Avaliação da aplicação de modelos para a secagem de pastas e suspensões em leito de jorro com alimentação contínua

This work studies the development, implementation and improvement of a macroscopic model to describe the behavior of the spouted bed dryer with continuous feeding for pastes and suspensions drying. This model is based on the CST model (Freire et al., 2009) and the model of Fernandes (2005), whose theoretical foundation is based on macroscopic mass and heat balances for the three phases involved in the process: gas, liquid and solid. Because this technique is quite relevant, the studies of modeling and simulation of spouted bed drying are essential in the analysis of the process as a whole, because through them it is possible to predict and understand the behavior of the process, which contributes significantly to more efficient project and operation. The development and understanding of the phenomena involved in the drying process can be obtained by comparing the experimental data with those from computer simulations. Such knowledge is critical for choosing properly the process conditions in order to obtain a good drying efficiency. Over the past few years, researches and development of works in the field of pastes and suspensions drying in spouted bed has been gaining ground in Brazil. The Particulate Systems Laboratory at Universidade Federal do Rio Grande do Norte, has been developing several researches and generating a huge collection of experimental data concerning the drying of fruit pulps, vegetables pastes, goat milk and suspensions of agro-industrial residues. From this collection, some data of goat milk and residue from acerola (Malpighia glabra L.) drying were collected. For the first time, these data were used for the development and validation of a model that can describe the behavior of spouted bed dryer. Thus, it was possible to model the dryer and to evaluate the influence of process variables (paste feeding, temperature and flow rate of the drying air) in the drying dynamics. We also performed water evaporation experiments in order to understand and to study the behavior of the dryer wall temperature and the evaporation rate. All these analysis will contribute to future works involving the implementation of control strategies in the pastes and suspensions drying. The results obtained in transient analysis were compared with experimental data indicating that this model well represents the process

Novas alternativas de remoção de enxofre do óleo diesel utilizando tensoativos e microemulsões

The diesel combustion form sulfur oxides that can be discharged into the atmosphere as particulates and primary pollutants, SO2and SO3, causing great damage to the environment and to human health. These products can be transformed into acids in the combustion chamber, causing damage to the engines. The worldwide concern with a clean and healthy environment has led to more restrictive laws and regulations regulating the emission levels of pollutants in the air, establishing sulfur levels increasingly low on fuels. The conventional methods for sulfur removal from diesel are expensive and do not produce a zero-level sulfur fuel. This work aims to develop new methods of removing sulfur from commercial diesel using surfactants and microemulsion systems. Its main purpose is to create new technologies and add economic viability to the process. First, a preliminary study using as extracting agent a Winsor I microemulsion system with dodecyl ammonium chloride (DDACl) and nonyl phenol ethoxylated (RNX95) as surfactant was performed to choose the surfactant. The RNX95 was chosen to be used as surfactant in microemulsioned systems for adsorbent surface modification and as an extracting agent in liquid-liquid extraction. Vermiculite was evaluated as adsorbent. The microemulsion systems applied for vermiculite surface modification were composed by RNX95 (surfactant), n-butanol (cosurfactant), n-hexane (oil phase), and different aqueous phases, including: distilled water (aqueous phase),20ppm CaCl2solution, and 1500ppm CaCl2solution. Batch and column adsorption tests were carried out to estimate the ability of vermiculite to adsorb sulfur from diesel. It was used in the experiments a commercial diesel fuel with 1,233ppm initial sulfur concentration. The batch experiments were performed according to a factorial design (23). Two experimental sets were accomplished: the first one applying 1:2 vermiculite to diesel ratio and the second one using 1:5 vermiculite to diesel ratio. It was evaluated the effects of temperature (25°C and 60°C), concentration of CaCl2in the aqueous phase (20ppm and 1500ppm), and vermiculite granule size (65 and 100 mesh). The experimental response was the ability of vermiculite to adsorb sulfur. The best results for both 1:5 and 1:2 ratios were obtained using 60°C, 1500ppm CaCl2solution, and 65 mesh. The best adsorption capacities for 1:5 ratio and for 1:2 ratio were 4.24 mg sulfur/g adsorbent and 2.87 mg sulfur/g adsorbent, respectively. It was verified that the most significant factor was the concentration of the CaCl2 solution. Liquid-liquid extraction experiments were performed in two and six steps using the same surfactant to diesel ratio. It was obtained 46.8% sulfur removal in two-step experiment and 73.15% in six-step one. An alternative study, for comparison purposes, was made using bentonite and diatomite asadsorbents. The batch experiments were done using microemulsion systems with the same aqueous phases evaluated in vermiculite study and also 20ppm and 1500 ppm BaCl2 solutions. For bentonite, the best adsorption capacity was 7.53mg sulfur/g adsorbent with distilled water as aqueous phase of the microemulsion system and for diatomite the best result was 17.04 mg sulfur/g adsorbent using a 20ppm CaCl2solution. The accomplishment of this study allowed us to conclude that, among the alternatives tested, the adsorption process using adsorbents modified by microemulsion systems was considered the best process for sulfur removal from diesel fuel. The optimization and scale upof the process constitutes a viable alternative to achieve the needs of the market

