Improving turbomachinery design process management

It is widely acknowledged that a company's ability to aquire market share, and hence its profitability, is very closely linked to the speed with which it can produce a new design. Indeed, a study by the U.K. Department of Trade and Industry has shown that the critical factor which determines profitability is the timely delivery of the new product. Late entry to market or high production costs dramatically reduce profits whilst an overrun on development cost has little significant effect. This paper describes a method which aims to assist the designer in producing higher performance turbomachinery designs more quickly by accelerating the process by which they are produced. The adopted approach combines an enhanced version of the 'Signposting' design process management methodology with industry-standard analysis codes and Computational Fluid Dynamics (CFD). It has been specifically configured to enable process-wide iteration, near instantaneous generation of guidance data for the designer and fully automatic data handling. A successful laboratory experiment based on the design of a large High Pressure Steam Turbine is described and this leads on to current work which incorporates the extension of the proven concept to a full industrial application for the design of Aeroengine Compressors with Rolls-Royce plc.

Potentials for marine fish hatchery production in Nigeria

The development of fish hatcheries and fish fingerling production in Nigeria has all along concentrated largely on the freshwater fish species without paying enough attention to the more numerous fish species that abound in our coastal/marine environment. This paper, therefore, tries to highlight some basic technologies (in term of design and management) of marine fish hatchery based on the author's experiences in Southeast Asia. Appropriate adaptable technologies for the production of our indigenous species such as the Snappers, Groupers etc. are also discussed. General recommendations are made for marine fish hatchery development in Nigeria

Design, operation and economics of a small-scale hatchery for the larval rearing of sugpo, Penaeus monodon Fab.

One of the major problems in the mass production of sugpo is how to obtain a constant supply of fry. Since ultimately it is the private sector which should produce the sugpo fry to fill the needs of the industry, the Barangay Hatchery Project under the Prawn Program of the Aquaculture Department of SEAFDEC has scaled down the hatchery technology from large tanks to a level which can be adopted by the private sector, especially in the villages, with a minimum of financial and technical inputs. This guide to small-scale hatchery operations is expected to generate more enthusiasm among fish farmers interested in venturing into sugpo culture.

Optimum hot electron production with low-density foams for laser fusion by fast ignition

We propose a foam cone-in-shell target design aiming at optimum hot electron production for the fast ignition. A thin low-density foam is proposed to cover the inner tip of a gold cone inserted in a fuel shell. An intense laser is then focused on the foam to generate hot electrons for the fast ignition. Element experiments demonstrate increased laser energy coupling efficiency into hot electrons without increasing the electron temperature and beam divergence with foam coated targets in comparison with solid targets. This may enhance the laser energy deposition in the compressed fuel plasma.

Design strategies for ultra-high efficiency photovoltaics

While concentrator photovoltaic cells have shown significant improvements in efficiency in the past ten years, once these cells are integrated into concentrating optics, connected to a power conditioning system and deployed in the field, the overall module efficiency drops to only 34 to 36%. This efficiency is impressive compared to conventional flat plate modules, but it is far short of the theoretical limits for solar energy conversion. Designing a system capable of achieving ultra high efficiency of 50% or greater cannot be achieved by refinement and iteration of current design approaches.

This thesis takes a systems approach to designing a photovoltaic system capable of 50% efficient performance using conventional diode-based solar cells. The effort began with an exploration of the limiting efficiency of spectrum splitting ensembles with 2 to 20 sub cells in different electrical configurations. Incorporating realistic non-ideal performance with the computationally simple detailed balance approach resulted in practical limits that are useful to identify specific cell performance requirements. This effort quantified the relative benefit of additional cells and concentration for system efficiency, which will help in designing practical optical systems.

Efforts to improve the quality of the solar cells themselves focused on the development of tunable lattice constant epitaxial templates. Initially intended to enable lattice matched multijunction solar cells, these templates would enable increased flexibility in band gap selection for spectrum splitting ensembles and enhanced radiative quality relative to metamorphic growth. The III-V material family is commonly used for multijunction solar cells both for its high radiative quality and for the ease of integrating multiple band gaps into one monolithic growth. The band gap flexibility is limited by the lattice constant of available growth templates. The virtual substrate consists of a thin III-V film with the desired lattice constant. The film is grown strained on an available wafer substrate, but the thickness is below the dislocation nucleation threshold. By removing the film from the growth substrate, allowing the strain to relax elastically, and bonding it to a supportive handle, a template with the desired lattice constant is formed. Experimental efforts towards this structure and initial proof of concept are presented.

