Análise pedoestratigráfica das formações Rio Claro e Piraçununga, no Centro-Leste do Estado de São Paulo

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Ceramic raw materials from the State of Maranhão, Brazil. Part 1: chemical and mineralogical characterization and technological properties of clays from São Luis, Rosário, Pinheiro and Mirinzal

Nesse trabalho, foram caracterizadas algumas argilas coletadas nos municípios de São Luís, Rosário, Pinheiro e Mirinzal. A caracterização foi realizada através dos ensaios de difração de raios X, massa específica real, capacidade de troca de cátions (CTC), área superficial, distribuição granulométrica, análise química, análise térmica (TG-DTA) e limites de Atterberg. Ensaios tecnológicos de retração linear, antes e após a queima, absorção de água e tensão de ruptura a flexão, em três pontos, foram realizados em corpos de prova prensados uniaxialmente a 20 MPa e tratados termicamente em 850, 950, 1050, 1150 e 1250ºC. Os resultados obtidos permitiram identificar duas argilas de queima branca, constituídas de quartzo, caolim, feldspato e anatásio, com excelentes propriedades para uso em cerâmica branca. As restantes são queima vermelha e possuem composição mineralógica de quartzo, caolim, feldspato, montmorilonita, hematita e goetita. Estas últimas apresentaram valores moderados de plasticidade e são adequadas para aplicações em cerâmica vermelha.

Ocorrência de uma nova bentonita brasileira nos basaltos intemperizados da formação Mosquito, bacia do Parnaíba, sul do Maranhão

No município de Formosa da Serra Negra, sul do Maranhão, às margens da rodovia MA006, encontram-se afloramentos de basaltos intemperizados da Formação Mosquito, apresentando textura bastante argilosa e potencial de ser um material bentonítico. Neste trabalho, esse material que vem sendo considerado uma nova ocorrência de bentonita no Brasil e, batizado de Formosa, foi caracterizado por difração de raios X, fluorescência de raios X, microscopia eletrônica de varredura, espectroscopia Mössbauer e capacidade de troca catiônica, em amostra total e após separação granulométrica, e ainda, comparada com duas das principais bentonitas brasileiras, Chocolate e Bofe. Apesar das variações químicas e mineralógicas encontradas, muito comuns nesse tipo de argila, as semelhanças observadas convencem o promissor uso da argila Formosa como bentonita, uma vez que o ponto principal da caracterização está na presença dominante de montmorillonita e baixa concentração de outras fases minerais, mostrando que esse material apresenta mineralogia importante do ponto de vista tecnológico.

Organofilização de uma Mg-bentonita da bacia do Parnaíba-Sul do Maranhão e sua utilização em poli (metacrilato de metila)

Bentonitas são argilas que tem como seu principal constituinte argilominerais do grupo da esmectita, predominantemente montmorillonita. De acordo com o cátion predominante no espaço intercamada da esmectita, a bentonita pode ser classificada como sódica, cálcica ou magnesiana. Essas argilas possuem vasta aplicação industrial, como fluidos de perfuração, pelotização, moldes de fundição, dentre outros. Para algumas aplicações mais específicas e que agregam maior valor ao produto final, como na síntese de nanocompósitos polímero/argila, faz-se necessário à intercalação de íons orgânicos na intercamada do argilomineral. No Brasil, a produção industrial de argilas organofílicas é pequena e voltada para os mercados de tintas, graxas e resinas de poliéster. Empresas do setor de bentonitas, que ainda não estão produzindo esse tipo de material, vêm mostrando crescente interesse nesta aplicação. Dentro desse contexto, este trabalho buscou avaliar o potencial da Bentonita Formosa, uma Mg-bentonita recentemente descrita e relativamente abundante no nordeste do Brasil, na produção de argilas organofílicas e sua aplicação em síntese de nanocompósitos polímero/argila. Para isso, foram realizadas sínteses variando a concentração dos íons surfactantes hexadeciltrimetilamônio (HDTMA⁺) e dodeciltrimetilamônio (DTMA⁺) em 0,7, 1,0 e 1,5 vezes o valor de CEC, com tempo de reação de 12 horas e variação de temperatura de 25 ºC e 80 ºC. A Mg-Bentonita in natura e ativada com carbonato de sódio foi utilizada como material de partida. Tanto o material de partida como as argilas organofílicas obtidas foram caracterizadas por DRX, DTA/TG e IV. As argilas que apresentaram melhores resultados de intercalação foram utilizadas nas proporções de 1%, 3% e 10% para a síntese de nanocompósitos poli(metacrilato de metila) (PMMA)/argila. As análises de DRX confirmaram a intercalação dos íons orgânicos no espaço intercamada da Mg-esmectita com e sem ativação. Com os resultados de IV foi possível observar que a razão de confôrmeros gauche/trans diminui com o aumento do espaçamento basal. Os resultados de DTA/TG confirmaram a estabilidade térmica das argilas organofílicas à temperatura máxima de 200 °C, o que possibilita a utilização desse material em síntese de nanocompósitos polímero/argila obtidos por processo de fusão. A análise de DRX confirmou a intercalação do PMMA no espaço intercamada da Mg-esmectita em todos os nanocompósitos produzidos. Com as análises de DSC foi possível observar o aumento da temperatura de transição vítrea para todos os nanocompósitos, quando comparados com PMMA puro. Com isso, é possível concluir que a Mg-Bentonita pode ser intercalada com íons alquilamônio, sem a necessidade prévia de ativação sódica, formando argilas organofílicas, assim como sua utilização em síntese de nanocompósitos. Essa possibilidade de utilização da Mg-bentonita in natura pode representar uma importante diferença em termos de custos de processo, na comparação com as bentonitas cálcicas existentes no Brasil, ou mesmo as importadas, que precisam ser ativadas durante o beneficiamento. Finalmente, acredita-se que a pesquisa deve avançar com a avaliação das propriedades mecânicas dos nanocompósitos produzidos neste trabalho, visando as diferentes possibilidades de aplicações desses materiais.

