A comparison of thermal condition between pilot- and full-scale furnaces for studying slagging and fouling propensity in PF boilers

The Australian Coal Industry Research Laboratory (ACIRL) furnace is scaled to simulate slagging and fouling in operating boilers. This requires that the gas and target temperatures, the heat flux, and the flow pattern be the same as those in real boilers. The gas and target temperatures are maintained by insulating the wall and cooling the target respectively. The flow pattern of a small burner cannot be the same as a large furnace. However, this flow pattern is partially compensated for by placing the slagging panels in three vertical locations. The paper develops the models of radiant heat transfer from the flame to the deposits both in pilot-scale and full-scale furnaces. They are used to compare the effective radiant heat transfer of the pilot- and full-scale furnaces. The experimental data both from the pilot- and full-scale furnaces are used to verify the incident heat flux and temperature profiles in the pilot- and full-scale furnaces. The results showed that the thermal condition in the pilot-scale furnace meets the requirements for studying the slagging regarding the gas temperature and the incident heat flux, particularly for the panel #1. The gas temperature in the convective section also meets the requirement for studying the fouling.

An ATP-sensitive K+ conductance in dissociated neurones from adult rat intracardiac ganglia

1. An ATP-sensitive K+ (K-ATP) conductance has been identified using the perforated patch recording configuration in a population (52%) of dissociated neurones from adult rat intracardiac ganglia. The presence of the sulphonylurea receptor in approximately half of the intracardiac neurones was confirmed by labelling with fluorescent glibenclamide-BODIPY. 2. Under current clamp conditions in physiological solutions, leveromakalim (10 muM) evoked a hyperpolarization, which was inhibited by the sulphonylurea drugs glibenclamide and tolbutamide. 3. Under voltage clamp conditions in symmetrical (140 mM) K+ solutions, hath application of levcromakalim evoked an inward current with a density of similar to8 pA pF(-1) at -50 mV and a slope conductance of similar to9 nS, which reversed close to the potassium equilibrium potential (E-K). Cell dialysis with an ATP-free intracellular solution also evoked an inward current, which was inhibited by tolbutamide. 4. Bath application of either glibenclamide (10 muM) or tolbutamide (100 muM) depolarized adult intracardiac neurones by 3-5 mV, suggesting that a K-ATP conductance is activated under resting conditions and contributes to the resting membrane potential. 5. Activation of a membrane current by levcromakalim leas concentration dependent, with an EC50 of 1.6 muM. Inhibition of the levcromakalim-activated current by glibenclamide leas also concentration dependent, with an IC50 of 55 nM. 6. Metabolic inhibition with 2,4-dinitrophenol and iodoacetic acid or superfusion with hypoxic solution (P-O2 similar to 16 mmHg) also activated a membrane current. These currents exhibited similar I-P characteristics to the levcroinakalim-induced current and were inhibited by glibenclamide. 7. Activation of K-ATP channels in mammalian intracardiac neurones may contribute to changes in neural regulation of the mature heart and. cardiac function during ischaemia-reperfusion.

Laparoscopic appendectomy in modern gynecology

Gynecologists frequently manage women with acute or chronic pain in the right iliac fossa. Appendicitis is one of the common conditions encountered in this setting. From the gynecologic perspective, issues regarding the role of laparoscopic appendectomy include radioimaging and laparoscopic diagnosis, operative technique, advantages and disadvantages, and laparoscopic appendectomy in pregnancy and in complicated appendicitis. Most studies are in favor of the procedure, and it seems reasonable to include it in training programs in gynecology.

The effect of latent heat of fusion on heat transfer in fluidized-bed coating of thin plates

This paper presents a numerical study of fluidized-bed coating on thin plates using an orthogonal collocation technique. Inclusion of the latent heat of fusion term in the boundary conditions of the mathematical model accounts for the fact that some polymer powders used in coating may be partially crystalline. Predictions of coating thickness on flat plates were made with actual polymers used in fluidized-bed coating. Reasonably good agreement between numerical predictions of the coating thickness and experimental coating data of Richart was obtained for steel panels preheated to 316 degreesC. A good agreement was also obtained between numerical predictions and our coating thickness data for nylon-11 and polyethylene powders. Predicted coating thickness for polyethylene powder on flat plates were obtained with values of heat transfer coefficient closer to those obtained from our experiments. (C) 2002 Elsevier Science B.V. All rights reserved.

