers of analytes. The flow injection online preconcentration flame AAS procedure developed allows the determination of as low as 0.1 µg/l of nickel in soil and cobalt in human hair samples. The developed procedure is precise and rapid and allows the analysis of 30 samples per hour with a loading time of 60 s. The online FI manifold used in the present study permits high sampling, loading rates and thus resulting in higher preconcentration/enrichment factors of -725 and 600 for cobalt and nickel respectively with a 1 min preconcentration time compared to conventional FAAS signal. These enrichment factors are far superior to hitherto developed on line preconcentration procedures for inorganics. The instrumentation adopted in the present study allows much simpler equipment and low maintenance costs compared to costlier ICP-AES or ICP-MS instruments.

Novel Strategies for Heterocyclic Constructions via 1, 4-Dipolar Intermediates

In the thesis entitled " Novel Strategies for Heterocyclic Constructions via 1 ,4-Dipolar Intermediates"Synthesis of a complex organic molecules essentially involves the formation of carbon-carbon and carbon-heteroatom bonds. Various synthetic methods are available for these processes involving ionic, pericyclic and radical reactions. Among the pericyclic reactions, dipolar cycloaddition reactions, introduced by Huisgen, have emerged as a very powerful tool for heterocyclic construction. Heterocyclic compounds remain an important class of organic molecules due to their natural abundance and remarkable biological activity, thus constituting an intergral part of pharmaceutical industry. In this respect, developing newer synthetic methodology for heterocyclic construction has been an area of immense interest. In recent years, 1,3-dipolar cycloaddition reactions proved to be efficient routes to a wide variety of five membered heterocycles, as attested by their application in the total synthesis of various complex organic molecules. However, the potential application of similar 1,4- dipolar cycloaddition reactions for the construction of six memebered heterocycles remained underexploited. In this context, a systematic investigation of the reactivity of 1,4-dipoles generated from nitrogen heterocycles (pyridine and its analogues) and dimethyl acetylenedicarboxy!ate (DMAD) towards various dipolarophiles has been carried out and the results are embodied.

Production and Characterization of Endocylanase from Bacillus Pumilus Using Solidstate Fermentation and its Application in 'Paper Pulp Processing

In the present studies it is clear that Bacillus pumilus xylanase is having the characteristic suited for an industrial enzyme (xylanases that are active and stable at elevated temperatures and alkaline pH are needed). SSF production of xylanases and its application appears to be an innovative technology where the fermented substrate is the enzyme source that is used directly in the bleaching process without a prior downstream processing. The direct use of SSF enzymes in bleaching is a relatively new biobleaching approach. This can certainly benefit the bleaching process to lower the xylanase production costs and improve the economics and viability of the biobleaching technology. The application of enzymes to the bleaching process has been considered as an environmentally friendly approach that can reduce the negative impact on the environment exerted by the use of chlorine-based bleaching agents. It has been demonstrated that pretreatment of kraft pulp with xylanase prior to bleaching (biobleaching) can facilitate subsequent removal of lignin by bleaching chemicals, thereby, reducing the demand for elemental chlorine or improving final paper brightness. Using this xylanase pre-treatment, has resulted in an increased of brightness (8.5 Unit) when compared to non-enzymatic treated bleached pulp prepared using identical conditions. Reduction of the consumption of active chlorine can be achieved which results in a decrease in the toxicity, colour, chloride and absorbable organic halogen (AOX) levels of bleaching effluents. The xylanase treatment improves drainage, strength properties and the fragility of pulps, and also increases the brightness of pulps. This positive result shows that enzyme pre-treatment facilitates the removal of chromophore fragments of pulp there by making the process more environment friendly

Novel Reactions of TRIS(2-Thienyl)Methane and TRIS(2-Furyal)Methane

A systematic investigation of the reactivity and functionalization of two heterocyclic analogs of triphenylmethane , namely tris(2-thienyl)methane and tris(2-furyl)methane have been carried out and the results are presented in this thesis entitled "NOVEL REACTIONS OF TRIS(2-THIENYL)METHANE AND TRIS(2-FURYL)METHANE.". The history of organic free radicals dates back to Gomberg's monumental discovery of the triphenylmethyl radical in 1900. The heterocyclic analogs of triarylmethane are also interesting from the vantage point of their transformation to the corresponding radicals akin to Gomberg ' s triphenylmethyl radical and also they are prone to further transformation leading to three dimensionally elongated molecules such as dendrimers. Dendritic architectures are one of the most pervasive topologies observed in nature at the macro- and microdimensional length devices. Because of their ability to combine both organic and inorganic compounds and their propensity to either encapsulate or be engineered into unimolecular functional devices , dendrimers are versatile amongst existing nanoscale building blocks and materials.