CARACTERÍSTICAS DAS ROCHAS DA FORMAÇÃO CORUMBATAÍ UTILIZADAS NA INDÚSTRIA DE REVESTIMENTO CERÂMICO.

A Formação Corumbataí é atualmente utilizada com sucesso pela indústria de revestimento cerâmico no pólo de cerâmica de Santa Gertrudes. Este engloba os municípios de Santa Gertrudes, Rio Claro, Cordeirópolis, Limeira, Piracicaba e Araras. De acordo com os estudos geológicos realizados, as argilas da Formação Corumbataí foram divididas em cinco litofácies cerâmicas, sendo elas: maciça, laminada, intercalada I, intercalada II e alterada. De acordo com suas características químicas, são consideradas como argilas com teores médios de elementos fundentes, com os valores da soma dos óxidos alcalinos (Na2O + K2O) variando de 2,9% na litofácies alterada até valores de 4,3% na litofácies intercalada I. Os argilominerais predominantes são a illita e a caulinita (presentes em todas as litofácies), além da montmorillonita que ocorre com freqüência nas litofácies intercalada I e II e laminada. Outros minerais importantes são: quartzo, feldspato do tipo albita, hematita e calcita. Os resultados cerâmicos possibilitaram enquadrar as litofácies cerâmicas dentro do Grupo BIIb na Classificação de Revestimentos Cerâmicos (BII – valores de resistência à flexão da ordem de 180-300 Kgf/cm2; b – valores de absorção de água (Abs) de 6 a 10%), porém, alguns valores de Abs ficaram acima de 10% nas litofácies intercalada I, intercalada II e na alterada.

Estudo eletroquímico do sistema microestruturado montmorilonita-8- hidroxiquinolina na presença de íons metálicos

Pós-graduação em Química - IBILCE

Materiais híbridos argila-poli(metil metacrilato) obtidos através do método grafting

Pós-graduação em Química - IQ

Preparation of a clay-modified carbon paste electrode based on 2-thiazoline-2-thiol-hexadecylammonium sorption for the sensitive determination of mercury

A montmorillonite from Wyoming-USA was used to prepare an organo-clay complex, named 2-thiazoline-2-thiol-hexadecyltrimethylammonium-clay (TZT-HDTA-clay), for the purpose of the selective adsorption of the heavy metals ions and possible use as a chemically modified carbon paste electrode (CMCPE). Adsorption isotherms of Hg 2+, Pb 2+, Cd 2+, Cu 2+, and Zn 2+ from aqueous solutions as a function of the pH were studied at 298 K. Conditions for quantitative retention and elution were established for each metal by batch and column methods. The organo-clay complex was very selective to Hg(II) in aqueous solution in which other metals and ions were also present. The accumulation voltammetry of Hg(II) was studied at a carbon paste electrode chemically modified with this material. The mercury response was evaluated with respect to the pH, electrode composition, preconcentration time, mercury concentration, cleaning solution, possible interferences and other variables. A carbon paste electrode modified by TZT-HDTA-clay showed two peaks: one cathodic peak at about 0.0 V and an anodic peak at 0.25 V, scanning the potential from -0.2 to 0.8 V (0.05 M KNO 3 vs. Ag/AgCl). The anodic peak at 0.25 V presents excellent selectivity for Hg(II) ions in the presence of foreign ions. The detection limit was estimated as 0.1 μg L -1. The precision of determination was satisfactory for the respective concentration level. 2005 © The Japan Society for Analytical Chemistry.