Neural control of the heart: developmental changes in ionic conductances in mammalian intrinsic cardiac neurons

The expression and properties of ionic channels were investigated in dissociated neurons from neonatal and adult rat intracardiac ganglia. Changes in the hyperpolarization-activated and ATP-sensitive K+ conductances during postnatal development and their role in neuronal excitability were examined. The hyperpolarization-activated nonselective cation current, I-h, was observed in all neurons studied and displayed slow time-dependent rectification. An inwardly rectifying K+ current, I-K(I), was present in a population of neurons from adult but not neonatal rats and was sensitive to block by extracellular Ba2+. Using the perforated-patch recording configuration, an ATP-sensitive K+ (K-ATP) conductance was identified in greater than or equal to 50% of intracardiac neurons from adult rats. Levcromakalim evoked membrane hyperpolarization, which was inhibited by the sulphonylurea drugs. glibenclamide and tolbutamide. Exposure to hypoxic conditions also activated a membrane current similar to that induced by levcromakalim and was inhibited by glibenclamide. Changes in the complement of ion channels during postnatal development may underlie observed differences in the function of intracardiac ganglion neurons during maturation. Furthermore, activation of hyperpolarization-activated and KATP channels in mammalian intracardiac neurons may play a role in neural regulation of the mature heart and cardiac function during ischaemia-reperfusion. (C) 2002 Elsevier Science B.V All rights reserved.

A unit cell waveguide model of a reflectarray formed by microstrip patches and slots

An equivalent unit cell waveguide approach (WGA) is described to obtain reflection coefficient phase curves for designing a microstrip patch reflectarray supported by a ground plane with periodic apertures or slots. Based on the presented theory, a computer algorithm for determining the reflection coefficient of a plane wave normally incident on a multi-layer structure of patches and apertures is developed. The validity of the developed algorithm is verified by comparing the obtained results with those published in the literature and the ones generated by Agilent High Frequency Structure Simulator (HFSS). A good agreement in all the presented examples is obtained, proving that the developed theory and computer algorithm can be an effective tool for designing multi-layer microstrip reflectarrays with a periodically perforated ground plane. (C) 2003 Wiley Periodicals, Inc.

Theoretical and experimental studies of unbraced tubular trusses allowing for torsional stiffness

This paper describes the buckling phenomenon of a tubular truss with unsupported length through a full-scale test and presents a practical computational method for the design of the trusses allowing for the contribution of torsional stiffness against buckling, of which the effect has never been considered previously by others. The current practice for the design of a planar truss has largely been based on the linear elastic approach which cannot allow for the contribution of torsional stiffness and tension members in a structural system against buckling. The over-simplified analytical technique is unable to provide a realistic and an economical design to a structure. In this paper the stability theory is applied to the second-order analysis and design of the structural form, with detailed allowance for the instability and second-order effects in compliance with design code requirements. Finally, the paper demonstrates the application of the proposed method to the stability design of a commonly adopted truss system used in support of glass panels in which lateral bracing members are highly undesirable for economical and aesthetic reasons.

Muscarinic and nicotinic ACh receptor activation differentially mobilize Ca2+ in rat intracardiac ganglion neurons

The origin of intracellular Ca2+ concentration ([Ca2+](i)) transients stimulated by nicotinic ( nAChR) and muscarinic ( mAChR) receptor activation was investigated in fura-2-loaded neonatal rat intracardiac neurons. ACh evoked [Ca2+](i) increases that were reduced to similar to 60% of control in the presence of either atropine ( 1 muM) or mecamylamine ( 3 muM) and to < 20% in the presence of both antagonists. Removal of external Ca2+ reduced ACh-induced responses to 58% of control, which was unchanged in the presence of mecamylamine but reduced to 5% of control by atropine. The nAChR-induced [Ca2+](i) response was reduced to 50% by 10 μM ryanodine, whereas the mAChR-induced response was unaffected by ryanodine, suggesting that Ca2+ release from ryanodine-sensitive Ca2+ stores may only contribute to the nAChR-induced [Ca2+](i) responses. Perforated-patch whole cell recording at - 60 mV shows that the rise in [Ca2+](i) is concomitant with slow outward currents on mAChR activation and with rapid inward currents after nAChR activation. In conclusion, different signaling pathways mediate the rise in [Ca2+](i) and membrane currents evoked by ACh binding to nicotinic and muscarinic receptors in rat intracardiac neurons.