Uso do sensoriamento remoto orbital no monitoramento da dispersão de macrófitas nos reservatórios do complexo Tietê

A presença de algumas substâncias na água, como pigmentos fotossintetizantes, particulados, etc., afeta sua cor, provocando mudanças na radiância da água registrada por sensores orbitais. Nesse sentido, o sensoriamento remoto pode se constituir em uma fonte complementar de dados para o monitoramento da qualidade da água em grandes reservatórios (Novo et al., 1994). No contexto de um projeto de pesquisa realizado na AES Tietê S.A., com o objetivo de desenvolver técnicas para a avaliação da área com infestação de plantas aquáticas, imagens orbitais multiespectrais foram usadas tanto para mapear a dispersão espacial e estimar a área de ocorrência de macrófitas aquáticas, em duas épocas distintas, quanto para orientar a definição de pontos de amostragem in loco, visando a coleta e posterior análise da água e de sedimentos nos reservatórios. Este trabalho apresenta uma descrição do procedimento metodológico adotado na análise das imagens multiespectrais, bem como os resultados obtidos na caracterização dos reservatórios de Barra Bonita, Bariri, Ibitinga, Promissão e Nova Avanhandava, em termos de seu dimensionamento, variabilidade espectral da água e presença de macrófitas emersas, nas duas épocas do ano consideradas.

Qualidade de vida de pacientes com deformidade dentofacial

In the last decade, an increasing number of studies focusing on the impact of oral deformities on quality of life have been published. However, the evaluation of patients at different phases of the treatment has not been performed. Therefore, the purpose of this study was to determine the impact that dentofacial deformities have on patients` quality of life, as well as the influence exerted by social, economic, demographic and orthodontic factors, type and severity of malocclusion. A bicentric study - of the cross-sectional type of repeated panels - involving two cities - Natal and Rio de Janeiro - was carried out. A total of 227 patients participated in the study: 71 patients in the initial phase of the treatment (before any orthosurgical procedure), 115 patients in the pre-surgical (with braces) phase and 41 patients in the postoperative phase. The quality of life was measured using the Orthognatic Quality of Life Questionnnaire - OQLQ, translated and validated into Portuguese. The normative and aesthetic need for treatment was assessed with the Index of Orthodontic Treatment Need (IOTN) and the Dental Aesthetic Index (DAI); the social, economic and demographic factors, the type of service and malocclusion were also assessed. The data were analyzed through χ2/ Fisher`s exact test to seek the association between the nominal categorical variables in the three phases of treatment, Mann Whitney and Kruskal-Wallis test for gauging the existence of significant differences between two and three groups regarding each domain of OQLQ, respectively. For all tests, it was adopted a significance level of 5%. There was a statistically significant difference (p <0.001) in the general scores of OQLQ and in the domains of social aspects, facial aesthetics and oral function, when the "postoperative group" was compared to the "initial" and "orthodontic preparation" groups. Women, single, aged between 31 and 59 and living in Natal had the greatest impact on quality of life among patients in the "orthodontic preparation" group. Only the variable "income" (2 to 3 minimum wages), for the "initial" group, and gender (female) for the "postoperative" group, showed significant association with quality of life. The normative variable IOTN (DHC and AC) showed significant association with the OQLQ for the "initial" group, and the IOTN-AC-auto in the group of orthodontic preparation, being less important to women. We conclude that the ortho-surgical therapy has positive effects on quality of life after orthognathic surgery

Publicações indexadas geradas a partir de resumos de congressos de angiologia e cirurgia vascular no Brasil