Cells with high radiative quality present the opportunity to recover a large amount of their radiative losses if they are incorporated in an ensemble that couples emission from one cell to another. This effect is well known, but has been explored previously in the context of sub cells that independently operate at their maximum power point. This analysis explicitly accounts for the system interaction and identifies ways to enhance overall performance by operating some cells in an ensemble at voltages that reduce the power converted in the individual cell. Series connected multijunctions, which by their nature facilitate strong optical coupling between sub-cells, are reoptimized with substantial performance benefit.

Photovoltaic efficiency is usually measured relative to a standard incident spectrum to allow comparison between systems. Deployed in the field systems may differ in energy production due to sensitivity to changes in the spectrum. The series connection constraint in particular causes system efficiency to decrease as the incident spectrum deviates from the standard spectral composition. This thesis performs a case study comparing performance of systems over a year at a particular location to identify the energy production penalty caused by series connection relative to independent electrical connection.

On the Role of Delays in Biological Systems : Analysis and Design

This work quantifies the nature of delays in genetic regulatory networks and their effect on system dynamics. It is known that a time lag can emerge from a sequence of biochemical reactions. Applying this modeling framework to the protein production processes, delay distributions are derived in a stochastic (probability density function) and deterministic setting (impulse function), whilst being shown to be equivalent under different assumptions. The dependence of the distribution properties on rate constants, gene length, and time-varying temperatures is investigated. Overall, the distribution of the delay in the context of protein production processes is shown to be highly dependent on the size of the genes and mRNA strands as well as the reaction rates. Results suggest longer genes have delay distributions with a smaller relative variance, and hence, less uncertainty in the completion times, however, they lead to larger delays. On the other hand large uncertainties may actually play a positive role, as broader distributions can lead to larger stability regions when this formalization of the protein production delays is incorporated into a feedback system.

Furthermore, evidence suggests that delays may play a role as an explicit design into existing controlling mechanisms. Accordingly, the reccurring dual-feedback motif is also investigated with delays incorporated into the feedback channels. The dual-delayed feedback is shown to have stabilizing effects through a control theoretic approach. Lastly, a distributed delay based controller design method is proposed as a potential design tool. In a preliminary study, the dual-delayed feedback system re-emerges as an effective controller design.

Impressão de livros sob demanda: o design como ponte entre distintos registros produtivos

A presente dissertação trata de um estudo sobre produção de livros sob demanda em dois momentos distintos da indústria gráfica. Apresentamos uma abordagem histórica do percurso do livro, segundo seus atributos materiais e tecnológicos, que marcaram a transformação de seu caráter fabril de micro e pequena escalas à produção em massa. Ao analisar referências manufatureiras de tiragem limitada do livro no âmbito da impressão tipográfica e digital, observamos o papel que o design é capaz de exercer, representando uma conexão entre esses dois registros técnicos intrinsecamente diferentes. Através da utilização de um modelo descritivo de obras sob o ponto de vista do design gráfico, buscamos pontos de convergência e divergência passíveis de auxiliar na compreensão do atual contexto de transição por que passa o mercado editorial.

A contribuição da Metodologia de Projeto em Design no processo de desenvolvimento de recursos de Tecnologia Assistiva

O presente trabalho apresenta o processo utilizado por terapeutas ocupacionais no desenvolvimento de objetos de Tecnologia Assistiva. São apresentadas definições e teorias relacionadas ao desenvolvimento de produtos de Tecnologia Assistiva a qual trata de um grupo de produtos desenvolvidos para pessoas com deficiência. São apresentados: o design de produtos voltados para inclusão, modelos de ações voltados às pessoas com deficiência, princípios para o desenvolvimento de produtos para pessoas com deficiência, o mercado brasileiro e o perfil do público-alvo, e os métodos e técnicas de desenvolvimento de Tecnologia Assistiva. Sendo o terapeuta ocupacional um profissional que no processo de reabilitação desenvolve produtos de Tecnologia Assistiva, explicita-se o seu papel no desenvolvimento desses produtos. Tendo o Ergodesign como base metodológica para o desenvolvimento de produtos de Tecnologia Assistiva, apresentam-se questões pertinentes à essa teoria dentro da ergonomia e do design. Expõem-se os resultados da pesquisa de campo realizada com terapeutas ocupacionais que produzem produtos de Tecnologia Assistiva, com terapeutas ocupacionais que encaminham para outro profissional realizar a produção, com professores de disciplinas de Tecnologia Assistiva dos cursos de Terapia Ocupacional da cidade do Rio de Janeiro e com usuários desses produtos. A partir da pesquisa bibliográfica e dos resultados obtidos na pesquisa de campo, este trabalho tem como objetivo principal contribuir, através de uma proposta metodológica, para a formação do terapeuta ocupacional no processo de desenvolvimento de objetos para pessoas com deficiência