Alterações na estrutura anatômica da madeira de cavacos de eucalyptus grandis em três condições de desfibramento para a confecção de painéis MDF

A utilização da madeira de eucalipto na confecção de painéis MDF é recente, tornando-se necessário entender as modificações em sua estrutura anatômica durante as etapas do processo industrial, notadamente no desfibramento dos cavacos. Com esse objetivo, neste estudo foram aplicadas três condições diferenciadas de desfibramento dos cavacos, alterando-se (i) o tempo de aquecimento, (ii) as pressões de digestão e de desfibramento e (iii) a energia específica de desfibramento, sendo avaliadas as características anatômicas dos componentes celulares da madeira. O aumento da intensidade de refino dos cavacos de madeira reduziu o comprimento médio das fibras e aumentou o porcentual de fibras quebradas, corroborando as imagens de microscopia eletrônica de varredura, além da diminuição do número dos vasos e de células de parênquima. Essa condição de desfibramento mais intensa promoveu, também, um característico escurecimento da coloração da polpa composta pelos elementos celulares da madeira. A aplicação de variáveis de desfibramento mais brandas aumentou a presença de feixes de fibras e do número de vasos e de parênquima, resultando em uma polpa de coloração mais clara. As alterações das características morfológicas dos componentes celulares da madeira dos cavacos de eucalipto, após o tratamento de desfibramento, relacionaram-se com as etapas do processo operacional e com a qualidade tecnológica dos painéis de fibras MDF.

Conceitos de eletricidade e suas aplicações tecnológicas : uma unidade de ensino potencialmente significativa

O presente trabalho teve como objetivo central a elaboração de uma unidade de ensino sobre conceitos de eletricidade e validação desse material como uma Unidade de Ensino Potencialmente Significativa (UEPS). Assim, foi desenvolvida uma unidade de ensino sobre os temas diferença de potencial, corrente elétrica e suas aplicações sob a luz da Teoria da Aprendizagem Significativa de Ausubel e aplicada em seis turmas do terceiro ano do ensino médio de uma escola estadual do Espírito Santo. A fim de investigação das potencialidades desse método de ensino, utilizou-se metodologias de pesquisa qualitativa descritiva interpretativa e quantitativa préexperimental. Tendo em vista a importância dos conhecimentos prévios dos estudantes para promover aprendizagem significativa, no início do estudo foram aplicados questionários de opinião, realizados diálogos prévios e construções de mapas conceituais, sendo esses importantes instrumentos para a adequação do material apresentado ao aluno em relação ao seu perfil e à sua estrutura cognitiva. Para coleta de dados da pesquisa foram feitas gravações em áudio das principais etapas, diários de bordo, fotografias dos trabalhos, questionários e mapas conceituais prévios e finais e, finalmente, avaliação escrita. A análise dos mapas conceituais constituiu um dos principais instrumentos para avaliação sob o ponto de vista do desenvolvimento cognitivo dos estudantes, no sentido de classificar os mapas, associá-los às estruturas cognitivas de quem os construiu e identificar variações estatisticamente válidas em relação às construções de novos significados. A investigação revelou que, de modo geral, a unidade foi responsável por melhorias significativas na predisposição dos alunos em aprender e na promoção da aprendizagem significativa, possibilitando sua a validação como uma UEPS.

The quest for a sustainable product: An environmental study of tyre recyclates

The main objective of the present study is to assess the environmental advantages of substituting aluminium for a polymer composite in the manufacture of a structural product (a frame to be used as a support for solar panels). The composite was made of polypropylene and a recycled tyres’ rubber granulate. Analysis of different composite formulations was performed, to assess the variation of the environmental impact with the percentage of rubber granulate incorporation. The results demonstrate that the decision on which of the two systems (aluminium or composite) has the best life cycle performance is strongly dependent on the End-of Life (EoL) stage of the composite frame. When the EoL is deposition in a landfill, the aluminium frame performs globally better than its composite counterpart. However, when it is incineration with energy recovery or recycling, the composite frame is environmentally preferable. The raw material production stage was found to be responsible for most of the impacts in the two frame systems. In that context, it was shown that various benefits can accrue in several environmental impact categories by recycling rubber tyres and using the resulting materials. This is in a significant part also due to the recycling of the steel in the tyres. The present work illustrates how it is possible to minimize the overall environmental impact of consumer products through the adequate selection of their constitutive materials in the design stage. Additionally it demonstrates how an adequate EoL planning can be an important issue when developing a sustainable product, since it can highly influence its overall life cycle performance.

Validation of percutaneous puncture trajectory during renal access using 4D ultrasound reconstruction

Background: An accurate percutaneous puncture is essential for disintegration and removal of renal stones. Although this procedure has proven to be safe, some organs surrounding the renal target might be accidentally perforated. This work describes a new intraoperative framework where tracked surgical tools are superimposed within 4D ultrasound imaging for security assessment of the percutaneous puncture trajectory (PPT). Methods: A PPT is first generated from the skin puncture site towards an anatomical target, using the information retrieved by electromagnetic motion tracking sensors coupled to surgical tools. Then, 2D ultrasound images acquired with a tracked probe are used to reconstruct a 4D ultrasound around the PPT under GPU processing. Volume hole-filling was performed in different processing time intervals by a tri-linear interpolation method. At spaced time intervals, the volume of the anatomical structures was segmented to ascertain if any vital structure is in between PPT and might compromise the surgical success. To enhance the volume visualization of the reconstructed structures, different render transfer functions were used. Results: Real-time US volume reconstruction and rendering with more than 25 frames/s was only possible when rendering only three orthogonal slice views. When using the whole reconstructed volume one achieved 8-15 frames/s. 3 frames/s were reached when one introduce the segmentation and detection if some structure intersected the PPT. Conclusions: The proposed framework creates a virtual and intuitive platform that can be used to identify and validate a PPT to safely and accurately perform the puncture in percutaneous nephrolithotomy.