Spectral Induced Polarization (SIP) signatures of clayey soils containing toluene

We performed laboratory experiments to investigate the sensitivity of the Spectral Induced Polarization (SIP) method to toluene contamination in clayey soils. We used mixtures of quartzitic sand and montmorillonite as soil samples, artificially contaminated with varying amounts of toluene. Care was taken to quantify the experimental uncertainty resulting from packing since such effects must be quantified if variations in SIP signatures between samples are to be reliably interpreted in terms of the effects of hydrocarbon concentration. The SIP response of all samples following addition of toluene was monitored for a period of 40 days following sample preparation. Stepwise regression was used to examine the statistical significance of correlations between (i) clay content and (ii) toluene concentration and SIP parameters. Both single-frequency real and imaginary conductivity measurements, along with the integral chargeability, normalized chargeability, DC conductivity and time constant obtained from a Debye decomposition fitting, were examined in this regression analysis. The SIP measurements show a clear time dependence following sample preparation, indicating that samples containing toluene may take significant time to reach an equilibrium electrical response. SIP measurements are significantly related to toluene content shortly after sample preparation, when the expected dependence of SIP on clay concentration is apparently suppressed. However, for the state of electrical equilibrium after 40 days (interpreted to indicate surface chemistry at equilibrium) there is no significant relation between SIP measurements and toluene content; instead SIP measurements are then significantly correlated with clay concentration. The total chargeability, normalized chargeability and relaxation time obtained from the Debye decomposition show no correlation with toluene content, indicating that this procedure, which likely integrates over multiple mechanisms, may not be suitable for understanding relationships between SIP and hydrocarbon contamination. We find only small low-frequency polarization signals observed in relation to toluene concentration (2 mrad at 0.01 Hz), which initially decreases the interfacial polarization. Unlike earlier works, our results do not support the use of the SIP method as a tool for monitoring toluene contamination in clay soils.

Influence of the relative amounts of crystalline and amorphous phases on the mechanical properties of polyamide-6 nanocomposites

The relative amounts of amorphous and crystalline ?- and a-phases in polyamide-6 nanocomposites, estimated from the deconvolution of X-ray diffraction peaks using Gaussian functions, correlates with their mechanical, thermomechanical, and barrier properties. The incorporation of organoclay platelets (Cloisite 15A and 30B) induced the crystallization of the polymer in the ? form at expense of the amorphous phase, such that 12 wt % of Cloisite is enough to enhance the mechanical and the thermomechanical properties. However, higher nanofiller loads were necessary to achieve good barrier effects, because this property is mainly dependent on the tortuous path permeation mechanism of the gas molecules through the nanocomposite films. (C) 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012

Hybrid Materials Based on Smectite Clays and Nutraceutical Anthocyanins from the Acai Fruit

Hybrid materials were prepared by combining clay mineral (montmorillonite SWy-2 and saponite SapCa-1) and dyes extracted from the acai (Euterpe oleracea Mart.) fruit, which contains mainly anthocyanins from the 3-glucoside class, to increase the stability of the dye and facilitate its handling and storage. Clay minerals are common ingredients in therapeutic and pharmaceutical products and acai phytochemicals show disease prevention properties. The extract of the acai fruit was mixed with water suspensions of layered silicates in different proportions. The dyeclay hybrids presented incorporated organic material in amounts up to 24 wt.-%. X ray diffractometry and vibrational (FTIR and Raman) and electronic spectroscopic data showed that flavylium cations were successfully intercalated between the inorganic layers. Mass-coupled thermogravimetric analysis (TGA-MS) data showed a significant gain in the thermostability of the organic species in relation to anthocyanins in the extract. MS curves related to CO2 release (m/z = 44) are ascendant above 200 degrees C when the dye cations are confined to the inorganic structure. The radical scavenging activity of the hybrid materials was monitored by electron paramagnetic resonance (EPR) toward the stable radical DPPH (1,1-diphenyl-2-picrylhydrazyl) and compared to the activity of the acai extract. In addition to the fact that interaction with clay minerals improves the stability of the acai dyes against heat, their properties as radical scavengers are preserved after intercalation. The improvement in the properties of the nutraceutical species by intercalation by using biocompatible inorganic structures can be valuable for human therapy.