Advanced Reaction Systems for Hydrogen Production

[EN] This PhD work started in March 2010 with the support of the University of the Basque Country (UPV/EHU) under the program named “Formación de Personal Investigador” at the Chemical and Environmental Engineering Department in the Faculty of Engineering of Bilbao. The major part of the Thesis work was carried out in the mentioned department, as a member of the Sustainable Process Engineering (SuPrEn) research group. In addition, this PhD Thesis includes the research work developed during a period of 6 months at the Institut für Mikrotechnik Mainz GmbH, IMM, in Germany. During the four years of the Thesis, conventional and microreactor systems were tested for several feedstocks renewable and non-renewable, gases and liquids through several reforming processes in order to produce hydrogen. For this purpose, new catalytic formulations which showed high activity, selectivity and stability were design. As a consequence, the PhD work performed allowed the publication of seven scientific articles in peer-reviewed journals. This PhD Thesis is divided into the following six chapters described below. The opportunity of this work is established on the basis of the transition period needed for moving from a petroleum based energy system to a renewable based new one. Consequently, the present global energy scenario was detailed in Chapter 1, and the role of hydrogen as a real alternative in the future energy system was justified based on several outlooks. Therefore, renewable and non-renewable hydrogen production routes were presented, explaining the corresponding benefits and drawbacks. Then, the raw materials used in this Thesis work were described and the most important issues regarding the processes and the characteristics of the catalytic formulations were explained. The introduction chapter finishes by introducing the concepts of decentralized production and process intensification with the use of microreactors. In addition, a small description of these innovative reaction systems and the benefits that entailed their use were also mentioned. In Chapter 2 the main objectives of this Thesis work are summarized. The development of advanced reaction systems for hydrogen rich mixtures production is the main objective. In addition, the use and comparison between two different reaction systems, (fixed bed reactor (FBR) and microreactor), the processing of renewable raw materials, the development of new, active, selective and stable catalytic formulations, and the optimization of the operating conditions were also established as additional partial objectives. Methane and natural gas (NG) steam reforming experimental results obtained when operated with microreactor and FBR systems are presented in Chapter 3. For these experiments nickel-based (Ni/Al2O3 and Ni/MgO) and noble metal-based (Pd/Al2O3 and Pt/Al2O3) catalysts were prepared by wet impregnation and their catalytic activity was measured at several temperatures, from 973 to 1073 K, different S/C ratios, from 1.0 to 2.0, and atmospheric pressure. The Weight Hourly Space Velocity (WHSV) was maintained constant in order to compare the catalytic activity in both reaction systems. The results obtained showed a better performance of the catalysts operating in microreactors. The Ni/MgO catalyst reached the highest hydrogen production yield at 1073 K and steam-to-carbon ratio (S/C) of 1.5 under Steam methane Reforming (SMR) conditions. In addition, this catalyst also showed good activity and stability under NG reforming at S/C=1.0 and 2.0. The Ni/Al2O3 catalyst also showed high activity and good stability and it was the catalyst reaching the highest methane conversion (72.9 %) and H2out/CH4in ratio (2.4) under SMR conditions at 1073 K and S/C=1.0. However, this catalyst suffered from deactivation when it was tested under NG reforming conditions. Regarding the activity measurements carried out with the noble metal-based catalysts in the microreactor systems, they suffered a very quick deactivation, probably because of the effects attributed to carbon deposition, which was detected by Scanning Electron Microscope (SEM). When the FBR was used no catalytic activity was measured with the catalysts under investigation, probably because they were operated at the same WHSV than the microreactors