Diagnóstico molecular de cancros hereditários por sequenciação de nova geração: cancro da mama e cancro colorretal

O cancro da mama e o cancro colorretal constituem duas das principais causas de morte a nível mundial. Entre 5 a 10% destes casos estão associados a variantes germinais/hereditárias em genes de suscetibilidade para cancro. O objetivo deste trabalho consistiu em validar a utilização da sequenciação de nova geração (NGS) para identificar variantes previamente detetadas pelo método de Sanger em diversos genes de suscetibilidade para cancro da mama e colorretal. Foram sequenciadas por NGS 64 amostras de DNA de utentes com suspeita clínica de predisposição hereditária para cancro da mama ou colorretal, utilizando o painel de sequenciação TruSight Cancer e a plataforma MiSeq (Illumina). Estas amostras tinham sido previamente sequenciadas pelo método de Sanger para os genes BRCA1, BRCA2, TP53, APC, MUTYH, MLH1, MSH2 e STK11. A análise bioinformática dos resultados foi realizada com os softwares MiSeq Reporter, VariantStudio, Isaac Enrichment (Illumina) e Integrative Genomics Viewer (Broad Institute). A NGS demonstrou elevada sensibilidade e especificidade analíticas para a deteção de variantes de sequência em 8 genes de suscetibilidade para cancro colorretal e da mama, uma vez que permitiu identificar a totalidade das 412 variantes (93 únicas, incluindo 27 variantes patogénicas) previamente detetadas pelo método de Sanger. A utilização de painéis de sequenciação de genes de predisposição para cancro por NGS vem possibilitar um diagnóstico molecular mais abrangente, rápido e custo-eficiente, relativamente às metodologias convencionais.

Placas de OSB: investigação e estudo laboratorial das suas características de desempenho

A utilização de placas de OSB – Oriented Strand Board está em franca expansão no território nacional e parece ser uma alternativa ecológica e económica aos painéis de derivados de madeira normalmente usados. O OSB é obtido num processo de fabrico resultante da interacção de diversas variáveis, que conferem aos painéis uma vasta gama de aplicações estruturais ou não estruturais (paredes exteriores e interiores, pavimentos, coberturas, componentes de vigas, cofragens, embalagens, móveis, elementos de decoração, etc.). Neste trabalho pretendeu-se investigar, através de pesquisa bibliográfica as características das placas OSB assim como seu processo de fabrico e condicionantes existentes no seu decurso. Em seguida estas foram comparadas com os seus principais concorrentes, o contraplacado e o aglomerado de madeira e cimento. O trabalho experimental realizado teve como objectivo analisar as propriedades de OSB, proveniente do mercado nacional, de acordo com a EN 300:2006 e com os dados recolhidos na pesquisa bibliográfica. Foram executados ensaios de flexão (EN 310:2002), inchamento em espessura (EN 317:2002) e ensaios de flexão após envelhecimento (EN 321:2010). Concluiu-se que o OSB é um material com algumas características de destaque, no entanto a substituição de outros derivados de madeira por este deve ser acompanhada por estudos, principalmente em ambientes húmidos. É importante realçar que este possui modelos com características específicas para determinadas utilizações e ambientes que possibilitam uma optimização do seu comportamento, no entanto, nos ensaios realizados apenas foi utilizado um modelo base de OSB.

Folk culture and political power: practices and representations of moliceiro culture in Portugal, cultural sociology

This article analyses the painted panels of the moliceiro boat, a traditional working boat of the Ria de Aveiro region of Portugal. The article examines how the painted panels have been invented and reinvented over time. The boat and its panels are contextualized both within the changing socio-economic conditions of the Ria de Aveiro region, and the changing socio-political conditions of Portugal throughout the 20th century and until the present day. The article historically analyses the social significance of ‘moliceiro culture’, examining in particular the power relations it expresses and its ambiguous past and present relationships with the political and the economic powers of the Portuguese state. The article unpacks some of the complexity of the relations that have pertained between public and private, local and national, folk culture and ‘art’, and popular and institutional in the Ria de Aveiro region in particular, and Portugal more generally.