CHARACTERIZATION OF REGOSOLS IN THE SEMIARID REGION OF PERNAMBUCO, BRAZIL

CHARACTERIZATION OF REGOSOLS IN THE SEMIARID REGION OF PERNAMBUCO, BRAZIL Studies on soil characterization in unexplored regions, besides the generation of data banks for the soil classes of the country, also produce scientific information about soil properties, important for the development of good management practices and sustainable land use. One of the main soil classes in the semiarid region of Pernambuco State, the Regosols, cover about 27 % of the state area, and are used mainly for family agriculture. Due to different geological and climatic aspects Regosols with different chemical, physical and mineralogical properties are found in Pernambuco, which were characterized for the semiarid region of the State. Five Regosol profiles were selected in different regions of the State (P1=Sao Caetano; P2=Lagoa do Ouro; P3=Caetes; P4=Sao Joao; P5=Parnamirim). The soils were morphologically characterized and samples collected from all horizons and the bedrock. Routine physical and chemical analyses were carried out for soil classification of all samples and mineralogical analyses of the coarse fractions (gravel and sand) by optical microscopy and of the silt and clay fractions by X ray diffraction (XRD), as well as petrographic analyses of the rock samples. The results showed similarities between the soils, with a low degree of pedogenetic development, varying from medium to very deep, with the horizon sequence A-AC-C-Cr and a sandy to sandy loam texture. In the deeper layers of two profiles (P1 and P5), a solodic character was observed. Organic matter and available phosphorus content were low in all studied soils. Despite the low levels of exchangeable cations, all soil profiles showed high base saturation. The mineralogical composition of gravel, sand and silt fractions consisted, essentially, of quartz, followed by feldspars and mica, supporting the results of the petrographic analysis of the bedrock. Kaolinite was the main clay mineral in all studied profiles and horizons, indicating an important monosialitization process in autochthonous soils of a typical semiarid region. In soil profile P2, at a lower landscape position, smectite minerals were observed, with mixing phases of montmorillonite, beidelite or nontronite, indentified by the Greene-Kelly test in the DRX analysis.

Fotodegradação de compósitos de poliestireno/argila montmorilonita: efeito do tipo de argila e presença de sal

Compósitos de poliestireno/montmorilonita (PS/MMT) contendo 2,5% em peso de argila foram preparados com dois tipos de argila modificada com sais quaternários de amônio. Também foram preparadas amostras do PS + sal quaternário de amônio, utilizando-se proporção de sal semelhante à usada na modificação da argila. Todas as amostras foram expostas à radiação UV por períodos de até 12 semanas, e em seguida foram realizados testes para avaliar as modificações em massa molar, propriedades mecânicas (tração e impacto), estrutura química (FTIR) e superfície de fratura (MEV) dessas amostras. Os resultados mostraram que compostos metálicos existentes na argila catalisam o processo fotodegradativo do PS e a presença isolada do sal não altera significativamente o comportamento do PS frente à radiação UV.

Structure and properties of composite polyolefin materials

This thesis is based on three main studies, all dealing with structure-property investigation of semicrystalline polyolefin-based composites. Low density poly(ethylene) (LDPE) and isotactic poly(propylene) (iPP) were chosen as parts of the composites materials and they were investigated either separately (as homoploymers), either in blend systems with the composition LDPE/iPP 80/20 or as filled matrix with layered silicate (montmorillonite). The beneficial influence of adding ethylene-co-propylene polymer of amorphous nature, to low density poly(ethylene)/isotactic poly(propylene) (80/20) blend is demonstrated. This effect is expressed by the major improvement of mechanical properties of ternary blends as examined at a macroscopic size scale by means of tensile measurements. The structure investigation also reveals a clear dependence of the morphology on adding ethylene-copropylene polymer. Both the nature and the content of ethylene-co-propylene polymer affect structure and properties. It is further demonstrated that the extent of improvement in mechanical properties is to be related to the molecular details of the compatibilizer. Combination of high molecular weight and high ethylene content is appropriate for the studied system where the poly(ethylene) plays the role of matrix. A new way to characterize semicrystalline systems by means of Brillouin spectroscopy is presented in this study. By this method based on inelastic light scattering, we were able to measure the high frequency elastic constant (c11) of the two microphases in the case where the spherulites size is exhibit size larger than the size of the probing phonon wavelength. In this considered case, the sample film is inhomogeneous over the relevant length scales and there is an access to the transverse phonon in the crystalline phase yielding the elastic constant c44 as well. Isotactic poly(propylene) is well suited for this type of investigation since its morphology can be tailored through different thermal treatment from the melt. Two distinctly different types of films were used; quenched (low crystallinity) and annealed (high crystallinity). The Brillouin scattering data are discussed with respect to the spherulites size, lamellae thickness, long period, crystallinity degree and well documented by AFM images. The structure and the properties of isotactic poly(propylene) matrix modified by inorganic layered silicate, montmorillonite, are discussed with respect to the clay content. Isotactic poly(propylene)-graft-maleic anhydride was used as compatibilizer. It is clearly demonstrated that the property enhancement is largely due to the ability of layered silicate to exfoliate. The intimate dispersion of the nanometer-thick silicate result from a delicate balance of the content ratio between the isotactic poly(propylene)-graft-maleic anhydride compatibilizer and the inorganic clay.