and these WHSVs were too high for FBR system. In Chapter 4 biogas reforming processes were studied. This chapter starts with an introduction explaining the properties of the biogas and the main production routes. Then, the experimental procedure carried out is detailed giving concrete information about the experimental set-up, defining the parameters measured, specifying the characteristics of the reactors used and describing the characterization techniques utilized. Each following section describes the results obtained from activity testing with the different catalysts prepared, which is subsequently summarized: Section 4.3: Biogas reforming processes using γ-Al2O3 based catalysts The activity results obtained by several Ni-based catalysts and a bimetallic Rh-Ni catalyst supported on magnesia or alumina modified with oxides like CeO2 and ZrO2 are presented in this section. In addition, an alumina-based commercial catalyst was tested in order to compare the activity results measured. Four different biogas reforming processes were studied using a FBR: dry reforming (DR), biogas steam reforming (BSR), biogas oxidative reforming (BOR) and tri-reforming (TR). For the BSR process different steam to carbon ratios (S/C) from 1.0 to 3.0, were tested. In the case of BOR process the oxygen-to-methane (O2/CH4) ratio was varied from 0.125 to 0.50. Finally, for TR processes different S/C ratios from 1.0 to 3.0, and O2/CH4 ratios of 0.25 and 0.50 were studied. Then, the catalysts which achieved high activity and stability were impregnated in a microreactor to explore the viability of process intensification. The operation with microreactors was carried out under the best experimental conditions measured in the FBR. In addition, the physicochemical characterization of the fresh and spent catalysts was carried out by Inductively Coupled Plasma Atomic Emission Spectroscopy (ICP-AES), N2 physisorption, H2 chemisorption, Temperature Programmed Reduction (TPR), SEM, X-ray Photoelectron Spectroscopy (XPS) and X-ray powder Diffraction (XRD). Operating with the FBR, conversions close to the ones predicted by thermodynamic calculations were obtained by most of the catalysts tested. The Rh-Ni/Ce-Al2O3 catalyst obtained the highest hydrogen production yield in DR. In BSR process, the Ni/Ce-Al2O3 catalyst achieved the best activity results operating at S/C=1.0. In the case of BOR process, the Ni/Ce-Zr-Al2O3 catalyst showed the highest reactants conversion values operating at O2/CH4=0.25. Finally, in the TR process the Rh-Ni/Ce-Al2O3 catalyst obtained the best results operating at S/C=1.0 and O2/CH4=0.25. Therefore, these three catalysts were selected to be coated onto microchannels in order to test its performance under BOR and TR processes conditions. Although the operation using microreactors was carried out under considerably higher WHSV, similar conversions and yields as the ones measured in FBR were measured. Furthermore, attending to other measurements like Turnover Frequency (TOF) and Hydrogen Productivity (PROD), the values calculated for the catalysts tested in microreactors were one order of magnitude higher. Thus, due to the low dispersion degree measured by H2-chemisorption, the Ni/Ce-Al2O3 catalyst reached the highest TOF and PROD values. Section 4.4: Biogas reforming processes using Zeolites L based catalysts In this section three type of L zeolites, with different morphology and size, were synthesized and used as catalyst support. Then, for each type of L zeolite three nickel monometallic and their homologous Rh-Ni bimetallic catalysts were prepared by the wetness impregnation method. These catalysts were tested using the FBR under DR process and different conditions of BSR (S/C ratio of 1.0 and 2.0), BOR (O2/CH4 ratio of 0.25 and 0.50) and TR processes (at S/C=1.0 and O2/CH4=0.25). The characterization of these catalysts was also carried out by using the same techniques mentioned in the previous section. Very high methane and carbon dioxide conversion values were measured for almost all the catalysts under investigation. The experimental results evidenced the better catalytic behavior of the bimetallic catalysts as compared to the monometallic ones. Comparing the catalysts behavior with regards to their morphology, for the BSR process the Disc catalysts were the most active ones at the