CONTEXTO: Grande parte da produção científica apresentada em congressos não é publicada. Mesmo nos países do primeiro mundo, os números demonstram que essa perda é expressiva. OBJETIVO: Dimensionar o número de artigos publicados e indexados em bases de dados nacionais e internacionais, a partir dos títulos e autores de temas livres ou painéis dos congressos brasileiros de cirurgia vascular de 2001 e 2003. MÉTODOS: Foram pesquisados os 541 e 567 resumos apresentados, respectivamente, no XXXIV Congresso Brasileiro de Angiologia e Cirurgia Vascular, em 2001 e no XXXV Congresso de Angiologia e Cirurgia Vascular, em 2003. Foi realizada pesquisa computadorizada através dos seguintes instrumentos de busca: Scirus, Bireme, LILACS, SciELO, MEDLINE-PubMed e Biblioteca Cochrane, Google Acadêmico e índices remissivos e onomásticos do Jornal Vascular Brasileiro. Os artigos foram classificados em internacionais ou nacionais e em completos ou modificados. RESULTADOS: Foram encontrados 21 (3,89%) e 49 (8,64%) artigos publicados, a partir dos congressos de 2001 e 2003, respectivamente. A média de publicação dos dois congressos foi de 6,32%. CONCLUSÕES: Os números revelados nessa amostra revelam o quanto a publicação das pesquisas no Brasil é relegada a segundo plano. Muitos trabalhos deixam de ser publicados pela falta de prioridade e tradição em escrever, falta de tempo, empenho e de incentivo.

O problema de corte de estoque em indústrias de móveis de pequeno e médio portes

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Mudar o ensino?: concepções, perspectivas e valores de professores de 5ª a 8ª séries

O artigo relata uma experiência, parte de Projeto mais amplo, visando conduzir professores de 1° grau a refletirem sobre os fundamentos de sua prática e sensibilizá-los à mudança. O trabalho desenvolveu-se em encontros semanais mediante debates, painéis, dramatização, coleta de dados junto a alunos e aplicação da técnica das palavras-chave. Os resultados mostram avanços na tomada de consciência do professor quanto ao próprio papel e aos pressupostos de sua ação, além do predomínio de visão equilibrada sobre o modelo tradicional de ensino e perspectiva positiva quanto a sua mudança. As conclusões apontam para a necessidade constante de o professor rever os fundamentos de sua atuação e de buscar ultrapassar o nível do simples fazer da prática, em direção a sua compreensão.

Influência das propriedades de granulados de celulose nas características físicas dos comprimidos

The compaction behavior of powdered solids can be strongly influenced by the physicochemical properties of excipients because they are frequently present in the tablet in larger amounts than the drug itself. The aim of this study was to assess the influence of the granule size of the cellulose on the physical characteristics of tablets produced in punches of different diameters, since this relation has never been explored in the literature. Granules of several sizes were produced by wet granulation and compressed in punches of various diameters by applying different forces. Size distribution, apparent density and flow of granules were assessed, as well as physical characteristics of the tablets (weight, hardness, friability and disintegration time). Reducing the granule size resulted in tablets of adequate crushing strength and fast disintegration; moreover, it allowed tablets to be produced without the need to use forces near the upper limit of the press, thus avoiding premature wear on the tabletting machine. Thus, once a suitable size for a given tablet formulation has been chosen, the granule size selected has been shown to determine the crushing strength of the tablet.

Geração de padrões de corte n-grupos para a indústria moveleira

Neste artigo são apresentadas propostas de soluções para o problema de geração de padrões de corte n-grupos para o corte da matéria-prima na indústria moveleira. Este problema NP-difícil aparece em diversos outros processos industriais que incluem o corte de painéis retangulares grandes de tamanho padrão em retângulos menores. O planejamento dos cortes é um aspecto importante do planejamento da produção nestas indústrias, pois efeitos negativos tais como o perda de matériaprima e tempo de preparo da máquina de corte podem ser minimizados, diminuindo assim os custos de produção. É estudada a eficiência de modelos lineares inteiros para resolver o problema do corte guilhotinado bidimensional propostos em [33,34], bem como o seu uso na geração de colunas para o problema de corte de estoque. São usados dados reais de uma fábrica de móveis de pequeno porte característica do pólo moveleiro de Votuporanga/SP. Os resultados obtidos indicam que as estratégias propostas geram perdas dentro dos requisitos exigidos pela fábrica. © SPM.

Os trabalhadores do Café: análise de uma obra de Portinari

Pós-graduação em Artes - IA

Arte em cerâmica e a memória como elemento criativo

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Mini-inversores para aproveitamento de energia fotovoltaica, com técnicas de MPPT, sincronismo e conexão com a rede de CA em BT, proteção de ilhamento, gerenciamento da energia e da operação

Pós-graduação em Engenharia Elétrica - FEIS

Análise das propriedades reológicas de materiais cimentícios associando o conceito de empacotamento de partículas

Pós-graduação em Engenharia Mecânica - FEIS

Investigação reológica e análise mecânica de compósitos não-newtonianos

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Métodos de determinação da densidade básica e aparente da madeira de Eucalyptus sp

Pós-graduação em Agronomia (Energia na Agricultura) - FCA