Synthesis and characterization of structurally well-defined polymer-layered silicate nanocomposites

Zusammenfassung Nanokomposite aus Polymeren und Schichtsilikaten werden zumeist auf der Basis natürlicher Tone wie Montmorillonit hergestellt. Für NMR- und EPR-Untersuchungen der Tensidschicht, die das Silikat mit dem Polymer kompatibilisiert, ist der Eisengehalt natürlicher Tone jedoch abträglich, weil er zu einer Verkürzung der Relaxationszeiten und zu einer Linienverbreiterung in den Spektren führt. Dieses Problem konnte überwunden werden, indem als Silikatkomponente eisenfreies, strukturell wohldefiniertes Magadiit hydrothermal synthetisiert und für die Kompositbildung eingesetzt wurde. Die Morphologie des Magadiits wurde durch Rasterelektronenmikroskopie charakterisiert und der Interkalationsgrad von schmelzinterkalierten Polymer-Nanokompositen wurde durch Weitwinkelröntgenstreuung bestimmt. Polymere mit Carbonylgruppen scheinen leichter zu interkalieren als solche ohne Carbonylgruppen. Polycaprolacton interkalierte sowohl in Oragnomagadiite auf der Basis von Ammoniumtensiden als auch in solche auf der Basis von Phosphoniumtensiden. Die Dynamik auf einer Nanosekundenzeitskala und die Struktur der Tensidschicht wurden mittels ortsspezifisch spinmarkierter Tensidsonden unter Nutzung von Dauerstrich- (CW) und Puls-Methoden der elektronenparamagnetischen Resonanzspektroskopie (EPR) untersucht. Zusätzlich wurde die statische 2H-Kernmagnetresonanz (NMR) an spezifisch deuterierten Tensiden angewendet, um die Tensiddynamik auf einer komplementären Zeitskala zwischen Mikrosekunden und Millisekunden zu erfassen. Sowohl die CW-EPR- als auch die 2H-NMR-Ergebnisse zeigen eine Beschleunigung der Tensiddynamik durch Interkalation von Polycaprolacton auf, während sich in den nichtinterkalierten Mikrokompositen mit Polystyrol die Tensiddynamik verlangsamt. Die Rotationskorrelationszeiten und Aktivierungsenergien offenbaren verschiedene Regime der Tensiddynamik. In Polystyrol-Mikrokompositen entspricht die Übergangstemperatur zwischen den Regimen der Glasübergangstemperatur von Polystyrol, während sie in Polycaprolacton-Nanokompositen bei der Schmelztemperatur von Polycaprolacton liegt. Durch die erhebliche Verlängerung der Elektronenspin-Relaxationszeiten bei Verwendung von eisenfreiem Magadiit können Messdaten hoher Qualität mit Puls-EPR-Experimenten erhalten werden. Insebsondere wurden die Vier-Puls-Elektron-Elektron-Doppelresonanz (DEER), die Elektronenspinechoenveloppenmodulation (ESEEM) und die Elektronen-Kern-Doppelresonanz (ENDOR) an spinmarkierten sowie spezifisch deuterierten Tensiden angewandt. Die ENDOR-Ergebnisse legen ein Model der Tensidschicht nahe, in dem zusätzlich zu den Oberflächenlagen auf dem Silikat eine wohldefinierte mittlere Lage existiert. Dieses Modell erklärt auch Verdünnungseffekte durch das Polymer in Kompositen mit Polycaprolacton und Polystyrol. Die umfangreiche Information aus den Magnetresonanztechniken ergänzt die Information aus konventionellen Charakterisierungstechniken wie Röntgendiffraktion und Transmissionselektronenmikroskopie und führt so zu einem detaillierteren Bild der Struktur und Dynamik der Tensidschicht in Nanokompositen aus Polymeren und Schichtsilikaten.