lowest S/C ratio tested. On the contrary, the Cylindrical (30–60 nm) catalysts were more active under BOR conditions at O2/CH4=0.25 and TR processes. By the contrary, the Cylindrical (1–3 µm) catalysts showed the worst activity results for both processes. Section 4.5: Biogas reforming processes using Na+ and Cs+ doped Zeolites LTL based catalysts A method for the synthesis of Linde Type L (LTL) zeolite under microwave-assisted hydrothermal conditions and its behavior as a support for heterogeneously catalyzed hydrogen production is described in this section. Then, rhodium and nickel-based bimetallic catalysts were prepared in order to be tested by DR process and BOR process at O2/CH4=0.25. Moreover, the characterization of the catalysts under investigation was also carried out. Higher activities were achieved by the catalysts prepared from the non-doped zeolites, Rh-Ni/D and Rh-Ni/N, as compared to the ones supported on Na+ and Cs+ exchanged supports. However, the differences between them were not very significant. In addition, the Na+ and Cs+ incorporation affected mainly to the Disc catalysts. Comparing the results obtained by these catalysts with the ones studied in the section 4.4, in general worst results were achieved under DR conditions and almost the same results when operated under BOR conditions. In Chapter 5 the ethylene glycol (EG) as feed for syngas production by steam reforming (SR) and oxidative steam reforming (OSR) was studied by using microchannel reactors. The product composition was determined at a S/C of 4.0, reaction temperatures between 625°C and 725°C, atmospheric pressure and Volume Hourly Space Velocities (VHSV) between 100 and 300 NL/(gcath). This work was divided in two sections. The first one corresponds to the introduction of the main and most promising EG production routes. Then, the new experimental procedure is detailed and the information about the experimental set-up and the measured parameters is described. The characterization was carried out using the same techniques as for the previous chapter. Then, the next sections correspond to the catalytic activity and catalysts characterization results. Section 5.3: xRh-cm and xRh-np catalysts for ethylene glycol reforming Initially, catalysts with different rhodium loading, from 1.0 to 5.0 wt. %, and supported on α-Al2O3 were prepared by two different preparation methods (conventional impregnation and separate nanoparticle synthesis). Then, the catalysts were compared regarding their measured activity and selectivity, as well as the characterization results obtained before and after the activity tests carried out. The samples prepared by a conventional impregnation method showed generally higher activity compared to catalysts prepared from Rh nanoparticles. By-product formation of species such as acetaldehyde, ethane and ethylene was detected, regardless if oxygen was added to the feed or not. Among the catalysts tested, the 2.5Rh-cm catalyst was considered the best one. Section 5.4: 2.5Rh-cm catalyst support modification with CeO2 and La2O3 In this part of the Chapter 5, the catalyst showing the best performance in the previous section, the 2.5Rh-Al2O3 catalyst, was selected in order to be improved. Therefore, new Rh based catalysts were designed using α-Al2O3 and being modified this support with different contents of CeO2 or La2O3 oxides. All the catalysts containing additives showed complete conversion and selectivities close to the equilibrium in both SR and OSR processes. In addition, for these catalysts the concentrations measured for the C2H4, CH4, CH3CHO and C2H6 by-products were very low. Finally, the 2.5Rh-20Ce catalyst was selected according to its catalytic activity and characterization results in order to run a stability test, which lasted more than 115 hours under stable operation. The last chapter, Chapter 6, summarizes the main conclusions achieved throughout this Thesis work. Although very high reactant conversions and rich hydrogen mixtures were obtained using a fixed bed reaction system, the use of microreactors improves the key issues, heat and mass transfer limitations, through which the reforming reactions are intensified. Therefore, they seem to be a very interesting and promising alternative for process intensification and decentralized production for remote application.

Pioneiros do design brasileiro no projeto de automóveis

Não se questiona que o design seja um saber naturalmente multidisciplinar. Os projetos da indústria automobilística ilustram esse ponto magistralmente: do ato de inventar à engenharia da produção; do design de exteriores aos interiores; das autopeças às diversas tintas. Projetos desenvolvidos em engenharia simultânea, produzidos em diversos países do mundo e montados onde quer que se mostre mais rentável. A moderna indústria automobilística mostra-se, nesse sentido, global. Mas como harmonizar os gostos e as legislações locais a essa estrutura produtiva internacional? Esta dissertação ilustra alguns aspectos da estratégia de projetos em design automobilístico tomando como base a experiência brasileira. Foram entrevistados os mais destacados designers brasileiros de automóveis dos pioneiros aos mais importantes profissionais contemporâneos. Embora as estratégias das empresas sejam diversas fato que impede uma única conclusão -, esta dissertação lança luzes sobre os desafios do desenvolvimento de projetos automobilísticos onde o projeto é global mas as vendas são locais.

Latt-Mayer, um estudo de caso: tecnologia na história do design gráfico brasileiro.

Nosso objetivo neste trabalho é investigar como o design gráfico se relaciona com os meios de produção da indústria gráfica brasileira. Não é comum encontrar referências abordando temas que relacionam design e tecnologia em livros sobre a história do Brasil, o que demonstra a urgência do resgate histórico de indústrias que implementaram novas tecnologias para atender a demandas projetuais e mercadológicas. Sediada na cidade do Rio de Janeiro, a clicheria Latt-Mayer como era comumente chamada, era sinônimo de qualidade e tecnologia. Entre seus clientes podemos apontar agências de publicidade, editoras, escritórios de designers e gráficas de todo país. Esta pesquisa se baseia em um corpus composto por imagens, documentos, manuais técnicos, reportagens, matrizes e depoimentos com pessoas que estiveram diretamente envolvidas com essa empresa. Catalogamos maquinaria e técnicas utilizadas, além de projetos gráficos relevantes que tiveram matrizes e provas produzidas na empresa. Por meio deste trabalho, é possível visualizar um abrangente painel histórico, que contempla um período em que ocorreram significativas transformações na relação entre designers e tecnologia na indústria gráfica brasileira.

Design à mostra: o projeto de museus temáticos

O objetivo desse trabalho é compreender como o design é utilizado no espaço expositivo para construir contexto, conteúdo e linguagem. Entender quais estratégias são usadas para projetar ambientes atraentes à visitação em vista a proporcionar experiências coletivas e individuais, contemplativas, espaciais (imersivas), sensoriais e interativas. Para tal analisamos a mudança do papel dos museus ao longo do tempo e montamos um panorama das instituições museológicas no Brasil nas últimas décadas. Selecionamos padrões de exibição instituídos historicamente em termos mundiais, já que o Brasil sofreu enorme influência cultural da Europa e dos Estados Unidos. Estabelecemos uma base de conceitos que envolvem a linguagem do projeto de exposições e museus temáticos, considerando aspectos como formas de aprendizagem do público, comportamento deste em relação ao objeto exposto, produção de conteúdo, produção de sentido, escolha de linguagem, intencionalidade, construção de experiência, mediação e interface. Analisamos como estudo de caso, o projeto de dois museus temáticos contemporâneos, o Museu da Língua Portuguesa e o Museu do Futebol, com a intenção de construir uma crítica ao projeto espacial-visual, entendendo as relações estabelecidas entre os objetos (previamente existentes ou projetados produtos, textos, imagens, vídeos), a forma como eles são expostos e as características do local escolhido para abrigar a exposição.

Design à mostra: o projeto de museus temáticos

O objetivo desse trabalho é compreender como o design é utilizado no espaço expositivo para construir contexto, conteúdo e linguagem. Entender quais estratégias são usadas para projetar ambientes atraentes à visitação em vista a proporcionar experiências coletivas e individuais, contemplativas, espaciais (imersivas), sensoriais e interativas. Para tal analisamos a mudança do papel dos museus ao longo do tempo e montamos um panorama das instituições museológicas no Brasil nas últimas décadas. Selecionamos padrões de exibição instituídos historicamente em termos mundiais, já que o Brasil sofreu enorme influência cultural da Europa e dos Estados Unidos. Estabelecemos uma base de conceitos que envolvem a linguagem do projeto de exposições e museus temáticos, considerando aspectos como formas de aprendizagem do público, comportamento deste em relação ao objeto exposto, produção de conteúdo, produção de sentido, escolha de linguagem, intencionalidade, construção de experiência, mediação e interface. Analisamos como estudo de caso, o projeto de dois museus temáticos contemporâneos, o Museu da Língua Portuguesa e o Museu do Futebol, com a intenção de construir uma crítica ao projeto espacial-visual, entendendo as relações estabelecidas entre os objetos (previamente existentes ou projetados produtos, textos, imagens, vídeos), a forma como eles são expostos e as características do local escolhido para abrigar a exposição.

Klaxon, Base, Noigrandes : o design das revistas brasileiras de vanguarda

As revistas Klaxon, base e Noigandres são exemplos de revistas de vanguarda em que o design gráfico foi usado como instrumento para a expressão de idéias, compartilhadas pelos grupos artísticos envolvidos em sua publicação. São marcos do design moderno, encaixando-se no conceito de produto erudito (Bourdieu), destinado não ao grande público, mas a grupos de pares, que compartilhavam os valores estéticos e as ambições à condição de vanguarda em seus respectivos domínios artísticos. Estas revistas são expoentes do campo do design gráfico moderno, que só viria a se institucionalizar na década de 60, com a criação da ESDI e o surgimento do movimento concretista nas artes plásticas.